| Age | Commit message (Collapse) | Author |
|---|
|
Pretty much any node can have a status property, so it doesn't need to
be in examples.
Converted with the following command and removed examples with SoC and
board specific splits:
git grep -l -E 'status.*=.*' Documentation/devicetree/ | xargs sed -i -E '/\sstatus.*=.*"(disabled|ok|okay)/d'
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
This reverts commit ab714817d7e891608d31f6996b1e4c43cf2bf342.
The original commit was designed to handle a bug in the trf7970a NFC
controller where an extra byte was returned in Read Multiple Blocks (RMB)
command responses. However, it has become less clear whether it is a bug
in the trf7970a or in the tag. In addition, it was assumed that the extra
byte was always returned but it turns out that is not always the case. The
result is that a byte of good data is trimmed off when the extra byte is
not present ultimately causing the neard deamon to fail the read.
Since the trf7970a driver does not have the context to know when to trim
the byte or not, remove the code from the trf7970a driver all together
(and move it up to the neard daemon). This has the added benefit of
simplifying the kernel driver and putting the extra complexity into
userspace.
CC: Rob Herring <robh@kernel.org>
CC: devicetree@vger.kernel.org
Signed-off-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The example DTS code for the trf7970a sets the GPIOs for the EN
and EN2 pins to active low when they are really active high so
correct the error.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The 'vin-voltage-override' DT property is used by the trf7970a
driver to override the voltage presented to the driver by the
regulator subsystem. This is unnecessary as properly specifying
the regulator chain via DT properties will accomplish the same
thing. Therefore, remove support for 'vin-voltage-override'.
Signed-off-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The TRF7970A has configuration options for supporting hardware designs
with 1.8 Volt or 3.3 Volt IO. This commit adds a device tree option,
using a fixed regulator binding, for setting the io voltage to match
the hardware configuration. If no option is supplied it defaults to
3.3 volt configuration.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Geoff Lansberry <geoff@kuvee.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The TRF7970A has configuration options to support hardware designs
which use a 27.12MHz clock. This commit adds a device tree option
'clock-frequency' to support configuring the this chip for default
13.56MHz clock or the optional 27.12MHz clock.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Geoff Lansberry <geoff@kuvee.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Make the EN2 pin optional. This is useful for boards,
which have this pin fix wired, for example to ground.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guan Ben <ben.guan@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Add pn533-i2c phy devicetree documentation
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch includes ST95HF binding doc that guides how to
make node entry of ST95HF in DT file of any platform.
Signed-off-by: Shikha Singh <shikha.singh@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Align NFC bindgins to use marvell instead of mrvl.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This driver adds the support of SPI-based Marvell NFC controller.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This driver adds the support of I2C-based Marvell NFC controller.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
In order to align with st21nfca, dts configuration properties
ese_present and uicc_present are made available in st-nci driver.
So far, in early development firmware, because
nci_nfcee_mode_set(DISABLE) was not supported we had to try to
enable it during the secure element discovery phase.
After several trials on commercial and qualified firmware it appears
that nci_nfcee_mode_set(ENABLE) and nci_nfcee_mode_set(DISABLE) are
properly supported.
Such feature also help us to eventually save some time (~5ms) when
only one secure element is connected.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Add driver for Samsung S3FWRN5 NFC controller.
S3FWRN5 is using NCI protocol and I2C communication interface.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Add st-nci-spi phy devicetree documentation
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Add support of Marvell NFC chip controlled over UART
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
STMicroelectronics NFC NCI chips family is extending
with the new ST21NFCC using the AMS AS39230 RF booster.
The st21nfcb driver is relevant for this solution and
might be with future products.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The current versions of the trf7970a has an erratum where it returns
an extra byte in the response to 'Read Multiple Block' (RMB) commands.
This command is issued to Type 5 tags (i.e., ISO/IEC 15693 tags) by
the neard daemon.
To handle this, define a new Device Tree property,
't5t-rmb-extra-byte-quirk', which indicates that the associated
trf7970a device has this erratum. The trf7970a device driver
will then ensure that the response length to RMB commands is
reduced by one byte (for devices with the erratum).
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Add a module to the NXP-NCI driver to support NFC controllers with an
I2C control interface, such as the NPC100.
Signed-off-by: Clément Perrochaud <clement.perrochaud@effinnov.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
On st21nfca, the mechanism to enable a secure element needs to add 2
properties in order manage the SWP line correctly.
Document ese-present and uicc-present properties.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Other drivers are following the following compatible string format for dts:
s/_/-/
Because some devices may still use the previous string, the new corrected
string is added to the of_device_id table.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Other drivers are following the following compatible string format for dts:
s/_/-/
Because some devices may still use the previous string, the new corrected
string is added to the of_device_id table.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
St21nfcb has a reverse polarity compare to st21nfca.
In st21nfcb case, the irq pin is active high.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Current versions of the trf7970a have an erratum where
the EN2 pin must be kept low. If it isn't kept low,
it will generate an RF field even when in passive
target mode. To work around this issue, create the
'en2-rf-quirk' device tree property to indicate that
the trf7970a that the driver is using has this erratum.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The mechanism for specifying that the trf7970a
being used by the driver has the "IRQ Status Read"
erratum has been changed to a device tree property
('irq-status-read-quirk').
Document the new device tree property.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The trf7970a driver recently had support for the
'vin-voltage-override' property added to it. This
property is used to override the value given by
the regulator subsystem for the VIN pin's voltage.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Describe the properties used by the st21nfcb NFC controller driver.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Replaced st,st21nfca-i2c by st,st21nfca_i2c to be concistent
with below configuration and driver in drivers/nfc/st21nfca/
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Describe the properties used by the st21nfca NFC controller driver.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The trf7970a driver recently had support added for the 'autosuspend-delay'
property so document it.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Describe the properties used by the PN544 NFC controller driver.
Signed-off-by: Clément Perrochaud <clement.perrochaud@nxp.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Describe the properies used by the trf7970a
RFID/NFC/15693 transceiver driver.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
