| Age | Commit message (Collapse) | Author |
|---|
|
Add support for SFP hotpluggable modules via phylink. This supports
both copper and optical SFP modules, which require different Serdes
modes in order to properly negotiate the link.
Optical SFP modules typically require the Serdes link to be talking
1000base-X mode - this is the gigabit ethernet mode defined by the
802.3 standard.
Copper SFP modules typically integrate a PHY in the module to convert
from Serdes to copper, and the PHY will be configured by the vendor
to either present a 1000base-X Serdes link (for fixed 1000base-T) or
a SGMII Serdes link. However, this is vendor defined, so we instead
detect the PHY, switch the link to SGMII mode, and use traditional
PHY based negotiation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- set port and port capability depending on connector type
- move autoneg mode setting to probe function
- set "supported" speed capabilities depending on reported ethernet
capabilities
- checks for short read
- dump eeprom base ID when checksum fails
|
|
Add wake-on-lan support to phylink.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add ethtool nway_reset support to phylink, to allow userspace to
request a re-negotiation of the link.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add support for reading and writing the clause 45 MII registers.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add support to phylink for SFP, which needs to control and configure
the ethernet MAC link state. Specifically, SFP needs to:
1. set the negotiation mode between SGMII and 1000base-X
2. attach and detach the module PHY
3. prevent the link coming up when errors are reported
In the absence of a PHY, we also need to set the ethtool port type
according to the module plugged in.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- rework phylink_set_link_*(), combining into a single function.
|
|
The link between the ethernet MAC and its PHY has become more complex
as the interface evolves. This is especially true with serdes links,
where the part of the PHY is effectively integrated into the MAC.
Serdes links can be connected to a variety of devices, including SFF
modules soldered down onto the board with the MAC, a SFP cage with
a hotpluggable SFP module which may contain a PHY or directly modulate
the serdes signals onto optical media with or without a PHY, or even
a classical PHY connection.
Moreover, the negotiation information on serdes links comes in two
varieties - SGMII mode, where the PHY provides its speed/duplex/flow
control information to the MAC, and 1000base-X mode where both ends
exchange their abilities and each resolve the link capabilities.
This means we need a more flexible means to support these arrangements,
particularly with the hotpluggable nature of SFP, where the PHY can
be attached or detached after the network device has been brought up.
Ethtool information can come from multiple sources:
- we may have a PHY operating in either SGMII or 1000base-X mode, in
which case we take ethtool/mii data directly from the PHY.
- we may have a optical SFP module without a PHY, with the MAC
operating in 1000base-X mode - the ethtool/mii data needs to come
from the MAC.
- we may have a copper SFP module with a PHY whic can't be accessed,
which means we need to take ethtool/mii data from the MAC.
Phylink aims to solve this by providing an intermediary between the
MAC and PHY, providing a safe way for PHYs to be hotplugged, and
allowing a SFP driver to reconfigure the serdes connection.
Phylink also takes over support of fixed link connections, where the
speed/duplex/flow control are fixed, but link status may be controlled
by a GPIO signal. By avoiding the fixed-phy implementation, phylink
can provide a faster response to link events: fixed-phy has to wait for
phylib to operate its state machine, which can take several seconds.
In comparison, phylink takes milliseconds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- remove sync status
- rework supported and advertisment handling
- add 1000base-x speed for fixed links
- use functionality exported from phy-core, reworking
__phylink_ethtool_ksettings_set for it
|
|
Add an I2C MDIO bus bridge library, to allow phylib to access PHYs which
are connected to an I2C bus instead of the more conventional MDIO bus.
Such PHYs can be found in SFP adapters and SFF modules.
Since PHYs appear at I2C bus address 0x40..0x5f, and 0x50/0x51 are
reserved for SFP EEPROMs/diagnostics, we must not allow the MDIO bus
to access these I2C addresses.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
phylink will need phy_start_machine exported, so lets export it as a
GPL symbol. Documentation/networking/phy.txt indicates that this
should be a PHY API function.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Sometimes, we need to do additional work between the PHY coming up and
marking the carrier present - for example, we may need to wait for the
PHY to MAC link to finish negotiation. This changes phylib to provide
a notification function pointer which avoids the built-in
netif_carrier_on() and netif_carrier_off() functions.
Standard ->adjust_link functionality is provided by hooking a helper
into the new ->phy_link_change method.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add the missing 1000Base-X entry to the phy settings table. This was
not included because the original code could not cope with more than
32 bits of link mode mask.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
phy-core
phy_lookup_setting() provides useful functionality in ethtool code
outside phylib. Move it to phy-core and allow it to be re-used (eg,
in phylink) rather than duplicated elsewhere. Note that this supports
the larger linkmode space.
As we move the phy settings table, we also need to move the guts of
phy_supported_speeds() as well.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Other code would like to make use of this, so make the speed and duplex
string generation visible, and place it in a separate file.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Allow the phy settings table to support more than 32 link modes by
switching to the ethtool link mode bit number representation, rather
than storing the mask. This will allow phylink and other ethtool
code to share the settings table to look up settings.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add phylib support for the Marvell Alaska X 10 Gigabit PHY (MV88X3310).
This phy is able to operate at 10G, 1G, 100M and 10M speeds, and only
supports Clause 45 accesses.
The PHY appears (based on the vendor IDs) to be two different vendors
IP, with each devad containing several instances.
This PHY driver has only been tested with the RJ45 copper port and a
Marvell Armada 8040-based ethernet interface.
It should be noted that to use the full range of speeds, MAC drivers
need to also reconfigure the link mode as per phydev->interface, since
the PHY automatically changes its interface mode depending on the
negotiated speed.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
XAUI allows XGMII to reach an extended distance by using a XGXS layer at
each end of the MAC to PHY link, operating over four Serdes lanes.
10GBASE-KR is a single lane Serdes backplane ethernet connection method
with autonegotiation on the link. Some PHYs use this to connect to the
ethernet interface at 10G speeds, switching to other connection types
when utilising slower speeds.
10GBASE-KR is also used for XFI and SFI to connect to XFP and SFP fiber
modules.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Move the old 10G genphy support to sit beside the new clause 45 library
functions, so all the 10G phy code is together.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
genphy_restart_aneg() can only restart autonegotiation on clause 22
PHYs. Add a phy_restart_aneg() function which selects between the
clause 22 and clause 45 restart functionality depending on the PHY
type.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add generic helpers for 802.3 clause 45 PHYs for >= 10Gbps support.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Simplify the loop in phy_supported_speeds().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
phylib has some undesirable behaviour when forcing a link mode through
ethtool. phylib uses this code:
idx = phy_find_valid(phy_find_setting(phydev->speed, phydev->duplex),
features);
to find an index in the settings table. phy_find_setting() starts at
index 0, and scans upwards looking for an exact speed and duplex match.
When it doesn't find it, it returns MAX_NUM_SETTINGS - 1, which is
10baseT-Half duplex.
phy_find_valid() then scans from the point (and effectively only checks
one entry) before bailing out, returning MAX_NUM_SETTINGS - 1.
phy_sanitize_settings() then sets ->speed to SPEED_10 and ->duplex to
DUPLEX_HALF whether or not 10baseT-Half is supported or not. This goes
against all the comments against these functions, and 10baseT-Half may
not even be supported by the hardware.
Rework these functions, introducing a new method of scanning the table.
There are two modes of lookup that phylib wants: exact, and inexact.
- in exact mode, we return either an exact match or failure
- in inexact mode, we return an exact match if it exists, a match at
the highest speed that is not greater than the requested speed
(ignoring duplex), or failing that, the lowest supported speed, or
failure.
The biggest difference is that we always check whether the entry is
supported before further consideration, so all unsupported entries are
not considered as candidates.
This results in arguably saner behaviour, better matches the comments,
and is probably what users would expect.
This becomes important as ethernet speeds increase, PHYs exist which do
not support the 10Mbit speeds, and half-duplex is likely to become
obsolete - it's already not even an option on 10Gbit and faster links.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
EEE is able to work in any PHY interface mode, there is nothing which
fundamentally restricts it to only a few modes. For example, EEE works
in SGMII mode with the Marvell 88E1512.
Rather than just adding SGMII mode to the list, Florian suggests
removing the list of interface modes entirely:
It actually sounds like we should just kill the check entirely,
it does not appear that any of the interface mode would not
fundamentally be able to support EEE, because the "lowest" mode
we support is MII, and even there it's quite possible to support
EEE.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
When the EEE advertisment is changed, we should restart autonegotiation
to update the link partner with the new EEE settings. Add this trigger
but only if the advertisment has changed.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
We currently allow userspace to set any EEE advertisments it desires,
whether or not the PHY supports them. For example:
# ethtool --set-eee eth1 advertise 0xffffffff
# ethtool --show-eee eth1
EEE Settings for eth1:
EEE status: disabled
Tx LPI: disabled
Supported EEE link modes: 100baseT/Full
1000baseT/Full
10000baseT/Full
Advertised EEE link modes: 100baseT/Full
1000baseT/Full
1000baseKX/Full
10000baseT/Full
10000baseKX4/Full
10000baseKR/Full
Clearly, this is not sane, we should only allow link modes that are
supported to be advertised (as we do elsewhere.) Ensure that we mask
the MDIO_AN_EEE_ADV value with the capabilities retrieved from the
MDIO_PCS_EEE_ABLE register.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Make mmd_phy_indirect() use the same terminology as the rest of the
code, making clear what each address is - phy address, devad, and
register number.
While here, remove the "inline" from this static function, leaving
it to the compiler to decide whether to inline this function, and
get rid of unnecessary parens.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Remove the indirect MMD read/write methods which are now no longer
necessary.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Prepare to remove the indirect MMD accessors; code them in terms of the
simpler accessors, and mark the indirect ones deprecated to avoid new
users.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Convert micrel to the new read_mmd/write_mmd driver methods. This
Clause 22 PHY does not support any MMD access method.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Switch everyone over to using phy_read_mmd() and phy_write_mmd() now
that they are able to handle both Clause 22 indirect addressing and
Clause 45 direct addressing methods to the MMD registers.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
lan78xx appears to use phylib in a rather weird way, accessing the PHY
partly through phylib, and partly by making direct accesses to it,
including to the Clause 45 registers. As the indirect MMD accessors are
going away, update this driver to use the plain phy_(read|write)_mmd()
accessors instead.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Make phy_(read|write)_mmd() generic 802.3 clause 45 register accessors
for both Clause 22 and Clause 45 PHYs, using either the direct register
reading for Clause 45, or the indirect method for Clause 22 PHYs.
Allow this behaviour to be overriden by PHY drivers where necessary.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Move the phy_(read|write)__mmd() helpers out of line, they will become
our main MMD accessor functions, and so will be a little more complex.
This complexity doesn't belong in an inline function. Also move the
_indirect variants as well to keep like functionality together.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"The final fixes for 4.11:
- prevent a triple fault with function graph tracing triggered via
suspend to ram
- prevent optimizing for size when function graph tracing is enabled
and the compiler does not support -mfentry
- prevent mwaitx() being called with a zero timeout as mwaitx() might
never return. Observed on the new Ryzen CPUs"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Prevent timer value 0 for MWAITX
x86/build: convert function graph '-Os' error to warning
ftrace/x86: Fix triple fault with graph tracing and suspend-to-ram
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Thomas Gleixner:
"A single fix for a cputime accounting regression which got introduced
in the 4.11 cycle"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/cputime: Fix ksoftirqd cputime accounting regression
|
|
Newer hardware has uncovered a bug in the software implementation of
using MWAITX for the delay function. A value of 0 for the timer is meant
to indicate that a timeout will not be used to exit MWAITX. On newer
hardware this can result in MWAITX never returning, resulting in NMI
soft lockup messages being printed. On older hardware, some of the other
conditions under which MWAITX can exit masked this issue. The AMD APM
does not currently document this and will be updated.
Please refer to http://marc.info/?l=kvm&m=148950623231140 for
information regarding NMI soft lockup messages on an AMD Ryzen 1800X.
This has been root-caused as a 0 passed to MWAITX causing it to wait
indefinitely.
This change has the added benefit of avoiding the unnecessary setup of
MONITORX/MWAITX when the delay value is zero.
Signed-off-by: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Link: http://lkml.kernel.org/r/1493156643-29366-1-git-send-email-Janakarajan.Natarajan@amd.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull iov iter fix from Al Viro.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix a braino in ITER_PIPE iov_iter_revert()
|
|
Fixes: 27c0e3748e41
Tested-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One odd config build fix for a recent Allwinner clock driver change
that got merged. The common code called code in another file that
wasn't always built. This just forces it on so people don't run into
this bad configuration"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: sunxi-ng: always select CCU_GATE
|
|
Pull networking fixes from David Miller:
"Just a couple more stragglers, I really hope this is it.
1) Don't let frags slip down into the GRO segmentation handlers, from
Steffen Klassert.
2) Truesize under-estimation triggers warnings in TCP over loopback
with socket filters, 2 part fix from Eric Dumazet.
3) Fix undesirable reset of bonding MTU to ETH_HLEN on slave removal,
from Paolo Abeni.
4) If we flush the XFRM policy after garbage collection, it doesn't
work because stray entries can be created afterwards. Fix from Xin
Long.
5) Hung socket connection fixes in TIPC from Parthasarathy Bhuvaragan.
6) Fix GRO regression with IPSEC when netfilter is disabled, from
Sabrina Dubroca.
7) Fix cpsw driver Kconfig dependency regression, from Arnd Bergmann"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: hso: register netdev later to avoid a race condition
net: adjust skb->truesize in ___pskb_trim()
tcp: do not underestimate skb->truesize in tcp_trim_head()
bonding: avoid defaulting hard_header_len to ETH_HLEN on slave removal
ipv4: Don't pass IP fragments to upper layer GRO handlers.
cpsw/netcp: refine cpts dependency
tipc: close the connection if protocol messages contain errors
tipc: improve error validations for sockets in CONNECTING state
tipc: Fix missing connection request handling
xfrm: fix GRO for !CONFIG_NETFILTER
xfrm: do the garbage collection after flushing policy
|
|
If the netdev is accessed before the urbs are initialized,
there will be NULL pointer dereferences. That is avoided by
registering it when it is fully initialized.
This case occurs e.g. if dhcpcd is running in the background
and the device is probed, either after insmod hso or
when the device appears on the usb bus.
A backtrace is the following:
[ 1357.356048] usb 1-2: new high-speed USB device number 12 using ehci-omap
[ 1357.551177] usb 1-2: New USB device found, idVendor=0af0, idProduct=8800
[ 1357.558654] usb 1-2: New USB device strings: Mfr=3, Product=2, SerialNumber=0
[ 1357.568572] usb 1-2: Product: Globetrotter HSUPA Modem
[ 1357.574096] usb 1-2: Manufacturer: Option N.V.
[ 1357.685882] hso 1-2:1.5: Not our interface
[ 1460.886352] hso: unloaded
[ 1460.889984] usbcore: deregistering interface driver hso
[ 1513.769134] hso: ../drivers/net/usb/hso.c: Option Wireless
[ 1513.846771] Unable to handle kernel NULL pointer dereference at virtual address 00000030
[ 1513.887664] hso 1-2:1.5: Not our interface
[ 1513.906890] usbcore: registered new interface driver hso
[ 1513.937988] pgd = ecdec000
[ 1513.949890] [00000030] *pgd=acd15831, *pte=00000000, *ppte=00000000
[ 1513.956573] Internal error: Oops: 817 [#1] PREEMPT SMP ARM
[ 1513.962371] Modules linked in: hso usb_f_ecm omap2430 bnep bluetooth g_ether usb_f_rndis u_ether libcomposite configfs ipv6 arc4 wl18xx wlcore mac80211 cfg80211 bq27xxx_battery panel_tpo_td028ttec1 omapdrm drm_kms_helper cfbfillrect snd_soc_simple_card syscopyarea cfbimgblt snd_soc_simple_card_utils sysfillrect sysimgblt fb_sys_fops snd_soc_omap_twl4030 cfbcopyarea encoder_opa362 drm twl4030_madc_hwmon wwan_on_off snd_soc_gtm601 pwm_omap_dmtimer generic_adc_battery connector_analog_tv pwm_bl extcon_gpio omap3_isp wlcore_sdio videobuf2_dma_contig videobuf2_memops w1_bq27000 videobuf2_v4l2 videobuf2_core omap_hdq snd_soc_omap_mcbsp ov9650 snd_soc_omap bmp280_i2c bmg160_i2c v4l2_common snd_pcm_dmaengine bmp280 bmg160_core at24 bmc150_magn_i2c nvmem_core videodev phy_twl4030_usb bmc150_accel_i2c tsc2007
[ 1514.037384] bmc150_magn bmc150_accel_core media leds_tca6507 bno055 industrialio_triggered_buffer kfifo_buf gpio_twl4030 musb_hdrc snd_soc_twl4030 twl4030_vibra twl4030_madc twl4030_pwrbutton twl4030_charger industrialio w2sg0004 ehci_omap omapdss [last unloaded: hso]
[ 1514.062622] CPU: 0 PID: 3433 Comm: dhcpcd Tainted: G W 4.11.0-rc8-letux+ #1
[ 1514.071136] Hardware name: Generic OMAP36xx (Flattened Device Tree)
[ 1514.077758] task: ee748240 task.stack: ecdd6000
[ 1514.082580] PC is at hso_start_net_device+0x50/0xc0 [hso]
[ 1514.088287] LR is at hso_net_open+0x68/0x84 [hso]
[ 1514.093231] pc : [<bf79c304>] lr : [<bf79ced8>] psr: a00f0013
sp : ecdd7e20 ip : 00000000 fp : ffffffff
[ 1514.105316] r10: 00000000 r9 : ed0e080c r8 : ecd8fe2c
[ 1514.110839] r7 : bf79cef4 r6 : ecd8fe00 r5 : 00000000 r4 : ed0dbd80
[ 1514.117706] r3 : 00000000 r2 : c0020c80 r1 : 00000000 r0 : ecdb7800
[ 1514.124572] Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[ 1514.132110] Control: 10c5387d Table: acdec019 DAC: 00000051
[ 1514.138153] Process dhcpcd (pid: 3433, stack limit = 0xecdd6218)
[ 1514.144470] Stack: (0xecdd7e20 to 0xecdd8000)
[ 1514.149078] 7e20: ed0dbd80 ecd8fe98 00000001 00000000 ecd8f800 ecd8fe00 ecd8fe60 00000000
[ 1514.157714] 7e40: ed0e080c bf79ced8 bf79ce70 ecd8f800 00000001 bf7a0258 ecd8f830 c068d958
[ 1514.166320] 7e60: c068d8b8 ecd8f800 00000001 00001091 00001090 c068dba4 ecd8f800 00001090
[ 1514.174926] 7e80: ecd8f940 ecd8f800 00000000 c068dc60 00000000 00000001 ed0e0800 ecd8f800
[ 1514.183563] 7ea0: 00000000 c06feaa8 c0ca39c2 beea57dc 00000020 00000000 306f7368 00000000
[ 1514.192169] 7ec0: 00000000 00000000 00001091 00000000 00000000 00000000 00000000 00008914
[ 1514.200805] 7ee0: eaa9ab60 beea57dc c0c9bfc0 eaa9ab40 00000006 00000000 00046858 c066a948
[ 1514.209411] 7f00: beea57dc eaa9ab60 ecc6b0c0 c02837b0 00000006 c0282c90 0000c000 c0283654
[ 1514.218017] 7f20: c09b0c00 c098bc31 00000001 c0c5e513 c0c5e513 00000000 c0151354 c01a20c0
[ 1514.226654] 7f40: c0c5e513 c01a3134 ecdd6000 c01a3160 ee7487f0 600f0013 00000000 ee748240
[ 1514.235260] 7f60: ee748734 00000000 ecc6b0c0 ecc6b0c0 beea57dc 00008914 00000006 00000000
[ 1514.243896] 7f80: 00046858 c02837b0 00001091 0003a1f0 00046608 0003a248 00000036 c01071e4
[ 1514.252502] 7fa0: ecdd6000 c0107040 0003a1f0 00046608 00000006 00008914 beea57dc 00001091
[ 1514.261108] 7fc0: 0003a1f0 00046608 0003a248 00000036 0003ac0c 00046608 00046610 00046858
[ 1514.269744] 7fe0: 0003a0ac beea57d4 000167eb b6f23106 400f0030 00000006 00000000 00000000
[ 1514.278411] [<bf79c304>] (hso_start_net_device [hso]) from [<bf79ced8>] (hso_net_open+0x68/0x84 [hso])
[ 1514.288238] [<bf79ced8>] (hso_net_open [hso]) from [<c068d958>] (__dev_open+0xa0/0xf4)
[ 1514.296600] [<c068d958>] (__dev_open) from [<c068dba4>] (__dev_change_flags+0x8c/0x130)
[ 1514.305023] [<c068dba4>] (__dev_change_flags) from [<c068dc60>] (dev_change_flags+0x18/0x48)
[ 1514.313934] [<c068dc60>] (dev_change_flags) from [<c06feaa8>] (devinet_ioctl+0x348/0x714)
[ 1514.322540] [<c06feaa8>] (devinet_ioctl) from [<c066a948>] (sock_ioctl+0x2b0/0x308)
[ 1514.330627] [<c066a948>] (sock_ioctl) from [<c0282c90>] (vfs_ioctl+0x20/0x34)
[ 1514.338165] [<c0282c90>] (vfs_ioctl) from [<c0283654>] (do_vfs_ioctl+0x82c/0x93c)
[ 1514.346038] [<c0283654>] (do_vfs_ioctl) from [<c02837b0>] (SyS_ioctl+0x4c/0x74)
[ 1514.353759] [<c02837b0>] (SyS_ioctl) from [<c0107040>] (ret_fast_syscall+0x0/0x1c)
[ 1514.361755] Code: e3822103 e3822080 e1822781 e5981014 (e5832030)
[ 1514.510833] ---[ end trace dfb3e53c657f34a0 ]---
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Andrey found a way to trigger the WARN_ON_ONCE(delta < len) in
skb_try_coalesce() using syzkaller and a filter attached to a TCP
socket.
As we did recently in commit 158f323b9868 ("net: adjust skb->truesize in
pskb_expand_head()") we can adjust skb->truesize from ___pskb_trim(),
via a call to skb_condense().
If all frags were freed, then skb->truesize can be recomputed.
This call can be done if skb is not yet owned, or destructor is
sock_edemux().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Andrey found a way to trigger the WARN_ON_ONCE(delta < len) in
skb_try_coalesce() using syzkaller and a filter attached to a TCP
socket over loopback interface.
I believe one issue with looped skbs is that tcp_trim_head() can end up
producing skb with under estimated truesize.
It hardly matters for normal conditions, since packets sent over
loopback are never truncated.
Bytes trimmed from skb->head should not change skb truesize, since
skb->head is not reallocated.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On slave list updates, the bonding driver computes its hard_header_len
as the maximum of all enslaved devices's hard_header_len.
If the slave list is empty, e.g. on last enslaved device removal,
ETH_HLEN is used.
Since the bonding header_ops are set only when the first enslaved
device is attached, the above can lead to header_ops->create()
being called with the wrong skb headroom in place.
If bond0 is configured on top of ipoib devices, with the
following commands:
ifup bond0
for slave in $BOND_SLAVES_LIST; do
ip link set dev $slave nomaster
done
ping -c 1 <ip on bond0 subnet>
we will obtain a skb_under_panic() with a similar call trace:
skb_push+0x3d/0x40
push_pseudo_header+0x17/0x30 [ib_ipoib]
ipoib_hard_header+0x4e/0x80 [ib_ipoib]
arp_create+0x12f/0x220
arp_send_dst.part.19+0x28/0x50
arp_solicit+0x115/0x290
neigh_probe+0x4d/0x70
__neigh_event_send+0xa7/0x230
neigh_resolve_output+0x12e/0x1c0
ip_finish_output2+0x14b/0x390
ip_finish_output+0x136/0x1e0
ip_output+0x76/0xe0
ip_local_out+0x35/0x40
ip_send_skb+0x19/0x40
ip_push_pending_frames+0x33/0x40
raw_sendmsg+0x7d3/0xb50
inet_sendmsg+0x31/0xb0
sock_sendmsg+0x38/0x50
SYSC_sendto+0x102/0x190
SyS_sendto+0xe/0x10
do_syscall_64+0x67/0x180
entry_SYSCALL64_slow_path+0x25/0x25
This change addresses the issue avoiding updating the bonding device
hard_header_len when the slaves list become empty, forbidding to
shrink it below the value used by header_ops->create().
The bug is there since commit 54ef31371407 ("[PATCH] bonding: Handle large
hard_header_len") but the panic can be triggered only since
commit fc791b633515 ("IB/ipoib: move back IB LL address into the hard
header").
Reported-by: Norbert P <noe@physik.uzh.ch>
Fixes: 54ef31371407 ("[PATCH] bonding: Handle large hard_header_len")
Fixes: fc791b633515 ("IB/ipoib: move back IB LL address into the hard header")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Upper layer GRO handlers can not handle IP fragments, so
exit GRO processing in this case.
This fixes ESP GRO because the packet must be reassembled
before we can decapsulate, otherwise we get authentication
failures.
It also aligns IPv4 to IPv6 where packets with fragmentation
headers are not passed to upper layer GRO handlers.
Fixes: 7785bba299a8 ("esp: Add a software GRO codepath")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tony Lindgren reports a kernel oops that resulted from my compile-time
fix on the default config. This shows two problems:
a) configurations that did not already enable PTP_1588_CLOCK will
now miss the cpts driver
b) when cpts support is disabled, the driver crashes. This is a
preexisting problem that we did not notice before my patch.
While the second problem is still being investigated, this modifies
the dependencies again, getting us back to the original state, with
another 'select NET_PTP_CLASSIFY' added in to avoid the original
link error we got, and the 'depends on POSIX_TIMERS' to hide
the CPTS support when turning it on would be useless.
Cc: stable@vger.kernel.org # 4.11 needs this
Fixes: 07fef3623407 ("cpsw/netcp: cpts depends on posix_timers")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2017-04-28
1) Do garbage collecting after a policy flush to remove old
bundles immediately. From Xin Long.
2) Fix GRO if netfilter is not defined.
From Sabrina Dubroca.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fix from Dmitry Torokhov:
"Yet another quirk to i8042 to get touchpad recognized on some laptops"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - add Clevo P650RS to the i8042 reset list
|
|
When the base driver is enabled but all SoC specific drivers are turned
off, we now get a build error after code was added to always refer to the
clk gates:
drivers/clk/built-in.o: In function `ccu_pll_notifier_cb':
:(.text+0x154f8): undefined reference to `ccu_gate_helper_disable'
:(.text+0x15504): undefined reference to `ccu_gate_helper_enable'
This changes the Kconfig to always require the gate code to be built-in
when CONFIG_SUNXI_CCU is set.
Fixes: 02ae2bc6febd ("clk: sunxi-ng: Add clk notifier to gate then ungate PLL clocks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fix from Chris Mason:
"We have one more fix for btrfs.
This gets rid of a new WARN_ON from rc1 that ended up making more
noise than we really want. The larger fix for the underflow got
delayed a bit and it's better for now to put it under
CONFIG_BTRFS_DEBUG"
* 'for-linus-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: qgroup: move noisy underflow warning to debugging build
|
|
Parthasarathy Bhuvaragan says:
====================
tipc: fix hanging socket connections
This patch series contains fixes for the socket layer to
prevent hanging / stale connections.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
