| Age | Commit message (Collapse) | Author |
|---|
|
genphy_restart_aneg() can only restart autonegotiation on clause 22
PHYs. Add a phy_restart_aneg() function which selects between the
clause 22 and clause 45 restart functionality depending on the PHY
type.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add generic helpers for 802.3 clause 45 PHYs for >= 10Gbps support.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Simplify the loop in phy_supported_speeds().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
phylib has some undesirable behaviour when forcing a link mode through
ethtool. phylib uses this code:
idx = phy_find_valid(phy_find_setting(phydev->speed, phydev->duplex),
features);
to find an index in the settings table. phy_find_setting() starts at
index 0, and scans upwards looking for an exact speed and duplex match.
When it doesn't find it, it returns MAX_NUM_SETTINGS - 1, which is
10baseT-Half duplex.
phy_find_valid() then scans from the point (and effectively only checks
one entry) before bailing out, returning MAX_NUM_SETTINGS - 1.
phy_sanitize_settings() then sets ->speed to SPEED_10 and ->duplex to
DUPLEX_HALF whether or not 10baseT-Half is supported or not. This goes
against all the comments against these functions, and 10baseT-Half may
not even be supported by the hardware.
Rework these functions, introducing a new method of scanning the table.
There are two modes of lookup that phylib wants: exact, and inexact.
- in exact mode, we return either an exact match or failure
- in inexact mode, we return an exact match if it exists, a match at
the highest speed that is not greater than the requested speed
(ignoring duplex), or failing that, the lowest supported speed, or
failure.
The biggest difference is that we always check whether the entry is
supported before further consideration, so all unsupported entries are
not considered as candidates.
This results in arguably saner behaviour, better matches the comments,
and is probably what users would expect.
This becomes important as ethernet speeds increase, PHYs exist which do
not support the 10Mbit speeds, and half-duplex is likely to become
obsolete - it's already not even an option on 10Gbit and faster links.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
EEE is able to work in any PHY interface mode, there is nothing which
fundamentally restricts it to only a few modes. For example, EEE works
in SGMII mode with the Marvell 88E1512.
Rather than just adding SGMII mode to the list, Florian suggests
removing the list of interface modes entirely:
It actually sounds like we should just kill the check entirely,
it does not appear that any of the interface mode would not
fundamentally be able to support EEE, because the "lowest" mode
we support is MII, and even there it's quite possible to support
EEE.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
When the EEE advertisment is changed, we should restart autonegotiation
to update the link partner with the new EEE settings. Add this trigger
but only if the advertisment has changed.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
We currently allow userspace to set any EEE advertisments it desires,
whether or not the PHY supports them. For example:
# ethtool --set-eee eth1 advertise 0xffffffff
# ethtool --show-eee eth1
EEE Settings for eth1:
EEE status: disabled
Tx LPI: disabled
Supported EEE link modes: 100baseT/Full
1000baseT/Full
10000baseT/Full
Advertised EEE link modes: 100baseT/Full
1000baseT/Full
1000baseKX/Full
10000baseT/Full
10000baseKX4/Full
10000baseKR/Full
Clearly, this is not sane, we should only allow link modes that are
supported to be advertised (as we do elsewhere.) Ensure that we mask
the MDIO_AN_EEE_ADV value with the capabilities retrieved from the
MDIO_PCS_EEE_ABLE register.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Make mmd_phy_indirect() use the same terminology as the rest of the
code, making clear what each address is - phy address, devad, and
register number.
While here, remove the "inline" from this static function, leaving
it to the compiler to decide whether to inline this function, and
get rid of unnecessary parens.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Remove the indirect MMD read/write methods which are now no longer
necessary.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Prepare to remove the indirect MMD accessors; code them in terms of the
simpler accessors, and mark the indirect ones deprecated to avoid new
users.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Convert micrel to the new read_mmd/write_mmd driver methods. This
Clause 22 PHY does not support any MMD access method.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Switch everyone over to using phy_read_mmd() and phy_write_mmd() now
that they are able to handle both Clause 22 indirect addressing and
Clause 45 direct addressing methods to the MMD registers.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
lan78xx appears to use phylib in a rather weird way, accessing the PHY
partly through phylib, and partly by making direct accesses to it,
including to the Clause 45 registers. As the indirect MMD accessors are
going away, update this driver to use the plain phy_(read|write)_mmd()
accessors instead.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Make phy_(read|write)_mmd() generic 802.3 clause 45 register accessors
for both Clause 22 and Clause 45 PHYs, using either the direct register
reading for Clause 45, or the indirect method for Clause 22 PHYs.
Allow this behaviour to be overriden by PHY drivers where necessary.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Move the phy_(read|write)__mmd() helpers out of line, they will become
our main MMD accessor functions, and so will be a little more complex.
This complexity doesn't belong in an inline function. Also move the
_indirect variants as well to keep like functionality together.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
If the port reports that the link is up while we are resetting, there's
little point in waiting for the full duration.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
It seems on later Armada 38x, the slot clock configuration bit is not
read-only, but can be written. This means that our RW1C protection
ends up clearing this bit when the link control register is written.
Adjust the mask so that we only avoid writing '1' bits to the RW1C
bits of this register (bits 15 and 14 of the link status) rather than
masking out all the status register bits.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The cpuidle ->enter method expects the return value to be the sleep
state we entered. Returning negative numbers or other codes is not
permissible since coupled CPU idle was merged.
At least some of the mvebu_v7_cpu_suspend() implementations return the
value from cpu_suspend(), which returns zero if the CPU vectors back
into the kernel via cpu_resume() (the success case), or the non-zero
return value of the suspend actor, or one (failure cases).
We do not want to be returning the failure case value back to CPU idle
as that indicates that we successfully entered one of the deeper idle
states. Always return zero instead, indicating that we slept for the
shortest amount of time.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"The final fixes for 4.11:
- prevent a triple fault with function graph tracing triggered via
suspend to ram
- prevent optimizing for size when function graph tracing is enabled
and the compiler does not support -mfentry
- prevent mwaitx() being called with a zero timeout as mwaitx() might
never return. Observed on the new Ryzen CPUs"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Prevent timer value 0 for MWAITX
x86/build: convert function graph '-Os' error to warning
ftrace/x86: Fix triple fault with graph tracing and suspend-to-ram
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Thomas Gleixner:
"A single fix for a cputime accounting regression which got introduced
in the 4.11 cycle"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/cputime: Fix ksoftirqd cputime accounting regression
|
|
Newer hardware has uncovered a bug in the software implementation of
using MWAITX for the delay function. A value of 0 for the timer is meant
to indicate that a timeout will not be used to exit MWAITX. On newer
hardware this can result in MWAITX never returning, resulting in NMI
soft lockup messages being printed. On older hardware, some of the other
conditions under which MWAITX can exit masked this issue. The AMD APM
does not currently document this and will be updated.
Please refer to http://marc.info/?l=kvm&m=148950623231140 for
information regarding NMI soft lockup messages on an AMD Ryzen 1800X.
This has been root-caused as a 0 passed to MWAITX causing it to wait
indefinitely.
This change has the added benefit of avoiding the unnecessary setup of
MONITORX/MWAITX when the delay value is zero.
Signed-off-by: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Link: http://lkml.kernel.org/r/1493156643-29366-1-git-send-email-Janakarajan.Natarajan@amd.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull iov iter fix from Al Viro.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix a braino in ITER_PIPE iov_iter_revert()
|
|
Fixes: 27c0e3748e41
Tested-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One odd config build fix for a recent Allwinner clock driver change
that got merged. The common code called code in another file that
wasn't always built. This just forces it on so people don't run into
this bad configuration"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: sunxi-ng: always select CCU_GATE
|
|
Pull networking fixes from David Miller:
"Just a couple more stragglers, I really hope this is it.
1) Don't let frags slip down into the GRO segmentation handlers, from
Steffen Klassert.
2) Truesize under-estimation triggers warnings in TCP over loopback
with socket filters, 2 part fix from Eric Dumazet.
3) Fix undesirable reset of bonding MTU to ETH_HLEN on slave removal,
from Paolo Abeni.
4) If we flush the XFRM policy after garbage collection, it doesn't
work because stray entries can be created afterwards. Fix from Xin
Long.
5) Hung socket connection fixes in TIPC from Parthasarathy Bhuvaragan.
6) Fix GRO regression with IPSEC when netfilter is disabled, from
Sabrina Dubroca.
7) Fix cpsw driver Kconfig dependency regression, from Arnd Bergmann"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: hso: register netdev later to avoid a race condition
net: adjust skb->truesize in ___pskb_trim()
tcp: do not underestimate skb->truesize in tcp_trim_head()
bonding: avoid defaulting hard_header_len to ETH_HLEN on slave removal
ipv4: Don't pass IP fragments to upper layer GRO handlers.
cpsw/netcp: refine cpts dependency
tipc: close the connection if protocol messages contain errors
tipc: improve error validations for sockets in CONNECTING state
tipc: Fix missing connection request handling
xfrm: fix GRO for !CONFIG_NETFILTER
xfrm: do the garbage collection after flushing policy
|
|
If the netdev is accessed before the urbs are initialized,
there will be NULL pointer dereferences. That is avoided by
registering it when it is fully initialized.
This case occurs e.g. if dhcpcd is running in the background
and the device is probed, either after insmod hso or
when the device appears on the usb bus.
A backtrace is the following:
[ 1357.356048] usb 1-2: new high-speed USB device number 12 using ehci-omap
[ 1357.551177] usb 1-2: New USB device found, idVendor=0af0, idProduct=8800
[ 1357.558654] usb 1-2: New USB device strings: Mfr=3, Product=2, SerialNumber=0
[ 1357.568572] usb 1-2: Product: Globetrotter HSUPA Modem
[ 1357.574096] usb 1-2: Manufacturer: Option N.V.
[ 1357.685882] hso 1-2:1.5: Not our interface
[ 1460.886352] hso: unloaded
[ 1460.889984] usbcore: deregistering interface driver hso
[ 1513.769134] hso: ../drivers/net/usb/hso.c: Option Wireless
[ 1513.846771] Unable to handle kernel NULL pointer dereference at virtual address 00000030
[ 1513.887664] hso 1-2:1.5: Not our interface
[ 1513.906890] usbcore: registered new interface driver hso
[ 1513.937988] pgd = ecdec000
[ 1513.949890] [00000030] *pgd=acd15831, *pte=00000000, *ppte=00000000
[ 1513.956573] Internal error: Oops: 817 [#1] PREEMPT SMP ARM
[ 1513.962371] Modules linked in: hso usb_f_ecm omap2430 bnep bluetooth g_ether usb_f_rndis u_ether libcomposite configfs ipv6 arc4 wl18xx wlcore mac80211 cfg80211 bq27xxx_battery panel_tpo_td028ttec1 omapdrm drm_kms_helper cfbfillrect snd_soc_simple_card syscopyarea cfbimgblt snd_soc_simple_card_utils sysfillrect sysimgblt fb_sys_fops snd_soc_omap_twl4030 cfbcopyarea encoder_opa362 drm twl4030_madc_hwmon wwan_on_off snd_soc_gtm601 pwm_omap_dmtimer generic_adc_battery connector_analog_tv pwm_bl extcon_gpio omap3_isp wlcore_sdio videobuf2_dma_contig videobuf2_memops w1_bq27000 videobuf2_v4l2 videobuf2_core omap_hdq snd_soc_omap_mcbsp ov9650 snd_soc_omap bmp280_i2c bmg160_i2c v4l2_common snd_pcm_dmaengine bmp280 bmg160_core at24 bmc150_magn_i2c nvmem_core videodev phy_twl4030_usb bmc150_accel_i2c tsc2007
[ 1514.037384] bmc150_magn bmc150_accel_core media leds_tca6507 bno055 industrialio_triggered_buffer kfifo_buf gpio_twl4030 musb_hdrc snd_soc_twl4030 twl4030_vibra twl4030_madc twl4030_pwrbutton twl4030_charger industrialio w2sg0004 ehci_omap omapdss [last unloaded: hso]
[ 1514.062622] CPU: 0 PID: 3433 Comm: dhcpcd Tainted: G W 4.11.0-rc8-letux+ #1
[ 1514.071136] Hardware name: Generic OMAP36xx (Flattened Device Tree)
[ 1514.077758] task: ee748240 task.stack: ecdd6000
[ 1514.082580] PC is at hso_start_net_device+0x50/0xc0 [hso]
[ 1514.088287] LR is at hso_net_open+0x68/0x84 [hso]
[ 1514.093231] pc : [<bf79c304>] lr : [<bf79ced8>] psr: a00f0013
sp : ecdd7e20 ip : 00000000 fp : ffffffff
[ 1514.105316] r10: 00000000 r9 : ed0e080c r8 : ecd8fe2c
[ 1514.110839] r7 : bf79cef4 r6 : ecd8fe00 r5 : 00000000 r4 : ed0dbd80
[ 1514.117706] r3 : 00000000 r2 : c0020c80 r1 : 00000000 r0 : ecdb7800
[ 1514.124572] Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[ 1514.132110] Control: 10c5387d Table: acdec019 DAC: 00000051
[ 1514.138153] Process dhcpcd (pid: 3433, stack limit = 0xecdd6218)
[ 1514.144470] Stack: (0xecdd7e20 to 0xecdd8000)
[ 1514.149078] 7e20: ed0dbd80 ecd8fe98 00000001 00000000 ecd8f800 ecd8fe00 ecd8fe60 00000000
[ 1514.157714] 7e40: ed0e080c bf79ced8 bf79ce70 ecd8f800 00000001 bf7a0258 ecd8f830 c068d958
[ 1514.166320] 7e60: c068d8b8 ecd8f800 00000001 00001091 00001090 c068dba4 ecd8f800 00001090
[ 1514.174926] 7e80: ecd8f940 ecd8f800 00000000 c068dc60 00000000 00000001 ed0e0800 ecd8f800
[ 1514.183563] 7ea0: 00000000 c06feaa8 c0ca39c2 beea57dc 00000020 00000000 306f7368 00000000
[ 1514.192169] 7ec0: 00000000 00000000 00001091 00000000 00000000 00000000 00000000 00008914
[ 1514.200805] 7ee0: eaa9ab60 beea57dc c0c9bfc0 eaa9ab40 00000006 00000000 00046858 c066a948
[ 1514.209411] 7f00: beea57dc eaa9ab60 ecc6b0c0 c02837b0 00000006 c0282c90 0000c000 c0283654
[ 1514.218017] 7f20: c09b0c00 c098bc31 00000001 c0c5e513 c0c5e513 00000000 c0151354 c01a20c0
[ 1514.226654] 7f40: c0c5e513 c01a3134 ecdd6000 c01a3160 ee7487f0 600f0013 00000000 ee748240
[ 1514.235260] 7f60: ee748734 00000000 ecc6b0c0 ecc6b0c0 beea57dc 00008914 00000006 00000000
[ 1514.243896] 7f80: 00046858 c02837b0 00001091 0003a1f0 00046608 0003a248 00000036 c01071e4
[ 1514.252502] 7fa0: ecdd6000 c0107040 0003a1f0 00046608 00000006 00008914 beea57dc 00001091
[ 1514.261108] 7fc0: 0003a1f0 00046608 0003a248 00000036 0003ac0c 00046608 00046610 00046858
[ 1514.269744] 7fe0: 0003a0ac beea57d4 000167eb b6f23106 400f0030 00000006 00000000 00000000
[ 1514.278411] [<bf79c304>] (hso_start_net_device [hso]) from [<bf79ced8>] (hso_net_open+0x68/0x84 [hso])
[ 1514.288238] [<bf79ced8>] (hso_net_open [hso]) from [<c068d958>] (__dev_open+0xa0/0xf4)
[ 1514.296600] [<c068d958>] (__dev_open) from [<c068dba4>] (__dev_change_flags+0x8c/0x130)
[ 1514.305023] [<c068dba4>] (__dev_change_flags) from [<c068dc60>] (dev_change_flags+0x18/0x48)
[ 1514.313934] [<c068dc60>] (dev_change_flags) from [<c06feaa8>] (devinet_ioctl+0x348/0x714)
[ 1514.322540] [<c06feaa8>] (devinet_ioctl) from [<c066a948>] (sock_ioctl+0x2b0/0x308)
[ 1514.330627] [<c066a948>] (sock_ioctl) from [<c0282c90>] (vfs_ioctl+0x20/0x34)
[ 1514.338165] [<c0282c90>] (vfs_ioctl) from [<c0283654>] (do_vfs_ioctl+0x82c/0x93c)
[ 1514.346038] [<c0283654>] (do_vfs_ioctl) from [<c02837b0>] (SyS_ioctl+0x4c/0x74)
[ 1514.353759] [<c02837b0>] (SyS_ioctl) from [<c0107040>] (ret_fast_syscall+0x0/0x1c)
[ 1514.361755] Code: e3822103 e3822080 e1822781 e5981014 (e5832030)
[ 1514.510833] ---[ end trace dfb3e53c657f34a0 ]---
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Andrey found a way to trigger the WARN_ON_ONCE(delta < len) in
skb_try_coalesce() using syzkaller and a filter attached to a TCP
socket.
As we did recently in commit 158f323b9868 ("net: adjust skb->truesize in
pskb_expand_head()") we can adjust skb->truesize from ___pskb_trim(),
via a call to skb_condense().
If all frags were freed, then skb->truesize can be recomputed.
This call can be done if skb is not yet owned, or destructor is
sock_edemux().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Andrey found a way to trigger the WARN_ON_ONCE(delta < len) in
skb_try_coalesce() using syzkaller and a filter attached to a TCP
socket over loopback interface.
I believe one issue with looped skbs is that tcp_trim_head() can end up
producing skb with under estimated truesize.
It hardly matters for normal conditions, since packets sent over
loopback are never truncated.
Bytes trimmed from skb->head should not change skb truesize, since
skb->head is not reallocated.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On slave list updates, the bonding driver computes its hard_header_len
as the maximum of all enslaved devices's hard_header_len.
If the slave list is empty, e.g. on last enslaved device removal,
ETH_HLEN is used.
Since the bonding header_ops are set only when the first enslaved
device is attached, the above can lead to header_ops->create()
being called with the wrong skb headroom in place.
If bond0 is configured on top of ipoib devices, with the
following commands:
ifup bond0
for slave in $BOND_SLAVES_LIST; do
ip link set dev $slave nomaster
done
ping -c 1 <ip on bond0 subnet>
we will obtain a skb_under_panic() with a similar call trace:
skb_push+0x3d/0x40
push_pseudo_header+0x17/0x30 [ib_ipoib]
ipoib_hard_header+0x4e/0x80 [ib_ipoib]
arp_create+0x12f/0x220
arp_send_dst.part.19+0x28/0x50
arp_solicit+0x115/0x290
neigh_probe+0x4d/0x70
__neigh_event_send+0xa7/0x230
neigh_resolve_output+0x12e/0x1c0
ip_finish_output2+0x14b/0x390
ip_finish_output+0x136/0x1e0
ip_output+0x76/0xe0
ip_local_out+0x35/0x40
ip_send_skb+0x19/0x40
ip_push_pending_frames+0x33/0x40
raw_sendmsg+0x7d3/0xb50
inet_sendmsg+0x31/0xb0
sock_sendmsg+0x38/0x50
SYSC_sendto+0x102/0x190
SyS_sendto+0xe/0x10
do_syscall_64+0x67/0x180
entry_SYSCALL64_slow_path+0x25/0x25
This change addresses the issue avoiding updating the bonding device
hard_header_len when the slaves list become empty, forbidding to
shrink it below the value used by header_ops->create().
The bug is there since commit 54ef31371407 ("[PATCH] bonding: Handle large
hard_header_len") but the panic can be triggered only since
commit fc791b633515 ("IB/ipoib: move back IB LL address into the hard
header").
Reported-by: Norbert P <noe@physik.uzh.ch>
Fixes: 54ef31371407 ("[PATCH] bonding: Handle large hard_header_len")
Fixes: fc791b633515 ("IB/ipoib: move back IB LL address into the hard header")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Upper layer GRO handlers can not handle IP fragments, so
exit GRO processing in this case.
This fixes ESP GRO because the packet must be reassembled
before we can decapsulate, otherwise we get authentication
failures.
It also aligns IPv4 to IPv6 where packets with fragmentation
headers are not passed to upper layer GRO handlers.
Fixes: 7785bba299a8 ("esp: Add a software GRO codepath")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tony Lindgren reports a kernel oops that resulted from my compile-time
fix on the default config. This shows two problems:
a) configurations that did not already enable PTP_1588_CLOCK will
now miss the cpts driver
b) when cpts support is disabled, the driver crashes. This is a
preexisting problem that we did not notice before my patch.
While the second problem is still being investigated, this modifies
the dependencies again, getting us back to the original state, with
another 'select NET_PTP_CLASSIFY' added in to avoid the original
link error we got, and the 'depends on POSIX_TIMERS' to hide
the CPTS support when turning it on would be useless.
Cc: stable@vger.kernel.org # 4.11 needs this
Fixes: 07fef3623407 ("cpsw/netcp: cpts depends on posix_timers")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2017-04-28
1) Do garbage collecting after a policy flush to remove old
bundles immediately. From Xin Long.
2) Fix GRO if netfilter is not defined.
From Sabrina Dubroca.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fix from Dmitry Torokhov:
"Yet another quirk to i8042 to get touchpad recognized on some laptops"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - add Clevo P650RS to the i8042 reset list
|
|
When the base driver is enabled but all SoC specific drivers are turned
off, we now get a build error after code was added to always refer to the
clk gates:
drivers/clk/built-in.o: In function `ccu_pll_notifier_cb':
:(.text+0x154f8): undefined reference to `ccu_gate_helper_disable'
:(.text+0x15504): undefined reference to `ccu_gate_helper_enable'
This changes the Kconfig to always require the gate code to be built-in
when CONFIG_SUNXI_CCU is set.
Fixes: 02ae2bc6febd ("clk: sunxi-ng: Add clk notifier to gate then ungate PLL clocks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fix from Chris Mason:
"We have one more fix for btrfs.
This gets rid of a new WARN_ON from rc1 that ended up making more
noise than we really want. The larger fix for the underflow got
delayed a bit and it's better for now to put it under
CONFIG_BTRFS_DEBUG"
* 'for-linus-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: qgroup: move noisy underflow warning to debugging build
|
|
Parthasarathy Bhuvaragan says:
====================
tipc: fix hanging socket connections
This patch series contains fixes for the socket layer to
prevent hanging / stale connections.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a socket is shutting down, we notify the peer node about the
connection termination by reusing an incoming message if possible.
If the last received message was a connection acknowledgment
message, we reverse this message and set the error code to
TIPC_ERR_NO_PORT and send it to peer.
In tipc_sk_proto_rcv(), we never check for message errors while
processing the connection acknowledgment or probe messages. Thus
this message performs the usual flow control accounting and leaves
the session hanging.
In this commit, we terminate the connection when we receive such
error messages.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, the checks for sockets in CONNECTING state was based on
the assumption that the incoming message was always from the
peer's accepted data socket.
However an application using a non-blocking socket sends an implicit
connect, this socket which is in CONNECTING state can receive error
messages from the peer's listening socket. As we discard these
messages, the application socket hangs as there due to inactivity.
In addition to this, there are other places where we process errors
but do not notify the user.
In this commit, we process such incoming error messages and notify
our users about them using sk_state_change().
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In filter_connect, we use waitqueue_active() to check for any
connections to wakeup. But waitqueue_active() is missing memory
barriers while accessing the critical sections, leading to
inconsistent results.
In this commit, we replace this with an SMP safe wq_has_sleeper()
using the generic socket callback sk_data_ready().
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull nfsd fixes from Bruce Fields:
"Thanks to Ari Kauppi and Tuomas Haanpää at Synopsis for spotting bugs
in our NFSv2/v3 xdr code that could crash the server or leak memory"
* tag 'nfsd-4.11-3' of git://linux-nfs.org/~bfields/linux:
nfsd: stricter decoding of write-like NFSv2/v3 ops
nfsd4: minor NFSv2/v3 write decoding cleanup
nfsd: check for oversized NFSv2/v3 arguments
|
|
Pull ceph fix from Ilya Dryomov:
"A fix for a kernel stack overflow bug in ceph setattr code, marked for
stable"
* tag 'ceph-for-4.11-rc9' of git://github.com/ceph/ceph-client:
ceph: fix recursion between ceph_set_acl() and __ceph_setattr()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
- fix orangefs handling of faults on write() - I'd missed that one back
when orangefs was going through review.
- readdir counterpart of "9p: cope with bogus responses from server in
p9_client_{read,write}" - server might be lying or broken, and we'd
better not overrun the kmalloc'ed buffer we are copying the results
into.
- NFS O_DIRECT read/write can leave iov_iter advanced by too much;
that's what had been causing iov_iter_pipe() warnings davej had been
seeing.
- statx_timestamp.tv_nsec type fix (s32 -> u32). That one really should
go in before 4.11.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
uapi: change the type of struct statx_timestamp.tv_nsec to unsigned
fix nfs O_DIRECT advancing iov_iter too much
p9_client_readdir() fix
orangefs_bufmap_copy_from_iovec(): fix EFAULT handling
|
|
The change in commit 1e2f82d1e9d1 ("statx: Kill fd-with-NULL-path
support in favour of AT_EMPTY_PATH") to error on a NULL pathname to
statx() is inconsistent.
It results in the error EINVAL for a NULL pathname. Other system calls
with similar APIs (fchownat(), fstatat(), linkat()), return EFAULT.
The solution is simply to remove the EINVAL check. As I already pointed
out in [1], user_path_at*() and filename_lookup() will handle the NULL
pathname as per the other APIs, to correctly produce the error EFAULT.
[1] https://lkml.org/lkml/2017/4/26/561
Signed-off-by: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In xfrm_input() when called from GRO, async == 0, and we end up
skipping the processing in xfrm4_transport_finish(). GRO path will
always skip the NF_HOOK, so we don't need the special-case for
!NETFILTER during GRO processing.
Fixes: 7785bba299a8 ("esp: Add a software GRO codepath")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
irq_time_read() returns the irqtime minus the ksoftirqd time. This
is necessary because irq_time_read() is used to substract the IRQ time
from the sum_exec_runtime of a task. If we were to include the softirq
time of ksoftirqd, this task would substract its own CPU time everytime
it updates ksoftirqd->sum_exec_runtime which would therefore never
progress.
But this behaviour got broken by:
a499a5a14db ("sched/cputime: Increment kcpustat directly on irqtime account")
... which now includes ksoftirqd softirq time in the time returned by
irq_time_read().
This has resulted in wrong ksoftirqd cputime reported to userspace
through /proc/stat and thus "top" not showing ksoftirqd when it should
after intense networking load.
ksoftirqd->stime happens to be correct but it gets scaled down by
sum_exec_runtime through task_cputime_adjusted().
To fix this, just account the strict IRQ time in a separate counter and
use it to report the IRQ time.
Reported-and-tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Link: http://lkml.kernel.org/r/1493129448-5356-1-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The comment asserting that the value of struct statx_timestamp.tv_nsec
must be negative when statx_timestamp.tv_sec is negative, is wrong, as
could be seen from the following example:
#define _FILE_OFFSET_BITS 64
#include <assert.h>
#include <fcntl.h>
#include <stdio.h>
#include <sys/stat.h>
#include <unistd.h>
#include <asm/unistd.h>
#include <linux/stat.h>
int main(void)
{
static const struct timespec ts[2] = {
{ .tv_nsec = UTIME_OMIT },
{ .tv_sec = -2, .tv_nsec = 42 }
};
assert(utimensat(AT_FDCWD, ".", ts, 0) == 0);
struct stat st;
assert(stat(".", &st) == 0);
printf("st_mtim.tv_sec = %lld, st_mtim.tv_nsec = %lu\n",
(long long) st.st_mtim.tv_sec,
(unsigned long) st.st_mtim.tv_nsec);
struct statx stx;
assert(syscall(__NR_statx, AT_FDCWD, ".", 0, 0, &stx) == 0);
printf("stx_mtime.tv_sec = %lld, stx_mtime.tv_nsec = %lu\n",
(long long) stx.stx_mtime.tv_sec,
(unsigned long) stx.stx_mtime.tv_nsec);
return 0;
}
It expectedly prints:
st_mtim.tv_sec = -2, st_mtim.tv_nsec = 42
stx_mtime.tv_sec = -2, stx_mtime.tv_nsec = 42
The more generic comment asserting that the value of struct
statx_timestamp.tv_nsec might be negative is confusing to say the least.
It contradicts both the struct stat.st_[acm]time_nsec tradition and
struct timespec.tv_nsec requirements in utimensat syscall.
If statx syscall ever returns a stx_[acm]time containing a negative
tv_nsec that cannot be passed unmodified to utimensat syscall,
it will cause an immense confusion.
Fix this source of confusion by changing the type of struct
statx_timestamp.tv_nsec from __s32 to __u32.
Fixes: a528d35e8bfc ("statx: Add a system call to make enhanced file info available")
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-api@vger.kernel.org
cc: mtk.manpages@gmail.com
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Pull sparc fixes from David Miller:
"I didn't want the release to go out without the statx system call
properly hooked up"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: Update syscall tables.
sparc64: Fill in rest of HAVE_REGS_AND_STACK_ACCESS_API
|
|
With the new statx() syscall, the following both allow the attributes of
the file attached to a file descriptor to be retrieved:
statx(dfd, NULL, 0, ...);
and:
statx(dfd, "", AT_EMPTY_PATH, ...);
Change the code to reject the first option, though this means copying
the path and engaging pathwalk for the fstat() equivalent. dfd can be a
non-directory provided path is "".
[ The timing of this isn't wonderful, but applying this now before we
have statx() in any released kernel, before anybody starts using the
NULL special case. - Linus ]
Fixes: a528d35e8bfc ("statx: Add a system call to make enhanced file info available")
Reported-by: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Eric Sandeen <sandeen@sandeen.net>
cc: fstests@vger.kernel.org
cc: linux-api@vger.kernel.org
cc: linux-man@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull networking fixes from David Miller:
1) MLX5 bug fixes from Saeed Mahameed et al:
- released wrong resources when firmware timeout happens
- fix wrong check for encapsulation size limits
- UAR memory leak
- ETHTOOL_GRXCLSRLALL failed to fill in info->data
2) Don't cache l3mdev on mis-matches local route, causes net devices to
leak refs. From Robert Shearman.
3) Handle fragmented SKBs properly in macsec driver, the problem is
that we were mis-sizing the sgvec table. From Jason A. Donenfeld.
4) We cannot have checksum offload enabled for inner UDP tunneled
packet during IPSEC, from Ansis Atteka.
5) Fix double SKB free in ravb driver, from Dan Carpenter.
6) Fix CPU port handling in b53 DSA driver, from Florian Dainelli.
7) Don't use on-stack buffers for usb_control_msg() in CAN usb driver,
from Maksim Salau.
8) Fix device leak in macvlan driver, from Herbert Xu. We have to purge
the broadcast queue properly on port destroy.
9) Fix tx ring entry limit on EF10 devices in sfc driver. From Bert
Kenward.
10) Fix memory leaks in team driver, from Pan Bian.
11) Don't setup ipv6_stub before it can be actually used, from Paolo
Abeni.
12) Fix tipc socket flow control accounting, from Parthasarathy
Bhuvaragan.
13) Fix crash on module unload in hso driver, from Andreas Kemnade.
14) Fix purging of bridge multicast entries, the problem is that if we
don't defer it to ndo_uninit it's possible for new entries to get
added after we purge. Fix from Xin Long.
15) Don't return garbage for PACKET_HDRLEN getsockopt, from Alexander
Potapenko.
16) Fix autoneg stall properly in PHY layer, and revert micrel driver
change that was papering over it. From Alexander Kochetkov.
17) Don't dereference an ipv4 route as an ipv6 one in the ip6_tunnnel
code, from Cong Wang.
18) Clear out the congestion control private of the TCP socket in all of
the right places, from Wei Wang.
19) rawv6_ioctl measures SKB length incorrectly, fix from Jamie
Bainbridge.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
ipv6: check raw payload size correctly in ioctl
tcp: memset ca_priv data to 0 properly
ipv6: check skb->protocol before lookup for nexthop
net: core: Prevent from dereferencing null pointer when releasing SKB
macsec: dynamically allocate space for sglist
Revert "phy: micrel: Disable auto negotiation on startup"
net: phy: fix auto-negotiation stall due to unavailable interrupt
net/packet: check length in getsockopt() called with PACKET_HDRLEN
net: ipv6: regenerate host route if moved to gc list
bridge: move bridge multicast cleanup to ndo_uninit
ipv6: fix source routing
qed: Fix error in the dcbx app meta data initialization.
netvsc: fix calculation of available send sections
net: hso: fix module unloading
tipc: fix socket flow control accounting error at tipc_recv_stream
tipc: fix socket flow control accounting error at tipc_send_stream
ipv6: move stub initialization after ipv6 setup completion
team: fix memory leaks
sfc: tx ring can only have 2048 entries for all EF10 NICs
macvlan: Fix device ref leak when purging bc_queue
...
|
