| Age | Commit message (Collapse) | Author |
|---|
|
Instead of reading the MPTCP-level sequence number when sending DATA_FIN,
store the data in the subflow so it can be safely accessed when the
subflow TCP headers are written to the packet without the MPTCP-level
lock held. This also allows the MPTCP-level socket to close individual
subflows without closing the MPTCP connection.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MPTCP should wait for an active connection or skip sending depending on
the connection state, as TCP does. This happens before the possible
passthrough to a regular TCP sendmsg because the subflow's socket type
(MPTCP or TCP fallback) is not known until the connection is
complete. This is also relevent at disconnect time, where data should
not be sent in certain MPTCP-level connection states.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Parav Pandit says:
====================
devlink: Introduce devlink port flavour virtual
Currently PCI PF and VF devlink devices register their ports as
physical port in non-representors mode.
Introduce a new port flavour as virtual so that virtual devices can
register 'virtual' flavour to make it more clear to users.
An example of one PCI PF and 2 PCI virtual functions, each having
one devlink port.
$ devlink port show
pci/0000:06:00.0/1: type eth netdev ens2f0 flavour physical port 0
pci/0000:06:00.2/1: type eth netdev ens2f2 flavour virtual port 0
pci/0000:06:00.3/1: type eth netdev ens2f3 flavour virtual port 0
Patch summary:
Patch-1 Introduces new devlink port flavour 'virtual'.
Patch-2 Uses new flavour to register PCI VF virtual ports.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use newly introduce 'virtual' port flavour for devlink
port of PCI VF devlink device in non-representors mode.
While at it, remove recently introduced empty lines at end of the file.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently mlx5 PCI PF and VF devlink devices register their ports as
physical port in non-representors mode.
Introduce a new port flavour as virtual so that virtual devices can
register 'virtual' flavour to make it more clear to users.
An example of one PCI PF and 2 PCI virtual functions, each having
one devlink port.
$ devlink port show
pci/0000:06:00.0/1: type eth netdev ens2f0 flavour physical port 0
pci/0000:06:00.2/1: type eth netdev ens2f2 flavour virtual port 0
pci/0000:06:00.3/1: type eth netdev ens2f3 flavour virtual port 0
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using vim to edit the phylink documentation reveals some mistakes due
to the "invisible" pythonesque white space indentation that can't be
seen with other editors. Fix it.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Paul Blakey says:
====================
act_ct: Software offload of conntrack_in
This series adds software offload of connections with an established
ct state using the NF flow table offload infrastructure, so
once such flows are offloaded, they will not pass through conntrack
again, and instead act_ct will restore the conntrack info metadata
on the skb to the state it had on the offload event - established.
Act_ct maintains an FT instance per ct zone. Flow table entries
are created, per ct connection, when connections enter an established
state and deleted otherwise. Once an entry is created, the FT assumes
ownership of the entry, and manages it's aging.
On the datapath, first lookup the skb in the zone's FT before going
into conntrack, and if a matching flow is found, restore the conntrack
info metadata on the skb, and skip calling conntrack.
Note that this patchset is part of the connection tracking offload feature.
Hardware offload of connections with an established ct state series will follow
this one.
Changelog:
v1->v2:
Removed now unused netfilter patches
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Offload nf conntrack processing by looking up the 5-tuple in the
zone's flow table.
The nf conntrack module will process the packets until a connection is
in established state. Once in established state, the ct state pointer
(nf_conn) will be restored on the skb from a successful ft lookup.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a ft entry when connections enter an established state and delete
the connections when they leave the established state.
The flow table assumes ownership of the connection. In the following
patch act_ct will lookup the ct state from the FT. In future patches,
drivers will register for callbacks for ft add/del events and will be
able to use the information to offload the connections.
Note that connection aging is managed by the FT.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the NF flow tables infrastructure for CT offload.
Create a nf flow table per zone.
Next patches will add FT entries to this table, and do
the software offload.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a spelling mistake in a dev_warn message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Validate 100baseT1_Full to make this driver work with TJA1102 PHY.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The data pointers of ipv6 sysctl are set one by one which is hard to
maintain, especially with kconfig. This patch simplifies it by using
math to point the per net sysctls into the appropriate struct net,
just like what we did for ipv4.
Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding ethtool stats for when XDP transmitted packets overrun the TX
queue. This is recorded separately for XDP_TX and ndo_xdp_xmit. This
is an important aid for troubleshooting XDP based setups.
It is currently a known weakness and property of XDP that there isn't
any push-back or congestion feedback when transmitting frames via XDP.
It's easy to realise when redirecting from a higher speed link into a
slower speed link, or simply two ingress links into a single egress.
The situation can also happen when Ethernet flow control is active.
For testing the patch and provoking the situation to occur on my
Espressobin board, I configured the TX-queue to be smaller (434) than
RX-queue (512) and overload network with large MTU size frames (as a
larger frame takes longer to transmit).
Hopefully the upcoming XDP TX hook can be extended to provide insight
into these TX queue overflows, to allow programmable adaptation
strategies.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
More zero-length array transformations from Gustavo A. R. Silva.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sunil Goutham says:
====================
net: thunderx: Miscellaneous changes
This patchset has changes wrt driver performance optimization,
load time optimization. And a change to PCI device regiatration
table for timestamp device.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Across Cavium's ThunderX and Marvell's OcteonTx2 silicons
the PTP timestamping block's PCI device ID and vendor ID
have remained same but the HW architecture has changed.
Hence added PCI subsystem IDs to the device table to avoid
this driver from being probed on OcteonTx2 silicons.
Signed-off-by: Prakash Brahmajyosyula <bprakash@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace msleep() with usleep_range() as internally it uses hrtimers.
This will put a cap on maximum wait time.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the current RX RED/DROP levels of 192/184 for CQE_RX, when
packet incoming rate is high, LLC is getting polluted resulting
in more cache misses and higher latency in packet processing. This
slows down the whole process and performance loss. Hence reduced
the levels to 224/216 (ie for a CQ size of 1024, Rx pkts will be
red dropped or dropped when unused CQE are less than 128/160 respectively)
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sunil Goutham says:
====================
octeontx2: Flow control support and other misc changes
This patch series adds flow control support (802.3 pause frames) and
has other changes wrt generic admin function (AF) driver functionality.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently on the first check if the operation is still not
finished, the poll goes to sleep for 2-5 usecs. But if for
some reason (due to other priority stuff like interrupts etc) by
the time the poll wakes up the 10ms time is expired then we don't
check if operation is finished or not and return failure.
This patch modifies poll logic to check HW operation after sleep so
that the status is checked atleast twice.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bus mastering is enabled by firmware, but when this driver
is unbinded bus mastering gets disabled by the PCI subsystem
which results interrupts not working when driver is reloaded.
Hence set bus mastering everytime in probe().
Also
- Converted pci_set_dma_mask() and pci_set_consistent_dma_mask()
to dma_set_mask_and_coherent().
- Cleared transaction pending bit which gets set during
driver unbind due to clearing of bus mastering (ME bit).
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently there is no way for AF dependent drivers in
any domain to check if the AF driver is loaded. This
patch sets an ID for RVUM block which will automatically
reflects in PF/VFs discovery register which they can
check and defer their probe until AF is up.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For retrieving info like interface MAC addresses, packet
parser key extraction config etc currently a command
is sent to firmware and firmware which periodically polls
for commands, processes these and returns the info.
This is resulting in interface initialization taking lot
of time. To optimize this a memory region is shared between
firmware and this driver, firmware while booting puts
static info like these into that region for driver to
read directly without using commands.
With this
- Logic for retrieving packet parser extraction config
via commands is removed and repalced with using the
shared 'fwdata' structure.
- Now RVU MSIX vector address is also retrieved from this fwdata struct
instead of from CSR. Otherwise when kexec/kdump crash kernel loads
CSR will have a IOVA setup by primary kernel which impacts
RVU PF/VF's interrupts.
- Also added a mbox handler for PF/VF interfaces to retrieve their MAC
addresses from AF.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Rakesh Babu <rsaladi2@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added mailbox requests to retrieve backpressure IDs from AF and Aura,
CQ contexts are configured with these BPIDs. So that when resource
levels reach configured thresholds they assert backpressure on the
interface which is also mapped to same BPID.
Also added support to enable/disable pause frames generation via ethtool.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CGX LMAC, the physical interface can generate pause frames when
internal resources asserts backpressure due to exhaustion.
This patch configures CGX to generate 802.3 pause frames.
Also enabled processing of received pause frames on the line which
will assert backpressure on the internal transmit path.
Also added mailbox handlers for PF drivers to enable or disable
pause frames anytime.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Each of the interface receive channels can be backpressured by
resources upon exhaustion or reaching configured threshold levels.
Resources here are receive buffer queues (Auras) and pkt notification
descriptor queues (CQs). Resources and interface channels are mapped
using backpressure IDs (BPIDs).
HW supports upto 512 BPIDs, this patch divides these BPIDs statically
across CGX/LBK/SDP interfaces as follows.
BPIDs 0 - 191 are mapped to LMAC channels, 16 per LMAC.
BPIDs 192 - 255 are mapped to LBK channels.
BPIDs 256 - 511 are mapped to SDP channels.
Also did the needed basic configuration of BPIDs.
Added mbox handlers with which a PF device can request for a BPID which
it will use to configure Auras and CQs.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add constants for the used interrupts bits. This avoids the magic
number for MII_VSC85XX_INT_MASK_MASK.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'net-ethtool-Introduce-link_ksettings-API-for-virtual-network-devices'
Cris Forno says:
====================
net/ethtool: Introduce link_ksettings API for virtual network devices
This series provides an API for drivers of virtual network devices that
allows users to alter initial device speed and duplex settings to reflect
the actual capabilities of underlying hardware. The changes made include
a helper function ethtool_virtdev_set_link_ksettings, which is used to
retrieve alterable link settings. In addition, there is a new ethtool
function defined to validate those settings. These changes resolve code
duplication for existing virtual network drivers that have already
implemented this behavior. In the case of the ibmveth driver, this API is
used to provide this capability for the first time.
---
v7: - removed ethtool_validate_cmd function pointer parameter from
ethtool_virtdev_set_link_ksettings since none of the virtual drivers
pass in a custom validate function as suggested by Michal Kubecek.
v6: - removed netvsc_validate_ethtool_ss_cmd(). netvsc_drv now uses
ethtool_virtdev_validate_cmd() instead as suggested by Michal Kubecek
and approved by Haiyang Zhang.
- matched handler argument name of ethtool_virtdev_set_link_ksettings
in declaration and definition as suggested by Michal Kubecek.
- shortened validate variable assignment in
ethtool_virtdev_set_link_ksettings as suggested by Michal Kubecek.
v5: - virtdev_validate_link_ksettings is taken out of the ethtool global
structure and is instead added as an argument to
ethtool_virtdev_set_link_ksettings as suggested by Jakub Kicinski.
v4: - Cleaned up return statement in ethtool_virtdev_validate_cmd based
off of Michal Kubecek's and Thomas Falcon's suggestion.
- If the netvsc driver is using the VF device in order to get
accelerated networking, the real speed and duplex is reported by using
the VF device as suggested by Stephen Hemminger.
- The speed and duplex variables are now passed by value rather than
passed by pointer as suggested by Willem de Bruijin and Michal
Kubecek.
- Removed ethtool_virtdev_get_link_ksettings since it was too simple
to warrant a helper function.
v3: - Factored out duplicated code to core/ethtool to provide API to
virtual drivers
v2: - Updated default driver speed/duplex settings to avoid breaking
existing setups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
