| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Print IRQ number used by PCIe Link Bandwidth Notification (Dongdong
Liu)
- Add schedule point in pci_read_config() to reduce max latency
(Jiang Biao)
- Add Kconfig options for MPS/MRRS strategy (Jim Quinlan)
Resource management:
- Fix pci_iounmap() memory leak when !CONFIG_GENERIC_IOMAP (Lorenzo
Pieralisi)
PCIe native device hotplug:
- Reduce noisiness on hot removal (Lukas Wunner)
Power management:
- Revert "PCI/PM: Apply D2 delay as milliseconds, not microseconds"
that was done on the basis of spec typo (Bjorn Helgaas)
- Rename pci_dev.d3_delay to d3hot_delay to remove D3hot/D3cold
ambiguity (Krzysztof Wilczyński)
- Remove unused pcibios_pm_ops (Vaibhav Gupta)
IOMMU:
- Enable Translation Blocking for external devices to harden against
DMA attacks (Rajat Jain)
Error handling:
- Add an ACPI APEI notifier chain for vendor CPER records to enable
device-specific error handling (Shiju Jose)
ASPM:
- Remove struct aspm_register_info to simplify code (Saheed O.
Bolarinwa)
Amlogic Meson PCIe controller driver:
- Build as module by default (Kevin Hilman)
Ampere Altra PCIe controller driver:
- Add MCFG quirk to work around non-standard ECAM implementation
(Tuan Phan)
Broadcom iProc PCIe controller driver:
- Set affinity mask on MSI interrupts (Mark Tomlinson)
Broadcom STB PCIe controller driver:
- Make PCIE_BRCMSTB depend on ARCH_BRCMSTB (Jim Quinlan)
- Add DT bindings for more Brcmstb chips (Jim Quinlan)
- Add bcm7278 register info (Jim Quinlan)
- Add bcm7278 PERST# support (Jim Quinlan)
- Add suspend and resume pm_ops (Jim Quinlan)
- Add control of rescal reset (Jim Quinlan)
- Set additional internal memory DMA viewport sizes (Jim Quinlan)
- Accommodate MSI for older chips (Jim Quinlan)
- Set bus max burst size by chip type (Jim Quinlan)
- Add support for bcm7211, bcm7216, bcm7445, bcm7278 (Jim Quinlan)
Freescale i.MX6 PCIe controller driver:
- Use dev_err_probe() to reduce redundant messages (Anson Huang)
Freescale Layerscape PCIe controller driver:
- Enforce 4K DMA buffer alignment in endpoint test (Hou Zhiqiang)
- Add DT compatible strings for ls1088a, ls2088a (Xiaowei Bao)
- Add endpoint support for ls1088a, ls2088a (Xiaowei Bao)
- Add endpoint test support for lS1088a (Xiaowei Bao)
- Add MSI-X support for ls1088a (Xiaowei Bao)
HiSilicon HIP PCIe controller driver:
- Handle HIP-specific errors via ACPI APEI (Yicong Yang)
HiSilicon Kirin PCIe controller driver:
- Return -EPROBE_DEFER if the GPIO isn't ready (Bean Huo)
Intel VMD host bridge driver:
- Factor out physical offset, bus offset, IRQ domain, IRQ allocation
(Jon Derrick)
- Use generic PCI PM correctly (Jon Derrick)
Marvell Aardvark PCIe controller driver:
- Fix compilation on s390 (Pali Rohár)
- Implement driver 'remove' function and allow to build it as module
(Pali Rohár)
- Move PCIe reset card code to advk_pcie_train_link() (Pali Rohár)
- Convert mvebu a3700 internal SMCC firmware return codes to errno
(Pali Rohár)
- Fix initialization with old Marvell's Arm Trusted Firmware (Pali
Rohár)
Microsoft Hyper-V host bridge driver:
- Fix hibernation in case interrupts are not re-created (Dexuan Cui)
NVIDIA Tegra PCIe controller driver:
- Stop checking return value of debugfs_create() functions (Greg
Kroah-Hartman)
- Convert to use DEFINE_SEQ_ATTRIBUTE macro (Liu Shixin)
Qualcomm PCIe controller driver:
- Reset PCIe to work around Qsdk U-Boot issue (Ansuel Smith)
Renesas R-Car PCIe controller driver:
- Add DT documentation for r8a774a1, r8a774b1, r8a774e1 endpoints
(Lad Prabhakar)
- Add RZ/G2M, RZ/G2N, RZ/G2H IDs to endpoint test (Lad Prabhakar)
- Add DT support for r8a7742 (Lad Prabhakar)
Socionext UniPhier Pro5 controller driver:
- Add DT descriptions of iATU register (host and endpoint) (Kunihiko
Hayashi)
Synopsys DesignWare PCIe controller driver:
- Add link up check in dw_child_pcie_ops.map_bus() (racy, but seems
unavoidable) (Hou Zhiqiang)
- Fix endpoint Header Type check so multi-function devices work (Hou
Zhiqiang)
- Skip PCIE_MSI_INTR0* programming if MSI is disabled (Jisheng Zhang)
- Stop leaking MSI page in suspend/resume (Jisheng Zhang)
- Add common iATU register support instead of keystone-specific code
(Kunihiko Hayashi)
- Major config space access and other cleanups in dwc core and
drivers that use it (al, exynos, histb, imx6, intel-gw, keystone,
kirin, meson, qcom, tegra) (Rob Herring)
- Add multiple PFs support for endpoint (Xiaowei Bao)
- Add MSI-X doorbell mode in endpoint mode (Xiaowei Bao)
Miscellaneous:
- Use fallthrough pseudo-keyword (Gustavo A. R. Silva)
- Fix "0 used as NULL pointer" warnings (Gustavo Pimentel)
- Fix "cast truncates bits from constant value" warnings (Gustavo
Pimentel)
- Remove redundant zeroing for sg_init_table() (Julia Lawall)
- Use scnprintf(), not snprintf(), in sysfs "show" functions
(Krzysztof Wilczyński)
- Remove unused assignments (Krzysztof Wilczyński)
- Fix "0 used as NULL pointer" warning (Krzysztof Wilczyński)
- Simplify bool comparisons (Krzysztof Wilczyński)
- Use for_each_child_of_node() and for_each_node_by_name() (Qinglang
Miao)
- Simplify return expressions (Qinglang Miao)"
* tag 'pci-v5.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (147 commits)
PCI: vmd: Update VMD PM to correctly use generic PCI PM
PCI: vmd: Create IRQ allocation helper
PCI: vmd: Create IRQ Domain configuration helper
PCI: vmd: Create bus offset configuration helper
PCI: vmd: Create physical offset helper
PCI: v3-semi: Remove unneeded break
PCI: dwc: Add link up check in dw_child_pcie_ops.map_bus()
PCI/ASPM: Remove struct pcie_link_state.l1ss
PCI/ASPM: Remove struct aspm_register_info.l1ss_cap
PCI/ASPM: Pass L1SS Capabilities value, not struct aspm_register_info
PCI/ASPM: Remove struct aspm_register_info.l1ss_ctl1
PCI/ASPM: Remove struct aspm_register_info.l1ss_ctl2 (unused)
PCI/ASPM: Remove struct aspm_register_info.l1ss_cap_ptr
PCI/ASPM: Remove struct aspm_register_info.latency_encoding
PCI/ASPM: Remove struct aspm_register_info.enabled
PCI/ASPM: Remove struct aspm_register_info.support
PCI/ASPM: Use 'parent' and 'child' for readability
PCI/ASPM: Move LTR path check to where it's used
PCI/ASPM: Move pci_clear_and_set_dword() earlier
PCI: dwc: Fix MSI page leakage in suspend/resume
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 updates from Ted Ts'o:
"The siginificant new ext4 feature this time around is Harshad's new
fast_commit mode.
In addition, thanks to Mauricio for fixing a race where mmap'ed pages
that are being changed in parallel with a data=journal transaction
commit could result in bad checksums in the failure that could cause
journal replays to fail.
Also notable is Ritesh's buffered write optimization which can result
in significant improvements on parallel write workloads. (The kernel
test robot reported a 330.6% improvement on fio.write_iops on a 96
core system using DAX)
Besides that, we have the usual miscellaneous cleanups and bug fixes"
Link: https://lore.kernel.org/r/20200925071217.GO28663@shao2-debian
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (46 commits)
ext4: fix invalid inode checksum
ext4: add fast commit stats in procfs
ext4: add a mount opt to forcefully turn fast commits on
ext4: fast commit recovery path
jbd2: fast commit recovery path
ext4: main fast-commit commit path
jbd2: add fast commit machinery
ext4 / jbd2: add fast commit initialization
ext4: add fast_commit feature and handling for extended mount options
doc: update ext4 and journalling docs to include fast commit feature
ext4: Detect already used quota file early
jbd2: avoid transaction reuse after reformatting
ext4: use the normal helper to get the actual inode
ext4: fix bs < ps issue reported with dioread_nolock mount opt
ext4: data=journal: write-protect pages on j_submit_inode_data_buffers()
ext4: data=journal: fixes for ext4_page_mkwrite()
jbd2, ext4, ocfs2: introduce/use journal callbacks j_submit|finish_inode_data_buffers()
jbd2: introduce/export functions jbd2_journal_submit|finish_inode_data_buffers()
ext4: introduce ext4_sb_bread_unmovable() to replace sb_bread_unmovable()
ext4: use ext4_sb_bread() instead of sb_bread()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull initial set_fs() removal from Al Viro:
"Christoph's set_fs base series + fixups"
* 'work.set_fs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: Allow a NULL pos pointer to __kernel_read
fs: Allow a NULL pos pointer to __kernel_write
powerpc: remove address space overrides using set_fs()
powerpc: use non-set_fs based maccess routines
x86: remove address space overrides using set_fs()
x86: make TASK_SIZE_MAX usable from assembly code
x86: move PAGE_OFFSET, TASK_SIZE & friends to page_{32,64}_types.h
lkdtm: remove set_fs-based tests
test_bitmap: remove user bitmap tests
uaccess: add infrastructure for kernel builds with set_fs()
fs: don't allow splice read/write without explicit ops
fs: don't allow kernel reads and writes without iter ops
sysctl: Convert to iter interfaces
proc: add a read_iter method to proc proc_ops
proc: cleanup the compat vs no compat file ops
proc: remove a level of indentation in proc_get_inode
|
|
Pull nfsd updates from Bruce Fields:
"The one new feature this time, from Anna Schumaker, is READ_PLUS,
which has the same arguments as READ but allows the server to return
an array of data and hole extents.
Otherwise it's a lot of cleanup and bugfixes"
* tag 'nfsd-5.10' of git://linux-nfs.org/~bfields/linux: (43 commits)
NFSv4.2: Fix NFS4ERR_STALE error when doing inter server copy
SUNRPC: fix copying of multiple pages in gss_read_proxy_verf()
sunrpc: raise kernel RPC channel buffer size
svcrdma: fix bounce buffers for unaligned offsets and multiple pages
nfsd: remove unneeded break
net/sunrpc: Fix return value for sysctl sunrpc.transports
NFSD: Encode a full READ_PLUS reply
NFSD: Return both a hole and a data segment
NFSD: Add READ_PLUS hole segment encoding
NFSD: Add READ_PLUS data support
NFSD: Hoist status code encoding into XDR encoder functions
NFSD: Map nfserr_wrongsec outside of nfsd_dispatch
NFSD: Remove the RETURN_STATUS() macro
NFSD: Call NFSv2 encoders on error returns
NFSD: Fix .pc_release method for NFSv2
NFSD: Remove vestigial typedefs
NFSD: Refactor nfsd_dispatch() error paths
NFSD: Clean up nfsd_dispatch() variables
NFSD: Clean up stale comments in nfsd_dispatch()
NFSD: Clean up switch statement in nfsd_dispatch()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linkinjeon/exfat
Pull exfat updates from Namjae Jeon:
- Replace memcpy with structure assignment
- Remove unneeded codes and use helper function i_blocksize()
- Fix typos found by codespell
* tag 'exfat-for-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/linkinjeon/exfat:
exfat: remove useless check in exfat_move_file()
exfat: remove 'rwoffset' in exfat_inode_info
exfat: replace memcpy with structure assignment
exfat: remove useless directory scan in exfat_add_entry()
exfat: eliminate dead code in exfat_find()
exfat: use i_blocksize() to get blocksize
exfat: fix misspellings using codespell tool
|
|
Pull 9p updates from Dominique Martinet:
"A couple of small fixes (loff_t overflow on 32bit, syzbot
uninitialized variable warning) and code cleanup (xen)"
* tag '9p-for-5.10-rc1' of git://github.com/martinetd/linux:
net: 9p: initialize sun_server.sun_path to have addr's value only when addr is valid
9p/xen: Fix format argument warning
9P: Cast to loff_t before multiplying
|
|
During the stability test, there are some errors:
ext4_lookup:1590: inode #6967: comm fsstress: iget: checksum invalid.
If the inode->i_iblocks too big and doesn't set huge file flag, checksum
will not be recalculated when update the inode information to it's buffer.
If other inode marks the buffer dirty, then the inconsistent inode will
be flushed to disk.
Fix this problem by checking i_blocks in advance.
Cc: stable@kernel.org
Signed-off-by: Luo Meng <luomeng12@huawei.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Link: https://lore.kernel.org/r/20201020013631.3796673-1-luomeng12@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
This commit adds a file in procfs that tracks fast commit related
statistics.
root@kvm-xfstests:/mnt# cat /proc/fs/ext4/vdc/fc_info
fc stats:
7772 commits
15 ineligible
4083 numblks
2242us avg_commit_time
Ineligible reasons:
"Extended attributes changed": 0
"Cross rename": 0
"Journal flag changed": 0
"Insufficient memory": 0
"Swap boot": 0
"Resize": 0
"Dir renamed": 0
"Falloc range op": 0
"FC Commit Failed": 15
Signed-off-by: Harshad Shirwadkar <harshadshirwadkar@gmail.com>
Link: https://lore.kernel.org/r/20201015203802.3597742-10-harshadshirwadkar@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
This is a debug only mount option that forcefully turns fast commits
on at mount time.
Signed-off-by: Harshad Shirwadkar <harshadshirwadkar@gmail.com>
Link: https://lore.kernel.org/r/20201015203802.3597742-9-harshadshirwadkar@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
This patch adds fast commit recovery path support for Ext4 file
system. We add several helper functions that are similar in spirit to
e2fsprogs journal recovery path handlers. Example of such functions
include - a simple block allocator, idempotent block bitmap update
function etc. Using these routines and the fast commit log in the fast
commit area, the recovery path (ext4_fc_replay()) performs fast commit
log recovery.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Harshad Shirwadkar <harshadshirwadkar@gmail.com>
Link: https://lore.kernel.org/r/20201015203802.3597742-8-harshadshirwadkar@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
This patch adds fast commit recovery support in JBD2.
Signed-off-by: Harshad Shirwadkar <harshadshirwadkar@gmail.com>
Link: https://lore.kernel.org/r/20201015203802.3597742-7-harshadshirwadkar@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
This patch adds main fast commit commit path handlers. The overall
patch can be divided into two inter-related parts:
(A) Metadata updates tracking
This part consists of helper functions to track changes that need
to be committed during a commit operation. These updates are
maintained by Ext4 in different in-memory queues. Following are
the APIs and their short description that are implemented in this
patch:
- ext4_fc_track_link/unlink/creat() - Track unlink. link and creat
operations
- ext4_fc_track_range() - Track changed logical block offsets
inodes
- ext4_fc_track_inode() - Track inodes
- ext4_fc_mark_ineligible() - Mark file system fast commit
ineligible()
- ext4_fc_start_update() / ext4_fc_stop_update() /
ext4_fc_start_ineligible() / ext4_fc_stop_ineligible() These
functions are useful for co-ordinating inode updates with
commits.
(B) Main commit Path
This part consists of functions to convert updates tracked in
in-memory data structures into on-disk commits. Function
ext4_fc_commit() is the main entry point to commit path.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Harshad Shirwadkar <harshadshirwadkar@gmail.com>
Link: https://lore.kernel.org/r/20201015203802.3597742-6-harshadshirwadkar@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
This functions adds necessary APIs needed in JBD2 layer for fast
commits.
Signed-off-by: Harshad Shirwadkar <harshadshirwadkar@gmail.com>
Link: https://lore.kernel.org/r/20201015203802.3597742-5-harshadshirwadkar@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
This patch adds fast commit area trackers in the journal_t
structure. These are initialized via the jbd2_fc_init() routine that
this patch adds. This patch also adds ext4/fast_commit.c and
ext4/fast_commit.h files for fast commit code that will be added in
subsequent patches in this series.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Harshad Shirwadkar <harshadshirwadkar@gmail.com>
Link: https://lore.kernel.org/r/20201015203802.3597742-4-harshadshirwadkar@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
We are running out of mount option bits. Add handling for using
s_mount_opt2. Add ext4 and jbd2 fast commit feature flag and also add
ability to turn off the fast commit feature in Ext4.
Signed-off-by: Harshad Shirwadkar <harshadshirwadkar@gmail.com>
Link: https://lore.kernel.org/r/20201015203802.3597742-3-harshadshirwadkar@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
This patch adds necessary documentation for fast commits.
Signed-off-by: Harshad Shirwadkar <harshadshirwadkar@gmail.com>
Link: https://lore.kernel.org/r/20201015203802.3597742-2-harshadshirwadkar@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
In exfat_move_file(), the identity of source and target directory has been
checked by the caller.
Also, it gets stream.start_clu from file dir-entry, which is an invalid
determination.
Signed-off-by: Tetsuhiro Kohada <kohada.t2@gmail.com>
Acked-by: Sungjong Seo <sj1557.seo@samsung.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
|
|
Remove 'rwoffset' in exfat_inode_info and replace it with the parameter of
exfat_readdir().
Since rwoffset is referenced only by exfat_readdir(), it is not necessary
a exfat_inode_info's member.
Also, change cpos to point to the next of entry-set, and return the index
of dir-entry via dir_entry->entry.
Signed-off-by: Tetsuhiro Kohada <kohada.t2@gmail.com>
Acked-by: Sungjong Seo <sj1557.seo@samsung.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
|
|
Use structure assignment instead of memcpy.
Signed-off-by: Tetsuhiro Kohada <kohada.t2@gmail.com>
Acked-by: Sungjong Seo <sj1557.seo@samsung.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
|
|
There is nothing in directory just created, so there is no need to scan.
Signed-off-by: Tetsuhiro Kohada <kohada.t2@gmail.com>
Acked-by: Sungjong Seo <sj1557.seo@samsung.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
|
|
The exfat_find_dir_entry() called by exfat_find() doesn't return -EEXIST.
Therefore, the root-dir information setting is never executed.
Signed-off-by: Tetsuhiro Kohada <kohada.t2@gmail.com>
Acked-by: Sungjong Seo <sj1557.seo@samsung.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
|
|
We alreday has the interface i_blocksize() to get blocksize,
so use it.
Signed-off-by: Xianting Tian <tian.xianting@h3c.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
|
|
Sedat reported typos using codespell tool.
$ codespell fs/exfat/*.c | grep -v iput
fs/exfat/namei.c:293: upto ==> up to
fs/exfat/nls.c:14: tabel ==> table
$ codespell fs/exfat/*.h
fs/exfat/exfat_fs.h:133: usally ==> usually
Fix typos found by codespell.
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
|
|
git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- Add Toshiba Visconti watchdog driver
- it87_wdt: add IT8772 + IT8784
- several fixes and improvements
* tag 'linux-watchdog-5.10-rc1' of git://www.linux-watchdog.org/linux-watchdog:
watchdog: Add Toshiba Visconti watchdog driver
watchdog: bindings: Add binding documentation for Toshiba Visconti watchdog device
watchdog: it87_wdt: add IT8784 ID
watchdog: sp5100_tco: Enable watchdog on Family 17h devices if disabled
watchdog: sp5100: Fix definition of EFCH_PM_DECODEEN3
watchdog: renesas_wdt: support handover from bootloader
watchdog: imx7ulp: Watchdog should continue running for wait/stop mode
watchdog: rti: Simplify with dev_err_probe()
watchdog: davinci: Simplify with dev_err_probe()
watchdog: cadence: Simplify with dev_err_probe()
watchdog: remove unneeded inclusion of <uapi/linux/sched/types.h>
watchdog: Use put_device on error
watchdog: Fix memleak in watchdog_cdev_register
watchdog: imx7ulp: Strictly follow the sequence for wdog operations
watchdog: it87_wdt: add IT8772 ID
watchdog: pcwd_usb: Avoid GFP_ATOMIC where it is not needed
drivers: watchdog: rdc321x_wdt: Fix race condition bugs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"A new driver this cycle is making the bulk of the changes and the
rx8010 driver has been rework to use the modern APIs.
Summary:
Subsystem:
- new generic DT properties: aux-voltage-chargeable,
trickle-voltage-millivolt
New driver:
- Microcrystal RV-3032
Drivers:
- ds1307: use aux-voltage-chargeable
- r9701, rx8010: modernization of the driver
- rv3028: fix clock output, trickle resistor values, RAM
configuration registers"
* tag 'rtc-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (50 commits)
rtc: r9701: set range
rtc: r9701: convert to devm_rtc_allocate_device
rtc: r9701: stop setting RWKCNT
rtc: r9701: remove useless memset
rtc: r9701: stop setting a default time
rtc: r9701: remove leftover comment
rtc: rv3032: Add a driver for Microcrystal RV-3032
dt-bindings: rtc: rv3032: add RV-3032 bindings
dt-bindings: rtc: add trickle-voltage-millivolt
rtc: rv3028: ensure ram configuration registers are saved
rtc: rv3028: factorize EERD bit handling
rtc: rv3028: fix trickle resistor values
rtc: rv3028: fix clock output support
rtc: mt6397: Remove unused member dev
rtc: rv8803: simplify the return expression of rv8803_nvram_write
rtc: meson: simplify the return expression of meson_vrtc_probe
rtc: rx8010: rename rx8010_init_client() to rx8010_init()
rtc: ds1307: enable rx8130's backup battery, make it chargeable optionally
rtc: ds1307: consider aux-voltage-chargeable
rtc: ds1307: store previous charge default per chip
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
Pull dmi update from Jean Delvare.
* 'dmi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
Replace HTTP links with HTTPS ones: DMI/SMBIOS SUPPORT
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
- if a host can be a client, too, the I2C core can now use it to
emulate SMBus HostNotify support (STM32 and R-Car added this so far)
- also for client mode, a testunit has been added. It can create rare
situations on the bus, so host controllers can be tested
- a binding has been added to mark the bus as "single-master". This
allows for better timeout detections
- new driver for Mellanox Bluefield
- massive refactoring of the Tegra driver
- EEPROMs recognized by the at24 driver can now have custom names
- rest is driver updates
* 'i2c/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (80 commits)
Documentation: i2c: add testunit docs to index
i2c: tegra: Improve driver module description
i2c: tegra: Clean up whitespaces, newlines and indentation
i2c: tegra: Clean up and improve comments
i2c: tegra: Clean up printk messages
i2c: tegra: Clean up variable names
i2c: tegra: Improve formatting of variables
i2c: tegra: Check errors for both positive and negative values
i2c: tegra: Factor out hardware initialization into separate function
i2c: tegra: Factor out register polling into separate function
i2c: tegra: Factor out packet header setup from tegra_i2c_xfer_msg()
i2c: tegra: Factor out error recovery from tegra_i2c_xfer_msg()
i2c: tegra: Rename wait/poll functions
i2c: tegra: Remove "dma" variable from tegra_i2c_xfer_msg()
i2c: tegra: Remove redundant check in tegra_i2c_issue_bus_clear()
i2c: tegra: Remove likely/unlikely from the code
i2c: tegra: Remove outdated barrier()
i2c: tegra: Clean up variable types
i2c: tegra: Reorder location of functions in the code
i2c: tegra: Clean up probe function
...
|
|
Pull ceph updates from Ilya Dryomov:
- a patch that removes crush_workspace_mutex (myself). CRUSH
computations are no longer serialized and can run in parallel.
- a couple new filesystem client metrics for "ceph fs top" command
(Xiubo Li)
- a fix for a very old messenger bug that affected the filesystem,
marked for stable (myself)
- assorted fixups and cleanups throughout the codebase from Jeff and
others.
* tag 'ceph-for-5.10-rc1' of git://github.com/ceph/ceph-client: (27 commits)
libceph: clear con->out_msg on Policy::stateful_server faults
libceph: format ceph_entity_addr nonces as unsigned
libceph: fix ENTITY_NAME format suggestion
libceph: move a dout in queue_con_delay()
ceph: comment cleanups and clarifications
ceph: break up send_cap_msg
ceph: drop separate mdsc argument from __send_cap
ceph: promote to unsigned long long before shifting
ceph: don't SetPageError on readpage errors
ceph: mark ceph_fmt_xattr() as printf-like for better type checking
ceph: fold ceph_update_writeable_page into ceph_write_begin
ceph: fold ceph_sync_writepages into writepage_nounlock
ceph: fold ceph_sync_readpages into ceph_readpage
ceph: don't call ceph_update_writeable_page from page_mkwrite
ceph: break out writeback of incompatible snap context to separate function
ceph: add a note explaining session reject error string
libceph: switch to the new "osd blocklist add" command
libceph, rbd, ceph: "blacklist" -> "blocklist"
ceph: have ceph_writepages_start call pagevec_lookup_range_tag
ceph: use kill_anon_super helper
...
|
|
- Remove leftover bridge initialization (Lorenzo Pieralisi)
* remotes/lorenzo/pci/xilinx:
PCI: xilinx-cpm: Remove leftover bridge initialization
|
|
- Remove unused assignment (Krzysztof Wilczyński)
* remotes/lorenzo/pci/xgene:
PCI: xgene: Remove unused assignment to variable msi_val
|
|
- Add physical offset helper (Jon Derrick)
- Add bus offset configuration helper (Jon Derrick)
- Add IRQ domain configuration helper (Jon Derrick)
- Add IRQ allocation helper (Jon Derrick)
- Drop pci_save_state()/pci_restore_state() in favor of the PCI core PM
(Jon Derrick)
* pci/vmd:
PCI: vmd: Update VMD PM to correctly use generic PCI PM
PCI: vmd: Create IRQ allocation helper
PCI: vmd: Create IRQ Domain configuration helper
PCI: vmd: Create bus offset configuration helper
PCI: vmd: Create physical offset helper
|
|
- Drop return value checking for debugfs_create() calls (Greg
Kroah-Hartman)
- Convert debugfs "ports" file to use DEFINE_SEQ_ATTRIBUTE() (Liu Shixin)
* remotes/lorenzo/pci/tegra:
PCI: tegra: Convert to use DEFINE_SEQ_ATTRIBUTE macro
PCI: tegra: No need to check return value of debugfs_create() functions
|
|
- Document R8A774A1, R8A774B1, R8A774E1 endpoint support in DT (Lad
Prabhakar)
- Add R8A774A1, R8A774B1, R8A774E1 (RZ/G2M, RZ/G2N, RZ/G2H) IDs to endpoint
test (Lad Prabhakar)
- Add device tree support for R8A7742 (Lad Prabhakar)
- Use "fallthrough" pseudo-keyword (Gustavo A. R. Silva)
* remotes/lorenzo/pci/rcar:
dt-bindings: PCI: rcar: Add device tree support for r8a7742
PCI: rcar-gen2: Use fallthrough pseudo-keyword
misc: pci_endpoint_test: Add Device ID for RZ/G2H PCIe controller
dt-bindings: pci: rcar-pci-ep: Document r8a774e1
misc: pci_endpoint_test: Add Device ID for RZ/G2M and RZ/G2N PCIe controllers
dt-bindings: pci: rcar-pci-ep: Document r8a774a1 and r8a774b1
|
|
- Make sure PCIe is reset before init to work around QSDK U-Boot issue
(Ansuel Smith)
- Set iproc affinity mask on MSI interrupts (Mark Tomlinson)
* remotes/lorenzo/pci/qcom:
PCI: qcom: Make sure PCIe is reset before init for rev 2.1.0
|
|
- Remove useless msi_controller pointer allocation (Lorenzo Pieralisi)
* remotes/lorenzo/pci/mvebu:
PCI: mvebu: Remove useless msi_controller pointer allocation
|
|
- Simplify mobiveil_pcie_init_irq_domain() (Liu Shixin)
* remotes/lorenzo/pci/mobiveil:
PCI: mobiveil: Simplify mobiveil_pcie_init_irq_domain() return expression
|
|
- Add pci-meson module support and enable by default on ARCH_MESON (Kevin
Hilman)
* remotes/lorenzo/pci/meson:
PCI: meson: Build as module by default
|
|
* remotes/lorenzo/pci/loongson:
PCI: loongson: Simplify loongson_pci_probe() return expression
|
|
- Return -EPROBE_DEFER in case the gpio isn't ready (Bean Huo)
* remotes/lorenzo/pci/kirin:
PCI: kirin: Return -EPROBE_DEFER in case the gpio isn't ready
|
|
- Set affinity mask on MSI interrupts (Mark Tomlinson)
- Simplify by using module_bcma_driver (Liu Shixin)
- Fix 'using integer as NULL pointer' warning (Krzysztof Wilczyński)
* remotes/lorenzo/pci/iproc:
PCI: iproc: Fix using plain integer as NULL pointer in iproc_pcie_pltfm_probe
PCI: iproc: Use module_bcma_driver to simplify the code
PCI: iproc: Set affinity mask on MSI interrupts
|
|
- Use "fallthrough" pseudo-keyword (Gustavo A. R. Silva)
- Drop redundant error messages after devm_clk_get() (Anson Huang)
* remotes/lorenzo/pci/imx6:
PCI: imx6: Do not output error message when devm_clk_get() failed with -EPROBE_DEFER
PCI: imx6: Use fallthrough pseudo-keyword
|
|
- Fix hibernation in case interrupts are not re-created (Dexuan Cui)
* remotes/lorenzo/pci/hv:
PCI: hv: Fix hibernation in case interrupts are not re-created
|
|
- Fix designware-ep Header Type check (Hou Zhiqiang)
- Use DBI accessors instead of own config accessors (Rob Herring)
- Allow overriding bridge pci_ops (Rob Herring)
- Allow root and child buses to have different pci_ops (Rob Herring)
- Add default dwc pci_ops.map_bus (Rob Herring)
- Use pci_ops for root config space accessors in al, exynos, histb,
keystone, kirin, meson, tegra (Rob Herring)
- Remove dwc own/other config accessor ops (Rob Herring)
- Use generic config accessors in dwc (Rob Herring)
- Also call .add_bus() callback for root bus (Rob Herring)
- Convert keystone .scan_bus() callback to use pci_ops.add_bus (Rob
Herring)
- Convert dwc to use pci_host_probe() (Rob Herring)
- Remove dwc root_bus pointer (Rob Herring)
- Remove storing of PCI resources in dwc-specific structs (Rob Herring)
- Simplify config space handling (Rob Herring)
- Drop keystone duplicated DT num-viewport handling (Rob Herring)
- Check CONFIG_PCI_MSI in dw_pcie_msi_init() instead of duplicating it in
all the drivers (Rob Herring)
- Remove imx6 duplicate PCIE_LINK_WIDTH_SPEED_CONTROL definition (Rob
Herring)
- Add dwc num_lanes for use when it's lacking from DT (Rob Herring)
- Ensure "Fast Link Mode" simulation environment setting is cleared (Rob
Herring)
- Drop meson duplicate number of lanes setup (Rob Herring)
- Drop meson unnecessary RC config space init (Rob Herring)
- Rework meson config and dwc port logic register accesses (Rob Herring)
- Use common PCI register definitions in imx6 and qcom (Rob Herring)
- Search for DesignWare PCIe Capability instead of hard-coding its location
(Rob Herring)
- Use common DesignWare register definitions in tegra (Rob Herring)
- Drop keystone unused DBI2 code (Rob Herring)
- Make dwc ATU accessors private (Rob Herring)
- Centralize link gen setting in dwc (Rob Herring)
- Set PORT_LINK_DLL_LINK_EN in common dwc setup code (Rob Herring)
- Drop intel-gw unnecessary DT 'device_type' checking (Rob Herring)
- Move intel-gw PCI_CAP_ID_EXP discovery to the single place it's used (Rob
Herring)
- Drop intel-gw unused max_width (Rob Herring)
- Move N_FTS (fast training sequence) setup to common dwc setup (Rob
Herring)
- Convert spear13xx, tegra194 to use DBI accessors (Rob Herring)
- Add multiple PFs support for DWC (Xiaowei Bao)
- Add MSI-X doorbell mode for endpoint mode (Xiaowei Bao)
- Update MSI/MSI-X capability management for endpoints (Xiaowei Bao)
- Add layerscape ls1088a and ls2088a compatible strings (Xiaowei Bao)
- Update layerscape MSI/MSI-X management (Xiaowei Bao)
- Use doorbell to support MSI-X on layerscape (Xiaowei Bao)
- Add layerscape endpoint mode support for ls1088a and ls2088a (Xiaowei
Bao)
- Add layerscape ls1088a node to DT (Xiaowei Bao)
- Add Freescale/Layerscape ls1088a to endpoint test (Xiaowei Bao)
- Add endpoint test driver data for Layerscape PCIe controllers (Hou
Zhiqiang)
- Fix 'cast truncates bits from constant value' warning (Gustavo Pimentel)
- Add uniphier iATU register description (Kunihiko Hayashi)
- Add common iATU register support (Kunihiko Hayashi)
- Remove keystone iATU register mapping in favor of generic dwc support
(Kunihiko Hayashi)
- Skip PCIE_MSI_INTR0* programming if MSI is disabled (Jisheng Zhang)
- Fix MSI page leakage in suspend/resume (Jisheng Zhang)
- Check whether link is up before attempting config access (best-effort fix
even though it's racy) (Hou Zhiqiang)
* remotes/lorenzo/pci/dwc:
PCI: dwc: Add link up check in dw_child_pcie_ops.map_bus()
PCI: dwc: Fix MSI page leakage in suspend/resume
PCI: dwc: Skip PCIE_MSI_INTR0* programming if MSI is disabled
PCI: keystone: Remove iATU register mapping
PCI: dwc: Add common iATU register support
dt-bindings: PCI: uniphier-ep: Add iATU register description
dt-bindings: PCI: uniphier: Add iATU register description
PCI: dwc: Fix 'cast truncates bits from constant value'
misc: pci_endpoint_test: Add driver data for Layerscape PCIe controllers
misc: pci_endpoint_test: Add LS1088a in pci_device_id table
PCI: layerscape: Add EP mode support for ls1088a and ls2088a
PCI: layerscape: Modify the MSIX to the doorbell mode
PCI: layerscape: Modify the way of getting capability with different PEX
PCI: layerscape: Fix some format issue of the code
dt-bindings: pci: layerscape-pci: Add compatible strings for ls1088a and ls2088a
PCI: designware-ep: Modify MSI and MSIX CAP way of finding
PCI: designware-ep: Move the function of getting MSI capability forward
PCI: designware-ep: Add the doorbell mode of MSI-X in EP mode
PCI: designware-ep: Add multiple PFs support for DWC
PCI: dwc: Use DBI accessors
PCI: dwc: Move N_FTS setup to common setup
PCI: dwc/intel-gw: Drop unused max_width
PCI: dwc/intel-gw: Move getting PCI_CAP_ID_EXP offset to intel_pcie_link_setup()
PCI: dwc/intel-gw: Drop unnecessary checking of DT 'device_type' property
PCI: dwc: Set PORT_LINK_DLL_LINK_EN in common setup code
PCI: dwc: Centralize link gen setting
PCI: dwc: Make ATU accessors private
PCI: dwc: Remove read_dbi2 code
PCI: dwc/tegra: Use common Designware port logic register definitions
PCI: dwc: Remove hardcoded PCI_CAP_ID_EXP offset
PCI: dwc/qcom: Use common PCI register definitions
PCI: dwc/imx6: Use common PCI register definitions
PCI: dwc/meson: Rework PCI config and DW port logic register accesses
PCI: dwc/meson: Drop unnecessary RC config space initialization
PCI: dwc/meson: Drop the duplicate number of lanes setup
PCI: dwc: Ensure FAST_LINK_MODE is cleared
PCI: dwc: Add a 'num_lanes' field to struct dw_pcie
PCI: dwc/imx6: Remove duplicate define PCIE_LINK_WIDTH_SPEED_CONTROL
PCI: dwc: Check CONFIG_PCI_MSI inside dw_pcie_msi_init()
PCI: dwc/keystone: Drop duplicated 'num-viewport'
PCI: dwc: Simplify config space handling
PCI: dwc: Remove storing of PCI resources
PCI: dwc: Remove root_bus pointer
PCI: dwc: Convert to use pci_host_probe()
PCI: dwc: keystone: Convert .scan_bus() callback to use add_bus
PCI: Also call .add_bus() callback for root bus
PCI: dwc: Use generic config accessors
PCI: dwc: Remove dwc specific config accessor ops
PCI: dwc: histb: Use pci_ops for root config space accessors
PCI: dwc: exynos: Use pci_ops for root config space accessors
PCI: dwc: kirin: Use pci_ops for root config space accessors
PCI: dwc: meson: Use pci_ops for root config space accessors
PCI: dwc: tegra: Use pci_ops for root config space accessors
PCI: dwc: keystone: Use pci_ops for config space accessors
PCI: dwc: al: Use pci_ops for child config space accessors
PCI: dwc: Add a default pci_ops.map_bus for root port
PCI: dwc: Allow overriding bridge pci_ops
PCI: dwc: Use DBI accessors instead of own config accessors
PCI: Allow root and child buses to have different pci_ops
PCI: designware-ep: Fix the Header Type check
|
|
- Remove obsolete path from comment (Flavio Suligoi)
- Simplify cdns_pcie_host_init_address_translation() (Qinglang Miao)
* remotes/lorenzo/pci/cadence:
PCI: cadence: Simplify cdns_pcie_host_init_address_translation() return expression
PCI: cadence-ep: Remove obsolete path from comment
|
|
- Make PCIE_BRCMSTB depend on and default to ARCH_BRCMSTB (Jim Quinlan)
- Add DT bindings for 7278, 7216, 7211, and new properties (Jim Quinlan)
- Add bcm7278 register info (Jim Quinlan)
- Add suspend and resume pm_ops (Jim Quinlan)
- Add bcm7278 PERST# support (Jim Quinlan)
- Add control of RESCAL reset (Jim Quinlan)
- Set additional internal memory DMA viewport sizes (Jim Quinlan)
- Accommodate MSI for older chips (Jim Quinlan)
- Set bus max burst size by chip type (Jim Quinlan)
- Add bcm7211, bcm7216, bcm7445, bcm7278 to match list (Jim Quinlan)
* remotes/lorenzo/pci/brcmstb:
PCI: brcmstb: Add bcm7211, bcm7216, bcm7445, bcm7278 to match list
PCI: brcmstb: Set bus max burst size by chip type
PCI: brcmstb: Accommodate MSI for older chips
PCI: brcmstb: Set additional internal memory DMA viewport sizes
PCI: brcmstb: Add control of rescal reset
PCI: brcmstb: Add bcm7278 PERST# support
PCI: brcmstb: Add suspend and resume pm_ops
PCI: brcmstb: Add bcm7278 register info
dt-bindings: PCI: Add bindings for more Brcmstb chips
PCI: brcmstb: PCIE_BRCMSTB depends on ARCH_BRCMSTB
|
|
- Fix s390 build error (Pali Rohár)
- Check for errors from pci_bridge_emul_init() (Pali Rohár)
- Export pci-bridge-emul functions for use by modules (Pali Rohár)
- Make aardvark driver modular (Pali Rohár)
- Move PCIe reset code to advk_pcie_train_link() (Pali Rohár)
- Convert internal SMCC firmware return codes to errno (Pali Rohár)
- Fix initialization with old Marvell's Arm Trusted Firmware (Pali Rohár)
* remotes/lorenzo/pci/aardvark:
PCI: aardvark: Fix initialization with old Marvell's Arm Trusted Firmware
phy: marvell: comphy: Convert internal SMCC firmware return codes to errno
PCI: aardvark: Move PCIe reset card code to advk_pcie_train_link()
PCI: aardvark: Implement driver 'remove' function and allow to build it as module
PCI: pci-bridge-emul: Export API functions
PCI: aardvark: Check for errors from pci_bridge_emul_init() call
PCI: aardvark: Fix compilation on s390
|
|
- Remove unused msi_ctrl, io_optional and align_resource fields from ARM
struct hw_pci (Lorenzo Pieralisi)
* remotes/lorenzo/pci/arm:
ARM/PCI: Remove unused fields from struct hw_pci
|
|
- Remove useless __KERNEL__ preprocessor guard in sparc io_32.h (Lorenzo
Pieralisi)
- Move ioremap/iounmap declaration so it's visible in asm-generic/io.h
(Lorenzo Pieralisi)
- Fix memory leak in generic !CONFIG_GENERIC_IOMAP pci_iounmap()
implementation (Lorenzo Pieralisi)
* remotes/lorenzo/pci/pci-iomap:
asm-generic/io.h: Fix !CONFIG_GENERIC_IOMAP pci_iounmap() implementation
sparc32: Move ioremap/iounmap declaration before asm-generic/io.h include
sparc32: Remove useless io_32.h __KERNEL__ preprocessor guard
|
|
- Add ACPI APEI notifier chain for unknown (vendor) CPER records (Shiju
Jose)
- Add handling of HiSilicon HIP PCIe controller errors (Yicong Yang)
* remotes/lorenzo/pci/apei:
PCI: hip: Add handling of HiSilicon HIP PCIe controller errors
ACPI / APEI: Add a notifier chain for unknown (vendor) CPER records
|
|
- Remove unnecessary #includes (Gustavo Pimentel)
- Fix intel_mid_pci.c build error when !CONFIG_ACPI (Randy Dunlap)
- Use scnprintf(), not snprintf(), in sysfs "show" functions (Krzysztof
Wilczyński)
- Simplify pci-pf-stub by using module_pci_driver() (Liu Shixin)
- Print IRQ used by Link Bandwidth Notification (Dongdong Liu)
- Update sysfs mmap-related #ifdef comments (Clint Sbisa)
- Simplify pci_dev_reset_slot_function() (Lukas Wunner)
- Use "NULL" instead of "0" to fix sparse warnings (Gustavo Pimentel)
- Simplify bool comparisons (Krzysztof Wilczyński)
- Drop double zeroing for P2PDMA sg_init_table() (Julia Lawall)
* pci/misc:
PCI: v3-semi: Remove unneeded break
PCI/P2PDMA: Drop double zeroing for sg_init_table()
PCI: Simplify bool comparisons
PCI: endpoint: Use "NULL" instead of "0" as a NULL pointer
PCI: Simplify pci_dev_reset_slot_function()
PCI: Update mmap-related #ifdef comments
PCI/LINK: Print IRQ number used by port
PCI/IOV: Simplify pci-pf-stub with module_pci_driver()
PCI: Use scnprintf(), not snprintf(), in sysfs "show" functions
x86/PCI: Fix intel_mid_pci.c build error when ACPI is not enabled
PCI: Remove unnecessary header includes
|
