| Age | Commit message (Collapse) | Author |
|---|
|
The documentation for Armada 8040 says:
Bit 2 Field InBandAnEn In-band Auto-Negotiation enable. ...
When <PortType> = 1 (1000BASE-X) this field must be set to 1.
We presently ignore whether userspace requests autonegotiation or not
through the ethtool ksettings interface. However, we have some network
interfaces that wish to do this. To offer a consistent API across
network interfaces, deny the ability to disable autonegotiation on
mvpp2 hardware when in 1000BASE-X and 2500BASE-X.
This means the only way to switch between 2500BASE-X and 1000BASE-X
on SFPs that support this will be:
# ethtool -s ethX advertise 0x20000006000 # 1000BASE-X Pause AsymPause
# ethtool -s ethX advertise 0xe000 # 2500BASE-X Pause AsymPause
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Marek Behún <kabel@kernel.org>
Acked-by: Marcin Wojtas <mw@semihalf.com>
|
|
The documentation for Armada 38x says:
Bit 2 Field InBandAnEn In-band Auto-Negotiation enable. ...
When <PortType> = 1 (1000BASE-X) this field must be set to 1.
We presently ignore whether userspace requests autonegotiation or not
through the ethtool ksettings interface. However, we have some network
interfaces that wish to do this. To offer a consistent API across
network interfaces, deny the ability to disable autonegotiation on
mvneta hardware when in 1000BASE-X and 2500BASE-X.
This means the only way to switch between 2500BASE-X and 1000BASE-X
on SFPs that support this will be:
# ethtool -s ethX advertise 0x20000002000 # 1000BASE-X Pause
# ethtool -s ethX advertise 0xa000 # 2500BASE-X Pause
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Marek Behún <kabel@kernel.org>
|
|
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Split out the code handling the GMAC from the rest of the driver. This
block appears to be shared amongst several revisions of the IP.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
An initial stab at converting mvneta to PCS operations. There's a few
FIXMEs to be solved.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Move the 1ms clock control out of mac_config() into mac_prepare() and
mac_finish(), which simplifies the mac_config() code.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Convert mvneta to use the mac_prepare() and mac_finish() methods in
preparation to converting mvneta to split-PCS support.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Program the 1ms autonegotiation clock divisor according to the clocking
rate of neta - without this, the 1ms clock ticks at about 660us on
Armada 38x configured for 250MHz. Bring this into correct specification.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Further augmentation of the comphy setup.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The implementation appears not to support pause modes on anything
but RGMII, RGMII_TXID, MII and REVMII interface modes. Let phylink
know that detail.
(This may not be correct; particularly see the FIXMEs in this patch.)
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Use the phy interface mode bitmaps for SFP modules and PHYs to select
the operating interface for SFPs and PHYs with SFPs.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add a supported_interfaces member to phylib so we know which
interfaces a PHY supports. Currently, set any unconverted driver
to indicate all interfaces are supported.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Select the host interface configuration according to the capabilities
of the host; this allows the kernel to support SFP modules using the
88x3310.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Pass the supported PHY interface types to phylib so that PHY drivers
can select an appropriate host configuration mode for their interface
according to the host capabilities.
This is only done for SFP modules presently.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Display SFP module information verbosely, splitting the generic parts
into a separate file.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add a compatible for SFP+ cages. SFP+ cages are backwards compatible,
but the ethernet device behind them may not support the slower speeds
of SFP modules.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Cooled SFP+ transceivers need a longer initialisation (startup) time.
Select the initialisation time depending on the cooled option bit.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
phy_error() is called from phy_interrupt() or phy_state_machine(), and
uses WARN_ON() to print a backtrace. The backtrace is not useful when
reporting a PHY error.
However, a system may contain multiple ethernet PHYs, and phy_error()
gives no clue which one caused the problem.
Replace WARN_ON() with a call to phydev_err() so that we can see which
PHY had an error, and also inform the user that we are halting the PHY.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Allow the PHY to probe when there is no firmware, but do not allow the
link to come up by forcing the PHY state to PHY_HALTED in a similar way
to phy_error().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Provide phy driver start/stop hooks so that the PHY driver knows when
the network driver is starting or stopping. This will be used for the
Marvell 10G driver so that we can sanely refuse to start if the PHYs
firmware is not present, and also so that we can sanely support SFPs
behind the PHY.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Support reporting the hardware resolved pause enablement states via
phylib, overriding our software implementation.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Allow phylib drivers to pass the hardware-resolved pause state to MAC
drivers, rather than using the software-based pause resolution code.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Configure the Macchiatobin 10G PHY LED modes to correct their polarity.
We keep the existing LED behaviours, but switch their polarity to
reflect how they are connected. Tweak the LED modes as well to be:
left: off = no link
solid green = RJ45 link up (not SFP+ cage)
flash green = traffic
right: off = no link
solid green = 10G
solid yellow = 1G
flash green = 100M
flash yellow = 10M
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add support for configuring the LEDs. Macchiatobin has an oddity in
that the left LED goes out when the cable is connected, and flashes
when there's link activity. This is because the reset default for
the LED outputs assume that the LED is connected to supply, not to
ground. Add support for configuring the LED modes and polarities.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add a DT bindings document for the Marvell 10G driver, which will
augment the generic ethernet PHY binding by having LED mode
configuration.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
There are several places which open code comparing PHY IDs. Provide a
couple of helpers to assist with this, using a slightly simpler test
than the original:
- phy_id_compare() compares two arbitary PHY IDs and a mask of the
significant bits in the ID.
- phydev_id_compare() compares the bound phydev with the specified
PHY ID, using the bound driver's mask.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The at803x driver contains a function, at803x_match_phy_id(), which
tests whether the PHY ID matches the value passed, comparing phy_id
with phydev->phy_id and testing all bits that have a "one" in the
mask, phydev->drv->phy_id_mask.
This is the same test that is used to match the driver, with phy_id
replaced with the driver specified ID, phydev->drv->phy_id.
Hence, we already know the value of the bits being tested if we look
at phydev->drv->phy_id directly, and we do not require a complicated
test to check them. Test directly against phydev->drv->phy_id instead.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The SGMII PCS PHY needs to be updated with the link configuration in
the mac_link_up() call rather than in mac_config(). However,
mtk_sgmii_setup_mode_force() programs the SGMII block during
mac_config() when using 802.3z interface modes with the link
configuration.
Split that functionality from mtk_sgmii_setup_mode_force(), moving it
to a new mtk_sgmii_link_up() function, and call it from mac_link_up().
This does not look correct to me: 802.3z modes operate at a fixed
speed. The contents of mtk_sgmii_link_up() look more appropriate for
SGMII mode, but the original code definitely did not call
mtk_sgmii_setup_mode_force() for SGMII mode but only 802.3z mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Implement the .phylink_get_interfaces method for mv88e6xxx driver.
We are currently only interested in SGMII, 1000base-x and 2500base-x
modes (for the SFP code). USXGMII and 10gbase-r can be added later for
Amethyst. XAUI and RXAUI are irrelevant for SFP (but maybe not for
QSFP?).
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add a new DSA switch operation, phylink_get_interfaces, which should
fill in which PHY_INTERFACE_MODE_* are supported by given port.
Use this before phylink_create to fill phylink's config
supported_interfaces member.
This allows for phylink to determine which PHY_INTERFACE_MODE to use
with SFP modules.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Fill in the phy interface mode bitmap for the Marvell mvpp2 driver, so
phylink can know which interfaces are supported by the MAC.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Fill in the phy interface mode bitmap for the Marvell mvneta driver, so
phylink can know which interfaces are supported by the MAC.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Where a MAC provides the PHY interface mode capabilities, use the PHY
interface mode bitmaps to select the operating interface mode for
optical SFP modules, rather than using the linkmode bitmaps.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add a PHY interface bitmap for the MAC driver to specify which PHY
interfaces are supported to phylink.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
We currently parse the SFP EEPROM to a bitmap of ethtool link modes,
and then attempt to convert the link modes to a PHY interface mode.
While this works at present, there are cases where this is sub-optimal.
For example, where a module can operate with several different PHY
interface modes.
To start addressing this, arrange for the SFP EEPROM parsing to also
provide a bitmap of the possible PHY interface modes.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Add support for a bitmap for phy interface modes, which includes:
- a macro to declare the interface bitmap
- an inline helper to zero the interface bitmap
- an inline helper to detect an empty interface bitmap
- an inline helper to do a bitwise AND operation on two interface
bitmaps
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
We only need to fiddle about with the supported mask after we have
validated the user's requested parameters. Simplify and streamline the
code by moving the linkmode copy and update of the autoneg bit after
validating the user's request.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Augment the phy link debug prints with the pause state.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
The auto-negotiation state in the PCS as set by
phylink_mii_c22_pcs_config was previously always enabled when the
driver is configured for in-band autonegotiation, even if
autonegotiation was disabled on the interface with ethtool. Update the
code to set the BMCR_ANENABLE bit based on the interface's
autonegotiation enabled state.
Update phylink_mii_c22_pcs_get_state to not check
autonegotiation-related fields when autonegotiation is disabled.
Update phylink_mac_pcs_get_state to initialize the state based on the
interface's configured speed, duplex and pause parameters rather than
to unknown when autonegotiation is disabled, before calling the
driver's pcs_get_state functions, as they are not likely to provide
meaningful data for these fields when autonegotiation is disabled. In
this case the driver is really just filling in the link state field.
Note that in cases where there is a downstream PHY connected, such as
with SGMII and a copper PHY, the configuration set by ethtool is
handled by phy_ethtool_ksettings_set and not propagated to the PCS.
This is correct since SGMII or 1000Base-X autonegotiation with the PCS
should normally still be used even if the copper side has disabled it.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Update three drivers to use the new phylink_set_10g_modes() helper:
Cadence macb, Freescale DPAA2 and Marvell PP2.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Add a helper for setting 10Gigabit modes, so we have one central
place that sets all appropriate 10G modes for a driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Phylink documentation says:
Note that the PHY may be able to transform from one connection
technology to another, so, eg, don't clear 1000BaseX just
because the MAC is unable to BaseX mode. This is more about
clearing unsupported speeds and duplex settings. The port modes
should not be cleared; phylink_set_port_modes() will help with this.
So add the missing 10G modes.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Marek Behún <kabel@kernel.org>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com>
|
|
Add support for the downshift tunable for the Marvell 88x3310 PHY.
Downshift is only usable with firmware 0.3.5.0 and later.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Dan Carpenter points out that we have a code path that permits a NULL
netdev pointer to be passed to netif_carrier_off(), which will cause
a kernel oops. In any case, we need to set pl->old_link_state to false
to have the desired effect when there is no netdev present.
Fixes: f97493657c63 ("net: phylink: add suspend/resume support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Joakim Zhang reports that Wake-on-Lan with the stmmac ethernet driver broke
when moving the incorrect handling of mac link state out of mac_config().
This reason this breaks is because the stmmac's WoL is handled by the MAC
rather than the PHY, and phylink doesn't cater for that scenario.
This patch adds the necessary phylink code to handle suspend/resume events
according to whether the MAC still needs a valid link or not. This is the
barest minimum for this support.
Reported-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Tested-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One hotfix for a NULL pointer deref in the Renesas usb clk driver"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: renesas: rcar-usb2-clock-sel: Fix kernel NULL pointer dereference
|
