diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/linux/regulator/driver.h | 4 | ||||
| -rw-r--r-- | include/linux/soc/qcom/smd-rpm.h | 1 | ||||
| -rw-r--r-- | include/linux/spi/spi.h | 9 |
3 files changed, 10 insertions, 4 deletions
diff --git a/include/linux/regulator/driver.h b/include/linux/regulator/driver.h index 9a911bb5fb61..29d920516e0b 100644 --- a/include/linux/regulator/driver.h +++ b/include/linux/regulator/driver.h @@ -277,9 +277,9 @@ enum regulator_type { * @curr_table: Current limit mapping table (if table based mapping) * * @vsel_range_reg: Register for range selector when using pickable ranges - * and regulator_regmap_X_voltage_X_pickable functions. + * and ``regulator_map_*_voltage_*_pickable`` functions. * @vsel_range_mask: Mask for register bitfield used for range selector - * @vsel_reg: Register for selector when using regulator_regmap_X_voltage_ + * @vsel_reg: Register for selector when using ``regulator_map_*_voltage_*`` * @vsel_mask: Mask for register bitfield used for selector * @vsel_step: Specify the resolution of selector stepping when setting * voltage. If 0, then no stepping is done (requested selector is diff --git a/include/linux/soc/qcom/smd-rpm.h b/include/linux/soc/qcom/smd-rpm.h index 9e4fdd861a51..da304ce8c8f7 100644 --- a/include/linux/soc/qcom/smd-rpm.h +++ b/include/linux/soc/qcom/smd-rpm.h @@ -10,6 +10,7 @@ struct qcom_smd_rpm; /* * Constants used for addressing resources in the RPM. */ +#define QCOM_SMD_RPM_BBYB 0x62796262 #define QCOM_SMD_RPM_BOBB 0x62626f62 #define QCOM_SMD_RPM_BOOST 0x61747362 #define QCOM_SMD_RPM_BUS_CLK 0x316b6c63 diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h index 6d16ba01ff5a..38286de779e3 100644 --- a/include/linux/spi/spi.h +++ b/include/linux/spi/spi.h @@ -135,6 +135,8 @@ extern int spi_delay_exec(struct spi_delay *_delay, struct spi_transfer *xfer); * @modalias: Name of the driver to use with this device, or an alias * for that name. This appears in the sysfs "modalias" attribute * for driver coldplugging, and in uevents used for hotplugging + * @driver_override: If the name of a driver is written to this attribute, then + * the device will bind to the named driver and only the named driver. * @cs_gpio: LEGACY: gpio number of the chipselect line (optional, -ENOENT when * not using a GPIO line) use cs_gpiod in new drivers by opting in on * the spi_master. @@ -443,6 +445,7 @@ static inline void spi_unregister_driver(struct spi_driver *sdrv) * @spi_transfer->ptp_sts_word_post were transmitted. * If the driver does not set this, the SPI core takes the snapshot as * close to the driver hand-over as possible. + * @irq_flags: Interrupt enable state during PTP system timestamping * * Each SPI controller can communicate with one or more @spi_device * children. These make a small bus, sharing MOSI, MISO and SCK signals @@ -481,6 +484,9 @@ struct spi_controller { /* spi_device.mode flags understood by this controller driver */ u32 mode_bits; + /* spi_device.mode flags override flags for this controller */ + u32 buswidth_override_bits; + /* bitmask of supported bits_per_word for transfers */ u32 bits_per_word_mask; #define SPI_BPW_MASK(bits) BIT((bits) - 1) @@ -930,8 +936,7 @@ struct spi_transfer { struct ptp_system_timestamp *ptp_sts; - bool timestamped_pre; - bool timestamped_post; + bool timestamped; struct list_head transfer_list; }; |