| Age | Commit message (Collapse) | Author |
|---|
|
Pull MIPS fixes from Ralf Baechle:
"The final round of fixes. One corner case in the math emulator and
another one in the mcount function for ftrace"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: mcount: Adjust stack pointer for static trace in MIPS32
MIPS: Fix MFC1 & MFHC1 emulation for 64-bit MIPS systems
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"This has:
- EFI revert to fix a boot regression
- early_ioremap() fix for boot failure
- KASLR fix for possible boot failures
- EFI fix for corrupted string printing
- remove a misleading EFI bootup 'failed!' error message
Unfortunately it's all rather close to the merge window"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/efi: Truncate 64-bit values when calling 32-bit OutputString()
x86/efi: Delete misleading efi_printk() error message
Revert "efi/x86: efistub: Move shared dependencies to <asm/efi.h>"
x86/kaslr: Avoid the setup_data area when picking location
x86 early_ioremap: Increase FIX_BTMAPS_SLOTS to 8
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fix from Dmitry Torokhov:
"A small fixup to i8042 adding Asus X450LCP to the nomux list"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - fix Asus X450LCP touchpad detection
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"A CONFIG_STACK_GROWSUP=y fix, and a hotplug llc CPU mask fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Fix unreleased llc_shared_mask bit during CPU hotplug
sched: Fix end_of_stack() and location of stack canary for architectures using CONFIG_STACK_GROWSUP
|
|
Merge fixes from Andrew Morton:
"9 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: softdirty: keep bit when zapping file pte
fs/cachefiles: add missing \n to kerror conversions
genalloc: fix device node resource counter
drivers/rtc/rtc-efi.c: add missing module alias
mm, slab: initialize object alignment on cache creation
mm: softdirty: addresses before VMAs in PTE holes aren't softdirty
ocfs2/dlm: do not get resource spinlock if lockres is new
nilfs2: fix data loss with mmap()
ocfs2: free vol_label in ocfs2_delete_osb()
|
|
This fixes the same bug as b43790eedd31 ("mm: softdirty: don't forget to
save file map softdiry bit on unmap") and 9aed8614af5a ("mm/memory.c:
don't forget to set softdirty on file mapped fault") where the return
value of pte_*mksoft_dirty was being ignored.
To be sure that no other pte/pmd "mk" function return values were being
ignored, I annotated the functions in arch/x86/include/asm/pgtable.h
with __must_check and rebuilt.
The userspace effect of this bug is that the softdirty mark might be
lost if a file mapped pte get zapped.
Signed-off-by: Peter Feiner <pfeiner@google.com>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Jamie Liu <jamieliu@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: <stable@vger.kernel.org> [3.12+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 0227d6abb378 ("fs/cachefiles: replace kerror by pr_err") didn't
include newline featuring in original kerror definition
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Reported-by: David Howells <dhowells@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: <stable@vger.kernel.org> [3.16.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Decrement the np_pool device_node refcount, which was incremented on
the preceding of_parse_phandle() call.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Without proper alias kernel module is not loaded for rtc-efi driver.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Cc: dann frazier <dannf@dannf.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since commit 4590685546a3 ("mm/sl[aou]b: Common alignment code"), the
"ralign" automatic variable in __kmem_cache_create() may be used as
uninitialized.
The proper alignment defaults to BYTES_PER_WORD and can be overridden by
SLAB_RED_ZONE or the alignment specified by the caller.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=85031
Signed-off-by: David Rientjes <rientjes@google.com>
Reported-by: Andrei Elovikov <a.elovikov@gmail.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In PTE holes that contain VM_SOFTDIRTY VMAs, unmapped addresses before
VM_SOFTDIRTY VMAs are reported as softdirty by /proc/pid/pagemap. This
bug was introduced in commit 68b5a6524856 ("mm: softdirty: respect
VM_SOFTDIRTY in PTE holes"). That commit made /proc/pid/pagemap look at
VM_SOFTDIRTY in PTE holes but neglected to observe the start of VMAs
returned by find_vma.
Tested:
Wrote a selftest that creates a PMD-sized VMA then unmaps the first
page and asserts that the page is not softdirty. I'm going to send the
pagemap selftest in a later commit.
Signed-off-by: Peter Feiner <pfeiner@google.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Jamie Liu <jamieliu@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There is a deadlock case which reported by Guozhonghua:
https://oss.oracle.com/pipermail/ocfs2-devel/2014-September/010079.html
This case is caused by &res->spinlock and &dlm->master_lock
misordering in different threads.
It was introduced by commit 8d400b81cc83 ("ocfs2/dlm: Clean up refmap
helpers"). Since lockres is new, it doesn't not require the
&res->spinlock. So remove it.
Fixes: 8d400b81cc83 ("ocfs2/dlm: Clean up refmap helpers")
Signed-off-by: Joseph Qi <joseph.qi@huawei.com>
Reviewed-by: joyce.xue <xuejiufei@huawei.com>
Reported-by: Guozhonghua <guozhonghua@h3c.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This bug leads to reproducible silent data loss, despite the use of
msync(), sync() and a clean unmount of the file system. It is easily
reproducible with the following script:
----------------[BEGIN SCRIPT]--------------------
mkfs.nilfs2 -f /dev/sdb
mount /dev/sdb /mnt
dd if=/dev/zero bs=1M count=30 of=/mnt/testfile
umount /mnt
mount /dev/sdb /mnt
CHECKSUM_BEFORE="$(md5sum /mnt/testfile)"
/root/mmaptest/mmaptest /mnt/testfile 30 10 5
sync
CHECKSUM_AFTER="$(md5sum /mnt/testfile)"
umount /mnt
mount /dev/sdb /mnt
CHECKSUM_AFTER_REMOUNT="$(md5sum /mnt/testfile)"
umount /mnt
echo "BEFORE MMAP:\t$CHECKSUM_BEFORE"
echo "AFTER MMAP:\t$CHECKSUM_AFTER"
echo "AFTER REMOUNT:\t$CHECKSUM_AFTER_REMOUNT"
----------------[END SCRIPT]--------------------
The mmaptest tool looks something like this (very simplified, with
error checking removed):
----------------[BEGIN mmaptest]--------------------
data = mmap(NULL, file_size - file_offset, PROT_READ | PROT_WRITE,
MAP_SHARED, fd, file_offset);
for (i = 0; i < write_count; ++i) {
memcpy(data + i * 4096, buf, sizeof(buf));
msync(data, file_size - file_offset, MS_SYNC))
}
----------------[END mmaptest]--------------------
The output of the script looks something like this:
BEFORE MMAP: 281ed1d5ae50e8419f9b978aab16de83 /mnt/testfile
AFTER MMAP: 6604a1c31f10780331a6850371b3a313 /mnt/testfile
AFTER REMOUNT: 281ed1d5ae50e8419f9b978aab16de83 /mnt/testfile
So it is clear, that the changes done using mmap() do not survive a
remount. This can be reproduced a 100% of the time. The problem was
introduced in commit 136e8770cd5d ("nilfs2: fix issue of
nilfs_set_page_dirty() for page at EOF boundary").
If the page was read with mpage_readpage() or mpage_readpages() for
example, then it has no buffers attached to it. In that case
page_has_buffers(page) in nilfs_set_page_dirty() will be false.
Therefore nilfs_set_file_dirty() is never called and the pages are never
collected and never written to disk.
This patch fixes the problem by also calling nilfs_set_file_dirty() if the
page has no buffers attached to it.
[akpm@linux-foundation.org: s/PAGE_SHIFT/PAGE_CACHE_SHIFT/]
Signed-off-by: Andreas Rohner <andreas.rohner@gmx.net>
Tested-by: Andreas Rohner <andreas.rohner@gmx.net>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
osb->vol_label is malloced in ocfs2_initialize_super but not freed if
error occurs or during umount, thus causing a memory leak.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com>
Reviewed-by: joyce.xue <xuejiufei@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Every mcount() call in the MIPS 32-bit kernel is done as follows:
[...]
move at, ra
jal _mcount
addiu sp, sp, -8
[...]
but upon returning from the mcount() function, the stack pointer
is not adjusted properly. This is explained in details in 58b69401c797
(MIPS: Function tracer: Fix broken function tracing).
Commit ad8c396936e3 ("MIPS: Unbreak function tracer for 64-bit kernel.)
fixed the stack manipulation for 64-bit but it didn't fix it completely
for MIPS32.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7792/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Commit bbd426f542cb "MIPS: Simplify FP context access" modified the
SIFROMREG & SIFROMHREG macros such that they return unsigned rather
than signed 32b integers. I had believed that to be fine, but
inadvertently missed the MFC1 & MFHC1 cases which write to a struct
pt_regs regs element. On MIPS32 this is fine, but on 64 bit those
saved regs' fields are 64 bit wide. Using unsigned values caused the
32 bit value from the FP register to be zero rather than sign extended
as the architecture specifies, causing incorrect emulation of the
MFC1 & MFHc1 instructions. Fix by reintroducing the casts to signed
integers, and therefore the sign extension.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: stable@vger.kernel.org # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7848/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are regression fixes (ACPI hotplug, cpufreq, hibernation, ACPI
LPSS driver), fixes for stuff that never worked correctly (ACPI GPIO
support in some cases and a wrong sign of an error code in the ACPI
core in one place), and one blacklist item for ACPI backlight
handling.
Specifics:
- Revert of a recent hibernation core commit that introduced a NULL
pointer dereference during resume for at least one user (Rafael J
Wysocki).
- Fix for the ACPI LPSS (Low-Power Subsystem) driver to disable
asynchronous PM callback execution for LPSS devices during system
suspend/resume (introduced in 3.16) which turns out to break
ordering expectations on some systems. From Fu Zhonghui.
- cpufreq core fix related to the handling of sysfs nodes during
system suspend/resume that has been broken for intel_pstate since
3.15 from Lan Tianyu.
- Restore the generation of "online" uevents for ACPI container
devices that was removed in 3.14, but some user space utilities
turn out to need them (Rafael J Wysocki).
- The cpufreq core fails to release a lock in an error code path
after changes made in 3.14. Fix from Prarit Bhargava.
- ACPICA and ACPI/GPIO fixes to make the handling of ACPI GPIO
operation regions (which means AML using GPIOs) work correctly in
all cases from Bob Moore and Srinivas Pandruvada.
- Fix for a wrong sign of the ACPI core's create_modalias() return
value in case of an error from Mika Westerberg.
- ACPI backlight blacklist entry for ThinkPad X201s from Aaron Lu"
* tag 'pm+acpi-3.17-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "PM / Hibernate: Iterate over set bits instead of PFNs in swsusp_free()"
gpio / ACPI: Use pin index and bit length
ACPICA: Update to GPIO region handler interface.
ACPI / platform / LPSS: disable async suspend/resume of LPSS devices
cpufreq: release policy->rwsem on error
cpufreq: fix cpufreq suspend/resume for intel_pstate
ACPI / scan: Correct error return value of create_modalias()
ACPI / video: disable native backlight for ThinkPad X201s
ACPI / hotplug: Generate online uevents for ACPI containers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"This is probably not the kind of pull request you want to see that
late in the cycle. Yet, the ACPI refactorization was problematic
again and caused another two issues which need fixing. My holidays
with limited internet (plus travelling) and the developer's illness
didn't help either :(
The details:
- ACPI code was refactored out into a seperate file and as a
side-effect, the i2c-core module got renamed. Jean Delvare
rightfully complained about the rename being problematic for
distributions. So, Mika and I thought the least problematic way to
deal with it is to move all the code back into the main i2c core
source file. This is mainly a huge code move with some #ifdeffery
applied. No functional code changes. Our personal tests and the
testbots did not find problems. (I was thinking about reverting,
too, yet that would also have ~800 lines changed)
- The new ACPI code also had a NULL pointer exception, thanks to
Peter for finding and fixing it.
- Mikko fixed a locking problem by decoupling clock_prepare and
clock_enable.
- Addy learnt that the datasheet was wrong and reimplemented the
frequency setup according to the new algorithm.
- Fan fixed an off-by-one error when copying data
- Janusz fixed a copy'n'paste bug which gave a wrong error message
- Sergei made sure that "don't touch" bits are not accessed"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: acpi: Fix NULL Pointer dereference
i2c: move acpi code back into the core
i2c: rk3x: fix divisor calculation for SCL frequency
i2c: mxs: fix error message in pio transfer
i2c: ismt: use correct length when copy buffer
i2c: rcar: fix RCAR_IRQ_ACK_{RECV|SEND}
i2c: tegra: Move clk_prepare/clk_set_rate to probe
|
|
Transfer Documentation maintainership to Jiri Kosina.
Thanks, Jiri.
I'll still be reviewing and working on documentation.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* pm-cpufreq:
cpufreq: release policy->rwsem on error
cpufreq: fix cpufreq suspend/resume for intel_pstate
* pm-sleep:
Revert "PM / Hibernate: Iterate over set bits instead of PFNs in swsusp_free()"
|
|
'acpi-video'
* acpi-hotplug:
ACPI / hotplug: Generate online uevents for ACPI containers
* acpi-scan:
ACPI / scan: Correct error return value of create_modalias()
* acpi-lpss:
ACPI / platform / LPSS: disable async suspend/resume of LPSS devices
* acpi-gpio:
gpio / ACPI: Use pin index and bit length
ACPICA: Update to GPIO region handler interface.
* acpi-video:
ACPI / video: disable native backlight for ThinkPad X201s
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio fixes from Linus Walleij:
"Two GPIO fixes:
- GPIO direction flags where handled wrong in the new descriptor-
based API, so direction changes did not always "take".
- Fix a handler installation race in the generic GPIO irqchip code"
* tag 'gpio-v3.17-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: Fix potential NULL handler data in chained irqchip handler
gpio: Fix gpio direction flags not getting set
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into x86/urgent
Pull EFI fixes from Matt Fleming:
* Revert the static library changes from the merge window since they're
causing issues for Macbooks and Fedora + Grub2 (Matt Fleming)
* Delete the misleading "setup_efi_pci() failed!" message which some
people are seeing when booting EFI (Matt Fleming)
* Fix printing strings from the 32-bit EFI boot stub by only passing
32-bit addresses to the firmware (Matt Fleming)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Pull devicetree bug fixes and documentation from Grant Likely:
"Several bug fix commits for issues found in the v3.17 rc series.
Most of these are minor in that they aren't actively dangerous, but
they have been seen in the wild. The one important fix is commit
7dbe5849fb50 ("of: make sure of_alias is initialized before accessing
it"), without which some powerpc platforms will fail to find stdout
for the console"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
of/fdt: fix memory range check
of: Fix memory block alignment in early_init_dt_add_memory_arch()
of: make sure of_alias is initialized before accessing it
of: Documentation regarding attaching OF Selftest testdata
of: Disabling OF functions that use sysfs if CONFIG_SYSFS disabled
of: correct of_console_check()'s return value
|
|
If adapter->dev.parent == NULL there is a NULL pointer dereference in
acpi_i2c_install_space_handler and acpi_i2c_remove_space_handler.
This is present since introduction of this code:
366047515c6e "i2c: rework kernel config I2C_ACPI" or even
da3c6647ee08 "I2C/ACPI: Clean up I2C ACPI code and Add CONFIG_I2C_ACPI"
The adapter->dev.parent == NULL case is valid for the i2c_stub,
so loading i2c_stub with ACPI_I2C_OPREGION enabled results in an oops.
This is also valid at least for i2c_tiny_usb and i2c_robotfuzz_osif.
Fix by checking whether it is null before calling ACPI_HANDLE.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Commit 5d98e61d337c ("I2C/ACPI: Add i2c ACPI operation region support")
renamed the i2c-core module. This may cause regressions for
distributions, so put the ACPI code back into the core.
Reported-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Lan Tianyu <tianyu.lan@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In cases where board has below memory DT node
memory{
device_type = "memory";
reg = <0x80000000 0x80000000>;
};
Check on the memory range in fdt.c will always fail because it is
comparing MAX_PHYS_ADDR with base + size, in fact it should compare
it with base + size - 1.
This issue was originally noticed on Qualcomm IFC6410 board.
Without this patch kernel shows up noticed unnecessary warnings
[ 0.000000] Machine model: Qualcomm APQ8064/IFC6410
[ 0.000000] Ignoring memory range 0xffffffff - 0x100000000
[ 0.000000] cma: Reserved 64 MiB at ab800000
as a result the size get reduced to 0x7fffffff which looks wrong.
This patch fixes the check involved in generating this warning and
as a result it also fixes the wrong size calculation.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
[grant.likely: adjust new size calculation also]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
|
We need to add this module to the nomux table to be able to detect the
touchpad.
Cc: stablevger.kernel.org
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Revert commit 6efde38f0769 (PM / Hibernate: Iterate over set bits
instead of PFNs in swsusp_free()) that introduced a NULL pointer
dereference during system resume from hibernation:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff810a8cc1>] swsusp_free+0x21/0x190
PGD b39c2067 PUD b39c1067 PMD 0
Oops: 0000 [#1] SMP
Modules linked in: <irrelevant list of modules>
CPU: 1 PID: 4898 Comm: s2disk Tainted: G C 3.17-rc5-amd64 #1 Debian 3.17~rc5-1~exp1
Hardware name: LENOVO 2776LEG/2776LEG, BIOS 6EET55WW (3.15 ) 12/19/2011
task: ffff88023155ea40 ti: ffff8800b3b14000 task.ti: ffff8800b3b14000
RIP: 0010:[<ffffffff810a8cc1>] [<ffffffff810a8cc1>]
swsusp_free+0x21/0x190
RSP: 0018:ffff8800b3b17ea8 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff8800b39bab00 RCX: 0000000000000001
RDX: ffff8800b39bab10 RSI: ffff8800b39bab00 RDI: 0000000000000000
RBP: 0000000000000010 R08: 0000000000000000 R09: 0000000000000000
R10: ffff8800b39bab10 R11: 0000000000000246 R12: ffffea0000000000
R13: ffff880232f485a0 R14: ffff88023ac27cd8 R15: ffff880232927590
FS: 00007f406d83b700(0000) GS:ffff88023bc80000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000000 CR3: 00000000b3a62000 CR4: 00000000000007e0
Stack:
ffff8800b39bab00 0000000000000010 ffff880232927590 ffffffff810acb4a
ffff8800b39bab00 ffffffff811a955a ffff8800b39bab10 0000000000000000
ffff88023155f098 ffffffff81a6b8c0 ffff88023155ea40 0000000000000007
Call Trace:
[<ffffffff810acb4a>] ? snapshot_release+0x2a/0xb0
[<ffffffff811a955a>] ? __fput+0xca/0x1d0
[<ffffffff81080627>] ? task_work_run+0x97/0xd0
[<ffffffff81012d89>] ? do_notify_resume+0x69/0xa0
[<ffffffff8151452a>] ? int_signal+0x12/0x17
Code: 66 2e 0f 1f 84 00 00 00 00 00 66 66 66 66 90 41 54 48 8b 05 ba 62 9c 00 49 bc 00 00 00 00 00 ea ff ff 48 8b 3d a1 62 9c 00 55 53 <48> 8b 10 48 89 50 18 48 8b 52 20 48 c7 40 28 00 00 00 00 c7 40
RIP [<ffffffff810a8cc1>] swsusp_free+0x21/0x190
RSP <ffff8800b3b17ea8>
CR2: 0000000000000000
---[ end trace f02be86a1ec0cccb ]---
due to forbidden_pages_map being NULL in swsusp_free().
Fixes: 6efde38f0769 "PM / Hibernate: Iterate over set bits instead of PFNs in swsusp_free()"
Reported-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull drm fixes from Dave Airlie:
"Some final radeon and i915 fixes, black screens mostly"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/cik: use a separate counter for CP init timeout
drm/i915/hdmi: fix hdmi audio state readout
drm/i915: Don't leak command parser tables on suspend/resume
drm/radeon: add PX quirk for asus K53TK
drm/radeon: add a backlight quirk for Amilo Xi 2550
drm/radeon: add a module parameter for backlight control (v2)
drm/radeon: Update IH_RB_RPTR register after each processed interrupt
drm/radeon: Make IH ring overflow debugging output more useful
drm/radeon: Clear RB_OVERFLOW bit earlier
|
|
Fix code when the operation region callback is for an gpio, which
is not at index 0 and for partial pins in a GPIO definition.
For example:
Name (GMOD, ResourceTemplate ()
{
//3 Outputs that define the Power mode of the device
GpioIo (Exclusive, PullDown, , , , "\\_SB.GPI2") {10, 11, 12}
})
}
If opregion callback calls is for:
- Set pin 10, then address = 0 and bit length = 1
- Set pin 11, then address = 1 and bit length = 1
- Set for both pin 11 and pin 12, then address = 1, bit length = 2
This change requires updated ACPICA gpio operation handler code to
send the pin index and bit length.
Fixes: 473ed7be0da0 (gpio / ACPI: Add support for ACPI GPIO operation regions)
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+: 75ec6e55f138 ACPICA: Update to GPIO region handler interface.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
If we're executing the 32-bit efi_char16_printk() code path (i.e.
running on top of 32-bit firmware) we know that efi_early->text_output
will be a 32-bit value, even though ->text_output has type u64.
Unfortunately, we currently pass ->text_output directly to
efi_early->call() so for CONFIG_X86_32 the compiler will push a 64-bit
value onto the stack, causing the other parameters to be misaligned.
The way we handle this in the rest of the EFI boot stub is to pass
pointers as arguments to efi_early->call(), which automatically do the
right thing (pointers are 32-bit on CONFIG_X86_32, and we simply ignore
the upper 32-bits of the argument register if running in 64-bit mode
with 32-bit firmware).
This fixes a corruption bug when printing strings from the 32-bit EFI
boot stub.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=84241
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
|
|
Changes to correct several GPIO issues:
1) The update_rule in a GPIO field definition is now ignored;
a read-modify-write operation is never performed for GPIO fields.
(Internally, this means that the field assembly/disassembly
code is completely bypassed for GPIO.)
2) The Address parameter passed to a GPIO region handler is
now the bit offset of the field from a previous Connection()
operator. Thus, it becomes a "Pin Number Index" into the
Connection() resource descriptor.
3) The bit_width parameter passed to a GPIO region handler is
now the exact bit width of the GPIO field. Thus, it can be
interpreted as "number of pins".
Overall, we can now say that the region handler interface
to GPIO handlers is a raw "bit/pin" addressed interface, not
a byte-addressed interface like the system_memory handler interface.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
into drm-fixes
- fix a backlight regression resulting in dark screen
- add a PX quirk to avoid a hang with runtime pm
- fix an init issue on the CIK compute rings
- fix IH ring buffer overflows gracefully
* 'drm-fixes-3.17' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon/cik: use a separate counter for CP init timeout
drm/radeon: add PX quirk for asus K53TK
drm/radeon: add a backlight quirk for Amilo Xi 2550
drm/radeon: add a module parameter for backlight control (v2)
drm/radeon: Update IH_RB_RPTR register after each processed interrupt
drm/radeon: Make IH ring overflow debugging output more useful
drm/radeon: Clear RB_OVERFLOW bit earlier
|
|
git://anongit.freedesktop.org/drm-intel into drm-fixes
a couple of small fixes for 3.17 still.
* tag 'drm-intel-fixes-2014-09-24' of git://anongit.freedesktop.org/drm-intel:
drm/i915/hdmi: fix hdmi audio state readout
drm/i915: Don't leak command parser tables on suspend/resume
|
|
On some systems (Asus T100 in particular) there are strict ordering
dependencies between LPSS devices with respect to power management
that break if they suspend/resume asynchronously.
In theory it should be possible to follow those dependencies in the
async suspend/resume case too (the ACPI tables tell as that the
dependencies are there), but since we're missing infrastructure
for that at the moment, disable async suspend/resume for all of
the LPSS devices for the time being.
Link: http://marc.info/?l=linux-acpi&m=141158962321905&w=2
Fixes: 8ce62f85a81f (ACPI / platform / LPSS: Enable async suspend/resume of LPSS devices)
Signed-off-by: Li Aubrey <aubrey.li@linux.intel.com>
Signed-off-by: Fu Zhonghui <zhonghui.fu@linux.intel.com>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull networking fixes from David Miller:
"Here is a quick pull request primarily meant to address the deconfig
fallout from changing SCSI_NETLINK from being used via 'select' to
being used via 'depends'.
I applied a set of 5 patches written by Michal Marek, and then I
carefully audited all of the remaining config files, basically:
1) I scanned every arch config file, and if it mentioned CONFIG_INET
or CONFIG_UNIX, I made sure it had CONFIG_NET=y
2) After that, I scanned every arch config file, and if it did not
have CONFIG_NET=y I made sure it did not reference any networking
config options.
Finally, we have some late breaking wireless fixes in here from John
Linville and co"
[ And there's a sparc bpf fix snuck in too ]
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
sparc: bpf_jit: fix loads from negative offsets
parisc: Update defconfigs which were missing CONFIG_NET.
powerpc: Update defconfigs which were missing CONFIG_NET.
s390: Update defconfigs which were missing CONFIG_NET.
mips: Update some more defconfigs which were missing CONFIG_NET.
sparc: Set CONFIG_NET=y in defconfigs
sh: Set CONFIG_NET=y in defconfigs
powerpc: Set CONFIG_NET=y in defconfigs
parisc: Set CONFIG_NET=y in defconfigs
mips: Set CONFIG_NET=y in defconfigs
brcmfmac: Fix off by one bug in brcmf_count_20mhz_channels()
ath9k: Fix NULL pointer dereference on early irq
net: rfkill: gpio: Fix clock status
NFC: st21nfca: Fix potential depmod dependency cycle
NFC: st21nfcb: Fix depmod dependency cycle
NFC: microread: Potential overflows in microread_target_discovered()
|
|
- fix BPF_LD|ABS|IND from negative offsets:
make sure to sign extend lower 32 bits in 64-bit register
before calling C helpers from JITed code, otherwise 'int k'
argument of bpf_internal_load_pointer_neg_helper() function
will be added as large unsigned integer, causing packet size
check to trigger and abort the program.
It's worth noting that JITed code for 'A = A op K' will affect
upper 32 bits differently depending whether K is simm13 or not.
Since small constants are sign extended, whereas large constants
are stored in temp register and zero extended.
That is ok and we don't have to pay a penalty of sign extension
for every sethi, since all classic BPF instructions have 32-bit
semantics and we only need to set correct upper bits when
transitioning from JITed code into C.
- though instructions 'A &= 0' and 'A *= 0' are odd, JIT compiler
should not optimize them out
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
pull request: wireless 2014-09-23
Please consider pulling this one last batch of fixes intended for the 3.17 stream!
For the NFC bits, Samuel says:
"Hopefully not too late for a handful of NFC fixes:
- 2 potential build failures for ST21NFCA and ST21NFCB, triggered by a
depmod dependenyc cycle.
- One potential buffer overflow in the microread driver."
On top of that...
Emil Goode provides a fix for a brcmfmac off-by-one regression which
was introduced in the 3.17 cycle.
Loic Poulain fixes a polarity mismatch for a variable assignment
inside of rfkill-gpio.
Wojciech Dubowik prevents a NULL pointer dereference in ath9k.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit df568d8e ("scsi: Use 'depends' with LIBFC instead of
'select'.") removed what happened to be the only instance of 'select
NET'. Defconfigs that were relying on the select now lack networking
support.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit df568d8e ("scsi: Use 'depends' with LIBFC instead of
'select'.") removed what happened to be the only instance of 'select
NET'. Defconfigs that were relying on the select now lack networking
support.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit df568d8e ("scsi: Use 'depends' with LIBFC instead of
'select'.") removed what happened to be the only instance of 'select
NET'. Defconfigs that were relying on the select now lack networking
support.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit df568d8e ("scsi: Use 'depends' with LIBFC instead of
'select'.") removed what happened to be the only instance of 'select
NET'. Defconfigs that were relying on the select now lack networking
support.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 5d6be6a5 ("scsi_netlink : Make SCSI_NETLINK dependent on NET
instead of selecting NET") removed what happened to be the only instance
of 'select NET'. Defconfigs that were relying on the select now lack
networking support.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: sparclinux@vger.kernel.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 5d6be6a5 ("scsi_netlink : Make SCSI_NETLINK dependent on NET
instead of selecting NET") removed what happened to be the only instance
of 'select NET'. Defconfigs that were relying on the select now lack
networking support.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: linux-sh@vger.kernel.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 5d6be6a5 ("scsi_netlink : Make SCSI_NETLINK dependent on NET
instead of selecting NET") removed what happened to be the only instance
of 'select NET'. Defconfigs that were relying on the select now lack
networking support.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 5d6be6a5 ("scsi_netlink : Make SCSI_NETLINK dependent on NET
instead of selecting NET") removed what happened to be the only instance
of 'select NET'. Defconfigs that were relying on the select now lack
networking support.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: linux-parisc@vger.kernel.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 5d6be6a5 ("scsi_netlink : Make SCSI_NETLINK dependent on NET
instead of selecting NET") removed what happened to be the only instance
of 'select NET'. Defconfigs that were relying on the select now lack
networking support.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: linux-mips@linux-mips.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull one last block fix from Jens Axboe:
"We've had an issue with scsi-mq where probing takes forever. This was
bisected down to the percpu changes for blk_mq_queue_enter(), and the
fact we now suffer an RCU grace period when killing a queue. SCSI
creates and destroys tons of queues, so this let to 10s of seconds of
stalls at boot for some.
Tejun has a real fix for this, but it's too involved for 3.17. So
this is a temporary workaround to expedite the queue killing until we
can fold in the real fix for 3.18 when that merge window opens"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq, percpu_ref: implement a kludge for SCSI blk-mq stall during probe
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Here are a few fixes that should be in v3.17.
- Reverting "Don't scan random busses" covers up a CardBus regression
having to do with allocating CardBus bus numbers.
- Reverting "Make sure bus numbers stay within parents bounds" covers
up an ACPI _CRS bug that makes us reconfigure a bridge, causing a
broken device behind it to stop responding.
- The pciehp timeout change fixes some code we added in v3.17.
Without the fix, we can send a new hotplug command too early,
before the timeout has expired.
I hope for better fixes for the reverts, but those will have to come
after v3.17"
* tag 'pci-v3.17-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: pciehp: Fix pcie_wait_cmd() timeout
Revert "PCI: Make sure bus number resources stay within their parents bounds"
Revert "PCI: Don't scan random busses in pci_scan_bridge()"
|
