summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2020-10-10Revert "i2c: imx: Fix reset of I2SR_IAL flag"Wolfram Sang
This reverts commit fa4d30556883f2eaab425b88ba9904865a4d00f3. An updated version was sent. So, revert this version and give the new version more time for testing. Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-10-08i2c: meson: fixup rate calculation with filter delayNicolas Belin
Apparently, 15 cycles of the peripheral clock are used by the controller for sampling and filtering. Because this was not known before, the rate calculation is slightly off. Clean up and fix the calculation taking this filtering delay into account. Fixes: 30021e3707a7 ("i2c: add support for Amlogic Meson I2C controller") Signed-off-by: Nicolas Belin <nbelin@baylibre.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-10-08i2c: meson: keep peripheral clock enabledJerome Brunet
SCL rate appears to be different than what is expected. For example, We get 164kHz on i2c3 of the vim3 when 400kHz is expected. This is partially due to the peripheral clock being disabled when the clock is set. Let's keep the peripheral clock on after probe to fix the problem. This does not affect the SCL output which is still gated when i2c is idle. Fixes: 09af1c2fa490 ("i2c: meson: set clock divider in probe instead of setting it for each transfer") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-10-08i2c: meson: fix clock setting overwriteJerome Brunet
When the slave address is written in do_start(), SLAVE_ADDR is written completely. This may overwrite some setting related to the clock rate or signal filtering. Fix this by writing only the bits related to slave address. To avoid causing unexpected changed, explicitly disable filtering or high/low clock mode which may have been left over by the bootloader. Fixes: 30021e3707a7 ("i2c: add support for Amlogic Meson I2C controller") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-10-08i2c: imx: Fix reset of I2SR_IAL flagChristian Eggers
According to the "VFxxx Controller Reference Manual" (and the comment block starting at line 97), Vybrid requires writing a one for clearing an interrupt flag. Syncing the method for clearing I2SR_IIF in i2c_imx_isr(). Signed-off-by: Christian Eggers <ceggers@arri.de> Fixes: 4b775022f6fd ("i2c: imx: add struct to hold more configurable quirks") Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Cc: stable@vger.kernel.org Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-10-04Linux 5.9-rc8Linus Torvalds
2020-10-03Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvmLinus Torvalds
Pull kvm fixes from Paolo Bonzini: "Two bugfixes" * tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: KVM: VMX: update PFEC_MASK/PFEC_MATCH together with PF intercept KVM: arm64: Restore missing ISB on nVHE __tlb_switch_to_guest
2020-10-03Merge tag 'for-linus-5.9b-rc8-tag' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip Pull xen fix from Juergen Gross: "Fix a regression introduced in 5.9-rc3 which caused a system running as fully virtualized guest under Xen to crash when using legacy devices like a floppy" * tag 'for-linus-5.9b-rc8-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: xen/events: don't use chip_data for legacy IRQs
2020-10-03Merge tag 'usb-5.9-rc8' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB/PHY fixes from Greg KH: "Here are some small USB and PHY driver fixes for 5.9-rc8 The PHY driver fix resolves an issue found by Dan Carpenter for a memory leak. The USB fixes fall into two groups: - usb gadget fix from Bryan that is a fix for a previous security fix that showed up in in-the-wild testing - usb core driver matching bugfixes. This fixes a bug that has plagued the both the usbip driver and syzbot testing tools this -rc release cycle. All is now working properly so usbip connections will work, and syzbot can get back to fuzzing USB drivers properly. All have been in linux-next for a while with no reported issues" * tag 'usb-5.9-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: usbcore/driver: Accommodate usbip usbcore/driver: Fix incorrect downcast usbcore/driver: Fix specific driver selection Revert "usbip: Implement a match function to fix usbip" USB: gadget: f_ncm: Fix NDP16 datagram validation phy: ti: am654: Fix a leak in serdes_am654_probe()
2020-10-03Merge branch 'i2c/for-current' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux Pull i2c fixes from Wolfram Sang: "Some more driver fixes for i2c" * 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: i2c: npcm7xx: Clear LAST bit after a failed transaction. i2c: cpm: Fix i2c_ram structure i2c: i801: Exclude device from suspend direct complete optimization
2020-10-03Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input Pull input fixes from Dmitry Torokhov: "A couple more driver quirks, now enabling newer trackpoints from Synaptics for real" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: i8042 - add nopnp quirk for Acer Aspire 5 A515 Input: trackpoint - enable Synaptics trackpoints
2020-10-03scripts/spelling.txt: fix malformed entryEric Biggers
One of the entries has three fields "mistake||correction||correction" rather than the expected two fields "mistake||correction". Fix it. Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Link: https://lkml.kernel.org/r/20200930234359.255295-1-ebiggers@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-10-03mm/page_alloc: handle a missing case for memalloc_nocma_{save/restore} APIsJoonsoo Kim
memalloc_nocma_{save/restore} APIs can be used to skip page allocation on CMA area, but, there is a missing case and the page on CMA area could be allocated even if APIs are used. This patch handles this case to fix the potential issue. For now, these APIs are used to prevent long-term pinning on the CMA page. When the long-term pinning is requested on the CMA page, it is migrated to the non-CMA page before pinning. This non-CMA page is allocated by using memalloc_nocma_{save/restore} APIs. If APIs doesn't work as intended, the CMA page is allocated and it is pinned for a long time. This long-term pin for the CMA page causes cma_alloc() failure and it could result in wrong behaviour on the device driver who uses the cma_alloc(). Missing case is an allocation from the pcplist. MIGRATE_MOVABLE pcplist could have the pages on CMA area so we need to skip it if ALLOC_CMA isn't specified. Fixes: 8510e69c8efe (mm/page_alloc: fix memalloc_nocma_{save/restore} APIs) Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Vlastimil Babka <vbabka@suse.cz> Acked-by: Michal Hocko <mhocko@suse.com> Cc: "Aneesh Kumar K . V" <aneesh.kumar@linux.ibm.com> Cc: Mel Gorman <mgorman@techsingularity.net> Link: https://lkml.kernel.org/r/1601429472-12599-1-git-send-email-iamjoonsoo.kim@lge.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-10-03mm, slub: restore initial kmem_cache flagsEric Farman
The routine that applies debug flags to the kmem_cache slabs inadvertantly prevents non-debug flags from being applied to those same objects. That is, if slub_debug=<flag>,<slab> is specified, non-debugged slabs will end up having flags of zero, and the slabs may be unusable. Fix this by including the input flags for non-matching slabs with the contents of slub_debug, so that the caches are created as expected alongside any debugging options that may be requested. With this, we can remove the check for a NULL slub_debug_string, since it's covered by the loop itself. Fixes: e17f1dfba37b ("mm, slub: extend slub_debug syntax for multiple blocks") Signed-off-by: Eric Farman <farman@linux.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Kees Cook <keescook@chromium.org> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Link: https://lkml.kernel.org/r/20200930161931.28575-1-farman@linux.ibm.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-10-03Merge tag 'kvmarm-fixes-5.9-3' of ↵Paolo Bonzini
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm-master KVM/arm64 fixes for 5.9, take #3 - Fix synchronization of VTTBR update on TLB invalidation for nVHE systems
2020-10-03KVM: VMX: update PFEC_MASK/PFEC_MATCH together with PF interceptPaolo Bonzini
The PFEC_MASK and PFEC_MATCH fields in the VMCS reverse the meaning of the #PF intercept bit in the exception bitmap when they do not match. This means that, if PFEC_MASK and/or PFEC_MATCH are set, the hypervisor can get a vmexit for #PF exceptions even when the corresponding bit is clear in the exception bitmap. This is unexpected and is promptly detected by a WARN_ON_ONCE. To fix it, reset PFEC_MASK and PFEC_MATCH when the #PF intercept is disabled (as is common with enable_ept && !allow_smaller_maxphyaddr). Reported-by: Qian Cai <cai@redhat.com>> Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org> Tested-by: Naresh Kamboju <naresh.kamboju@linaro.org> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2020-10-02Merge tag 'pinctrl-v5.9-2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control fixes from Linus Walleij: "Some pin control fixes here. All of them are driver fixes, the Intel Cherryview being the most interesting one. - Fix a mux problem for I2C in the MVEBU driver. - Fix a really hairy inversion problem in the Intel Cherryview driver. - Fix the register for the sdc2_clk in the Qualcomm SM8250 driver. - Check the virtual GPIO boot failur in the Mediatek driver" * tag 'pinctrl-v5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: pinctrl: mediatek: check mtk_is_virt_gpio input parameter pinctrl: qcom: sm8250: correct sdc2_clk pinctrl: cherryview: Preserve CHV_PADCTRL1_INVRXTX_TXDATA flag on GPIOs pinctrl: mvebu: Fix i2c sda definition for 98DX3236
2020-10-02Merge tag 'pci-v5.9-fixes-2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull PCI fixes from Bjorn Helgaas: - Fix rockchip regression in rockchip_pcie_valid_device() (Lorenzo Pieralisi) - Add Pali Rohár as aardvark PCI maintainer (Pali Rohár) * tag 'pci-v5.9-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: MAINTAINERS: Add Pali Rohár as aardvark PCI maintainer PCI: rockchip: Fix bus checks in rockchip_pcie_valid_device()
2020-10-02Merge tag 'scsi-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi Pull SCSI fixes from James Bottomley: "Two patches in driver frameworks. The iscsi one corrects a bug induced by a BPF change to network locking and the other is a regression we introduced" * tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: scsi: iscsi: iscsi_tcp: Avoid holding spinlock while calling getpeername() scsi: target: Fix lun lookup for TARGET_SCF_LOOKUP_LUN_FROM_TAG case
2020-10-02Merge tag 'io_uring-5.9-2020-10-02' of git://git.kernel.dk/linux-blockLinus Torvalds
Pull io_uring fixes from Jens Axboe: - fix for async buffered reads if read-ahead is fully disabled (Hao) - double poll match fix - ->show_fdinfo() potential ABBA deadlock complaint fix * tag 'io_uring-5.9-2020-10-02' of git://git.kernel.dk/linux-block: io_uring: fix async buffered reads when readahead is disabled io_uring: fix potential ABBA deadlock in ->show_fdinfo() io_uring: always delete double poll wait entry on match
2020-10-02Merge tag 'block-5.9-2020-10-02' of git://git.kernel.dk/linux-blockLinus Torvalds
Pull block fix from Jens Axboe: "Single fix for a ->commit_rqs failure case" * tag 'block-5.9-2020-10-02' of git://git.kernel.dk/linux-block: blk-mq: call commit_rqs while list empty but error happen
2020-10-02Merge branch 'work.epoll' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs Pull epoll fixes from Al Viro: "Several race fixes in epoll" * 'work.epoll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: ep_create_wakeup_source(): dentry name can change under you... epoll: EPOLL_CTL_ADD: close the race in decision to take fast path epoll: replace ->visited/visited_list with generation count epoll: do not insert into poll queues until all sanity checks are done
2020-10-02Merge tag 'riscv-for-linus-5.9-rc8' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux Pull RISC-V fixes from Palmer Dabbelt: "Two fixes for this week: - The addition of a symbol export for clint_time_val, which has been inlined into some timex functions and can be used by drivers. - A fix to avoid calling get_cycles() before the timers have been probed. These both only effect !MMU systems" * tag 'riscv-for-linus-5.9-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: RISC-V: Check clint_time_val before use clocksource: clint: Export clint_time_val for modules
2020-10-02Merge tag 'for-5.9-rc7-tag' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux Pull btrfs fixes from David Sterba: "Two more fixes. One is for a lockdep warning/lockup (also caught by syzbot), that one has been seen in practice. Regarding the other syzbot reports mentioned last time, they don't seem to be urgent and reliably reproducible so they'll be fixed later. The second fix is for a potential corruption when device replace finishes and the in-memory state of trim is not copied to the new device" * tag 'for-5.9-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux: btrfs: fix filesystem corruption after a device replace btrfs: move btrfs_rm_dev_replace_free_srcdev outside of all locks btrfs: move btrfs_scratch_superblocks into btrfs_dev_replace_finishing
2020-10-02Merge tag 'pm-5.9-rc8' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull power management fixes from Rafael Wysocki: "These fix one more issue related to the recent RCU-lockdep changes, a typo in documentation and add a missing return statement to intel_pstate. Specifics: - Fix up RCU usage for cpuidle on the ARM imx6q platform (Ulf Hansson) - Fix typo in the PM documentation (Yoann Congal) - Add return statement that is missing after recent changes in the intel_pstate driver (Zhang Rui)" * tag 'pm-5.9-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: ARM: imx6q: Fixup RCU usage for cpuidle Documentation: PM: Fix a reStructuredText syntax error cpufreq: intel_pstate: Fix missing return statement
2020-10-02Merge tag 'staging-5.9-rc8' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging Pull IIO fixes from Greg KH: "Here are two small IIO driver fixes for 5.9-rc8 that resolve some reported issues: - driver name fixed in one driver - device name typo fixed Both have been in linux-next for a while with no reported problems" * tag 'staging-5.9-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: iio: adc: qcom-spmi-adc5: fix driver name iio: adc: ad7124: Fix typo in device name
2020-10-02Merge tag 'gpio-v5.9-2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio Pull GPIO fixes from Linus Walleij: "Some late GPIO fixes for the v5.9 series: - Fix compiler warnings on the OMAP when PM is disabled - Clear the interrupt when setting edge sensitivity on the Spreadtrum driver. - Fix up spurious interrupts on the TC35894. - Support threaded interrupts on the Siox controller. - Fix resource leaks on the mockup driver. - Fix line event handling in syscall compatible mode for the character device. - Fix an unitialized variable in the PCA953A driver. - Fix access to all GPIO IRQs on the Aspeed AST2600. - Fix line direction on the AMD FCH driver. - Use the bitmap API instead of compiler intrinsics for bit manipulation in the PCA953x driver" * tag 'gpio-v5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: gpio: pca953x: Correctly initialize registers 6 and 7 for PCA957x gpio: pca953x: Use bitmap API over implicit GCC extension gpio: amd-fch: correct logic of GPIO_LINE_DIRECTION gpio: aspeed: fix ast2600 bank properties gpio/aspeed-sgpio: don't enable all interrupts by default gpio/aspeed-sgpio: enable access to all 80 input & output sgpios gpio: pca953x: Fix uninitialized pending variable gpiolib: Fix line event handling in syscall compatible mode gpio: mockup: fix resource leak in error path gpio: siox: explicitly support only threaded irqs gpio: tc35894: fix up tc35894 interrupt configuration gpio: sprd: Clear interrupt when setting the type as edge gpio: omap: Fix warnings if PM is disabled
2020-10-02Merge tag 'mmc-v5.9-rc4-3' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc Pull MMC fixes from Ulf Hansson: - Fix deadlock when removing MEMSTICK host - Workaround broken CMDQ on Intel GLK based IRBIS models * tag 'mmc-v5.9-rc4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: mmc: sdhci: Workaround broken command queuing on Intel GLK based IRBIS models memstick: Skip allocating card when removing host
2020-10-02random32: Restore __latent_entropy attribute on net_rand_stateThibaut Sautereau
Commit f227e3ec3b5c ("random32: update the net random state on interrupt and activity") broke compilation and was temporarily fixed by Linus in 83bdc7275e62 ("random32: remove net_rand_state from the latent entropy gcc plugin") by entirely moving net_rand_state out of the things handled by the latent_entropy GCC plugin. From what I understand when reading the plugin code, using the __latent_entropy attribute on a declaration was the wrong part and simply keeping the __latent_entropy attribute on the variable definition was the correct fix. Fixes: 83bdc7275e62 ("random32: remove net_rand_state from the latent entropy gcc plugin") Acked-by: Willy Tarreau <w@1wt.eu> Cc: Emese Revfy <re.emese@gmail.com> Signed-off-by: Thibaut Sautereau <thibaut.sautereau@ssi.gouv.fr> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-10-02Merge branch 'pm-cpufreq'Rafael J. Wysocki
* pm-cpufreq: cpufreq: intel_pstate: Fix missing return statement
2020-10-02mm: memcg/slab: fix slab statistics in !SMP configurationRoman Gushchin
Since commit ea426c2a7de8 ("mm: memcg: prepare for byte-sized vmstat items") the write side of slab counters accepts a value in bytes and converts it to pages. It happens in __mod_node_page_state(). However a non-SMP version of __mod_node_page_state() doesn't perform this conversion. It leads to incorrect (unrealistically high) slab counters values. Fix this by adding a similar conversion to the non-SMP version of __mod_node_page_state(). Signed-off-by: Roman Gushchin <guro@fb.com> Reported-and-tested-by: Bastian Bittorf <bb@npl.de> Fixes: ea426c2a7de8 ("mm: memcg: prepare for byte-sized vmstat items") Acked-by: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-10-01pipe: remove pipe_wait() and fix wakeup race with spliceLinus Torvalds
The pipe splice code still used the old model of waiting for pipe IO by using a non-specific "pipe_wait()" that waited for any pipe event to happen, which depended on all pipe IO being entirely serialized by the pipe lock. So by checking the state you were waiting for, and then adding yourself to the wait queue before dropping the lock, you were guaranteed to see all the wakeups. Strictly speaking, the actual wakeups were not done under the lock, but the pipe_wait() model still worked, because since the waiter held the lock when checking whether it should sleep, it would always see the current state, and the wakeup was always done after updating the state. However, commit 0ddad21d3e99 ("pipe: use exclusive waits when reading or writing") split the single wait-queue into two, and in the process also made the "wait for event" code wait for _two_ wait queues, and that then showed a race with the wakers that were not serialized by the pipe lock. It's only splice that used that "pipe_wait()" model, so the problem wasn't obvious, but Josef Bacik reports: "I hit a hang with fstest btrfs/187, which does a btrfs send into /dev/null. This works by creating a pipe, the write side is given to the kernel to write into, and the read side is handed to a thread that splices into a file, in this case /dev/null. The box that was hung had the write side stuck here [pipe_write] and the read side stuck here [splice_from_pipe_next -> pipe_wait]. [ more details about pipe_wait() scenario ] The problem is we're doing the prepare_to_wait, which sets our state each time, however we can be woken up either with reads or writes. In the case above we race with the WRITER waking us up, and re-set our state to INTERRUPTIBLE, and thus never break out of schedule" Josef had a patch that avoided the issue in pipe_wait() by just making it set the state only once, but the deeper problem is that pipe_wait() depends on a level of synchonization by the pipe mutex that it really shouldn't. And the whole "wait for any pipe state change" model really isn't very good to begin with. So rather than trying to work around things in pipe_wait(), remove that legacy model of "wait for arbitrary pipe event" entirely, and actually create functions that wait for the pipe actually being readable or writable, and can do so without depending on the pipe lock serializing everything. Fixes: 0ddad21d3e99 ("pipe: use exclusive waits when reading or writing") Link: https://lore.kernel.org/linux-fsdevel/bfa88b5ad6f069b2b679316b9e495a970130416c.1601567868.git.josef@toxicpanda.com/ Reported-by: Josef Bacik <josef@toxicpanda.com> Reviewed-and-tested-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-10-01Merge tag 'iommu-fixes-v5.9-rc7' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu Pull iommu fixes from Joerg Roedel: - Fix a device reference counting bug in the Exynos IOMMU driver. - Lockdep fix for the Intel VT-d driver. - Fix a bug in the AMD IOMMU driver which caused corruption of the IVRS ACPI table and caused IOMMU driver initialization failures in kdump kernels. * tag 'iommu-fixes-v5.9-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: iommu/vt-d: Fix lockdep splat in iommu_flush_dev_iotlb() iommu/amd: Fix the overwritten field in IVMD header iommu/exynos: add missing put_device() call in exynos_iommu_of_xlate()
2020-10-01Merge tag 'arm64-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux Pull arm64 fix from Catalin Marinas: "A previous commit to prevent AML memory opregions from accessing the kernel memory turned out to be too restrictive. Relax the permission check to permit the ACPI core to map kernel memory used for table overrides" * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: arm64: permit ACPI core to map kernel memory used for table overrides
2020-10-01Merge tag 'drm-fixes-2020-10-01-1' of git://anongit.freedesktop.org/drm/drmLinus Torvalds
Pull drm fixes from Dave Airlie: "AMD and vmwgfx fixes. Just dequeuing these a bit early as the AMD ones are bit larger than I'd prefer, but Alex missed last week so it's a double set of fixes. The larger ones are just register header fixes for the new chips that were just introduced in rc1 along with some new PCI IDs for new hw. Otherwise it is usual fixes. The vmwgfx fix was due to some testing I was doing and found we weren't booting properly, vmware had the fix internally so hurried it vmwgfx: - fix a regression due to TTM refactor amdgpu: - Fix potential double free in userptr handling - Sienna Cichlid and Navy Flounder udpates - Add Sienna Cichlid PCI IDs - Drop experimental flag for navi12 - Raven fixes - Renoir fixes - HDCP fix - DCN3 fix for clang and older versions of gcc - Fix a runtime pm refcount issue" * tag 'drm-fixes-2020-10-01-1' of git://anongit.freedesktop.org/drm/drm: drm/amdgpu: disable gfxoff temporarily for navy_flounder drm/amd/pm: setup APU dpm clock table in SMU HW initialization drm/vmwgfx: Fix error handling in get_node drm/amd/display: remove duplicate call to rn_vbios_smu_get_smu_version() drm/amdgpu/swsmu/smu12: fix force clock handling for mclk drm/amdgpu: restore proper ref count in amdgpu_display_crtc_set_config drm/amdgpu/display: fix CFLAGS setup for DCN30 drm/amd/display: fix return value check for hdcp_work drm/amdgpu: remove gpu_info fw support for sienna_cichlid etc. drm/amd/pm: Removed fixed clock in auto mode DPM drm/amdgpu: remove experimental flag from navi12 drm/amdgpu: add device ID for sienna_cichlid (v2) drm/amdgpu: use the AV1 defines for VCN 3.0 drm/amdgpu: add VCN 3.0 AV1 registers drm/amdgpu: add the GC 10.3 VRS registers drm/amdgpu: prevent double kfree ttm->sg
2020-10-01Merge tag 'trace-v5.9-rc6' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace Pull tracing fixes from Steven Rostedt: "Two tracing fixes: - Fix temp buffer accounting that caused a WARNING for ftrace_dump_on_opps() - Move the recursion check in one of the function callback helpers to the beginning of the function, as if the rcu_is_watching() gets traced, it will cause a recursive loop that will crash the kernel" * tag 'trace-v5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: ftrace: Move RCU is watching check after recursion check tracing: Fix trace_find_next_entry() accounting of temp buffer size
2020-10-01iommu/vt-d: Fix lockdep splat in iommu_flush_dev_iotlb()Lu Baolu
Lock(&iommu->lock) without disabling irq causes lockdep warnings. [ 12.703950] ======================================================== [ 12.703962] WARNING: possible irq lock inversion dependency detected [ 12.703975] 5.9.0-rc6+ #659 Not tainted [ 12.703983] -------------------------------------------------------- [ 12.703995] systemd-udevd/284 just changed the state of lock: [ 12.704007] ffffffffbd6ff4d8 (device_domain_lock){..-.}-{2:2}, at: iommu_flush_dev_iotlb.part.57+0x2e/0x90 [ 12.704031] but this lock took another, SOFTIRQ-unsafe lock in the past: [ 12.704043] (&iommu->lock){+.+.}-{2:2} [ 12.704045] and interrupts could create inverse lock ordering between them. [ 12.704073] other info that might help us debug this: [ 12.704085] Possible interrupt unsafe locking scenario: [ 12.704097] CPU0 CPU1 [ 12.704106] ---- ---- [ 12.704115] lock(&iommu->lock); [ 12.704123] local_irq_disable(); [ 12.704134] lock(device_domain_lock); [ 12.704146] lock(&iommu->lock); [ 12.704158] <Interrupt> [ 12.704164] lock(device_domain_lock); [ 12.704174] *** DEADLOCK *** Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Link: https://lore.kernel.org/r/20200927062428.13713-1-baolu.lu@linux.intel.com Signed-off-by: Joerg Roedel <jroedel@suse.de>
2020-10-01xen/events: don't use chip_data for legacy IRQsJuergen Gross
Since commit c330fb1ddc0a ("XEN uses irqdesc::irq_data_common::handler_data to store a per interrupt XEN data pointer which contains XEN specific information.") Xen is using the chip_data pointer for storing IRQ specific data. When running as a HVM domain this can result in problems for legacy IRQs, as those might use chip_data for their own purposes. Use a local array for this purpose in case of legacy IRQs, avoiding the double use. Cc: stable@vger.kernel.org Fixes: c330fb1ddc0a ("XEN uses irqdesc::irq_data_common::handler_data to store a per interrupt XEN data pointer which contains XEN specific information.") Signed-off-by: Juergen Gross <jgross@suse.com> Tested-by: Stefan Bader <stefan.bader@canonical.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Link: https://lore.kernel.org/r/20200930091614.13660-1-jgross@suse.com Signed-off-by: Juergen Gross <jgross@suse.com>
2020-10-01iommu/amd: Fix the overwritten field in IVMD headerAdrian Huang
Commit 387caf0b759a ("iommu/amd: Treat per-device exclusion ranges as r/w unity-mapped regions") accidentally overwrites the 'flags' field in IVMD (struct ivmd_header) when the I/O virtualization memory definition is associated with the exclusion range entry. This leads to the corrupted IVMD table (incorrect checksum). The kdump kernel reports the invalid checksum: ACPI BIOS Warning (bug): Incorrect checksum in table [IVRS] - 0x5C, should be 0x60 (20200717/tbprint-177) AMD-Vi: [Firmware Bug]: IVRS invalid checksum Fix the above-mentioned issue by modifying the 'struct unity_map_entry' member instead of the IVMD header. Cleanup: The *exclusion_range* functions are not used anymore, so get rid of them. Fixes: 387caf0b759a ("iommu/amd: Treat per-device exclusion ranges as r/w unity-mapped regions") Reported-and-tested-by: Baoquan He <bhe@redhat.com> Signed-off-by: Adrian Huang <ahuang12@lenovo.com> Cc: Jerry Snitselaar <jsnitsel@redhat.com> Link: https://lore.kernel.org/r/20200926102602.19177-1-adrianhuang0701@gmail.com Signed-off-by: Joerg Roedel <jroedel@suse.de>
2020-10-01KVM: arm64: Restore missing ISB on nVHE __tlb_switch_to_guestMarc Zyngier
Commit a0e50aa3f4a8 ("KVM: arm64: Factor out stage 2 page table data from struct kvm") dropped the ISB after __load_guest_stage2(), only leaving the one that is required when the speculative AT workaround is in effect. As Andrew points it: "This alternative is 'backwards' to avoid a double ISB as there is one in __load_guest_stage2 when the workaround is active." Restore the missing ISB, conditionned on the AT workaround not being active. Fixes: a0e50aa3f4a8 ("KVM: arm64: Factor out stage 2 page table data from struct kvm") Reported-by: Andrew Scull <ascull@google.com> Reported-by: Thomas Tai <thomas.tai@oracle.com> Signed-off-by: Marc Zyngier <maz@kernel.org>
2020-10-01gpio: pca953x: Correctly initialize registers 6 and 7 for PCA957xAndy Shevchenko
When driver has been converted to the bitmap API the non-bitmap functions started behaving differently on 32-bit BE architectures since the bytes in two consequent unsigned longs are in different order in comparison to byte array. Hence if the chip had had more than 32 lines the memset() call over it would have not set up upper lines correctly. Although it's currently a theoretical case (no supported chips of this type has 32+ lines), it's better to provide a clean code to avoid people thinking this is okay and potentially producing not fully working things. Fixes: 35d13d94893f ("gpio: pca953x: convert to use bitmap API") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Link: https://lore.kernel.org/r/20200930142013.59247-2-andriy.shevchenko@linux.intel.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-10-01gpio: pca953x: Use bitmap API over implicit GCC extensionAndy Shevchenko
In IRQ handler we have to clear bitmap before use. Currently the GCC extension has been used for that. For sake of the consistency switch to bitmap API. As expected bloat-o-meter shows no difference in the object size. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Link: https://lore.kernel.org/r/20200930142013.59247-1-andriy.shevchenko@linux.intel.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-10-01pinctrl: mediatek: check mtk_is_virt_gpio input parameterHanks Chen
check mtk_is_virt_gpio input parameter, virtual gpio need to support eint mode. add error handler for the ko case to fix this boot fail: pc : mtk_is_virt_gpio+0x20/0x38 [pinctrl_mtk_common_v2] lr : mtk_gpio_get_direction+0x44/0xb0 [pinctrl_paris] Fixes: edd546465002 ("pinctrl: mediatek: avoid virtual gpio trying to set reg") Signed-off-by: Hanks Chen <hanks.chen@mediatek.com> Acked-by: Sean Wang <sean.wang@kernel.org> Singed-off-by: Jie Yang <sin_jieyang@mediatek.com> Link: https://lore.kernel.org/r/1597922546-29633-1-git-send-email-hanks.chen@mediatek.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-10-01pinctrl: qcom: sm8250: correct sdc2_clkDmitry Baryshkov
Correct sdc2_clk pin definition (register offset is wrong, verified by the msm-4.19 driver). Fixes: 4e3ec9e407ad ("pinctrl: qcom: Add sm8250 pinctrl driver.") Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20200914091846.55204-1-dmitry.baryshkov@linaro.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-10-01Merge tag 'amd-drm-fixes-5.9-2020-09-30' of ↵Dave Airlie
git://people.freedesktop.org/~agd5f/linux into drm-fixes amd-drm-fixes-5.9-2020-09-30: amdgpu: - Fix potential double free in userptr handling - Sienna Cichlid and Navy Flounder udpates - Add Sienna Cichlid PCI IDs - Drop experimental flag for navi12 - Raven fixes - Renoir fixes - HDCP fix - DCN3 fix for clang and older versions of gcc - Fix a runtime pm refcount issue Signed-off-by: Dave Airlie <airlied@redhat.com> From: Alex Deucher <alexdeucher@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200930161326.4243-1-alexander.deucher@amd.com
2020-09-30MAINTAINERS: Add Pali Rohár as aardvark PCI maintainerPali Rohár
Link: https://lore.kernel.org/r/20200925092115.16546-1-pali@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Petazzzoni <thomas.petazzoni@bootlin.com>
2020-09-30arm64: permit ACPI core to map kernel memory used for table overridesArd Biesheuvel
Jonathan reports that the strict policy for memory mapped by the ACPI core breaks the use case of passing ACPI table overrides via initramfs. This is due to the fact that the memory type used for loading the initramfs in memory is not recognized as a memory type that is typically used by firmware to pass firmware tables. Since the purpose of the strict policy is to ensure that no AML or other ACPI code can manipulate any memory that is used by the kernel to keep its internal state or the state of user tasks, we can relax the permission check, and allow mappings of memory that is reserved and marked as NOMAP via memblock, and therefore not covered by the linear mapping to begin with. Fixes: 1583052d111f ("arm64/acpi: disallow AML memory opregions to access kernel memory") Fixes: 325f5585ec36 ("arm64/acpi: disallow writeable AML opregion mapping for EFI code regions") Reported-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Cc: Sudeep Holla <sudeep.holla@arm.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Link: https://lore.kernel.org/r/20200929132522.18067-1-ardb@kernel.org Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2020-09-30Merge tag 'clk-fixes-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux Pull clk fixes from Stephen Boyd: "Another batch of clk driver fixes: - Make sure DRAM and ChipID region doesn't get disabled on Exynos - Fix a SATA failure on Tegra - Fix the emac_ptp clk divider on stratix10" * tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: clk: socfpga: stratix10: fix the divider for the emac_ptp_free_clk clk: samsung: exynos4: mark 'chipid' clock as CLK_IGNORE_UNUSED clk: tegra: Fix missing prototype for tegra210_clk_register_emc() clk: tegra: Always program PLL_E when enabled clk: tegra: Capitalization fixes clk: samsung: Keep top BPLL mux on Exynos542x enabled
2020-09-30RISC-V: Check clint_time_val before useAnup Patel
The NoMMU kernel is broken for QEMU virt machine from Linux-5.9-rc6 because clint_time_val is used even before CLINT driver is probed at following places: 1. rand_initialize() calls get_cycles() which in-turn uses clint_time_val 2. boot_init_stack_canary() calls get_cycles() which in-turn uses clint_time_val The issue#1 (above) is fixed by providing custom random_get_entropy() for RISC-V NoMMU kernel. For issue#2 (above), we remove dependency of boot_init_stack_canary() on get_cycles() and this is aligned with the boot_init_stack_canary() implementations of ARM, ARM64 and MIPS kernel. Fixes: d5be89a8d118 ("RISC-V: Resurrect the MMIO timer implementation for M-mode systems") Signed-off-by: Anup Patel <anup.patel@wdc.com> Tested-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
2020-09-30btrfs: fix filesystem corruption after a device replaceFilipe Manana
We use a device's allocation state tree to track ranges in a device used for allocated chunks, and we set ranges in this tree when allocating a new chunk. However after a device replace operation, we were not setting the allocated ranges in the new device's allocation state tree, so that tree is empty after a device replace. This means that a fitrim operation after a device replace will trim the device ranges that have allocated chunks and extents, as we trim every range for which there is not a range marked in the device's allocation state tree. It is also important during chunk allocation, since the device's allocation state is used to determine if a range is already allocated when allocating a new chunk. This is trivial to reproduce and the following script triggers the bug: $ cat reproducer.sh #!/bin/bash DEV1="/dev/sdg" DEV2="/dev/sdh" DEV3="/dev/sdi" wipefs -a $DEV1 $DEV2 $DEV3 &> /dev/null # Create a raid1 test fs on 2 devices. mkfs.btrfs -f -m raid1 -d raid1 $DEV1 $DEV2 > /dev/null mount $DEV1 /mnt/btrfs xfs_io -f -c "pwrite -S 0xab 0 10M" /mnt/btrfs/foo echo "Starting to replace $DEV1 with $DEV3" btrfs replace start -B $DEV1 $DEV3 /mnt/btrfs echo echo "Running fstrim" fstrim /mnt/btrfs echo echo "Unmounting filesystem" umount /mnt/btrfs echo "Mounting filesystem in degraded mode using $DEV3 only" wipefs -a $DEV1 $DEV2 &> /dev/null mount -o degraded $DEV3 /mnt/btrfs if [ $? -ne 0 ]; then dmesg | tail echo echo "Failed to mount in degraded mode" exit 1 fi echo echo "File foo data (expected all bytes = 0xab):" od -A d -t x1 /mnt/btrfs/foo umount /mnt/btrfs When running the reproducer: $ ./replace-test.sh wrote 10485760/10485760 bytes at offset 0 10 MiB, 2560 ops; 0.0901 sec (110.877 MiB/sec and 28384.5216 ops/sec) Starting to replace /dev/sdg with /dev/sdi Running fstrim Unmounting filesystem Mounting filesystem in degraded mode using /dev/sdi only mount: /mnt/btrfs: wrong fs type, bad option, bad superblock on /dev/sdi, missing codepage or helper program, or other error. [19581.748641] BTRFS info (device sdg): dev_replace from /dev/sdg (devid 1) to /dev/sdi started [19581.803842] BTRFS info (device sdg): dev_replace from /dev/sdg (devid 1) to /dev/sdi finished [19582.208293] BTRFS info (device sdi): allowing degraded mounts [19582.208298] BTRFS info (device sdi): disk space caching is enabled [19582.208301] BTRFS info (device sdi): has skinny extents [19582.212853] BTRFS warning (device sdi): devid 2 uuid 1f731f47-e1bb-4f00-bfbb-9e5a0cb4ba9f is missing [19582.213904] btree_readpage_end_io_hook: 25839 callbacks suppressed [19582.213907] BTRFS error (device sdi): bad tree block start, want 30490624 have 0 [19582.214780] BTRFS warning (device sdi): failed to read root (objectid=7): -5 [19582.231576] BTRFS error (device sdi): open_ctree failed Failed to mount in degraded mode So fix by setting all allocated ranges in the replace target device when the replace operation is finishing, when we are holding the chunk mutex and we can not race with new chunk allocations. A test case for fstests follows soon. Fixes: 1c11b63eff2a67 ("btrfs: replace pending/pinned chunks lists with io tree") CC: stable@vger.kernel.org # 5.2+ Reviewed-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
generated by cgit (git 2.34.1) at 2024-06-02 20:05:47 +0000