| Age | Commit message (Collapse) | Author |
|---|
|
On EF10, MC_CMD_VPORT_RECONFIGURE can cause a CODE_MC_REBOOT event
to be sent to a function without incrementing the (adapter-wide)
warm_boot_count. In this case, the reboot is not detected by the
loop on efx_mcdi_poll_reboot(), so prepare for recovery from an MC
reboot anyway. When this codepath is run, the MC has always just
rebooted, so this recovery is valid.
The loop on efx_mcdi_poll_reboot() is still required for other MC
reboot cases, so that actions in response to an MC reboot are
performed, such as clearing locally calculated statistics.
Siena NICs are unaffected by this change as the above scenario
does not apply.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Scott Feldman says:
====================
switchdev: push bridge ageing_time attribute down
Push bridge-level attributes down to switchdev drivers. This patchset
adds the infrastructure and then pushes, as an example, ageing_time attribute
down from bridge to switchdev (rocker) driver. Add some range-checking
for ageing_time.
RTNETLINK answers: Numerical result out of range
Up until now, switchdev attrs where port-level attrs, so the netdev used in
switchdev_attr_set() would be a switch port or bond of switch ports. With
bridge-level attrs, the netdev passed to switchdev_attr_set() is the bridge
netdev. The same recusive algo is used to visit the leaves of the stacked
drivers to set the attr, it's just in this case we start one layer higher in
the stack. One note is not all ports in the bridge may support setting a
bridge-level attribute, so rather than failing the entire set, we'll skip over
those ports returning -EOPNOTSUPP.
v2->v3: Per Jiri review: push only ageing_time attr down at this time, and
don't pass raw bridge IFLA_BR_* values; rather use new switchdev attr ID for
ageing_time.
v1->v2: rebase w/ net-next
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The FDB cleanup timer will get rescheduled to re-evaluate FDB entries
based on new ageing_time.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use SWITCHDEV_F_SKIP_EOPNOTSUPP to skip over ports in bridge that don't
support setting ageing_time (or setting bridge attrs in general).
If push fails, don't update ageing_time in bridge and return err to user.
If push succeeds, update ageing_time in bridge and run gc_timer now to
recalabrate when to run gc_timer next, based on new ageing_time.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This allows us to recurse over all the ports, skipping over unsupporting
ports. Without the change, the recursion would stop at first unsupported
port.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setting the stage to push bridge-level attributes down to port driver so
hardware can be programmed accordingly. Bridge-level attribute example is
ageing_time. This is a per-bridge attribute, not a per-bridge-port attr.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The alive parameter of tcp_orphan_retries, indicates
whether the connection is assumed alive or not.
In the function and all places calling it is used as a boolean value.
Therefore this changes the type of alive to bool in the function
definition and all calling locations.
Since tcp_orphan_tries is a tcp_timer.c local function no change in
any other file or header is necessary.
Signed-off-by: Richard Sailer <richard@weltraumpflege.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enables adding of fdb entries pointing to the bridge device.
This can be used to propagate mac address of vlan interfaces
configured on top of the vlan filtering bridge.
Before:
$bridge fdb add 44:38:39:00:27:9f dev bridge
RTNETLINK answers: Invalid argument
After:
$bridge fdb add 44:38:39:00:27:9f dev bridge
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before recent TCP listener patches, we were updating listener
sk->sk_rxhash before the cloning of master socket.
children sk_rxhash was therefore correct after the normal 3WHS.
But with lockless listener, we no longer dirty/change listener sk_rxhash
as it would be racy.
We need to correctly update the child sk_rxhash, otherwise first data
packet wont hit correct cpu if RFS is used.
Fixes: 079096f103fa ("tcp/dccp: install syn_recv requests into ehash table")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Willem de Bruijn <willemb@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vivien Didelot says:
====================
net: dsa: push switchdev prepare phase in FDB ops
This patchset pushes the switchdev prepare phase for the FDB add and del
operations down to the DSA drivers. Currently only mv88e6xxx is affected.
Since the dump requires a bit of refactoring in the driver, it'll come in a
future patchset.
Changes in v2:
* forward declare switchdev structs instead of fixing the dsa.h include.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For consistency with the FDB add operation, propagate the
switchdev_obj_port_fdb structure in the DSA drivers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that the prepare phase is pushed down to the DSA drivers, propagate
it to the port_fdb_add function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Push the prepare phase for FDB operations down to the DSA drivers, with
a new port_fdb_prepare function. Currently only mv88e6xxx is affected.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-10-08
Here's another set of Bluetooth & 802.15.4 patches for the 4.4 kernel.
802.15.4:
- Many improvements & fixes to the mrf24j40 driver
- Fixes and cleanups to nl802154, mac802154 & ieee802154 code
Bluetooth:
- New chipset support in btmrvl driver
- Fixes & cleanups to btbcm, btmrvl, bpa10x & btintel drivers
- Support for vendor specific diagnostic data through common API
- Cleanups to the 6lowpan code
- New events & message types for monitor channel
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
we have two processes to do:
P1#: ifconfig eth0 down; which will call bnx2_close, then will
, and set Null to stats_blk
P2#: ifconfig eth0; which will call bnx2_get_stats64, it will
use stats_blk.
In one case:
--P1#-- --P2#--
stats_blk(no null)
bnx2_free_mem
->bp->stats_blk = NULL
GET_64BIT_NET_STATS
then it will cause 'NULL Pointer' Problem.
it is as well with 'ethtool -S ethx'.
Allocate the statistics block at probe time so that this problem is
impossible
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
selinux needs few changes to accommodate fact that SYNACK messages
can be attached to a request socket, lacking sk_security pointer
(Only syncookies are still attached to a TCP_LISTEN socket)
Adds a new sk_listener() helper, and use it in selinux and sch_fq
Fixes: ca6fb0651883 ("tcp: attach SYNACK messages to request sockets instead of listener")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported by: kernel test robot <ying.huang@linux.intel.com>
Cc: Paul Moore <paul@paul-moore.com>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Eric Paris <eparis@parisplace.org>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
t4_check_fw_version() can return several error codes (-EINVAL, -EBUSY,
-EAGAIN). The present code sets the adapter state to UNINIT only if its
an EFAULT. In all the error cases set the adapter to uninitialized state.
In t4_check_fw_version() if call to t4_get_fw_version() fails, repeat the
operation a few times before returning failure.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
eBPF socket filter programs may see junk in 'u32 cb[5]' area,
since it could have been used by protocol layers earlier.
For socket filter programs used in af_packet we need to clean
20 bytes of skb->cb area if it could be used by the program.
For programs attached to TCP/UDP sockets we need to save/restore
these 20 bytes, since it's used by protocol layers.
Remove SK_RUN_FILTER macro, since it's no longer used.
Long term we may move this bpf cb area to per-cpu scratch, but that
requires addition of new 'per-cpu load/store' instructions,
so not suitable as a short term fix.
Fixes: d691f9e8d440 ("bpf: allow programs to write to certain skb fields")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Paul Gortmaker says:
====================
make non-modular code explicitly non-modular
[v2: drop m68k patches that Geert converted to modules; add one ARM
driver patch ; update net-next baseline to today; switch to ARM
for build testing.]
In a previous merge window, we made changes to allow better
delineation between modular and non-modular code in commit
0fd972a7d91d6e15393c449492a04d94c0b89351 ("module: relocate module_init
from init.h to module.h"). This allows us to now ensure module code
looks modular and non-modular code does not accidentally look modular
just to avoid suffering build breakage.
Here we target code that is, by nature of their Makefile and/or
Kconfig settings, only available to be built-in, but implicitly
presenting itself as being possibly modular by way of using modular
headers, macros, and functions.
The goal here is to remove that illusion of modularity from these
files, but in a way that leaves the actual runtime unchanged.
In doing so, we remove code that has never been tested and adds
no value to the tree. And we continue the process of expecting a
level of consistency between the Kconfig/Makefile of code and the
code in use itself.
Fortuntately the net subsystem has relatively few instances, given
the overall amount of code and drivers it contains. For comparison
there are over 300 instances tree wide, resulting in a possible net
removal of on the order of 5000 lines of unused code.
Build tested on net-next from today, on ARM, since that is the arch
where the one ethernet driver changed here is available.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Kconfig currently controlling compilation of this code is:
drivers/net/ethernet/ti/Kconfig:config TI_CPSW_PHY_SEL
drivers/net/ethernet/ti/Kconfig: bool "TI CPSW Switch Phy sel Support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modularity so that when reading the
driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Kconfig currently controlling compilation of this code is:
net/sched/Kconfig:menuconfig NET_SCHED
net/sched/Kconfig: bool "QoS and/or fair queueing"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit. We can
change to one of the other priority initcalls (subsys?) at any later
date, if desired.
We also delete the MODULE_LICENSE tag since all that information
is already contained at the top of the file in the comments.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Kconfig currently controlling compilation of this code is:
net/dcb/Kconfig:config DCB
net/dcb/Kconfig: bool "Data Center Bridging support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit. We can
change to one of the other priority initcalls (subsys?) at any later
date, if desired.
We also delete the MODULE_LICENSE tag etc. since all that information
is (or is now) already contained at the top of the file in the comments.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Anish Bhatt <anish@chelsio.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Shani Michaeli <shanim@mellanox.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Makefile currently controlling compilation of this code lists
it under "obj-y" ...meaning that it currently is not being built as
a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit. We can
change to one of the other priority initcalls (subsys?) at any later
date, if desired.
We can't remove module.h since the file uses other module related
stuff even though it is not modular itself.
We move the information from the MODULE_LICENSE tag to the top of the
file, since that information is not captured anywhere else. The
MODULE_ALIAS_NET_PF_PROTO becomes a no-op in the non modular case, so
it is removed.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Craig Gallek <kraig@google.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Yaowei Bai says:
====================
net: small improvement
This patchset makes several functions in net return bool to improve
readability and/or simplicity because these functions only use one
or zero as their return value.
No functional changes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch makes lockdep_rtnl_is_held return bool due to this
particular function only using either one or zero as its return
value.
In another patch lockdep_is_held is also made return bool.
No functional change.
Signed-off-by: Yaowei Bai <bywxiaobai@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch makes bad_mask return bool due to this particular function
only using either one or zero as its return value.
No functional change.
Signed-off-by: Yaowei Bai <bywxiaobai@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch makes inet_ifa_match return bool due to this
particular function only using either one or zero as its return
value.
No functional change.
Signed-off-by: Yaowei Bai <bywxiaobai@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch makes dccp_bad_service_code return bool due to these
particular functions only using either one or zero as their return
value.
dccp_list_has_service is also been made return bool in this patchset.
No functional change.
Signed-off-by: Yaowei Bai <bywxiaobai@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch makes dccp_list_has_service return bool due to this
particular function only using either one or zero as its return
value.
No functional change.
Signed-off-by: Yaowei Bai <bywxiaobai@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch makes can_dropped_invalid_skb return bool due to this
particular function only using either one or zero as its return
value.
No functional change.
Signed-off-by: Yaowei Bai <bywxiaobai@163.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch makes lockdep_nfnl_is_held return bool to improve
readability due to this particular function only using either
one or zero as its return value.
No functional change.
Signed-off-by: Yaowei Bai <bywxiaobai@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch makes ieee80211_is_* return bool to improve
readability due to these particular functions only using either
one or zero as their return value.
No functional change.
Signed-off-by: Yaowei Bai <bywxiaobai@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch makes lockdep_genl_is_held return bool to improve
readability due to this particular function only using either
one or zero as its return value.
No functional change.
Signed-off-by: Yaowei Bai <bywxiaobai@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Or Gerlitz says:
==============================
Mellanox driver update for net-next
Some small fixes and small enhancements from the team.
Series applies over net-next commit acb4a6b "tcp: ensure prior synack rtx behavior
with small backlogs".
==============================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 'for' loop when undoing rb-tree insertions and list-adds in the
error flow in add_res_range had errors, fix them.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The procedure mlx4_update_qp leaks mailboxes in its error-flow, fix that.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Changed the receive control flow in a way that steering
rules are added only when the RSS object is already in RTR/RTS mode.
Some optimization features, which are enabled by the device firmware,
require this condition in order to be effective.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use a single threaded work queue for each device in the system instead of
using one thread for any device. This is required so we can concurrently
process system error handling for all the devices that need that.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use ioread function to read health buffer data. In addition, print the
firmware version as a string for readability and also use dev_err to have
the device string to be printed.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation to handling system errors at the mlx5_core level, change the
interface of cmd_work_handler to accept a 64 bit argument for the vector.
This allows to encode a flag that signifies when the handler is called
as a result of a driver logic that wishes to terminate commands that
the hardware may not be able to terminate. Such command completions
are detected at the handler and proper return status is encoded.
To be able to terminate page handler commands, we make sure to set
the corresponding bit in the bitmask.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Improve the messages printed by the mlx5 macros to include the device
string. In addition, prefix names used by the macros with two underscores
to avoid possible name collisions.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-10-08
This series contains updates to i40e and i40evf only (again).
Jesse fixes an issue where the driver was issuing a WARN_ON during ring
size changes because the code was cloning the rx_ring struct but not
zeroing out the pointers before allocating new memory, so simply zero
out the pointers. Also reduced the function call overhead by moving
the interrupt enable function by moving it to the header file, which it
in turn allows us to inline it. Also does a thorough job of code
cleanup to fix spaces after declarations, remove unnecessary braces
and breaks, remove another __func__ use and general code tidiness.
Mitch adds mover verbose error messages when the number of supported VFs
is reported in driver init and it different from the number reported in
config space. Updated the VF driver to now detect a reset with the
VF_ARQLEN register since the enable bit is cleared when the VF is reset
and it stays cleared until the VF driver processes the reset and
re-enables the admin queue which is more reliable than using the
VFGEN_RSTAT as previously.
Neerav adds parsing for CEE DCBx TLVs from the LLDP MIB since there is
a need to get the CEE DesiredCfg Tx by firmware and DCB configuration
Rx from peer for debug and other application purposes.
Carolyn fixes a problem where the PF's Flow Director filter table would
have an entry that the hardware was unable to add, when this occurs an
invalid entry gets replayed and a valid one is lost.
Matt fixes an issue where multiple link up messages can be logged
resulting from admin queue link status timing when link properties are
changed.
Shannon adds the ability to control the period link polling through
ethtool to be able to switch it off and on for debugging link issues.
Serey explicitly assigns the enum index for each VSI type so that the PF
and VF always reference to the same VSI type event if the enum lists
are different.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To help users and developers know what compile options
and hardware features are enabled at compile time, print
VxLAN is available.
Change-ID: I3162f3b7678dc725a597f964217920eb218b480b
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The VF really doesn't care about the QOS handle but it will in the
future. Since the VF only uses TC0, send it that handle. On the VF
side, save the handle and use it to populate the QOS params when we call
into the client interface.
Change-ID: I76f41b070baeaa09b19383e9168bc677837e0761
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Use the capabilities passed to us by the PF driver to control VF driver
behavior. In the process, clean up the VLAN add/remove code so it's not
a horrible morass of ifdefs.
Change-ID: I1050eaf12b658a26fea6813047c9964163c70a73
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
I found a code indent that was avoidable because a whole function is inside
an if block, reverse the if and move the code back a tab.
Change-ID: I9989c8750ee61678fbf96a3b0fd7bf7cc7ef300a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add missings spaces after declarations, remove another __func__ use,
remove uncessary braces, remove unneeded breaks, and useless returns,
and generally fix up some code.
Change-ID: Ie715d6b64976c50e1c21531685fe0a2bd38c4244
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Using VFGEN_RSTAT to detect a VF reset is an endeavor that is fraught
with peril. It's entirely too easy to miss a reset because none of the
bits are sticky. By the time the VF driver reads the register, the reset
may have been processed and cleaned up by the PF driver, leaving the
register in the same state that it was before the reset.
Instead, detect a reset with the VF_ARQLEN register. When the VF is
reset, the enable bit in this register is cleared, and it stays cleared
until the VF driver processes the reset and re-enables the admin queue.
Because we now deal with multiple registers in the reset and watchdog
tasks, rename the rstat_val variable to reg_val.
Change-ID: Id1df17045c0992e607da0162d31807f7fc20d199
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Changes parsing of AQ command Get CEE DCBX OPER CFG (0x0A07). Change is
required because FW creates the oper_prio_tc nibbles reversed from those
in the CEE Priority Group sub-TLV.
Change-ID: I7d9d8641bb430d30e286fc3fac909866ef8a0de8
Signed-off-by: Greg Bowers <gregory.j.bowers@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
