| Age | Commit message (Collapse) | Author |
|---|
|
Move the DRRS debugfs stuff next to the actual implementation
so that it's easier to deal with the whole.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221003113249.16213-2-ville.syrjala@linux.intel.com
|
|
Make sure modes with crazy big dotclocks are rejected early,
so as to not cause problems for subsequent code via integer
overflows and whatnot.
These would eventually be rejected in intel_crtc_compute_pipe_mode()
but that is now too late as we do the clock computations a bit
earlier than that. And we don't want to just reorder the two since
we still want to check the final computed dotclock against the
hardware limit to make sure we didn't end up above the limit due
to rounding/etc.
Fixes: 0ff0e219d9b8 ("drm/i915: Compute clocks earlier")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220927182455.3422-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Replace the huge modifier lists in the watermark code with
a few calls to intel_fb.c.
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221003111544.8007-7-ville.syrjala@linux.intel.com
|
|
Take the DG2 CCS+CC modifier into account when calculating the
watermarks. Othwerwise we'll calculate the watermarks thinking this
tile-4 modifier is linear.
The rc_surface part is actually a nop since that is not used
for any glk+ platform.
Cc: stable@vger.kernel.org
Fixes: 680025dcc400 ("drm/i915/dg2: Add support for DG2 clear color compression")
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221003111544.8007-6-ville.syrjala@linux.intel.com
|
|
Take the DG2 CCS modifiers into account when calculating the
watermarks. Othwerwise we'll calculate the watermarks thinking these
tile-4 modifiers are linear.
The rc_surface part is actually a nop since that is not used
for any glk+ platform.
Cc: stable@vger.kernel.org
Fixes: 4c3afa72138c ("drm/i915/dg2: Add support for DG2 render and media compression")
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221003111544.8007-5-ville.syrjala@linux.intel.com
|
|
Take the gen12+ CCS+CC modifier into account when calculating the
watermarks. Othwerwise we'll calculate the watermarks thinking this
Y-tiled modifier is linear.
The rc_surface part is actually a nop since that is not used
for any glk+ platform.
Cc: stable@vger.kernel.org
Fixes: d1e2775e9b96 ("drm/i915/tgl: Add Clear Color support for TGL Render Decompression")
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221003111544.8007-4-ville.syrjala@linux.intel.com
|
|
Take the gen12+ MC CCS modifier into account when calculating the
watermarks. Othwerwise we'll calculate the watermarks thinking this
Y-tiled modifier is linear.
The rc_surface part is actually a nop since that is not used
for any glk+ platform.
v2: Split RC CCS vs. MC CCS to separate patches
Cc: stable@vger.kernel.org
Fixes: 2dfbf9d2873a ("drm/i915/tgl: Gen-12 display can decompress surfaces compressed by the media engine")
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221003111544.8007-3-ville.syrjala@linux.intel.com
|
|
Take the gen12+ RC CCS modifier into account when calculating the
watermarks. Othwerwise we'll calculate the watermarks thinking this
Y-tiled modifier is linear.
The rc_surface part is actually a nop since that is not used
for any glk+ platform.
v2: Split RC CCS vs. MC CCS to separate patches
Cc: stable@vger.kernel.org
Fixes: b3e57bccd68a ("drm/i915/tgl: Gen-12 render decompression")
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221003111544.8007-2-ville.syrjala@linux.intel.com
|
|
Current PSR code is supposed to use TRANSCODER_EDP to force 0 shift for
bits in PSR_IMR/IIR registers:
/*
* gen12+ has registers relative to transcoder and one per transcoder
* using the same bit definition: handle it as TRANSCODER_EDP to force
* 0 shift in bit definition
*/
At the time of writing the code assumption "TRANSCODER_EDP == 0" was made.
This is not the case and all fields in PSR_IMR and PSR_IIR are shifted
incorrectly if DISPLAY_VER >= 12.
Fix this by adding separate register field defines for >=12 and add bit
getter functions to keep code readability.
v4:
- Remove EDP from TGL definitions (José)
- Use REG_BIT and REG_GENMASK (José)
v3:
- Add separate register field defines (José)
- Add bit getter functions (José)
v2:
- Improve commit message (José)
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Fixes: 8241cfbe67f4 ("drm/i915/tgl: Access the right register when handling PSR interruptions")
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221003072011.72408-1-jouni.hogander@intel.com
|
|
Print out on which pipes, and for what reason, we are forcing a
full modeset.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220928060813.23264-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Make glk_load_degamma_lut() more like most everyone else and
pass in the LUT explicitly.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220929071521.26612-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Remove a bunch of pointless curly brackets and do
the s/dev_priv/i915/ while at it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220929071521.26612-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Get rid of the funny hsw vs. ivb extra indentation level in
intel_color_init_hooks().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220929071521.26612-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
intel_color_init() does both device level and crtc level stuff.
Split it up accordingly.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220929071521.26612-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
.load_luts() potentially runs from the vblank worker, and is
under a deadline to complete within the vblank. Thus we can't
do expesive stuff like talk to the Punit, etc.
To that end get rid of the assert_dsi_pll_enabled() call for
vlv/chv. We'll just have to trust that the PLL is already enabled
here.
And I don't think the normal assert_pll_enabled() really buys us
anything useful on gmch platforms either, so nuke that one too.
We don't have corresponding asserts in the ilk+ codepaths anyway
despite the hardware (IIRC) still requiring the clock to be
enabled when we access the LUT.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220929071521.26612-2-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
|
|
As with eDP let's stop considering the VBTs DRRS knobs and
just always accept all otherwise suitable EDID modes. This
appears to be how Windows does it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220927180615.25476-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Stop considering VBT's static DRRS support when deciding whether
to use alternate fixed modes or not. It looks like Windows more
or less just uses that to decide whether to automagically switch
refresh rates on AC<->battery changes, or perhaps whether to
even expose a control for that in some UI thing. Either way it
seems happy to always use all EDID modes, and I guess the
DRRS/VRR stuff more or less adjusts how said modes get
actually used.
Let's do the same and just accept all the suitable looking
modes from EDID, whether we have DRRS or VRR.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/6323
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/6484
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220927180615.25476-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Since commit a5810f551d0a ("drm/i915: Allow more varied alternate
fixed modes for panels") intel_panel_add_edid_alt_fixed_modes()
no longer considers vrr vs. drrs separately. So no reason to
pass them as separate parameters either.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220927180615.25476-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Add firmware status using a drm_warn when ARB session fails
or else a drm_dbg when the ARB session register slot bit did
get set.
Signed-off-by: Alan Previn <alan.previn.teres.alexis@intel.com>
Reviewed-by: Juston Li <justonli@chromium.org>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220923064542.415252-2-alan.previn.teres.alexis@intel.com
|
|
On pre-ddi platforms we have slightly different code being
used for HDMI TMDS clock to dotclock conversion between the
state computation and state readout. Both of these need to
round the same way in order to not get a mismatch between
the computed and read out states. Fix up the rounding
direction in the readout path to match what is used during
state computation.
Another option would to just use intel_crtc_dotclock()
in the readout path as well, but I don't really want to
do that as the current code more accurately represents
how the hardware really works; The HDMI port register
defines whether we're actually outputting 8bpc or 12bpc
over HDMI, and the PIPECONF bpc setting just defines what
goes over FDI between the CPU and PCH. The fact that we
try to cram all that into a single pipe_bpp during state
computation is perhaps not entirely great...
Fixes: f2c9df101095 ("drm/i915: Round TMDS clock to nearest")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220926193021.23287-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
During system resume DP MST requires AUX to be working already before
the HW state readout of the given encoder. Since AUX requires the
encoder/PHY TypeC mode to be initialized, which atm only happens during
HW state readout, these AUX transfers can change the TypeC mode
incorrectly (disconnecting the PHY for an enabled encoder) and trigger
the state check WARNs in intel_tc_port_sanitize().
Fix this by initializing the TypeC mode earlier both during driver
loading and system resume and making sure that the mode can't change
until the encoder's state is read out. While at it add the missing
DocBook comments and rename
intel_tc_port_sanitize()->intel_tc_port_sanitize_mode() for consistency.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220922172148.2913088-1-imre.deak@intel.com
|
|
Each PLL knows its own ID so intel_get_shared_dpll_id() is
pointless. Get rid of it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220921122343.13061-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Initialize the dll.lock mutex whether or not we manage to
initialize the rest of the dpll mgr.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220921122343.13061-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Spew a WARN if we try to ref/unref the same DPLL multiple
times for the same pipe.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220921211525.10675-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
We currently have a debug message in intel_reference_shared_dpll()
but no counterpart in intel_unreference_shared_dpll(). Add one.
Switch to the [CRTC:...] notation for the pipe name while at it.
v2: Use drm_dbg_kms() instead of drm_dbg() (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220922191350.4303-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Do all the checks in intel_dp_initial_fastset_check() instead
of bailing out on the first condition that triggers.
This makes for better debug logs since we see all the reasons
why the full modeset computation is forced.
Also avoid the risk of someone accidentally adding a check
later in the function that would require connectors_changed=true
(ie. no fastset at all), but an earlier check may have already
bailed out with just mode_changed=true (ie. fastset is still
possible).
Pimp the debugs with the encoder id+name while at it.
v2: Call the return variable 'fastset' to convey its meaning
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220922191314.4252-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
We always allocate two DPLLs (TC and TBT) for TC ports. This
is because we can't know ahead of time wherher we need to put
the PHY into DP-Alt or TBT mode.
However during readout we can obviously only read out the state
of the DPLL that the port is actually using. Thus the state after
readout will not have both DPLLs populated.
We run into problems if during readout the TC port is in DP-Alt
mode, but we then perform a modeset on the port without going
through the full .compute_config() machinery, and during said
modeset the port cannot be switched back into DP-Alt mode and
we need to take the TBT fallback path. Such a modeset can
happen eg. due to cdclk reprogramming.
This wasn't a problem earlier because we did all the DPLL
calculations much later in the modeset. So even if flagged
a modeset very late we'd still have gone through the DPLL
calculations. But now all the DPLL calculations happen much
earlier and so we need to deal with it, or else we'll attempt
a modeset without a DPLL.
To guarantee that we always have both DPLLs fully cal/ulated
for TC ports force a full modeset computation during the
initial commit.
v2: Avoid bitwise operation on bool (Jani)
Call the return variable 'fastset' to convey its meaning
Reported-by: Lee Shawn C <shawn.c.lee@intel.com>
Fixes: b000abd3b3d2 ("drm/i915: Do .crtc_compute_clock() earlier")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220922191236.4194-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Commit 00c6cbfd4e8a ("drm/i915: move pipe_mask and cpu_transcoder_mask
to runtime info") moved the pipe_mask member from struct
intel_device_info to intel_runtime_info, but overlooked some of our
platforms initializing device info .display = {}. This is significant,
as pipe_mask is the single point of truth for a device having a display
or not; the platforms in question left pipe_mask to whatever was set for
the platforms they "inherit" from in the complex macro scheme we have.
Add new NO_DISPLAY macro initializing .__runtime.pipe_mask = 0, which
will cause the device info .display sub-struct to be zeroed in
intel_device_info_runtime_init(). A better solution (or simply audit of
proper use of HAS_DISPLAY() checks) is required before moving forward
with [1].
Also clear all the display related members in runtime info if there's no
display. The latter is a bit tedious, but it's for completeness at this
time, to ensure similar functionality as before.
[1] https://lore.kernel.org/r/dfda1bf67f02ceb07c280b7a13216405fd1f7a34.1660137416.git.jani.nikula@intel.com
Fixes: 00c6cbfd4e8a ("drm/i915: move pipe_mask and cpu_transcoder_mask to runtime info")
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Maarten Lankhort <maarten.lankhorst@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Acked-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220916082642.3451961-1-jani.nikula@intel.com
|
|
Let's not forget to mark the unused watermark levels as invalid
after the readout. The vlv/chv codepath has this but the g4x
didn't for some reason.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220622155452.32587-6-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
|
|
We can simplify the vlv watermark sanitation by reusing the
second half of vlv_compute_pipe_wm() to convert the sanitized
raw watermarks into the proper form to be used as the
optimal/intermediate watermarks.
Also to be consistent with normal watermark computation the sanitized
watermarks should be all 0 for any disabled plane. Previously we
zeroed out the watermarks only up to the level (ie. PM2/5/DVDFS)
that was enabled.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220622155452.32587-5-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
|
|
We can simplify the g4x watermark sanitation by reusing the
second half of g4x_compute_pipe_wm() to convert the sanitized
raw watermarks into the proper form to be used as the
optimal/intermediate watermarks.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220622155452.32587-4-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
|
|
Split vlv_compute_pipe_wm() into two halves. The first half computes
the new raw watermarks, and the second half munges those up into real
watermarks for the particular pipe.
We can reuse the second half for watermark sanitation as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220622155452.32587-3-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanslav.lisovskiy@intel.com>
|
|
Split g4x_compute_pipe_wm() into two halves. The first half computes
the new raw watermarks, and the second half munges those up into real
watermarks for the particular pipe.
We can reuse the second half for watermark sanitation as well.
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220622155452.32587-2-ville.syrjala@linux.intel.com
|
|
In the unlikely case of not finding a fixed mode don't register
the eDP connector. I think there are some places where we'd oops
if we didn't have a fixed mode for eDP so presumable this doesn't
typically happen. But better safe than sorry.
Also pimp the debugs with the encoder id+name. I think dumping
the encoder rather than the connector provides more information
here (eg. to match against the port information in the VBT).
We can also drop the extra check from intel_edp_add_properties().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220912111814.17466-14-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
All the connectors are zero initialized so no need to clear
the *_allowed flags we don't support. Only leave the ones we want
to set. And while at it switch to booleans instead of ints.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220912111814.17466-13-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Consolidate the scaling_mode property setup into a single
place.
The one slight complicateion here is that GMCH platforms can't
do the CENTER mode except on the LVDS port. But we can deal with
that by just checking the connector type.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220912111814.17466-12-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
We have an eDP specific intel_edp_add_properties() so move
the eDP scaling_mode property setup there from
intel_dp_add_properties().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220912111814.17466-11-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Move the LVDS connector property setup to a dedicated
function to depollute intel_lvds_init() a bit.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220912111814.17466-10-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Move the DP MST connector property setup into its own function
so it's not spread all over intel_dp_add_mst_connector().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220912111814.17466-9-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Pull all the TV connector property setup into its own neat function.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220912111814.17466-8-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Pull the eDP backlight setup into its own function. No
reason to pollute intel_edp_init_connector() with all
the mundane details.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220912111814.17466-7-ville.syrjala@linux.intel.com
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Most of our encoder type cast stuff already operates on
intel_encoder rather than drm_encoder. Switch to_lvds_encoder()
over as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220912111814.17466-6-ville.syrjala@linux.intel.com
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Most places that deal with output types already use BIT()
but a few places still use manual shifts. Convert the
stragglers over to BIT().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220912111814.17466-5-ville.syrjala@linux.intel.com
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Just return the thing directly from the switch statement.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220912111814.17466-4-ville.syrjala@linux.intel.com
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Drop the pointless middle man variable and just return the
correct thing directly. And while at it change the return
type to u32 since this is a register value we're returning.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220912111814.17466-3-ville.syrjala@linux.intel.com
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
No need for the 'procmon' variable here. Just return the correct
thing from the switch statement directly.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220912111814.17466-2-ville.syrjala@linux.intel.com
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Use *_hpd_invert() helpers whenever possible to isolate logic specific
to hotplug inversion from common HPD setup logic to improve readability
and maintainability of the source code.
While we only define dg1_hpd_invert() here, future platforms are likely
to have different hotplug inversion needs, thus it makes sense grouping
different implementations under a common suffix.
v2: Fix coding style and prefer to use small *_hdp_invert() helpers
instead of a generic one.
CC: Jani Nikula <jani.nikula@linux.intel.com>
CC: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220922164949.163985-1-gustavo.sousa@intel.com
|
|
The function parameter 'exclude' in funciton
i915_sw_fence_await_reservation() is not used.
Remove it.
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220922213916.12112-1-niranjana.vishwanathapura@intel.com
|
|
Expand the current stepping convention to accommodate the GMD
stepping info. Typically GMD step maps to letter stepping
by "A + step %4" and number to "A + step /4" i.e, GMD step
0 maps to STEP_A0, 1 to _A1, 2 to _A2, 3 to _A3, 4 to STEP_B0...
Future platforms might break this formulae and may require a table
mapping to decode GMD step compatible with the convention.
v2:
- Pass the updated ip version structure
v3:
- Skip using GMD to step table(MattR)
Cc: Balasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220916014648.1310346-3-radhakrishna.sripada@intel.com
|
|
Going forward, the hardware teams no longer consider new platforms to
have a "generation" in the way we've defined it for past platforms.
Instead, each IP block (graphics, media, display) will have their own
architecture major.minor versions and stepping ID's which should be read
directly from a register in the MMIO space.
Bspec: 63361, 64111
v2:
- Move the IP version readout to intel_device_info.c
- Convert the macro into a function
v3:
- Move subplatform init to runtime early init
- Cache runtime ver, release info to compare with hardware values.
- Use IP_VER for snaity check(MattR)
v4:
- Minor doccumentation changes.
- Normalize HAS_GMD_ID macro value.(JaniN)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220916014648.1310346-2-radhakrishna.sripada@intel.com
|
