| Age | Commit message (Collapse) | Author |
|---|
|
Pull ARM fixes from Russell King:
"Two further fixes for Spectre-BHB from Ard for Cortex A15 and to use
the wide branch instruction for Thumb2"
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9197/1: spectre-bhb: fix loop8 sequence for Thumb2
ARM: 9196/1: spectre-bhb: enable for Cortex-A15
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Fix an altmode in the Ocelot driver
- Fix the IES control pins in the Mediatek MT8365 driver
- Sunxi (AMLogic) driver:
- Fix the UART2 function pin assignments
- Fix the signal name of the PA2 SPI pin
* tag 'pinctrl-v5.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: sunxi: f1c100s: Fix signal name comment for PA2 SPI pin
pinctrl: sunxi: fix f1c100s uart2 function
pinctrl: mediatek: mt8365: fix IES control pins
pinctrl: ocelot: Fix for lan966x alt mode
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from can, xfrm and netfilter subtrees.
Notably this reverts a recent TCP/DCCP netns-related change to address
a possible UaF.
Current release - regressions:
- tcp: revert "tcp/dccp: get rid of inet_twsk_purge()"
- xfrm: set dst dev to blackhole_netdev instead of loopback_dev in
ifdown
Previous releases - regressions:
- netfilter: flowtable: fix TCP flow teardown
- can: revert "can: m_can: pci: use custom bit timings for Elkhart
Lake"
- xfrm: check encryption module availability consistency
- eth: vmxnet3: fix possible use-after-free bugs in
vmxnet3_rq_alloc_rx_buf()
- eth: mlx5: initialize flow steering during driver probe
- eth: ice: fix crash when writing timestamp on RX rings
Previous releases - always broken:
- mptcp: fix checksum byte order
- eth: lan966x: fix assignment of the MAC address
- eth: mlx5: remove HW-GRO from reported features
- eth: ftgmac100: disable hardware checksum on AST2600"
* tag 'net-5.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (50 commits)
net: bridge: Clear offload_fwd_mark when passing frame up bridge interface.
ptp: ocp: change sysfs attr group handling
selftests: forwarding: fix missing backslash
netfilter: nf_tables: disable expression reduction infra
netfilter: flowtable: move dst_check to packet path
netfilter: flowtable: fix TCP flow teardown
net: ftgmac100: Disable hardware checksum on AST2600
igb: skip phy status check where unavailable
nfc: pn533: Fix buggy cleanup order
mptcp: Do TCP fallback on early DSS checksum failure
mptcp: fix checksum byte order
net: af_key: check encryption module availability consistency
net: af_key: add check for pfkey_broadcast in function pfkey_process
net/mlx5: Drain fw_reset when removing device
net/mlx5e: CT: Fix setting flow_source for smfs ct tuples
net/mlx5e: CT: Fix support for GRE tuples
net/mlx5e: Remove HW-GRO from reported features
net/mlx5e: Properly block HW GRO when XDP is enabled
net/mlx5e: Properly block LRO when XDP is enabled
net/mlx5e: Block rx-gro-hw feature in switchdev mode
...
|
|
It is possible to stack bridges on top of each other. Consider the
following which makes use of an Ethernet switch:
br1
/ \
/ \
/ \
br0.11 wlan0
|
br0
/ | \
p1 p2 p3
br0 is offloaded to the switch. Above br0 is a vlan interface, for
vlan 11. This vlan interface is then a slave of br1. br1 also has a
wireless interface as a slave. This setup trunks wireless lan traffic
over the copper network inside a VLAN.
A frame received on p1 which is passed up to the bridge has the
skb->offload_fwd_mark flag set to true, indicating that the switch has
dealt with forwarding the frame out ports p2 and p3 as needed. This
flag instructs the software bridge it does not need to pass the frame
back down again. However, the flag is not getting reset when the frame
is passed upwards. As a result br1 sees the flag, wrongly interprets
it, and fails to forward the frame to wlan0.
When passing a frame upwards, clear the flag. This is the Rx
equivalent of br_switchdev_frame_unmark() in br_dev_xmit().
Fixes: f1c2eddf4cb6 ("bridge: switchdev: Use an helper to clear forward mark")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20220518005840.771575-1-andrew@lunn.ch
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In the detach path, the driver calls sysfs_remove_group() for the
groups it believes has been registered. However, if the group was
never previously registered, then this causes a splat.
Instead, compute the groups that should be registered in advance,
and then call sysfs_create_groups(), which registers them all at once.
Update the error handling appropriately.
Fixes: c205d53c4923 ("ptp: ocp: Add firmware capability bits for feature gating")
Reported-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Link: https://lore.kernel.org/r/20220517214600.10606-1-jonathan.lemon@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix missing backslash, introduced in f62c5acc800ee. Causes all tests to
not be installed.
Fixes: f62c5acc800e ("selftests/net/forwarding: add missing tests to Makefile")
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Acked-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://lore.kernel.org/r/20220518151630.2747773-1-troglobit@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Reduce number of hardware offload retries from flowtable datapath
which might hog system with retries, from Felix Fietkau.
2) Skip neighbour lookup for PPPoE device, fill_forward_path() already
provides this and set on destination address from fill_forward_path for
PPPoE device, also from Felix.
4) When combining PPPoE on top of a VLAN device, set info->outdev to the
PPPoE device so software offload works, from Felix.
5) Fix TCP teardown flowtable state, races with conntrack gc might result
in resetting the state to ESTABLISHED and the time to one day. Joint
work with Oz Shlomo and Sven Auhagen.
6) Call dst_check() from flowtable datapath to check if dst is stale
instead of doing it from garbage collector path.
7) Disable register tracking infrastructure, either user-space or
kernel need to pre-fetch keys inconditionally, otherwise register
tracking assumes data is already available in register that might
not well be there, leading to incorrect reductions.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_tables: disable expression reduction infra
netfilter: flowtable: move dst_check to packet path
netfilter: flowtable: fix TCP flow teardown
netfilter: nft_flow_offload: fix offload with pppoe + vlan
net: fix dev_fill_forward_path with pppoe + bridge
netfilter: nft_flow_offload: skip dst neigh lookup for ppp devices
netfilter: flowtable: fix excessive hw offload attempts after failure
====================
Link: https://lore.kernel.org/r/20220518213841.359653-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull block fix from Jens Axboe:
"Just a small fix for a missing fifo time assigment for the head
insertion case in mq-deadline"
* tag 'block-5.18-2022-05-18' of git://git.kernel.dk/linux-block:
block/mq-deadline: Set the fifo_time member also if inserting at head
|
|
Pull io_uring fixes from Jens Axboe:
"Two small changes fixing issues from the 5.18 merge window:
- Fix wrong ordering of a tracepoint (Dylan)
- Fix MSG_RING on IOPOLL rings (me)"
* tag 'io_uring-5.18-2022-05-18' of git://git.kernel.dk/linux-block:
io_uring: don't attempt to IOPOLL for MSG_RING requests
io_uring: fix ordering of args in io_uring_queue_async_work
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit fix from Paul Moore:
"A single audit patch to fix a problem where a task's audit_context was
not being properly reset with io_uring"
* tag 'audit-pr-20220518' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit,io_uring,io-wq: call __audit_uring_exit for dummy contexts
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux
Pull selinux fix from Paul Moore:
"A single SELinux patch to fix an error path that was doing the wrong
thing with respect to freeing memory"
* tag 'selinux-pr-20220518' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: fix bad cleanup on error in hashtab_duplicate()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"The SoC bug fixes have calmed down sufficiently, there is one minor
update for the MAINTAINERS file, and few bug fixes for dts
descriptions:
- Updates to the BananaPi R2-Pro (rk3568) dts to match production
hardware rather than the prototype version.
- Qualcomm sm8250 soundwire gets disabled on some machines to avoid
crashes
- A number of aspeed SoC specific fixes, addressing incorrect pin
cotrol settings, some values in the romed8hm board, and a revert
for an accidental removal of a DT node"
* 'arm/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
MAINTAINERS: omap: remove me as a maintainer
ARM: dts: aspeed: Add video engine to g6
ARM: dts: aspeed: romed8hm3: Fix GPIOB0 name
ARM: dts: aspeed: romed8hm3: Add lm25066 sense resistor values
ARM: dts: aspeed-g6: fix SPI1/SPI2 quad pin group
ARM: dts: aspeed-g6: add FWQSPI group in pinctrl dtsi
dt-bindings: pinctrl: aspeed-g6: add FWQSPI function/group
pinctrl: pinctrl-aspeed-g6: add FWQSPI function-group
dt-bindings: pinctrl: aspeed-g6: remove FWQSPID group
pinctrl: pinctrl-aspeed-g6: remove FWQSPID group in pinctrl
ARM: dts: aspeed-g6: remove FWQSPID group in pinctrl dtsi
arm64: dts: qcom: sm8250: don't enable rx/tx macro by default
arm64: dts: rockchip: Add gmac1 and change network settings of bpi-r2-pro
arm64: dts: rockchip: Change io-domains of bpi-r2-pro
|
|
Pull misc fixes from Al Viro:
"vhost race fix and a percpu_ref_init-caused cgroup double-free fix.
The latter had manifested as buggered struct mount refcounting - those
are also using percpu data structures, but anything that does percpu
allocations could be hit"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Fix double fget() in vhost_net_set_backend()
percpu_ref_init(): clean ->percpu_count_ref on failure
|
|
Pull mlx5 fix from Michael Tsirkin:
"One last minute fixup
The patch has been on list for a while but as it was posted as part of
a thread it was missed"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vdpa/mlx5: Use consistent RQT size
|
|
Descriptor table is a shared resource; two fget() on the same descriptor
may return different struct file references. get_tap_ptr_ring() is
called after we'd found (and pinned) the socket we'll be using and it
tries to find the private tun/tap data structures associated with it.
Redoing the lookup by the same file descriptor we'd used to get the
socket is racy - we need to same struct file.
Thanks to Jason for spotting a braino in the original variant of patch -
I'd missed the use of fd == -1 for disabling backend, and in that case
we can end up with sock == NULL and sock != oldsock.
Cc: stable@kernel.org
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
The current code evaluates RQT size based on the configured number of
virtqueues. This can raise an issue in the following scenario:
Assume MQ was negotiated.
1. mlx5_vdpa_set_map() gets called.
2. handle_ctrl_mq() is called setting cur_num_vqs to some value, lower
than the configured max VQs.
3. A second set_map gets called, but now a smaller number of VQs is used
to evaluate the size of the RQT.
4. handle_ctrl_mq() is called with a value larger than what the RQT can
hold. This will emit errors and the driver state is compromised.
To fix this, we use a new field in struct mlx5_vdpa_net to hold the
required number of entries in the RQT. This value is evaluated in
mlx5_vdpa_set_driver_features() where we have the negotiated features
all set up.
In addition to that, we take into consideration the max capability of RQT
entries early when the device is added so we don't need to take consider
it when creating the RQT.
Last, we remove the use of mlx5_vdpa_max_qps() which just returns the
max_vas / 2 and make the code clearer.
Fixes: 52893733f2c5 ("vdpa/mlx5: Add multiqueue support")
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of last-minute HD- an USB-audio quirks in addition to a
fix for the legacy ISA wavefront driver.
All look small and easy"
* tag 'sound-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Restore Rane SL-1 quirk
ALSA: hda/realtek: fix right sounds and mute/micmute LEDs for HP machine
ALSA: hda/realtek: Add quirk for TongFang devices with pop noise
ALSA: hda/realtek: Add quirk for the Framework Laptop
ALSA: wavefront: Proper check of get_user() error
ALSA: hda/realtek: Add quirk for Dell Latitude 7520
ALSA: hda - fix unused Realtek function when PM is not enabled
ALSA: usb-audio: Don't get sample rate for MCT Trigger 5 USB-to-HDMI
|
|
Either userspace or kernelspace need to pre-fetch keys inconditionally
before comparisons for this to work. Otherwise, register tracking data
is misleading and it might result in reducing expressions which are not
yet registers.
First expression is also guaranteed to be evaluated always, however,
certain expressions break before writing data to registers, before
comparing the data, leaving the register in undetermined state.
This patch disables this infrastructure by now.
Fixes: b2d306542ff9 ("netfilter: nf_tables: do not reduce read-only expressions")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Fixes sporadic IPv6 packet loss when flow offloading is enabled.
IPv6 route GC and flowtable GC are not synchronized.
When dst_cache becomes stale and a packet passes through the flow before
the flowtable GC teardowns it, the packet can be dropped.
So, it is necessary to check dst every time in packet path.
Fixes: 227e1e4d0d6c ("netfilter: nf_flowtable: skip device lookup from interface index")
Signed-off-by: Ritaro Takenaka <ritarot634@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch addresses three possible problems:
1. ct gc may race to undo the timeout adjustment of the packet path, leaving
the conntrack entry in place with the internal offload timeout (one day).
2. ct gc removes the ct because the IPS_OFFLOAD_BIT is not set and the CLOSE
timeout is reached before the flow offload del.
3. tcp ct is always set to ESTABLISHED with a very long timeout
in flow offload teardown/delete even though the state might be already
CLOSED. Also as a remark we cannot assume that the FIN or RST packet
is hitting flow table teardown as the packet might get bumped to the
slow path in nftables.
This patch resets IPS_OFFLOAD_BIT from flow_offload_teardown(), so
conntrack handles the tcp rst/fin packet which triggers the CLOSE/FIN
state transition.
Moreover, teturn the connection's ownership to conntrack upon teardown
by clearing the offload flag and fixing the established timeout value.
The flow table GC thread will asynchonrnously free the flow table and
hardware offload entries.
Before this patch, the IPS_OFFLOAD_BIT remained set for expired flows on
which is also misleading since the flow is back to classic conntrack
path.
If nf_ct_delete() removes the entry from the conntrack table, then it
calls nf_ct_put() which decrements the refcnt. This is not a problem
because the flowtable holds a reference to the conntrack object from
flow_offload_alloc() path which is released via flow_offload_free().
This patch also updates nft_flow_offload to skip packets in SYN_RECV
state. Since we might miss or bump packets to slow path, we do not know
what will happen there while we are still in SYN_RECV, this patch
postpones offload up to the next packet which also aligns to the
existing behaviour in tc-ct.
flow_offload_teardown() does not reset the existing tcp state from
flow_offload_fixup_tcp() to ESTABLISHED anymore, packets bump to slow
path might have already update the state to CLOSE/FIN.
Joint work with Oz and Sven.
Fixes: 1e5b2471bcc4 ("netfilter: nf_flow_table: teardown flow timeout race")
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The AST2600 when using the i210 NIC over NC-SI has been observed to
produce incorrect checksum results with specific MTU values. This was
first observed when sending data across a long distance set of networks.
On a local network, the following test was performed using a 1MB file of
random data.
On the receiver run this script:
#!/bin/bash
while [ 1 ]; do
# Zero the stats
nstat -r > /dev/null
nc -l 9899 > test-file
# Check for checksum errors
TcpInCsumErrors=$(nstat | grep TcpInCsumErrors)
if [ -z "$TcpInCsumErrors" ]; then
echo No TcpInCsumErrors
else
echo TcpInCsumErrors = $TcpInCsumErrors
fi
done
On an AST2600 system:
# nc <IP of receiver host> 9899 < test-file
The test was repeated with various MTU values:
# ip link set mtu 1410 dev eth0
The observed results:
1500 - good
1434 - bad
1400 - good
1410 - bad
1420 - good
The test was repeated after disabling tx checksumming:
# ethtool -K eth0 tx-checksumming off
And all MTU values tested resulted in transfers without error.
An issue with the driver cannot be ruled out, however there has been no
bug discovered so far.
David has done the work to take the original bug report of slow data
transfer between long distance connections and triaged it down to this
test case.
The vendor suspects this this is a hardware issue when using NC-SI. The
fixes line refers to the patch that introduced AST2600 support.
Reported-by: David Wilder <wilder@us.ibm.com>
Reviewed-by: Dylan Hung <dylan_hung@aspeedtech.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
igb_read_phy_reg() will silently return, leaving phy_data untouched, if
hw->ops.read_reg isn't set. Depending on the uninitialized value of
phy_data, this led to the phy status check either succeeding immediately
or looping continuously for 2 seconds before emitting a noisy err-level
timeout. This message went out to the console even though there was no
actual problem.
Instead, first check if there is read_reg function pointer. If not,
proceed without trying to check the phy status register.
Fixes: b72f3f72005d ("igb: When GbE link up, wait for Remote receiver status condition")
Signed-off-by: Kevin Mitchell <kevmitch@arista.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When removing the pn533 device (i2c or USB), there is a logic error. The
original code first cancels the worker (flush_delayed_work) and then
destroys the workqueue (destroy_workqueue), leaving the timer the last
one to be deleted (del_timer). This result in a possible race condition
in a multi-core preempt-able kernel. That is, if the cleanup
(pn53x_common_clean) is concurrently run with the timer handler
(pn533_listen_mode_timer), the timer can queue the poll_work to the
already destroyed workqueue, causing use-after-free.
This patch reorder the cleanup: it uses the del_timer_sync to make sure
the handler is finished before the routine will destroy the workqueue.
Note that the timer cannot be activated by the worker again.
static void pn533_wq_poll(struct work_struct *work)
...
rc = pn533_send_poll_frame(dev);
if (rc)
return;
if (cur_mod->len == 0 && dev->poll_mod_count > 1)
mod_timer(&dev->listen_timer, ...);
That is, the mod_timer can be called only when pn533_send_poll_frame()
returns no error, which is impossible because the device is detaching
and the lower driver should return ENODEV code.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Mat Martineau says:
====================
mptcp: Fix checksum byte order on little-endian
These patches address a bug in the byte ordering of MPTCP checksums on
little-endian architectures. The __sum16 type is always big endian, but
was being cast to u16 and then byte-swapped (on little-endian archs)
when reading/writing the checksum field in MPTCP option headers.
MPTCP checksums are off by default, but are enabled if one or both peers
request it in the SYN/SYNACK handshake.
The corrected code is verified to interoperate between big-endian and
little-endian machines.
Patch 1 fixes the checksum byte order, patch 2 partially mitigates
interoperation with peers sending bad checksums by falling back to TCP
instead of resetting the connection.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RFC 8684 section 3.7 describes several opportunities for a MPTCP
connection to "fall back" to regular TCP early in the connection
process, before it has been confirmed that MPTCP options can be
successfully propagated on all SYN, SYN/ACK, and data packets. If a peer
acknowledges the first received data packet with a regular TCP header
(no MPTCP options), fallback is allowed.
If the recipient of that first data packet finds a MPTCP DSS checksum
error, this provides an opportunity to fail gracefully with a TCP
fallback rather than resetting the connection (as might happen if a
checksum failure were detected later).
This commit modifies the checksum failure code to attempt fallback on
the initial subflow of a MPTCP connection, only if it's a failure in the
first data mapping. In cases where the peer initiates the connection,
requests checksums, is the first to send data, and the peer is sending
incorrect checksums (see
https://github.com/multipath-tcp/mptcp_net-next/issues/275), this allows
the connection to proceed as TCP rather than reset.
Fixes: dd8bcd1768ff ("mptcp: validate the data checksum")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MPTCP code typecasts the checksum value to u16 and
then converts it to big endian while storing the value into
the MPTCP option.
As a result, the wire encoding for little endian host is
wrong, and that causes interoperabilty interoperability
issues with other implementation or host with different endianness.
Address the issue writing in the packet the unmodified __sum16 value.
MPTCP checksum is disabled by default, interoperating with systems
with bad mptcp-level csum encoding should cause fallback to TCP.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/275
Fixes: c5b39e26d003 ("mptcp: send out checksum for DSS")
Fixes: 390b95a5fb84 ("mptcp: receive checksum for DSS")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-05-17
This series contains updates to ice driver only.
Arkadiusz prevents writing of timestamps when rings are being
configured to resolve null pointer dereference.
Paul changes a delayed call to baseline statistics to occur immediately
which was causing misreporting of statistics due to the delay.
Michal fixes incorrect restoration of interrupt moderation settings.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2022-05-18
1) Fix "disable_policy" flag use when arriving from different devices.
From Eyal Birger.
2) Fix error handling of pfkey_broadcast in function pfkey_process.
From Jiasheng Jiang.
3) Check the encryption module availability consistency in pfkey.
From Thomas Bartschies.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In Thumb2, 'b . + 4' produces a branch instruction that uses a narrow
encoding, and so it does not jump to the following instruction as
expected. So use W(b) instead.
Fixes: 6c7cb60bff7a ("ARM: fix Thumb2 regression with Spectre BHB")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
The Spectre-BHB mitigations were inadvertently left disabled for
Cortex-A15, due to the fact that cpu_v7_bugs_init() is not called in
that case. So fix that.
Fixes: b9baf5c8c5c3 ("ARM: Spectre-BHB workaround")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2022-05-17
This series provides bug fixes to mlx5 driver.
Please pull and let me know if there is any problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the recent introduction supporting the SM3 and SM4 hash algos for IPsec, the kernel
produces invalid pfkey acquire messages, when these encryption modules are disabled. This
happens because the availability of the algos wasn't checked in all necessary functions.
This patch adds these checks.
Signed-off-by: Thomas Bartschies <thomas.bartschies@cvk.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
If skb_clone() returns null pointer, pfkey_broadcast() will
return error.
Therefore, it should be better to check the return value of
pfkey_broadcast() and return error if fails.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
That way percpu_ref_exit() is safe after failing percpu_ref_init().
At least one user (cgroup_create()) had a double-free that way;
there might be other similar bugs. Easier to fix in percpu_ref_init(),
rather than playing whack-a-mole in sloppy users...
Usual symptoms look like a messed refcounting in one of subsystems
that use percpu allocations (might be percpu-refcount, might be
something else). Having refcounts for two different objects share
memory is Not Nice(tm)...
Reported-by: syzbot+5b1e53987f858500ec00@syzkaller.appspotmail.com
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
In case fw sync reset is called in parallel to device removal, device
might stuck in the following deadlock:
CPU 0 CPU 1
----- -----
remove_one
uninit_one (locks intf_state_mutex)
mlx5_sync_reset_now_event()
work in fw_reset->wq.
mlx5_enter_error_state()
mutex_lock (intf_state_mutex)
cleanup_once
fw_reset_cleanup()
destroy_workqueue(fw_reset->wq)
Drain the fw_reset WQ, and make sure no new work is being queued, before
entering uninit_one().
The Drain is done before devlink_unregister() since fw_reset, in some
flows, is using devlink API devlink_remote_reload_actions_performed().
Fixes: 38b9f903f22b ("net/mlx5: Handle sync reset request event")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Cited patch sets flow_source to ANY overriding the provided spec
flow_source, avoiding the optimization done by commit c9c079b4deaa
("net/mlx5: CT: Set flow source hint from provided tuple device").
To fix the above, set the dr_rule flow_source from provided flow spec.
Fixes: 3ee61ebb0df1 ("net/mlx5: CT: Add software steering ct flow steering provider")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
cited commit removed support for GRE tuples when software steering was enabled.
To bring back support for GRE tuples, add GRE ipv4/ipv6 matchers.
Fixes: 3ee61ebb0df1 ("net/mlx5: CT: Add software steering ct flow steering provider")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
We got reports of certain HW-GRO flows causing kernel call traces, which
might be related to firmware. To be on the safe side, disable the
feature for now and re-enable it once a driver/firmware fix is found.
Fixes: 83439f3c37aa ("net/mlx5e: Add HW-GRO offload")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
HW GRO is incompatible and mutually exclusive with XDP and XSK. However,
the needed checks are only made when enabling XDP. If HW GRO is enabled
when XDP is already active, the command will succeed, and XDP will be
skipped in the data path, although still enabled.
This commit fixes the bug by checking the XDP and XSK status in
mlx5e_fix_features and disabling HW GRO if XDP is enabled.
Fixes: 83439f3c37aa ("net/mlx5e: Add HW-GRO offload")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
LRO is incompatible and mutually exclusive with XDP. However, the needed
checks are only made when enabling XDP. If LRO is enabled when XDP is
already active, the command will succeed, and XDP will be skipped in the
data path, although still enabled.
This commit fixes the bug by checking the XDP status in
mlx5e_fix_features and disabling LRO if XDP is enabled.
Fixes: 86994156c736 ("net/mlx5e: XDP fast RX drop bpf programs support")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When the driver is in switchdev mode and rx-gro-hw is set, the RQ needs
special CQE handling. Till then, block setting of rx-gro-hw feature in
switchdev mode, to avoid failure while setting the feature due to
failure while opening the RQ.
Fixes: f97d5c2a453e ("net/mlx5e: Add handle SHAMPO cqe support")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The body of mlx5e_napi_poll is wrapped into rcu_read_lock to be able to
read the XDP program pointer using rcu_dereference. However, the trap RQ
NAPI doesn't use rcu_read_lock, because the trap RQ works only in the
non-linear mode, and mlx5e_skb_from_cqe_nonlinear, until recently,
didn't support XDP and didn't call rcu_dereference.
Starting from the cited commit, mlx5e_skb_from_cqe_nonlinear supports
XDP and calls rcu_dereference, but mlx5e_trap_napi_poll doesn't wrap it
into rcu_read_lock. It leads to RCU-lockdep warnings like this:
WARNING: suspicious RCU usage
This commit fixes the issue by adding an rcu_read_lock to
mlx5e_trap_napi_poll, similarly to mlx5e_napi_poll.
Fixes: ea5d49bdae8b ("net/mlx5e: Add XDP multi buffer support to the non-linear legacy RQ")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When modifying TTL, packet's csum has to be recalculated.
Due to HW issue in ConnectX-5, csum recalculation for modify
TTL on RX is supported through a work-around that is specifically
enabled by configuration.
If the work-around isn't enabled, rather than adding an unsupported
action the modify TTL action on RX should be ignored.
Ignoring modify TTL action might result in zero actions, so in such
cases we will not convert the match STE to modify STE, as it is done
by FW in DMFS.
This patch fixes an issue where modify TTL action was ignored both
on RX and TX instead of only on RX.
Fixes: 4ff725e1d4ad ("net/mlx5: DR, Ignore modify TTL if device doesn't support it")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently, software objects of flow steering are created and destroyed
during reload flow. In case a device is unloaded, the following error
is printed during grace period:
mlx5_core 0000:00:0b.0: mlx5_fw_fatal_reporter_err_work:690:(pid 95):
Driver is in error state. Unloading
As a solution to fix use-after-free bugs, where we try to access
these objects, when reading the value of flow_steering_mode devlink
param[1], let's split flow steering creation and destruction into two
routines:
* init and cleanup: memory, cache, and pools allocation/free.
* create and destroy: namespaces initialization and cleanup.
While at it, re-order the cleanup function to mirror the init function.
[1]
Kasan trace:
[ 385.119849 ] BUG: KASAN: use-after-free in mlx5_devlink_fs_mode_get+0x3b/0xa0
[ 385.119849 ] Read of size 4 at addr ffff888104b79308 by task bash/291
[ 385.119849 ]
[ 385.119849 ] CPU: 1 PID: 291 Comm: bash Not tainted 5.17.0-rc1+ #2
[ 385.119849 ] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-2.fc32 04/01/2014
[ 385.119849 ] Call Trace:
[ 385.119849 ] <TASK>
[ 385.119849 ] dump_stack_lvl+0x6e/0x91
[ 385.119849 ] print_address_description.constprop.0+0x1f/0x160
[ 385.119849 ] ? mlx5_devlink_fs_mode_get+0x3b/0xa0
[ 385.119849 ] ? mlx5_devlink_fs_mode_get+0x3b/0xa0
[ 385.119849 ] kasan_report.cold+0x83/0xdf
[ 385.119849 ] ? devlink_param_notify+0x20/0x190
[ 385.119849 ] ? mlx5_devlink_fs_mode_get+0x3b/0xa0
[ 385.119849 ] mlx5_devlink_fs_mode_get+0x3b/0xa0
[ 385.119849 ] devlink_nl_param_fill+0x18a/0xa50
[ 385.119849 ] ? _raw_spin_lock_irqsave+0x8d/0xe0
[ 385.119849 ] ? devlink_flash_update_timeout_notify+0xf0/0xf0
[ 385.119849 ] ? __wake_up_common+0x4b/0x1e0
[ 385.119849 ] ? preempt_count_sub+0x14/0xc0
[ 385.119849 ] ? _raw_spin_unlock_irqrestore+0x28/0x40
[ 385.119849 ] ? __wake_up_common_lock+0xe3/0x140
[ 385.119849 ] ? __wake_up_common+0x1e0/0x1e0
[ 385.119849 ] ? __sanitizer_cov_trace_const_cmp8+0x27/0x80
[ 385.119849 ] ? __rcu_read_unlock+0x48/0x70
[ 385.119849 ] ? kasan_unpoison+0x23/0x50
[ 385.119849 ] ? __kasan_slab_alloc+0x2c/0x80
[ 385.119849 ] ? memset+0x20/0x40
[ 385.119849 ] ? __sanitizer_cov_trace_const_cmp4+0x25/0x80
[ 385.119849 ] devlink_param_notify+0xce/0x190
[ 385.119849 ] devlink_unregister+0x92/0x2b0
[ 385.119849 ] remove_one+0x41/0x140
[ 385.119849 ] pci_device_remove+0x68/0x140
[ 385.119849 ] ? pcibios_free_irq+0x10/0x10
[ 385.119849 ] __device_release_driver+0x294/0x3f0
[ 385.119849 ] device_driver_detach+0x82/0x130
[ 385.119849 ] unbind_store+0x193/0x1b0
[ 385.119849 ] ? subsys_interface_unregister+0x270/0x270
[ 385.119849 ] drv_attr_store+0x4e/0x70
[ 385.119849 ] ? drv_attr_show+0x60/0x60
[ 385.119849 ] sysfs_kf_write+0xa7/0xc0
[ 385.119849 ] kernfs_fop_write_iter+0x23a/0x2f0
[ 385.119849 ] ? sysfs_kf_bin_read+0x160/0x160
[ 385.119849 ] new_sync_write+0x311/0x430
[ 385.119849 ] ? new_sync_read+0x480/0x480
[ 385.119849 ] ? _raw_spin_lock+0x87/0xe0
[ 385.119849 ] ? __sanitizer_cov_trace_cmp4+0x25/0x80
[ 385.119849 ] ? security_file_permission+0x94/0xa0
[ 385.119849 ] vfs_write+0x4c7/0x590
[ 385.119849 ] ksys_write+0xf6/0x1e0
[ 385.119849 ] ? __x64_sys_read+0x50/0x50
[ 385.119849 ] ? fpregs_assert_state_consistent+0x99/0xa0
[ 385.119849 ] do_syscall_64+0x3d/0x90
[ 385.119849 ] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 385.119849 ] RIP: 0033:0x7fc36ef38504
[ 385.119849 ] Code: 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b3 0f 1f
80 00 00 00 00 48 8d 05 f9 61 0d 00 8b 00 85 c0 75 13 b8 01 00 00 00 0f
05 <48> 3d 00 f0 ff ff 77 54 c3 0f 1f 00 41 54 49 89 d4 55 48 89 f5 53
[ 385.119849 ] RSP: 002b:00007ffde0ff3d08 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[ 385.119849 ] RAX: ffffffffffffffda RBX: 000000000000000c RCX: 00007fc36ef38504
[ 385.119849 ] RDX: 000000000000000c RSI: 00007fc370521040 RDI: 0000000000000001
[ 385.119849 ] RBP: 00007fc370521040 R08: 00007fc36f00b8c0 R09: 00007fc36ee4b740
[ 385.119849 ] R10: 0000000000000000 R11: 0000000000000246 R12: 00007fc36f00a760
[ 385.119849 ] R13: 000000000000000c R14: 00007fc36f005760 R15: 000000000000000c
[ 385.119849 ] </TASK>
[ 385.119849 ]
[ 385.119849 ] Allocated by task 65:
[ 385.119849 ] kasan_save_stack+0x1e/0x40
[ 385.119849 ] __kasan_kmalloc+0x81/0xa0
[ 385.119849 ] mlx5_init_fs+0x11b/0x1160
[ 385.119849 ] mlx5_load+0x13c/0x220
[ 385.119849 ] mlx5_load_one+0xda/0x160
[ 385.119849 ] mlx5_recover_device+0xb8/0x100
[ 385.119849 ] mlx5_health_try_recover+0x2f9/0x3a1
[ 385.119849 ] devlink_health_reporter_recover+0x75/0x100
[ 385.119849 ] devlink_health_report+0x26c/0x4b0
[ 385.275909 ] mlx5_fw_fatal_reporter_err_work+0x11e/0x1b0
[ 385.275909 ] process_one_work+0x520/0x970
[ 385.275909 ] worker_thread+0x378/0x950
[ 385.275909 ] kthread+0x1bb/0x200
[ 385.275909 ] ret_from_fork+0x1f/0x30
[ 385.275909 ]
[ 385.275909 ] Freed by task 65:
[ 385.275909 ] kasan_save_stack+0x1e/0x40
[ 385.275909 ] kasan_set_track+0x21/0x30
[ 385.275909 ] kasan_set_free_info+0x20/0x30
[ 385.275909 ] __kasan_slab_free+0xfc/0x140
[ 385.275909 ] kfree+0xa5/0x3b0
[ 385.275909 ] mlx5_unload+0x2e/0xb0
[ 385.275909 ] mlx5_unload_one+0x86/0xb0
[ 385.275909 ] mlx5_fw_fatal_reporter_err_work.cold+0xca/0xcf
[ 385.275909 ] process_one_work+0x520/0x970
[ 385.275909 ] worker_thread+0x378/0x950
[ 385.275909 ] kthread+0x1bb/0x200
[ 385.275909 ] ret_from_fork+0x1f/0x30
[ 385.275909 ]
[ 385.275909 ] The buggy address belongs to the object at ffff888104b79300
[ 385.275909 ] which belongs to the cache kmalloc-128 of size 128
[ 385.275909 ] The buggy address is located 8 bytes inside of
[ 385.275909 ] 128-byte region [ffff888104b79300, ffff888104b79380)
[ 385.275909 ] The buggy address belongs to the page:
[ 385.275909 ] page:00000000de44dd39 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x104b78
[ 385.275909 ] head:00000000de44dd39 order:1 compound_mapcount:0
[ 385.275909 ] flags: 0x8000000000010200(slab|head|zone=2)
[ 385.275909 ] raw: 8000000000010200 0000000000000000 dead000000000122 ffff8881000428c0
[ 385.275909 ] raw: 0000000000000000 0000000080200020 00000001ffffffff 0000000000000000
[ 385.275909 ] page dumped because: kasan: bad access detected
[ 385.275909 ]
[ 385.275909 ] Memory state around the buggy address:
[ 385.275909 ] ffff888104b79200: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 fc fc
[ 385.275909 ] ffff888104b79280: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 385.275909 ] >ffff888104b79300: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 385.275909 ] ^
[ 385.275909 ] ffff888104b79380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 385.275909 ] ffff888104b79400: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 385.275909 ]]
Fixes: e890acd5ff18 ("net/mlx5: Add devlink flow_steering_mode parameter")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
In order to support multiple destination FTEs with SW steering
FW table is created with single FTE with multiple actions and
SW steering rule forward to it. When creating this table, flow
source isn't set according to the original FTE.
Fix this by passing the original FTE flow source to the created
FW table.
Fixes: 34583beea4b7 ("net/mlx5: DR, Create multi-destination table for SW-steering use")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
There are sleep in atomic context bugs when the request to secure
element of st-nci is timeout. The root cause is that nci_skb_alloc
with GFP_KERNEL parameter is called in st_nci_se_wt_timeout which is
a timer handler. The call paths that could trigger bugs are shown below:
(interrupt context 1)
st_nci_se_wt_timeout
nci_hci_send_event
nci_hci_send_data
nci_skb_alloc(..., GFP_KERNEL) //may sleep
(interrupt context 2)
st_nci_se_wt_timeout
nci_hci_send_event
nci_hci_send_data
nci_send_data
nci_queue_tx_data_frags
nci_skb_alloc(..., GFP_KERNEL) //may sleep
This patch changes allocation mode of nci_skb_alloc from GFP_KERNEL to
GFP_ATOMIC in order to prevent atomic context sleeping. The GFP_ATOMIC
flag makes memory allocation operation could be used in atomic context.
Fixes: ed06aeefdac3 ("nfc: st-nci: Rename st21nfcb to st-nci")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220517012530.75714-1-duoming@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
test_bit() tests if one bit is set or not.
Here the logic seems to check of bit QL_RESET_PER_SCSI (i.e. 4) OR bit
QL_RESET_START (i.e. 3) is set.
In fact, it checks if bit 7 (4 | 3 = 7) is set, that is to say
QL_ADAPTER_UP.
This looks harmless, because this bit is likely be set, and when the
ql_reset_work() delayed work is scheduled in ql3xxx_isr() (the only place
that schedule this work), QL_RESET_START or QL_RESET_PER_SCSI is set.
This has been spotted by smatch.
Fixes: 5a4faa873782 ("[PATCH] qla3xxx NIC driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/80e73e33f390001d9c0140ffa9baddf6466a41a2.1652637337.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Avoid putting Elo i2 PCIe Ports in D3cold because downstream devices
are inaccessible after going back to D0 (Rafael J. Wysocki)
- Qualcomm SM8250 has a ddrss_sf_tbu clock but SC8180X does not; make a
SC8180X-specific config without the clock so it probes correctly
(Bjorn Andersson)
- Revert aardvark chained IRQ handler rewrite because it broke
interrupt affinity (Pali Rohár)
* tag 'pci-v5.18-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "PCI: aardvark: Rewrite IRQ code to chained IRQ handler"
PCI: qcom: Remove ddrss_sf_tbu clock from SC8180X
PCI/PM: Avoid putting Elo i2 PCIe Ports in D3cold
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control fix from Rafael Wysocki:
"Fix up a recent change in the int340x thermal driver that
inadvertently broke thermal zone handling on some systems
(Srinivas Pandruvada)"
* tag 'thermal-5.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: int340x: Mode setting with new OS handshake
|
|
The code attempts to free the 'new' pointer using kmem_cache_free(),
which is wrong because this function isn't responsible of freeing it.
Instead, the function should free new->htable and clear the contents of
*new (to prevent double-free).
Cc: stable@vger.kernel.org
Fixes: c7c556f1e81b ("selinux: refactor changing booleans")
Reported-by: Wander Lairson Costa <wander@redhat.com>
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
