| Age | Commit message (Collapse) | Author |
|---|
|
Document the devicetree bindings in 8250.txt for MediaTek BTIF
controller which could be found on MT7622 and MT7623 SoC.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This adds the hooks for an optional reset controller in the 8250 device
tree node.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This change adds a driver for the 16550-based Aspeed virtual UART
device. We use a similar process to the of_serial driver for device
probe, but expose some VUART-specific functions through sysfs too.
The VUART is two UART 'front ends' connected by their FIFO (no actual
serial line in between). One is on the BMC side (management controller)
and one is on the host CPU side.
This driver is for the BMC side. The sysfs files allow the BMC
userspace, which owns the system configuration policy, to specify at
what IO port and interrupt number the host side will appear to the host
on the Host <-> BMC LPC bus. It could be different on a different system
(though most of them use 3f8/4).
OpenPOWER host firmware doesn't like it when the host-side of the
VUART's FIFO is not drained. This driver only disables host TX discard
mode when the port is in use. We set the VUART enabled bit when we bind
to the device, and clear it on unbind.
We don't want to do this on open/release, as the host may be using this
bit to configure serial output modes, which is independent of whether
the devices has been opened by BMC userspace.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This adds the ti,da830-uart compatible string to serial 8250 UART bindings.
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add the device tree binding needed to support the TX FIFO threshold
parameter.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Serial console is broken in v4.8-rcX. Mika and I independently bisected down to
commit 4ef03d328769 ("tty/serial/8250: use mctrl_gpio helpers").
Since neither author nor anyone else didn't propose a solution we better revert
it for now.
This reverts commit 4ef03d328769eddbfeca1f1c958fdb181a69c341.
Link: https://lkml.kernel.org/r/20160809130229.GN1729@lahna.fi.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch permits the usage for GPIOs to control
the CTS/RTS/DTR/DSR/DCD/RI signals.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
All users of QPACE have upgraded to QPACE2 so remove the Cell QPACE code.
Signed-off-by: Rashmica Gupta <rashmicy@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The file of-serial.txt was only for 8250 compatible UART implementations,
so renamed it to 8250.txt to avoid confusing other persons.
This is suggested by Arnd, see:
http://lists.infradead.org/pipermail/linux-arm-kernel/2014-September/291455.html
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
