| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Nothing special for the power-supply subystem this time.
- power-supply core: remove faulty cooling logic
- convert all sysfs show() handlers from *printf() use sysfs_emit()
- bq25890: add dual-charger support required by Lenovo Yoga Tab 3 Pro
- bq27xxx: fix reporting critical level
- syscon-reboot: add priority property support
- new rt9467 charger driver
- new rt9471 charger driver
- new Odroid Go Ultra poweroff driver
- misc minor fixes and cleanups"
* tag 'for-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (32 commits)
power: reset: odroid-go-ultra: fix I2C dependency
power: supply: leds: explicitly include linux/leds.h
dt-bindings: power: supply: pm8941-coincell: Don't require charging properties
dt-bindings: power: supply: pm8941-coincell: Add PM8998 compatible
power: reset: add Odroid Go Ultra poweroff driver
power: supply: rt9467: Fix spelling mistake "attache" -> "attach"
power: supply: rt9471: fix using wrong ce_gpio in rt9471_probe()
power: supply: max77650: Make max77650_charger_disable() return void
Documentation: power: rt9467: Document exported sysfs entries
power: supply: rt9467: Add Richtek RT9467 charger driver
dt-bindings: power: supply: Add Richtek RT9467 battery charger
Documentation: power: rt9471: Document exported sysfs entries
power: supply: rt9471: Add Richtek RT9471 charger driver
dt-bindings: power: supply: Add Richtek RT9471 battery charger
power: supply: max1721x: Use strscpy() is more robust and safer
power: supply: test-power: use strscpy() instead of strncpy()
power: supply: bq27xxx: fix reporting critical level
power: supply: bq256xx: Init ichg/vbat value with chip default value
power: supply: collie_battery: Convert to GPIO descriptors (part 2)
power: supply: remove faulty cooling logic
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Rework portdrv shutdown so it disables interrupts but doesn't
disable bus mastering, which leads to hangs on Loongson LS7A
- Add mechanism to prevent Max_Read_Request_Size (MRRS) increases,
again to avoid hardware issues on Loongson LS7A (and likely other
devices based on DesignWare IP)
- Ignore devices with a firmware (DT or ACPI) node that says the
device is disabled
Resource management:
- Distribute spare resources to unconfigured hotplug bridges at
boot-time (not just when hot-adding such a bridge), which makes
hot-adding devices to docks work better. Tried this in v6.1 but had
to revert for regressions, so try again
- Fix root bus issue that dropped resources that happened to end
at 0, e.g., [bus 00]
PCI device hotplug:
- Remove device locking when marking device as disconnected so this
doesn't have to wait for concurrent driver bind/unbind to complete
- Quirk more Qualcomm bridges that don't fully implement the PCIe
Slot Status 'Command Completed' bit
Power management:
- Account for _S0W of the target bridge in acpi_pci_bridge_d3() so we
don't miss hot-add notifications for USB4 docks, Thunderbolt, etc
Reset:
- Observe delay after reset, e.g., resuming from system sleep,
regardless of whether a bridge can suspend to D3cold at runtime
- Wait for secondary bus to become ready after a bridge reset
Virtualization:
- Avoid FLR on some AMD FCH AHCI adapters where it doesn't work
- Allow independent IOMMU groups for some Wangxun NICs that prevent
peer-to-peer transactions but don't advertise an ACS Capability
Error handling:
- Configure End-to-End-CRC (ECRC) only if Linux owns the AER
Capability
- Remove redundant Device Control Error Reporting Enable in the AER
service driver since this is already done for all devices during
enumeration
ASPM:
- Add pci_enable_link_state() interface to allow drivers to enable
ASPM link state
Endpoint framework:
- Move dra7xx and tegra194 linkup processing from hard IRQ to
threaded IRQ handler
- Add a separate lock for endpoint controller list of endpoint
function drivers to prevent deadlock in callbacks
- Pass events from endpoint controller to endpoint function drivers
via callbacks instead of notifiers
Synopsys DesignWare eDMA controller driver (acked by Vinod):
- Fix CPU vs PCI address issues
- Fix source vs destination address issues
- Fix issues with interleaved transfer semantics
- Fix channel count initialization issue (issue still exists in
several other drivers)
- Clean up and improve debugfs usage so it will work on platforms
with several eDMA devices
Baikal T-1 PCIe controller driver:
- Set a 64-bit DMA mask
Freescale i.MX6 PCIe controller driver:
- Add i.MX8MM, i.MX8MQ, i.MX8MP endpoint mode DT binding and driver
support
Intel VMD host bridge driver:
- Add quirk to configure PCIe ASPM and LTR. This is normally done by
BIOS, and will be for future products
Marvell MVEBU PCIe controller driver:
- Mark this driver as broken in Kconfig since bugs prevent its daily
usage
MediaTek MT7621 PCIe controller driver:
- Delay PHY port initialization to improve boot reliability for ZBT
WE1326, ZBT WF3526-P, and some Netgear models
Qualcomm PCIe controller driver:
- Add MSM8998 DT compatible string
- Unify MSM8996 and MSM8998 clock orderings
- Add SM8350 DT binding and driver support
- Add IPQ8074 Gen3 DT binding and driver support
- Correct qcom,perst-regs in DT binding
- Add qcom_pcie_host_deinit() so the PHY is powered off and
regulators and clocks are disabled on late host-init errors
Socionext UniPhier Pro5 controller driver:
- Clean up uniphier-ep reg, clocks, resets, and their names in DT
binding
Synopsys DesignWare PCIe controller driver:
- Restrict coherent DMA mask to 32 bits for MSI, but allow controller
drivers to set 64-bit streaming DMA mask
- Add eDMA engine support in both Root Port and Endpoint controllers
Miscellaneous:
- Remove MODULE_LICENSE from boolean drivers so they don't look like
modules so modprobe can complain about them"
* tag 'pci-v6.3-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (86 commits)
PCI: dwc: Add Root Port and Endpoint controller eDMA engine support
PCI: bt1: Set 64-bit DMA mask
PCI: dwc: Restrict only coherent DMA mask for MSI address allocation
dmaengine: dw-edma: Prepare dw_edma_probe() for builtin callers
dmaengine: dw-edma: Depend on DW_EDMA instead of selecting it
dmaengine: dw-edma: Add mem-mapped LL-entries support
PCI: Remove MODULE_LICENSE so boolean drivers don't look like modules
PCI: hv: Drop duplicate PCI_MSI dependency
PCI/P2PDMA: Annotate RCU dereference
PCI/sysfs: Constify struct kobj_type pci_slot_ktype
PCI: hotplug: Allow marking devices as disconnected during bind/unbind
PCI: pciehp: Add Qualcomm quirk for Command Completed erratum
PCI: qcom: Add IPQ8074 Gen3 port support
dt-bindings: PCI: qcom: Add IPQ8074 Gen3 port
dt-bindings: PCI: qcom: Sort compatibles alphabetically
PCI: qcom: Fix host-init error handling
PCI: qcom: Add SM8350 support
dt-bindings: PCI: qcom: Add SM8350
dt-bindings: PCI: qcom-ep: Correct qcom,perst-regs
dt-bindings: PCI: qcom: Unify MSM8996 and MSM8998 clock order
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- Consolidate iommu_map/unmap functions.
There have been blocking and atomic variants so far, but that was
problematic as this approach does not scale with required new
variants which just differ in the GFP flags used. So Jason
consolidated this back into single functions that take a GFP
parameter.
- Retire the detach_dev() call-back in iommu_ops
- Arm SMMU updates from Will:
- Device-tree binding updates:
- Cater for three power domains on SM6375
- Document existing compatible strings for Qualcomm SoCs
- Tighten up clocks description for platform-specific
compatible strings
- Enable Qualcomm workarounds for some additional platforms that
need them
- Intel VT-d updates from Lu Baolu:
- Add Intel IOMMU performance monitoring support
- Set No Execute Enable bit in PASID table entry
- Two performance optimizations
- Fix PASID directory pointer coherency
- Fix missed rollbacks in error path
- Cleanups
- Apple t8110 DART support
- Exynos IOMMU:
- Implement better fault handling
- Error handling fixes
- Renesas IPMMU:
- Add device tree bindings for r8a779g0
- AMD IOMMU:
- Various fixes for handling on SNP-enabled systems and
handling of faults with unknown request-ids
- Cleanups and other small fixes
- Various other smaller fixes and cleanups
* tag 'iommu-updates-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (71 commits)
iommu/amd: Skip attach device domain is same as new domain
iommu: Attach device group to old domain in error path
iommu/vt-d: Allow to use flush-queue when first level is default
iommu/vt-d: Fix PASID directory pointer coherency
iommu/vt-d: Avoid superfluous IOTLB tracking in lazy mode
iommu/vt-d: Fix error handling in sva enable/disable paths
iommu/amd: Improve page fault error reporting
iommu/amd: Do not identity map v2 capable device when snp is enabled
iommu: Fix error unwind in iommu_group_alloc()
iommu/of: mark an unused function as __maybe_unused
iommu: dart: DART_T8110_ERROR range should be 0 to 5
iommu/vt-d: Enable IOMMU perfmon support
iommu/vt-d: Add IOMMU perfmon overflow handler support
iommu/vt-d: Support cpumask for IOMMU perfmon
iommu/vt-d: Add IOMMU perfmon support
iommu/vt-d: Support Enhanced Command Interface
iommu/vt-d: Retrieve IOMMU perfmon capability information
iommu/vt-d: Support size of the register set in DRHD
iommu/vt-d: Set No Execute Enable bit in PASID table entry
iommu/vt-d: Remove sva from intel_svm_dev
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DT core:
- Add node lifecycle unit tests
- Add of_property_present() helper aligned with fwnode API
- Print more information on reserved regions on boot
- Update dtc to upstream v1.6.1-66-gabbd523bae6e
- Use strscpy() to instead of strncpy() in DT core
- Add option for schema validation on %.dtb targets
Bindings:
- Add/fix support for listing multiple patterns in DT_SCHEMA_FILES
- Rework external memory controller/bus bindings to properly support
controller specific child node properties
- Convert loongson,ls1x-intc, fcs,fusb302, sil,sii8620, Rockchip
RK3399 PCIe, Synquacer I2C, and Synquacer EXIU bindings to DT
schema format
- Add RiscV SBI PMU event mapping binding
- Add missing contraints on Arm SCMI child node allowed properties
- Add a bunch of missing Socionext UniPhier glue block bindings and
example fixes
- Various fixes for duplicate or conflicting type definitions on DT
properties"
* tag 'devicetree-for-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (66 commits)
dt-bindings: regulator: Add mps,mpq7932 power-management IC
of: dynamic: Fix spelling mistake "kojbect" -> "kobject"
dt-bindings: drop Sagar Kadam from SiFive binding maintainership
dt-bindings: sram: qcom,imem: document sm8450
dt-bindings: interrupt-controller: convert loongson,ls1x-intc.txt to json-schema
dt-bindings: arm: Add Cortex-A715 and X3
of: dynamic: add lifecycle docbook info to node creation functions
of: add consistency check to of_node_release()
of: do not use "%pOF" printk format on node with refcount of zero
of: unittest: add node lifecycle tests
of: update kconfig unittest help
of: add processing of EXPECT_NOT to of_unittest_expect
of: prepare to add processing of EXPECT_NOT to of_unittest_expect
of: Use preferred of_property_read_* functions
of: Use of_property_present() helper
of: Add of_property_present() helper
of: reserved_mem: Use proper binary prefix
dt-bindings: Fix multi pattern support in DT_SCHEMA_FILES
of: reserved-mem: print out reserved-mem details during boot
dt-bindings: serial: restrict possible child node names
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver subsystem updates from Greg KH:
"Here is the large set of driver changes for char/misc drivers and
other smaller driver subsystems that flow through this git tree.
Included in here are:
- New IIO drivers and features and improvments in that subsystem
- New hwtracing drivers and additions to that subsystem
- lots of interconnect changes and new drivers as that subsystem
seems under very active development recently. This required also
merging in the icc subsystem changes through this tree.
- FPGA driver updates
- counter subsystem and driver updates
- MHI driver updates
- nvmem driver updates
- documentation updates
- Other smaller driver updates and fixes, full details in the
shortlog
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (223 commits)
scripts/tags.sh: fix incompatibility with PCRE2
firmware: coreboot: Remove GOOGLE_COREBOOT_TABLE_ACPI/OF Kconfig entries
mei: lower the log level for non-fatal failed messages
mei: bus: disallow driver match while dismantling device
misc: vmw_balloon: fix memory leak with using debugfs_lookup()
nvmem: stm32: fix OPTEE dependency
dt-bindings: nvmem: qfprom: add IPQ8074 compatible
nvmem: qcom-spmi-sdam: register at device init time
nvmem: rave-sp-eeprm: fix kernel-doc bad line warning
nvmem: stm32: detect bsec pta presence for STM32MP15x
nvmem: stm32: add OP-TEE support for STM32MP13x
nvmem: core: use nvmem_add_one_cell() in nvmem_add_cells_from_of()
nvmem: core: add nvmem_add_one_cell()
nvmem: core: drop the removal of the cells in nvmem_add_cells()
nvmem: core: move struct nvmem_cell_info to nvmem-provider.h
nvmem: core: add an index parameter to the cell
of: property: add #nvmem-cell-cells property
of: property: make #.*-cells optional for simple props
of: base: add of_parse_phandle_with_optional_args()
net: add helper eth_addr_add()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of serial and tty driver updates for 6.3-rc1.
Once again, Jiri and Ilpo have done a number of core vt and tty/serial
layer cleanups that were much needed and appreciated. Other than that,
it's just a bunch of little tty/serial driver updates:
- qcom-geni-serial driver updates
- liteuart driver updates
- hvcs driver cleanups
- n_gsm updates and additions for new features
- more 8250 device support added
- fpga/dfl update and additions
- imx serial driver updates
- fsl_lpuart updates
- other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (143 commits)
tty: n_gsm: add keep alive support
serial: imx: remove a redundant check
dt-bindings: serial: snps-dw-apb-uart: add dma & dma-names properties
soc: qcom: geni-se: Move qcom-geni-se.h to linux/soc/qcom/geni-se.h
tty: n_gsm: add TIOCMIWAIT support
tty: n_gsm: add RING/CD control support
tty: n_gsm: mark unusable ioctl structure fields accordingly
serial: imx: get rid of registers shadowing
serial: imx: refine local variables in rxint()
serial: imx: stop using USR2 in FIFO reading loop
serial: imx: remove redundant USR2 read from FIFO reading loop
serial: imx: do not break from FIFO reading loop prematurely
serial: imx: do not sysrq broken chars
serial: imx: work-around for hardware RX flood
serial: imx: factor-out common code to imx_uart_soft_reset()
serial: 8250_pci1xxxx: Add power management functions to quad-uart driver
serial: 8250_pci1xxxx: Add RS485 support to quad-uart driver
serial: 8250_pci1xxxx: Add driver for quad-uart support
serial: 8250_pci: Add serial8250_pci_setup_port definition in 8250_pcilib.c
tty: pcn_uart: fix memory leak with using debugfs_lookup()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt driver updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver changes for 6.3-rc1.
Nothing major in here, just lots of good development, including:
- Thunderbolt additions for new device support and features
- xhci driver updates and cleanups
- USB gadget media driver updates (includes media core changes that
were acked by the v4l2 maintainers)
- lots of other USB gadget driver updates for new features
- dwc3 driver updates and fixes
- minor debugfs leak fixes
- typec driver updates and additions
- dt-bindings conversions to yaml
- other small bugfixes and driver updates
All have been in linux-next for a while with no reported issues"
* tag 'usb-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (237 commits)
usb: dwc3: xilinx: Remove unused of_gpio,h
usb: typec: pd: Add higher capability sysfs for sink PDO
usb: typec: pd: Remove usb_suspend_supported sysfs from sink PDO
usb: dwc3: pci: add support for the Intel Meteor Lake-M
usb: gadget: u_ether: Don't warn in gether_setup_name_default()
usb: gadget: u_ether: Convert prints to device prints
usb: gadget: u_serial: Add null pointer check in gserial_resume
usb: gadget: uvc: fix missing mutex_unlock() if kstrtou8() fails
xhci: host: potential NULL dereference in xhci_generic_plat_probe()
dt-bindings: usb: amlogic,meson-g12a-usb-ctrl: make G12A usb3-phy0 optional
usb: host: fsl-mph-dr-of: reuse device_set_of_node_from_dev
of: device: Do not ignore error code in of_device_uevent_modalias
of: device: Ignore modalias of reused nodes
usb: gadget: configfs: Fix set but not used variable warning
usb: gadget: uvc: Use custom strings if available
usb: gadget: uvc: Allow linking function to string descs
usb: gadget: uvc: Pick up custom string descriptor IDs
usb: gadget: uvc: Allow linking XUs to string descriptors
usb: gadget: configfs: Attach arbitrary strings to cdev
usb: gadget: configfs: Support arbitrary string descriptors
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"Removed Drivers:
- HTC ASIC3 LED
New Functionality:
- Provide generic led_get() which can be used by both DT and !DT
platforms
Fix-ups:
- Convert a bunch of I2C subsystem users to the new probing API
- Explicitly provide missing include files
- Make use of led_init_default_state_get() and rid the custom
variants
- Use simplified fwnode_device_is_compatible() API
- Provide some Device Tree additions / adaptions
- Fix some trivial spelling issues
Bug Fixes:
- Prevent device refcount leak during led_put() and of_led_get()
- Clear previous data from temporary led_pwm structure before
processing next child
- Fix Clang's warning about incompatible function types when using
devm_add_action*()"
* tag 'leds-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (41 commits)
leds: Remove ide-disk trigger
dt-bindings: leds: Add disk write/read and usb-host/usb-gadget
Documentation: leds: Correct spelling
dt-bindings: leds: Document Bluetooth and WLAN triggers
leds: Remove asic3 driver
leds: simatic-ipc-leds-gpio: Make sure we have the GPIO providing driver
leds: tca6507: Convert to use fwnode_device_is_compatible()
leds: syscon: Get rid of custom led_init_default_state_get()
leds: pm8058: Get rid of custom led_init_default_state_get()
leds: pca955x: Get rid of custom led_init_default_state_get()
leds: mt6360: Get rid of custom led_init_default_state_get()
leds: mt6323: Get rid of custom led_init_default_state_get()
leds: bcm6358: Get rid of custom led_init_default_state_get()
leds: bcm6328: Get rid of custom led_init_default_state_get()
leds: an30259a: Get rid of custom led_init_default_state_get()
leds: Move led_init_default_state_get() to the global header
leds: Add missing includes and forward declarations in leds.h
leds: is31fl319x: Wrap mutex_destroy() for devm_add_action_or_rest()
leds: turris-omnia: Convert to i2c's .probe_new()
leds: tlc591xx: Convert to i2c's .probe_new()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
"New Drivers:
- Add support for Kinetic KTZ8866 Backlight
Removed Drivers:
- Toshiba Sharp SL-6000 LCD and Backlight
Fix-ups:
- Provide some profiling optimisations with respect to
pwm_get_state() and pwm_apply_state()
- Make use of the dev_err_probe() API
- Provide some Device Tree documentation additions / adaptions
- Drop fall-back legacy PWM probing support
- Convert over to new I2C probing API
- Fix incorrect documentation
- Make use of backlight_get_brightness() API
Bug Fixes:
- Fix disabling backlight on i.MX6 when inverted PWMs are used"
* tag 'backlight-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: ktz8866: Convert to i2c's .probe_new()
backlight: ktz8866: Add support for Kinetic KTZ8866 backlight
dt-bindings: leds: backlight: Add Kinetic KTZ8866 backlight
backlight: pwm_bl: Don't rely on a disabled PWM emiting inactive state
backlight: pwm_bl: Configure pwm only once per backlight toggle
backlight: Remove pxa tosa support
backlight: aat2870: Use backlight helper
backlight: ipaq_micro: Use backlight helper
backlight: arcxcnn: Use backlight helper
backlight: sky81452: Fix sky81452_bl_platform_data kernel-doc
backlight: pwm_bl: Drop support for legacy PWM probing
dt-bindings: backlight: qcom-wled: Add PMI8950 compatible
backlight: ktd253: Switch to use dev_err_probe() helper
backlight: backlight: Fix doc for backlight_device_get_by_name
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Framework:
- Change MFD support status from Supported to Maintained
New Drivers:
- Add support for the Intel Platform Management Component Interface
(PMCI)
Removed Drivers:
- HTC PASIC3 LED/DS1WM
- Toshiba T7L66XB, TC6387XB and TC6393XB TMIO
New Device Support:
- Add support for N6000 Flash to Intel M10 BMC PMCI
- Add support for Lenovo Yoga Tab 3 to Intel CHTWC PMIC
New Functionality:
- Provide Reset support to Syscon
Fix-ups:
- Explicitly provide missing include files
- Pass platform type data/info via the SPI/I2C/DT registration
strategy
- Lots of DT documentation / adaptions
- Replace scnprintf() with preferred sysfs_emit()
- Remove unused / superfluous code
- Fix some trivial whitesspace / spelling / grammatical issues
- Replace pm_power_off with new and improved
register_sys_off_handler() API
Bug Fixes:
- Reintroduce RK808-clkout registration - fixing Wi-Fi and Bluetooth
- Repair the order of AXPxxx IRQ PEK RISE/FALL definitions
- Refuse to build CS5535 on unsupported UML architectures
- Fix memory leaks in error return paths
- Prevent refcount leaks in error return paths"
* tag 'mfd-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (40 commits)
dt-bindings: mfd: qcom,tcsr: Add compatible for IPQ5332
dt-bindings: mfd: Add NXP BBNSM
mfd: ntxec: Add version number for EC in Tolino Vision
dt-bindings: mfd: syscon: Add mt8365-syscfg
mfd: Remove toshiba tmio drivers
mfd: arizona: Use pm_runtime_resume_and_get() to prevent refcnt leak
mfd: syscon: Allow reset control for syscon devices
dt-bindings: mfd/syscon: Add resets property
dt-bindings: mfd: syscon: Add amd,pensando-elba-syscon compatible
dt-bindings: mfd: qcom,tcsr: Add compatible for MSM8226
mfd: simple-mfd-i2c: Fix incoherent comment regarding DT registration
mfd: axp20x: Switch to the sys-off handler API
mfd: core: Spelling s/compement/complement/
mfd: max8925: Remove the unused function irq_to_max8925()
mfd: qcom-pm8xxx: Remove set but unused variable 'rev'
dt-bindings: mfd: syscon: Document GXP register compatible
mfd: twl4030-power: Drop empty platform remove function
mfd: twl: Fix TWL6032 phy vbus detection
mfd: pcf50633-adc: Fix potential memleak in pcf50633_adc_async_read()
MAINTAINERS: Move MFD from a Supported to Maintaied state
...
|
|
Pull drm updates from Dave Airlie:
"There are a bunch of changes all over in the usual places.
Highlights:
- habanalabs moves from misc to accel
- first accel driver for Intel VPU (Versatile Processing Unit)
inference engine
- dropped all the ancient legacy DRI1 drivers. I think it's been at
least 10 years since anyone has heard about these.
- Intel DG2 updates and prelim Meteorlake enablement
- etnaviv adds support for Versilicon NPU device (a GPU like engine
with inference accelerators)
Detailed summary:
Removals:
- remove legacy dri1 drivers: i810, mga, r128, savage, sis, tdfx, via
New driver:
- intel VPU accelerator driver
- habanalabs comes via drm tree now
drm/core:
- use drm_dbg_ helpers in several places
- Document defaults for CRTC backgrounds
- Document use of drm_minor
edid:
- improve mode parsing and refactoring
connector:
- support analog TV mode property
media:
- add some common formats
udmabuf:
- add vmap/vunmap methods
fourcc:
- add XRGB1555 and RGB565 formats
- document open source user waiver
firmware:
- fix color-format selection for system framebuffer
format-helper:
- Add conversion from XRGB8888 to various sysfb formats
- Make XRGB8888 the only driver-emulated legacy format
- Add conversion from XRGB8888 to XBGR8888 and ABGR8888
fb-helper:
- fix preferred depth and bpp values across drivers
- Avoid blank consoles from selecting an incorrect color format
probe-helper:
- Enable/disable HPD on connectors
scheduler:
- Fix lockup in drm_sched_entity_kill()
- Deprecate drm_sched_resubmit_jobs()
bridge:
- remove unused functions
- implement i2c probe_new in various drivers
- ite-it6505: Locking fixes, Cache EDID data
- ite-it66121: Support IT6610 chip
- lontium-tl9611: Fix HDMI on DragonBoard 845c
- parade-ps8640: Use atomic bridge functions
- Support i.MX93 LDB plus DT bindings
debugfs:
- add per device helpers and convert drivers
displayport:
- mst fixes
- add DP adaptive sync DPCD definitions
fbdev:
- always pick 32bpp as default
- remove some unused code
simpledrm:
- support system memory framebuffers
panel:
- add orientation quirks for Lenovo Yoga Tab 3 X90F and DynaBook K50
- Use ktime_get_boottime() to measure power-down delay
- Fix auto-suspend delay
- Visionox VTDR6130 AMOLED DSI
- Support Himax HX8394
- Convert many drivers to common generic DSI write-sequence helper
- AUO A030JTN01
ttm:
- drop bo wait wrapper
- fix MIPS build
habanalabs:
- moved driver to accel subsystem
- gaudi2 decoder error improvement
- more trace events
- Gaudi2 abrupt reset by firmware support
- add uAPI to flush memory transactions
- add uAPI to pass through userspace reqs to fw
- remove dma-buf export by handle
amdgpu:
- add new INFO queries for peak and min sclk/mclk for profile modes
- Add PCIe info to the INFO IOCTL
- secure display support for multiple displays
- DML optimizations
- DCN 3.2 updates
- PSR updates
- DP 2.1 updates
- SR-IOV RAS updates
- VCN RAS support
- SMU 13.x updates
- Switch 1 element arrays to flexible arrays
- Add RAS support for DF 4.3
- Stack size improvements
- S0ix rework
- Allow 0 as a vram limit on APUs
- Handle profiling modes for SMU13.x
- Fix possible segfault in failure case
- Rework FW requests to happen in early_init for all IPs so that we
don't lose the sbios console if FW is missing
- Fix power reporting on certain firmwares for CZN/RN
- Allow S0ix without BIOS support
- Enable freesync over PCon
- Re-enable the AGP aperture on GMC 11.x
amdkfd:
- Error handling fixes
- PASID fixes
- Fix for cleared VRAM BOs
- Fix cleanup if GPUVM creation fails
- Memory accounting fix
- Use resource_size rather than open codeing it
- GC11 mGPU fix
radeon:
- Switch 1 element arrays to flexible arrays
- Fix memory leak on shutdown
- move to new logging
i915:
- Meteorlake display/OA/GSC fw/workarounds enabling
- DP MST DSC support
- Gamma/degamma readout support for the state checker
- Enable SDP split support for DP 2.0
- Add probe blocking support to i915.force_probe parameter
- Enable Xe HP 4tile support
- Avoid display direct calls to uncore
- Fix HuC delayed load memory leaks
- Add DG2 workarounds Wa_18018764978 and Wa_18019271663
- Improve suspend / resume times with VT-d scanout workaround active
- Fix DG2 visual corruption on small BAR systems by not forgetting to
copy CCS aux state
- Fix TLB invalidation for Gen12.50 video and compute engines
- Enable HF-EEODB by switching HDMI, DP and LVDS to use struct
drm_edid
- Start using unversioned DMC firmware paths for new platforms
- ELD refactor: Stop using hardware buffer, precompute ELD
- lots of display code refactoring
nouveau:
- drop legacy ioctl support
- replace 0-sized array
msm:
- dpu/dsi/mdss: Support for SM8350, SM8450 SM8550 and SC8280XP platform
- Added bindings for SM8150
- dpu: Partial support for DSC on SM8150 and SM8250
- dpu: Fixed color transformation matrix being lost on suspend/resume
- dp: Support SDM845 and SC8280XP platforms
- dp: Support for limiting DP link rate via DT property
- dsi: Validate display modes according to the DSI OPP table
- dsi: DSI PHY support for the SM6375 platform
- Add MSM_SUBMIT_BO_NO_IMPLICI
- a2xx: Support to load legacy firmware
- a6xx: GPU devcore dump updates for a650/a660
- GPU devfreq tuning and fixes
- Turn 8960 HDMI PHY into clock provider,
- Make 8960 HDMI PHY use PXO clock from DT
etnaviv:
- experimental versilicon NPU support
- report GPU load via fdinfo format
- MMU fault message improvements
tegra:
- rework syncpoint interrupt
mediatek:
- DSI timing fix
- fix config deps
ast:
- various fixes
exynos:
- restore bridge chain order fixes
gud:
- convert to shadow plane buffers
- perform flushing synchronously during atomic update
- Use new debugfs helpers
arm/hdlcd:
- Use new debugfs helper
ili9486:
- Support 16-bit pixel data
imx:
- Split off IPUv3 driver
mipi-dbi:
- convert to DRM shadow-plane helpers
- rsp driver changes
- Support separate I/O-voltage supply
mxsfb:
- Depend on ARCH_MXS or ARCH_MXC
sun4i:
- convert to new TV mode property
vc4:
- convert to new TV mode property
- kunit tests
- Support RGB565 and RGB666 formats
- convert dsi driver to bridge
- Various HVS an CRTC fixes
v3d:
- Do not opencode drm_gem_object_lookup()
virtio:
- improve tracing
vkms:
- support small cursors in IGT tests
- Fix SEGFAULT from incorrect GEM-buffer mapping
rcar-du:
- fixes and improvements"
* tag 'drm-next-2023-02-23' of git://anongit.freedesktop.org/drm/drm: (1455 commits)
msm/fbdev: fix unused variable warning with clang.
drm/fb-helper: Remove drm_fb_helper_unprepare() from drm_fb_helper_fini()
dma-buf: make kobj_type structure constant
drm/shmem-helper: Fix locking for drm_gem_shmem_get_pages_sgt()
drm/amd/display: disable SubVP + DRR to prevent underflow
drm/amd/display: Fail atomic_check early on normalize_zpos error
drm/amd/pm: avoid unaligned access warnings
drm/amd/display: avoid unaligned access warnings
drm/amd/display: Remove duplicate/repeating expressions
drm/amd/display: Remove duplicate/repeating expression
drm/amd/display: Make variables declaration inside ifdef guard
drm/amd/display: Fix excess arguments on kernel-doc
drm/amd/display: Add previously missing includes
drm/amd/amdgpu: Add function prototypes to headers
drm/amd/display: Add function prototypes to headers
drm/amd/display: Turn global functions into static
drm/amd/display: remove unused _calculate_degamma_curve function
drm/amd/display: remove unused func declaration from resource headers
drm/amd/display: unset initial value for tf since it's never used
drm/amd/display: camel case cleanup in color_gamma file
...
|
|
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, lpfc, qla2xxx, libsas).
The major core change is a rework to remove the two helpers around
scsi_execute_cmd and use it as the only submission interface along
with other minor fixes and updates"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (142 commits)
scsi: ufs: core: Fix an error handling path in ufshcd_read_desc_param()
scsi: ufs: core: Fix device management cmd timeout flow
scsi: aic94xx: Add missing check for dma_map_single()
scsi: smartpqi: Replace one-element array with flexible-array member
scsi: mpt3sas: Fix a memory leak
scsi: qla2xxx: Remove the unused variable wwn
scsi: ufs: core: Fix kernel-doc syntax
scsi: ufs: core: Add hibernation callbacks
scsi: snic: Fix memory leak with using debugfs_lookup()
scsi: ufs: core: Limit DMA alignment check
scsi: Documentation: Correct spelling
scsi: Documentation: Correct spelling
scsi: target: Documentation: Correct spelling
scsi: aacraid: Allocate cmd_priv with scsicmd
scsi: ufs: qcom: dt-bindings: Add SM8550 compatible string
scsi: ufs: ufs-qcom: Clear qunipro_g4_sel for HW version major 5
scsi: ufs: qcom: fix platform_msi_domain_free_irqs() reference
scsi: ufs: core: Enable DMA clustering
scsi: ufs: exynos: Fix the maximum segment size
scsi: ufs: exynos: Fix DMA alignment for PAGE_SIZE != 4096
...
|
|
- Clean up uniphier-ep reg, clocks, resets, and their names (Kunihiko
Hayashi)
* pci/controller/uniphier:
dt-bindings: PCI: uniphier-ep: Clean up reg, clocks, resets, and their names
|
|
- Add DT compatible for qcom MSM8998 (Krzysztof Kozlowski)
- Unify qcom MSM8996 and MSM8998 clock orderings (Krzysztof Kozlowski)
- Correct qcom,perst-regs (Krzysztof Kozlowski)
- Add qcom SM8350 DT binding and driver support (Dmitry Baryshkov)
- Add qcom_pcie_host_deinit() so the PHY is powered off and regulators and
clocks are disabled on late host-init errors (Johan Hovold)
- Add IPQ8074 Gen3 port DT binding and driver support (the Gen2 port was
already supported) (Robert Marko)
* pci/controller/qcom:
PCI: qcom: Add IPQ8074 Gen3 port support
dt-bindings: PCI: qcom: Add IPQ8074 Gen3 port
dt-bindings: PCI: qcom: Sort compatibles alphabetically
PCI: qcom: Fix host-init error handling
PCI: qcom: Add SM8350 support
dt-bindings: PCI: qcom: Add SM8350
dt-bindings: PCI: qcom-ep: Correct qcom,perst-regs
dt-bindings: PCI: qcom: Unify MSM8996 and MSM8998 clock order
dt-bindings: PCI: qcom: Add MSM8998 specific compatible
dt-bindings: PCI: qcom: Add oneOf to compatible match
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"New drivers:
- Infineon TDA38640 Voltage Regulator
- NXP MC34VR500 PMIC
- GXP fan controller
- MPQ7932 Power Management IC
New chip or board support added to existing drivers:
- it87: IT87952E; also other cleanup/improvements
- intel-m10-bmc-hwmon: N6000
- pmbus/max16601: MAX16600
- aquacomputer_d5next: Aquacomputer Aquastream Ultimate, Aquacomputer
Poweradjust 3, Aquacomputer Aquaero
- nct6775: Support for B650/B660/X670 ASUS boards
- oxp-sensors: AYANEO AIR and AIR Pro
Other notable changes:
- Various kernel documentation fixes
- Various devicetree bindings fixes
- Explicitly deprecated [devm_]hwmon_device_register_with_groups
- ftsteutates: Support for fanX_fault and other cleanup
- ltc2945: Support for setting shunt resistor and other cleanup/fixes
- coretemp: Avoid RDMSR interrupts to isolated CPUs, and simplify
platform device handling
... and various other minor cleanups and fixes"
* tag 'hwmon-for-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (66 commits)
hwmon: Deprecate [devm_]hwmon_device_register_with_groups
hwmon: (mlxreg-fan) Return zero speed for broken fan
hwmon: (gxp-fan-ctrl) use devm_platform_get_and_ioremap_resource()
hwmon: (aquacomputer_d5next) Add support for Aquacomputer Aquastream Ultimate
hwmon: (aquacomputer_d5next) Add support for Aquacomputer Poweradjust 3
hwmon: (iio_hwmon) use dev_err_probe
hwmon: intel-m10-bmc-hwmon: Add N6000 sensors
Docs/hwmon/index: Add missing SPDX License Identifier
hwmon: (it87) Updated documentation for recent updates to it87
hwmon: (it87) Add new chipset IT87952E
hwmon: (it87) Allow multiple chip IDs for force_id
hwmon: (it87) Add chip_id in some info message
hwmon: (it87) List full chip model name
hwmon: (it87) Disable configuration exit for certain chips
hwmon: (it87) Allow disabling exiting of configuration mode
Documentation: hwmon: correct spelling
hwmon: (pmbus/max16601) Add support for MAX16600
hwmon: (ltc2945) Allow setting shunt resistor
hwmon: (ltc2945) Handle error case in ltc2945_value_store
hwmon: (ltc2945) Add devicetree match table
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID updates from Benjamin Tissoires:
- HID-BPF infrastructure: this allows to start using HID-BPF. Note that
the mechanism to ship HID-BPF program through the kernel tree is
still not implemented yet (but is planned).
This should be a no-op for 99% of users. Also we are gaining
kselftests for the HID tree (Benjamin Tissoires)
- Some UAF fixes in workers when using uhid (Pietro Borrello & Benjamin
Tissoires)
- Constify hid_ll_driver (Thomas Weißschuh)
- Allow more custom IIO sensors through HID (Philipp Jungkamp)
- Logitech HID++ fixes for scroll wheel, protocol and debug (Bastien
Nocera)
- Some new device support: Steam Deck (Vicki Pfau), UClogic (José
Expósito), Logitech G923 Xbox Edition steering wheel (Walt Holman),
EVision keyboards (Philippe Valembois)
- other assorted code cleanups and fixes
* tag 'for-linus-2023022201' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (99 commits)
HID: mcp-2221: prevent UAF in delayed work
hid: bigben_probe(): validate report count
HID: asus: use spinlock to safely schedule workers
HID: asus: use spinlock to protect concurrent accesses
HID: bigben: use spinlock to safely schedule workers
HID: bigben_worker() remove unneeded check on report_field
HID: bigben: use spinlock to protect concurrent accesses
HID: logitech-hidpp: Add myself to authors
HID: logitech-hidpp: Retry commands when device is busy
HID: logitech-hidpp: Add more debug statements
HID: Add support for Logitech G923 Xbox Edition steering wheel
HID: logitech-hidpp: Add Signature M650
HID: logitech-hidpp: Remove HIDPP_QUIRK_NO_HIDINPUT quirk
HID: logitech-hidpp: Don't restart communication if not necessary
HID: logitech-hidpp: Add constants for HID++ 2.0 error codes
Revert "HID: logitech-hidpp: add a module parameter to keep firmware gestures"
HID: logitech-hidpp: Hard-code HID++ 1.0 fast scroll support
HID: i2c-hid: goodix: Add mainboard-vddio-supply
dt-bindings: HID: i2c-hid: goodix: Add mainboard-vddio-supply
HID: i2c-hid: goodix: Stop tying the reset line to the regulator
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Nothing special, notably a lot of new Qualcomm hardware is supported,
a RISC-V reference SoC and then some cleanups both in code and device
tree bindings.
Core changes:
- Add PINCTRL_PINFUNCTION() macro and use it in several drivers
New drivers:
- New driver for the StarFive JH7110 SoC "sys" and "aon" (always-on)
pin controllers. (RISC-V.)
- New subdriver for the Qualcomm QDU1000/QRU1000 SoC pin controller
- New subdrivers for the Qualcomm SM8550 SoC and LPASS pin
controllers
- New subdriver for the Qualcomm SA8775P SoC pin controller
- New subdriver for the Qualcomm IPQ5332 SoC pin controller
- New (trivial) support for Qualcomm PM8550 and PMR735D PMIC pin
control
- New subdriver for the Mediatek MT7981 SoC pin controller
Improvements:
- Several cleanups and refactorings to the Intel drivers
- Add 4KOhm bias support to the Intel driver
- Use the NOIRQ_SYSTEM_SLEEP_PM_OPS for the AT91 driver
- Support general purpose clocks in the Qualcomm MSM8226 SoC
- Several conversions to use the new I2C .probe_new() call
- Massive clean-up of the Qualcomm Device Tree YAML schemas
- Add VIN[45] pins, groups and functions to the Renesas r8a77950 SoC
driver"
* tag 'pinctrl-v6.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (118 commits)
pinctrl: qcom: Add support for i2c specific pull feature
pinctrl: starfive: Add StarFive JH7110 aon controller driver
pinctrl: starfive: Add StarFive JH7110 sys controller driver
dt-bindings: pinctrl: Add StarFive JH7110 aon pinctrl
dt-bindings: pinctrl: Add StarFive JH7110 sys pinctrl
pinctrl: add mt7981 pinctrl driver
dt-bindings: pinctrl: add bindings for MT7981 SoC
dt-bindings: pinctrl: rockchip,pinctrl: mark gpio sub nodes of pinctrl as deprecated
pinctrl: qcom: Introduce IPQ5332 TLMM driver
dt-bindings: pinctrl: qcom: add IPQ5332 pinctrl
dt-bindings: pinctrl: qcom: lpass-lpi: correct GPIO name pattern
pinctrl: qcom: pinctrl-sm8550-lpass-lpi: add SM8550 LPASS
dt-bindings: pinctrl: qcom,sm8550-lpass-lpi-pinctrl: add SM8550 LPASS
pinctrl: at91: use devm_kasprintf() to avoid potential leaks
dt-bindings: pinctrl: qcom: correct gpio-ranges in examples
dt-bindings: pinctrl: qcom,msm8994: correct number of GPIOs
dt-bindings: pinctrl: qcom,sdx55: correct GPIO name pattern
dt-bindings: pinctrl: qcom,msm8953: correct GPIO name pattern
dt-bindings: pinctrl: qcom,sm6375: correct GPIO name pattern and example
dt-bindings: pinctrl: qcom,msm8909: correct GPIO name pattern and example
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"A rather small update, there are no new drivers, just improvements and
refactoring in existing ones.
Thanks to migrating of several drivers to using generalized APIs and
dropping of OF interfaces in favor of using software nodes we're
actually removing more code than we're adding.
Core GPIOLIB:
- drop several OF interfaces after moving a significant part of the
code to using software nodes
- remove more interfaces referring to the global GPIO numberspace
that we're getting rid of
- improvements in the gpio-regmap library
- add helper for GPIO device reference counting
- remove unused APIs
- minor tweaks like sorting headers alphabetically
Extended support in existing drivers:
- add support for Tegra 234 PMC to gpio-tegra186
Driver improvements:
- migrate the 104-dio/idi family of drivers to using the regmap-irq
API
- migrate gpio-i8255 and gpio-mm to the GPIO regmap API
- clean-ups in gpio-pca953x
- remove duplicate assignments of of_gpio_n_cells in gpio-davinci,
gpio-ge, gpio-xilinx, gpio-zevio and gpio-wcd934x
- improvements to gpio-pcf857x: implement get/set_multiple callbacks,
use generic device properties instead of OF + minor tweaks
- fix OF-related header includes and Kconfig dependencies in
gpio-zevio
- dynamically allocate the GPIO base in gpio-omap
- use a dedicated printf specifier for printing fwnode info in
gpio-sim
- use dev_name() for the GPIO chip label in gpio-vf610
- other minor tweaks and fixes
Documentation:
- remove mentions of legacy API from comments in various places
- convert the DT binding documents to YAML schema for Fujitsu
MB86S7x, Unisoc GPIO and Unisoc EIC
- document the Unisoc UMS512 controller in DT bindings"
* tag 'gpio-updates-for-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (54 commits)
gpio: sim: Use %pfwP specifier instead of calling fwnode API directly
gpio: tegra186: remove unneeded loop in tegra186_gpio_init_route_mapping()
gpiolib: of: Move enum of_gpio_flags to its only user
gpio: mvebu: Use IS_REACHABLE instead of IS_ENABLED for CONFIG_PWM
gpio: zevio: Add missing header
gpio: Get rid of gpio_to_chip()
gpio: pcf857x: Drop unneeded explicit casting
gpio: pcf857x: Make use of device properties
gpio: pcf857x: Get rid of legacy platform data
gpio: rockchip: Do not mention legacy API in the code
gpio: wcd934x: Remove duplicate assignment of of_gpio_n_cells
gpio: zevio: Use proper headers and drop OF_GPIO dependency
gpio: zevio: Remove duplicate assignment of of_gpio_n_cells
gpio: xilinx: Remove duplicate assignment of of_gpio_n_cells
dt-bindings: gpio: Add compatible string for Unisoc UMS512
dt-bindings: gpio: Convert Unisoc EIC controller binding to yaml
dt-bindings: gpio: Convert Unisoc GPIO controller binding to yaml
gpio: ge: Remove duplicate assignment of of_gpio_n_cells
gpio: davinci: Remove duplicate assignment of of_gpio_n_cells
gpio: omap: use dynamic allocation of base
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"This has been a fairly quiet release for SPI, though it is likely that
the next release will have some big changes as there's some
preparatory work for multiple chip select support gone in - the rest
of the code is on the list but will need to be rebased onto -rc1.
Otherwise there's a couple of new tunables for chip select timings,
some new devices and smaller device specific updates and fixes.
- Support for configuring the hold and minimum inactive times for
chip selects.
- Beginnings of support for supporting devices which have multiple
chip selects on a single device.
- Support for newer Broadcom HSSPI and Intel controllers, Silicon
Labs EM3581 and SI3210"
* tag 'spi-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (67 commits)
spi: dt-bindings: qcom,spi-qcom-qspi: document OPP and power-domains
spi: spidev: drop the incorrect notice from Kconfig
spi: bcm63xx-hsspi: fix error code in probe
spi: bcmbca-hsspi: Fix error code in probe() function
spi: synquacer: Fix timeout handling in synquacer_spi_transfer_one()
spi: intel: Check number of chip selects after reading the descriptor
spi: xilinx: add force_irq for QSPI mode
spi: spi-st-ssc: convert to DT schema
spi: Reorder fields in 'struct spi_transfer'
spi: cadence-quadspi: use STIG mode for small reads
spi: cadence-quadspi: setup ADDR Bits in cmd reads
spi: cadence-quadspi: Add flag for direct mode writes
spi: cadence-quadspi: Reset CMD_CTRL Reg on cmd r/w completion
MAINTAINERS: Remove file reference for Broadcom Broadband SoC HS SPI driver entry
spi: bcm63xx-hsspi: bcmbca-hsspi: fix _be16 type usage
MAINTAINERS: Add entry for Broadcom Broadband SoC HS SPI drivers
spi: bcmbca-hsspi: Add driver for newer HSSPI controller
spi: bcm63xx-hsspi: Disable spi mem dual io read op support
spi: spi-mem: Allow controller supporting mem_ops without exec_op
spi: bcm63xx-hsspi: Add prepend mode support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"This has been a very quiet release for the regulator API: there's one
new driver for the Maxim MAX20411, some DT schema conversions and some
small tweaks and improvements but really nothing major at all"
* tag 'regulator-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (22 commits)
regulator: max597x: Align for simple_mfd_i2c driver
regulator: max20411: Fix off-by-one for n_voltages setting
regulator: max597x: Remove unused variable
regulator: tps65219: use generic set_bypass()
regulator: s5m8767: Bounds check id indexing into arrays
regulator: max77802: Bounds check regulator id against opmode
regulator: max20411: Convert to i2c's .probe_new()
regulator: scmi: Allow for zero voltage domains
regulator: max20411: Directly include bitfield.h
regulator: Introduce Maxim MAX20411 Step-Down converter
regulator: dt-bindings: Describe Maxim MAX20411
regulator: dt-bindings: qcom-labibb: Allow regulator-common properties
regulator: dt-bindings: fixed-regulator: allow gpios property
regulator: tps65219: use IS_ERR() to detect an error pointer
regulator: mcp16502: add enum MCP16502_REG_HPM description
regulator: fixed-helper: use the correct function name in comment
regulator: act8945a: fix non-kernel-doc comments
dt-bindings: regulators: convert non-smd RPM Regulators bindings to dt-schema
regulator: dt-bindings: Convert Fairchild FAN53555 to DT schema
regulator: dt-bindings: qcom,usb-vbus-regulator: change node name
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"The majority of works in this cycle are about ASoC spread over trees.
Most of them are for new devices and cleanups / refactoring works, and
not much significant changes are seen in the core side.
Below are some highlights:
ASoC:
- Continued refactoring to move into common helper functions
- Lots of DT schema conversons and stylistic nits
- Continued work on building out the new SOF IPC4 scheme
- Continued work for Intel AVS
- New drivers for Awinc AT88395, Infineon PEB2466, Iron Device
SMA1303, Mediatek MT8188, Realtek RT712, Renesas IDT821034,
Samsung/Tesla FSD SoC I2S, and TI TAS5720A-Q1
ALSA:
- A few cleanups to make the remove callbacks to void returns
- FireWire refactoring and enhancements
- PCM kselftest enhancements"
* tag 'sound-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (398 commits)
ALSA: hda/hdmi: Register with vga_switcheroo on Dual GPU Macbooks
ASoC: soc-ac97: Return correct error codes
ASoC: soc-dapm.h: fixup warning struct snd_pcm_substream not declared
ASoC: cs35l45: Remove separate namespace for tables
ASoC: cs35l45: Remove separate tables module
ASoC: soc-ac97: Convert to agnostic GPIO API
ASoC: dt-bindings: renesas,rsnd.yaml: drop "dmas/dma-names" from "rcar_sound,ssi"
ALSA: hda: cs35l41: Enable Amp High Pass Filter
ALSA: hda: cs35l41: Ensure firmware/tuning pairs are always loaded
ALSA: hda: cs35l41: Correct error condition handling
ASoC: codecs: wcd934x: Use min macro for comparison and assignment
ASoC: Intel: Skylake: Fix struct definition
ASoC: tlv320adcx140: extend list of supported samplerates
ASoC: imx-pcm-rpmsg: Remove unused variable
SoC: rt5682s: Disable jack detection interrupt during suspend
ASoC: SOF: Intel: hda-dsp: Set streaming flag for d0i3
ASoC: SOF: Intel: Enable d0i3 work for ipc4
ASoC: SOF: ipc4: Wake up dsp core before sending ipc msg
ASoC: SOF: Intel: hda-dsp: use set_pm_gate according to ipc version
ASoC: SOF: Introduce a new set_pm_gate() IPC PM op
...
|
|
Document the qcom,tcsr-ipq5332 compatible.
Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230130170155.27266-2-quic_kathirav@quicinc.com
|
|
Add binding for NXP BBNSM(Battery-Backed Non-Secure Module).
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230129070823.1945489-2-ping.bai@nxp.com
|
|
Document Mediatek mt8365-syscfg
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230125143503.1015424-4-bero@baylibre.com
|
|
Add Kinetic KTZ8866 backlight binding documentation.
Signed-off-by: Jianhua Lu <lujianhua000@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230120155018.15376-1-lujianhua000@gmail.com
|
|
Document the compatible for the wled block found in PMI8950.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221101161801.1058969-1-luca@z3ntu.xyz
|
|
- dev_dbg cleanup (Thomas Weißschuh)
- cleanup i2c-hid-acpi (Andy Shevchenko)
- goodix: revert/fixes for an actual production device compared to the
manufacturer sample (Douglas Anderson)
|
|
Simple syscon devices may require deassertion of a reset signal in order
to access their register set. This change adds the `resets` property from
reset.yaml#/properties/resets (referenced through core.yaml), specifying
a maxItems of 1 for a single (optional) reset descriptor.
This will allow a future change to the syscon driver to implement reset
control.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230105005010.124948-2-jk@codeconstruct.com.au
|
|
Add the AMD Pensando Elba SoC system registers compatible
Signed-off-by: Brad Larson <blarson@amd.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230119035136.21603-6-blarson@amd.com
|
|
Document the qcom,msm8226-tcsr compatible.
Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230112202612.791455-5-matti.lehtimaki@gmail.com
|
|
Document hpe,gxp-sysreg compatible for GXP registers.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221216183532.78933-4-nick.hawkins@hpe.com
|
|
Add a compatible string to support the UART implementation of the cros
ec interface. The driver does not support the reg and interrupt
properties, so exempt them from being required for UART compatible nodes.
Signed-off-by: Bhanu Prakash Maiya <bhanumaiya@chromium.org>
Co-developed-by: Mark Hasemeyer <markhas@chromium.org>
Signed-off-by: Mark Hasemeyer <markhas@chromium.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221207104005.v10.2.I9e018ecb8bdf341648cb64417085978ff0d22a46@changeid
|
|
Document compatible for the pm8550, pm8550b, pm8550ve, pm8550vs, pmk8550.
pm8010 & pmr735d SPMI PMICs
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221114-narmstrong-sm8550-upstream-spmi-v2-1-b839bf2d558a@linaro.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- Add dedicated kmem_cache for typical/small skb->head, avoid having
to access struct page at kfree time, and improve memory use.
- Introduce sysctl to set default RPS configuration for new netdevs.
- Define Netlink protocol specification format which can be used to
describe messages used by each family and auto-generate parsers.
Add tools for generating kernel data structures and uAPI headers.
- Expose all net/core sysctls inside netns.
- Remove 4s sleep in netpoll if carrier is instantly detected on
boot.
- Add configurable limit of MDB entries per port, and port-vlan.
- Continue populating drop reasons throughout the stack.
- Retire a handful of legacy Qdiscs and classifiers.
Protocols:
- Support IPv4 big TCP (TSO frames larger than 64kB).
- Add IP_LOCAL_PORT_RANGE socket option, to control local port range
on socket by socket basis.
- Track and report in procfs number of MPTCP sockets used.
- Support mixing IPv4 and IPv6 flows in the in-kernel MPTCP path
manager.
- IPv6: don't check net.ipv6.route.max_size and rely on garbage
collection to free memory (similarly to IPv4).
- Support Penultimate Segment Pop (PSP) flavor in SRv6 (RFC8986).
- ICMP: add per-rate limit counters.
- Add support for user scanning requests in ieee802154.
- Remove static WEP support.
- Support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate
reporting.
- WiFi 7 EHT channel puncturing support (client & AP).
BPF:
- Add a rbtree data structure following the "next-gen data structure"
precedent set by recently added linked list, that is, by using
kfunc + kptr instead of adding a new BPF map type.
- Expose XDP hints via kfuncs with initial support for RX hash and
timestamp metadata.
- Add BPF_F_NO_TUNNEL_KEY extension to bpf_skb_set_tunnel_key to
better support decap on GRE tunnel devices not operating in collect
metadata.
- Improve x86 JIT's codegen for PROBE_MEM runtime error checks.
- Remove the need for trace_printk_lock for bpf_trace_printk and
bpf_trace_vprintk helpers.
- Extend libbpf's bpf_tracing.h support for tracing arguments of
kprobes/uprobes and syscall as a special case.
- Significantly reduce the search time for module symbols by
livepatch and BPF.
- Enable cpumasks to be used as kptrs, which is useful for tracing
programs tracking which tasks end up running on which CPUs in
different time intervals.
- Add support for BPF trampoline on s390x and riscv64.
- Add capability to export the XDP features supported by the NIC.
- Add __bpf_kfunc tag for marking kernel functions as kfuncs.
- Add cgroup.memory=nobpf kernel parameter option to disable BPF
memory accounting for container environments.
Netfilter:
- Remove the CLUSTERIP target. It has been marked as obsolete for
years, and we still have WARN splats wrt races of the out-of-band
/proc interface installed by this target.
- Add 'destroy' commands to nf_tables. They are identical to the
existing 'delete' commands, but do not return an error if the
referenced object (set, chain, rule...) did not exist.
Driver API:
- Improve cpumask_local_spread() locality to help NICs set the right
IRQ affinity on AMD platforms.
- Separate C22 and C45 MDIO bus transactions more clearly.
- Introduce new DCB table to control DSCP rewrite on egress.
- Support configuration of Physical Layer Collision Avoidance (PLCA)
Reconciliation Sublayer (RS) (802.3cg-2019). Modern version of
shared medium Ethernet.
- Support for MAC Merge layer (IEEE 802.3-2018 clause 99). Allowing
preemption of low priority frames by high priority frames.
- Add support for controlling MACSec offload using netlink SET.
- Rework devlink instance refcounts to allow registration and
de-registration under the instance lock. Split the code into
multiple files, drop some of the unnecessarily granular locks and
factor out common parts of netlink operation handling.
- Add TX frame aggregation parameters (for USB drivers).
- Add a new attr TCA_EXT_WARN_MSG to report TC (offload) warning
messages with notifications for debug.
- Allow offloading of UDP NEW connections via act_ct.
- Add support for per action HW stats in TC.
- Support hardware miss to TC action (continue processing in SW from
a specific point in the action chain).
- Warn if old Wireless Extension user space interface is used with
modern cfg80211/mac80211 drivers. Do not support Wireless
Extensions for Wi-Fi 7 devices at all. Everyone should switch to
using nl80211 interface instead.
- Improve the CAN bit timing configuration. Use extack to return
error messages directly to user space, update the SJW handling,
including the definition of a new default value that will benefit
CAN-FD controllers, by increasing their oscillator tolerance.
New hardware / drivers:
- Ethernet:
- nVidia BlueField-3 support (control traffic driver)
- Ethernet support for imx93 SoCs
- Motorcomm yt8531 gigabit Ethernet PHY
- onsemi NCN26000 10BASE-T1S PHY (with support for PLCA)
- Microchip LAN8841 PHY (incl. cable diagnostics and PTP)
- Amlogic gxl MDIO mux
- WiFi:
- RealTek RTL8188EU (rtl8xxxu)
- Qualcomm Wi-Fi 7 devices (ath12k)
- CAN:
- Renesas R-Car V4H
Drivers:
- Bluetooth:
- Set Per Platform Antenna Gain (PPAG) for Intel controllers.
- Ethernet NICs:
- Intel (1G, igc):
- support TSN / Qbv / packet scheduling features of i226 model
- Intel (100G, ice):
- use GNSS subsystem instead of TTY
- multi-buffer XDP support
- extend support for GPIO pins to E823 devices
- nVidia/Mellanox:
- update the shared buffer configuration on PFC commands
- implement PTP adjphase function for HW offset control
- TC support for Geneve and GRE with VF tunnel offload
- more efficient crypto key management method
- multi-port eswitch support
- Netronome/Corigine:
- add DCB IEEE support
- support IPsec offloading for NFP3800
- Freescale/NXP (enetc):
- support XDP_REDIRECT for XDP non-linear buffers
- improve reconfig, avoid link flap and waiting for idle
- support MAC Merge layer
- Other NICs:
- sfc/ef100: add basic devlink support for ef100
- ionic: rx_push mode operation (writing descriptors via MMIO)
- bnxt: use the auxiliary bus abstraction for RDMA
- r8169: disable ASPM and reset bus in case of tx timeout
- cpsw: support QSGMII mode for J721e CPSW9G
- cpts: support pulse-per-second output
- ngbe: add an mdio bus driver
- usbnet: optimize usbnet_bh() by avoiding unnecessary queuing
- r8152: handle devices with FW with NCM support
- amd-xgbe: support 10Mbps, 2.5GbE speeds and rx-adaptation
- virtio-net: support multi buffer XDP
- virtio/vsock: replace virtio_vsock_pkt with sk_buff
- tsnep: XDP support
- Ethernet high-speed switches:
- nVidia/Mellanox (mlxsw):
- add support for latency TLV (in FW control messages)
- Microchip (sparx5):
- separate explicit and implicit traffic forwarding rules, make
the implicit rules always active
- add support for egress DSCP rewrite
- IS0 VCAP support (Ingress Classification)
- IS2 VCAP filters (protos, L3 addrs, L4 ports, flags, ToS
etc.)
- ES2 VCAP support (Egress Access Control)
- support for Per-Stream Filtering and Policing (802.1Q,
8.6.5.1)
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- add MAB (port auth) offload support
- enable PTP receive for mv88e6390
- NXP (ocelot):
- support MAC Merge layer
- support for the the vsc7512 internal copper phys
- Microchip:
- lan9303: convert to PHYLINK
- lan966x: support TC flower filter statistics
- lan937x: PTP support for KSZ9563/KSZ8563 and LAN937x
- lan937x: support Credit Based Shaper configuration
- ksz9477: support Energy Efficient Ethernet
- other:
- qca8k: convert to regmap read/write API, use bulk operations
- rswitch: Improve TX timestamp accuracy
- Intel WiFi (iwlwifi):
- EHT (Wi-Fi 7) rate reporting
- STEP equalizer support: transfer some STEP (connection to radio
on platforms with integrated wifi) related parameters from the
BIOS to the firmware.
- Qualcomm 802.11ax WiFi (ath11k):
- IPQ5018 support
- Fine Timing Measurement (FTM) responder role support
- channel 177 support
- MediaTek WiFi (mt76):
- per-PHY LED support
- mt7996: EHT (Wi-Fi 7) support
- Wireless Ethernet Dispatch (WED) reset support
- switch to using page pool allocator
- RealTek WiFi (rtw89):
- support new version of Bluetooth co-existance
- Mobile:
- rmnet: support TX aggregation"
* tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1872 commits)
page_pool: add a comment explaining the fragment counter usage
net: ethtool: fix __ethtool_dev_mm_supported() implementation
ethtool: pse-pd: Fix double word in comments
xsk: add linux/vmalloc.h to xsk.c
sefltests: netdevsim: wait for devlink instance after netns removal
selftest: fib_tests: Always cleanup before exit
net/mlx5e: Align IPsec ASO result memory to be as required by hardware
net/mlx5e: TC, Set CT miss to the specific ct action instance
net/mlx5e: Rename CHAIN_TO_REG to MAPPED_OBJ_TO_REG
net/mlx5: Refactor tc miss handling to a single function
net/mlx5: Kconfig: Make tc offload depend on tc skb extension
net/sched: flower: Support hardware miss to tc action
net/sched: flower: Move filter handle initialization earlier
net/sched: cls_api: Support hardware miss to tc action
net/sched: Rename user cookie and act cookie
sfc: fix builds without CONFIG_RTC_LIB
sfc: clean up some inconsistent indentings
net/mlx4_en: Introduce flexible array to silence overflow warning
net: lan966x: Fix possible deadlock inside PTP
net/ulp: Remove redundant ->clone() test in inet_clone_ulp().
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto update from Herbert Xu:
"API:
- Use kmap_local instead of kmap_atomic
- Change request callback to take void pointer
- Print FIPS status in /proc/crypto (when enabled)
Algorithms:
- Add rfc4106/gcm support on arm64
- Add ARIA AVX2/512 support on x86
Drivers:
- Add TRNG driver for StarFive SoC
- Delete ux500/hash driver (subsumed by stm32/hash)
- Add zlib support in qat
- Add RSA support in aspeed"
* tag 'v6.3-p1' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (156 commits)
crypto: x86/aria-avx - Do not use avx2 instructions
crypto: aspeed - Fix modular aspeed-acry
crypto: hisilicon/qm - fix coding style issues
crypto: hisilicon/qm - update comments to match function
crypto: hisilicon/qm - change function names
crypto: hisilicon/qm - use min() instead of min_t()
crypto: hisilicon/qm - remove some unused defines
crypto: proc - Print fips status
crypto: crypto4xx - Call dma_unmap_page when done
crypto: octeontx2 - Fix objects shared between several modules
crypto: nx - Fix sparse warnings
crypto: ecc - Silence sparse warning
tls: Pass rec instead of aead_req into tls_encrypt_done
crypto: api - Remove completion function scaffolding
tls: Remove completion function scaffolding
tipc: Remove completion function scaffolding
net: ipv6: Remove completion function scaffolding
net: ipv4: Remove completion function scaffolding
net: macsec: Remove completion function scaffolding
dm: Remove completion function scaffolding
...
|
|
Document mpq7932 power-management IC
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221207173716.123223-3-saravanan@linumiz.com
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control updates from Rafael Wysocki:
"The majority of changes here are related to the general switch-over to
using arrays of generic trip point structures registered along with a
thermal zone instead of trip point callbacks (this has been done
mostly by Daniel Lezcano with some help from yours truly on the Intel
drivers front).
Apart from that and the related reorganization of code, there are some
enhancements of the existing driver and a new Mediatek Low Voltage
Thermal Sensor (LVTS) driver. The Intel powerclamp undergoes a major
rework so it will use the generic idle_inject facility for CPU idle
time injection going forward and it will take additional module
parameters for specifying the subset of CPUs to be affected by it
(work done by Srinivas Pandruvada).
Also included are assorted fixes and a whole bunch of cleanups.
Specifics:
- Rework a large bunch of drivers to use the generic thermal trip
structure and use the opportunity to do more cleanups by removing
unused functions from the OF code (Daniel Lezcano)
- Remove core header inclusion from drivers (Daniel Lezcano)
- Fix some locking issues related to the generic thermal trip rework
(Johan Hovold)
- Fix a crash when requesting the critical temperature on tegra,
which is related to the generic trip point work (Jon Hunter)
- Clean up thermal device unregistration code (Viresh Kumar)
- Fix and clean up thermal control core initialization error code
paths (Daniel Lezcano)
- Relocate the trip points handling code into a separate file (Daniel
Lezcano)
- Make the thermal core fail registration of thermal zones and
cooling devices if the thermal class has not been registered
(Rafael Wysocki)
- Add trip point initialization helper functions for ACPI-defined
trip points and modify two thermal drivers to use them (Rafael
Wysocki, Daniel Lezcano)
- Make the core thermal control code use sysfs_emit_at() instead of
scnprintf() where applicable (ye xingchen)
- Consolidate code accessing the Intel TCC (Thermal Control
Circuitry) MSRs by introducing library functions for that and
making the TCC-related code in thermal drivers use them (Zhang Rui)
- Enhance the x86_pkg_temp_thermal driver to support dynamic tjmax
changes (Zhang Rui)
- Address an "unsigned expression compared with zero" warning in the
intel_soc_dts_iosf thermal driver (Yang Li)
- Update comments regarding two functions in the Intel Menlow thermal
driver (Deming Wang)
- Use sysfs_emit_at() instead of scnprintf() in the int340x thermal
driver (ye xingchen)
- Make the intel_pch thermal driver support the Wellsburg PCH (Tim
Zimmermann)
- Modify the intel_pch and processor_thermal_device_pci thermal
drivers use generic trip point tables instead of thermal zone trip
point callbacks (Daniel Lezcano)
- Add production mode attribute sysfs attribute to the int340x
thermal driver (Srinivas Pandruvada)
- Rework dynamic trip point updates handling and locking in the
int340x thermal driver (Rafael Wysocki)
- Make the int340x thermal driver use a generic trip points table
instead of thermal zone trip point callbacks (Rafael Wysocki,
Daniel Lezcano)
- Clean up and improve the int340x thermal driver (Rafael Wysocki)
- Simplify and clean up the intel_pch thermal driver (Rafael Wysocki)
- Fix the Intel powerclamp thermal driver and make it use the common
idle injection framework (Srinivas Pandruvada)
- Add two module parameters, cpumask and max_idle, to the Intel
powerclamp thermal driver to allow it to affect only a specific
subset of CPUs instead of all of them (Srinivas Pandruvada)
- Make the Intel quark_dts thermal driver Use generic trip point
objects instead of its own trip point representation (Daniel
Lezcano)
- Add toctree entry for thermal documents and fix two issues in the
Intel powerclamp driver documentation (Bagas Sanjaya)
- Use strscpy() to instead of strncpy() in the thermal core (Xu
Panda)
- Fix thermal_sampling_exit() (Vincent Guittot)
- Add Mediatek Low Voltage Thermal Sensor (LVTS) driver (Balsam
Chihi)
- Add r8a779g0 RCar support to the rcar_gen3 thermal driver (Geert
Uytterhoeven)
- Fix useless call to set_trips() when resuming in the rcar_gen3
thermal control driver and add interrupt support detection at init
time to it (Niklas Söderlund)
- Fix memory corruption in the hi3660 thermal driver (Yongqin Liu)
- Fix include path for libnl3 in pkg-config file for libthermal
(Vibhav Pant)
- Remove syscfg-based driver for st as the platform is not supported
any more (Alain Volmat)"
* tag 'thermal-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (135 commits)
thermal/drivers/st: Remove syscfg based driver
thermal: Remove core header inclusion from drivers
tools/lib/thermal: Fix include path for libnl3 in pkg-config file.
thermal/drivers/hisi: Drop second sensor hi3660
thermal/drivers/rcar_gen3_thermal: Fix device initialization
thermal/drivers/rcar_gen3_thermal: Create device local ops struct
thermal/drivers/rcar_gen3_thermal: Do not call set_trips() when resuming
thermal/drivers/rcar_gen3: Add support for R-Car V4H
dt-bindings: thermal: rcar-gen3-thermal: Add r8a779g0 support
thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver
dt-bindings: thermal: mediatek: Add LVTS thermal controllers
thermal/drivers/mediatek: Relocate driver to mediatek folder
tools/lib/thermal: Fix thermal_sampling_exit()
Documentation: powerclamp: Fix numbered lists formatting
Documentation: powerclamp: Escape wildcard in cpumask description
Documentation: admin-guide: Add toctree entry for thermal docs
thermal: intel: powerclamp: Add two module parameters
Documentation: admin-guide: Move intel_powerclamp documentation
thermal: core: Use sysfs_emit_at() instead of scnprintf()
thermal: intel: powerclamp: Fix duration module parameter
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These add EPP support to the AMD P-state cpufreq driver, add support
for new platforms to the Intel RAPL power capping driver, intel_idle
and the Qualcomm cpufreq driver, enable thermal cooling for Tegra194,
drop the custom cpufreq driver for loongson1 that is not necessary any
more (and the corresponding cpufreq platform device), fix assorted
issues and clean up code.
Specifics:
- Add EPP support to the AMD P-state cpufreq driver (Perry Yuan, Wyes
Karny, Arnd Bergmann, Bagas Sanjaya)
- Drop the custom cpufreq driver for loongson1 that is not necessary
any more and the corresponding cpufreq platform device (Keguang
Zhang)
- Remove "select SRCU" from system sleep, cpufreq and OPP Kconfig
entries (Paul E. McKenney)
- Enable thermal cooling for Tegra194 (Yi-Wei Wang)
- Register module device table and add missing compatibles for
cpufreq-qcom-hw (Nícolas F. R. A. Prado, Abel Vesa and Luca Weiss)
- Various dt binding updates for qcom-cpufreq-nvmem and
opp-v2-kryo-cpu (Christian Marangi)
- Make kobj_type structure in the cpufreq core constant (Thomas
Weißschuh)
- Make cpufreq_unregister_driver() return void (Uwe Kleine-König)
- Make the TEO cpuidle governor check CPU utilization in order to
refine idle state selection (Kajetan Puchalski)
- Make Kconfig select the haltpoll cpuidle governor when the haltpoll
cpuidle driver is selected and replace a default_idle() call in
that driver with arch_cpu_idle() to allow MWAIT to be used (Li
RongQing)
- Add Emerald Rapids Xeon support to the intel_idle driver (Artem
Bityutskiy)
- Add ARCH_SUSPEND_POSSIBLE dependencies for ARMv4 cpuidle drivers to
avoid randconfig build failures (Arnd Bergmann)
- Make kobj_type structures used in the cpuidle sysfs interface
constant (Thomas Weißschuh)
- Make the cpuidle driver registration code update microsecond values
of idle state parameters in accordance with their nanosecond values
if they are provided (Rafael Wysocki)
- Make the PSCI cpuidle driver prevent topology CPUs from being
suspended on PREEMPT_RT (Krzysztof Kozlowski)
- Document that pm_runtime_force_suspend() cannot be used with
DPM_FLAG_SMART_SUSPEND (Richard Fitzgerald)
- Add EXPORT macros for exporting PM functions from drivers (Richard
Fitzgerald)
- Remove /** from non-kernel-doc comments in hibernation code (Randy
Dunlap)
- Fix possible name leak in powercap_register_zone() (Yang Yingliang)
- Add Meteor Lake and Emerald Rapids support to the intel_rapl power
capping driver (Zhang Rui)
- Modify the idle_inject power capping facility to support 100% idle
injection (Srinivas Pandruvada)
- Fix large time windows handling in the intel_rapl power capping
driver (Zhang Rui)
- Fix memory leaks with using debugfs_lookup() in the generic PM
domains and Energy Model code (Greg Kroah-Hartman)
- Add missing 'cache-unified' property in the example for kryo OPP
bindings (Rob Herring)
- Fix error checking in opp_migrate_dentry() (Qi Zheng)
- Let qcom,opp-fuse-level be a 2-long array for qcom SoCs (Konrad
Dybcio)
- Modify some power management utilities to use the canonical ftrace
path (Ross Zwisler)
- Correct spelling problems for Documentation/power/ as reported by
codespell (Randy Dunlap)"
* tag 'pm-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (53 commits)
Documentation: amd-pstate: disambiguate user space sections
cpufreq: amd-pstate: Fix invalid write to MSR_AMD_CPPC_REQ
dt-bindings: opp: opp-v2-kryo-cpu: enlarge opp-supported-hw maximum
dt-bindings: cpufreq: qcom-cpufreq-nvmem: make cpr bindings optional
dt-bindings: cpufreq: qcom-cpufreq-nvmem: specify supported opp tables
PM: Add EXPORT macros for exporting PM functions
cpuidle: psci: Do not suspend topology CPUs on PREEMPT_RT
MIPS: loongson32: Drop obsolete cpufreq platform device
powercap: intel_rapl: Fix handling for large time window
cpuidle: driver: Update microsecond values of state parameters as needed
cpuidle: sysfs: make kobj_type structures constant
cpuidle: add ARCH_SUSPEND_POSSIBLE dependencies
PM: EM: fix memory leak with using debugfs_lookup()
PM: domains: fix memory leak with using debugfs_lookup()
cpufreq: Make kobj_type structure constant
cpufreq: davinci: Fix clk use after free
cpufreq: amd-pstate: avoid uninitialized variable use
cpufreq: Make cpufreq_unregister_driver() return void
OPP: fix error checking in opp_migrate_dentry()
dt-bindings: cpufreq: cpufreq-qcom-hw: Add SM8550 compatible
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"Updates for timekeeping, timers and clockevent/source drivers:
Core:
- Yet another round of improvements to make the clocksource watchdog
more robust:
- Relax the clocksource-watchdog skew criteria to match the NTP
criteria.
- Temporarily skip the watchdog when high memory latencies are
detected which can lead to false-positives.
- Provide an option to enable TSC skew detection even on systems
where TSC is marked as reliable.
Sigh!
- Initialize the restart block in the nanosleep syscalls to be
directed to the no restart function instead of doing a partial
setup on entry.
This prevents an erroneous restart_syscall() invocation from
corrupting user space data. While such a situation is clearly a
user space bug, preventing this is a correctness issue and caters
to the least suprise principle.
- Ignore the hrtimer slack for realtime tasks in schedule_hrtimeout()
to align it with the nanosleep semantics.
Drivers:
- The obligatory new driver bindings for Mediatek, Rockchip and
RISC-V variants.
- Add support for the C3STOP misfeature to the RISC-V timer to handle
the case where the timer stops in deeper idle state.
- Set up a static key in the RISC-V timer correctly before first use.
- The usual small improvements and fixes all over the place"
* tag 'timers-core-2023-02-20' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (30 commits)
clocksource/drivers/timer-sun4i: Add CLOCK_EVT_FEAT_DYNIRQ
clocksource/drivers/em_sti: Mark driver as non-removable
clocksource/drivers/sh_tmu: Mark driver as non-removable
clocksource/drivers/riscv: Patch riscv_clock_next_event() jump before first use
clocksource/drivers/timer-microchip-pit64b: Add delay timer
clocksource/drivers/timer-microchip-pit64b: Select driver only on ARM
dt-bindings: timer: sifive,clint: add comaptibles for T-Head's C9xx
dt-bindings: timer: mediatek,mtk-timer: add MT8365
clocksource/drivers/riscv: Get rid of clocksource_arch_init() callback
clocksource/drivers/sh_cmt: Mark driver as non-removable
clocksource/drivers/timer-microchip-pit64b: Drop obsolete dependency on COMPILE_TEST
clocksource/drivers/riscv: Increase the clock source rating
clocksource/drivers/timer-riscv: Set CLOCK_EVT_FEAT_C3STOP based on DT
dt-bindings: timer: Add bindings for the RISC-V timer device
RISC-V: time: initialize hrtimer based broadcast clock event device
dt-bindings: timer: rk-timer: Add rktimer for rv1126
time/debug: Fix memory leak with using debugfs_lookup()
clocksource: Enable TSC watchdog checking of HPET and PMTMR only when requested
posix-timers: Use atomic64_try_cmpxchg() in __update_gt_cputime()
clocksource: Verify HPET and PMTMR when TSC unverified
...
|
|
Sagar's email listed in maintainers is bouncing as his division was sold
off by the company. I attempted to contact him some days ago on what the
bounce email told me was his new contact information, but am yet to
receive a response.
Paul and Palmer are listed on each of the bindings, both of whom were
alive & well as of Wednesday so the bindings remain maintained.
CC: Sagar Kadam <sagar.kadam@openfive.com>
CC: Sagar Kadam <sagar.kadam@sifive.com>
Link: https://lore.kernel.org/all/785425ca-4000-a7e4-16d6-4d68c91b158d@kernel.org/
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Link: https://lore.kernel.org/r/20230217180035.39658-1-conor@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Add compatible for sm8450 IMEM.
Signed-off-by: Mukesh Ojha <quic_mojha@quicinc.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/1676986616-21378-1-git-send-email-quic_mojha@quicinc.com
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Convert the Loongson1 interrupt controller dt-bindings to json-schema.
Signed-off-by: Keguang Zhang <keguang.zhang@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230221102545.2103632-1-keguang.zhang@gmail.com
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC updates from Borislav Petkov:
- Add a driver for the RAS functionality on Xilinx's on chip memory
controller
- Add support for decoding errors from the first and second level
memory on SKL-based hardware
- Add support for the memory controllers in Intel Granite Rapids and
Emerald Rapids machines
- First round of amd64_edac driver simplification and removal of
unneeded functionality
- The usual cleanups and fixes
* tag 'edac_updates_for_v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/amd64: Shut up an -Werror,-Wsometimes-uninitialized clang false positive
EDAC/amd64: Remove early_channel_count()
EDAC/amd64: Remove PCI Function 0
EDAC/amd64: Remove PCI Function 6
EDAC/amd64: Remove scrub rate control for Family 17h and later
EDAC/amd64: Don't set up EDAC PCI control on Family 17h+
EDAC/i10nm: Add driver decoder for Sapphire Rapids server
EDAC/i10nm: Add Intel Granite Rapids server support
EDAC/i10nm: Make more configurations CPU model specific
EDAC/i10nm: Add Intel Emerald Rapids server support
EDAC/skx_common: Delete duplicated and unreachable code
EDAC/skx_common: Enable EDAC support for the "near" memory
EDAC/qcom: Add platform_device_id table for module autoloading
EDAC/zynqmp: Add EDAC support for Xilinx ZynqMP OCM
dt-bindings: edac: Add bindings for Xilinx ZynqMP OCM
|
|
Add compatibles for the Cortex-A715 and X3 cores found in some
recent flagship designs.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230216110803.3945747-1-konrad.dybcio@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Pull SoC DT updates from Arnd Bergmann:
"About a quarter of the changes are for 32-bit arm, mostly filling in
device support for existing machines and adding minor cleanups, mostly
for Qualcomm and Samsung based machines.
Two new 32-bit SoCs are added, both are quad-core Cortex-A7 chips from
Rockchips that have been around for a while but were lacking kernel
support so far: RV1126 is a Vision SoC with an NPU and is used in the
Edgeble Neural Compute Module 2(Neu2) board, while RK3128 is design
for TV boxes and so far only comes with a dts for its refernece
design.
The other 32-bit boards that were added are two ASpeed AST2600 based
BMC boards, the Microchip sam9x60_curiosity development board (Armv5
based!), the Enclustra PE1 FPGA-SoM baseboard, and a few more boards
for i.MX53 and i.MX6ULL.
On the RISC-V side, there are fewer patches, but a total of ten new
single-board computers based on variations of the Allwinner D1/T113
chip, plus one more board based on Microchip Polarfire.
As usual, arm64 has by far the most changes here, with over 700
non-merge changesets, among them over 400 alone for Qualcomm. The
newly added SoCs this time are all recent high-end embedded SoCs for
various markets, each on comes with support for its reference board:
- Qualcomm SM8550 (Snapdragon 8 Gen 2) for mobile phones
- Qualcomm QDU1000/QRU1000 5G RAN platform
- Rockchips RK3588/RK3588s for tablets, chromebooks and SBCs
- TI J784S4 for industrial and automotive applications
In total, there are 46 new arm64 machines:
- Reference platforms for each of the five new SoCs
- Three Amlogic based development boards
- Six embedded machines based on NXP i.MX8MM and i.MX8MP
- The Mediatek mt7986a based Banana Pi R3 router
- Six tablets based on Qualcomm MSM8916 (Snapdragon 410), SM6115
(Snapdragon 662) and SM8250 (Snapdragon 865)
- Two LTE dongles, also based on MSM8916
- Seven mobile phones, based on Qualcomm MSM8953 (Snapdragon 610),
SDM450 and SDM632
- Three chromebooks based on Qualcomm SC7280 (Snapdragon 7c)
- Nine development boards based on Rockchips RK3588, RK3568, RK3566
and RK3328.
- Five development machines based on TI K3 (AM642/AM654/AM68/AM69)
The cleanup of dtc warnings continues across all platforms, adding to
the total number of changes"
* tag 'soc-dt-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (1035 commits)
dt-bindings: riscv: correct starfive visionfive 2 compatibles
ARM: dts: socfpga: Add enclustra PE1 devicetree
dt-bindings: altera: Add enclustra mercury PE1
arm64: dts: qcom: msm8996: align RPM G-Link clock-controller node with bindings
arm64: dts: qcom: qcs404: align RPM G-Link node with bindings
arm64: dts: qcom: ipq6018: align RPM G-Link node with bindings
arm64: dts: qcom: sm8550: remove invalid interconnect property from cryptobam
arm64: dts: qcom: sc7280: Adjust zombie PWM frequency
arm64: dts: qcom: sc8280xp-pmics: Specify interrupt parent explicitly
arm64: dts: qcom: sm7225-fairphone-fp4: enable remaining i2c busses
arm64: dts: qcom: sm7225-fairphone-fp4: move status property down
arm64: dts: qcom: pmk8350: Use the correct PON compatible
arm64: dts: qcom: sc8280xp-x13s: Enable external display
arm64: dts: qcom: sc8280xp-crd: Introduce pmic_glink
arm64: dts: qcom: sc8280xp: Add USB-C-related DP blocks
arm64: dts: qcom: sm8350-hdk: enable GPU
arm64: dts: qcom: sm8350: add GPU, GMU, GPU CC and SMMU nodes
arm64: dts: qcom: sm8350: finish reordering nodes
arm64: dts: qcom: sm8350: move more nodes to correct place
arm64: dts: qcom: sm8350: reorder device nodes
...
|
|
Pull ARM SoC updates from Arnd Bergmann:
"The majority of the changes are for the OMAP2 platform, mostly
removing some dead code that got left behind from previous cleanups.
Aside from that, there are very minor updates and correctness fixes
for Zynq, i.MX, Samsung, Broadcom, AT91, ep93xx, and OMAP1"
* tag 'arm-soc-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (26 commits)
dt-bindings: soc: samsung: exynos-pmu: allow phys as child
ARM: imx: mach-imx6ul: add imx6ulz support
ARM: imx: Call ida_simple_remove() for ida_simple_get
arm64: drop redundant "ARMv8" from Kconfig option title
ARM: ep93xx: Convert to use descriptors for GPIO LEDs
ARM: s3c: fix s3c64xx_set_timer_source prototype
ARM: OMAP2+: Fix spelling typos in comment
ARM: OMAP2+: Remove unneeded #include <linux/pinctrl/machine.h>
ARM: OMAP2+: Remove unneeded #include <linux/pinctrl/pinmux.h>
ARM: OMAP1: call platform_device_put() in error case in omap1_dm_timer_init()
ARM: BCM63xx: remove useless goto statement
ARM: omap2: make functions static
ARM: omap2: remove unused omap2_pm_init
ARM: omap2: remove unused declarations
ARM: omap2: remove unused functions
ARM: omap2: smartreflex: remove on_init control
ARM: omap2: remove APLL control
ARM: omap2: simplify clock2xxx header
ARM: omap2: remove unused omap_hwmod_reset.c
ARM: omap2: remove unused headers
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC boardfile updates from Arnd Bergmann
"Unused boardfile removal for 6.3
This is a follow-up to the deprecation of most of the old-style board
files that was merged in linux-6.0, removing them for good.
This branch is almost exclusively dead code removal based on those
annotations. Some device driver removals went through separate
subsystem trees, but the majority is in the same branch, in order to
better handle dependencies between the patches and avoid breaking
bisection.
Unfortunately that leads to merge conflicts against other changes in
the subsystem trees, but they should all be trivial to resolve by
removing the files.
See commit 7d0d3fa7339e ("Merge tag 'arm-boardfiles-6.0' of
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc") for the
description of which machines were marked unused and are now removed.
The only removals that got postponed are Terastation WXL (mv78xx0) and
Jornada720 (StrongARM1100), which turned out to still have potential
users"
* tag 'arm-boardfile-remove-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (91 commits)
mmc: omap: drop TPS65010 dependency
ARM: pxa: restore mfp-pxa320.h
usb: ohci-omap: avoid unused-variable warning
ARM: debug: remove references in DEBUG_UART_8250_SHIFT to removed configs
ARM: s3c: remove obsolete s3c-cpu-freq header
MAINTAINERS: adjust SAMSUNG SOC CLOCK DRIVERS after s3c24xx support removal
MAINTAINERS: update file entries after arm multi-platform rework and mach-pxa removal
ARM: remove CONFIG_UNUSED_BOARD_FILES
mfd: remove htc-pasic3 driver
w1: remove ds1wm driver
usb: remove ohci-tmio driver
fbdev: remove w100fb driver
fbdev: remove tmiofb driver
mmc: remove tmio_mmc driver
mfd: remove ucb1400 support
mfd: remove toshiba tmio drivers
rtc: remove v3020 driver
power: remove pda_power supply driver
ASoC: pxa: remove unused board support
pcmcia: remove unused pxa/sa1100 drivers
...
|
|
'x86/vt-d', 'x86/amd' and 'core' into next
|
|
QSPI on Qualcomm SDM845, SC7180 and SC7280 SoCs uses OPP table (both in
DTS and Linux driver) and is suuplied by CX power domain. Document
missing properties to fix:
sc7280-idp2.dtb: spi@88dc000: Unevaluated properties are not allowed ('operating-points-v2', 'power-domains' were unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230217155802.848178-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Using "va" and "vb" doesn't match what's written on the board, or the
communications from StarFive.
Switching to using the silkscreened version number will ease confusion &
the risk of another spin of the board containing a "conflicting" version
identifier.
As the binding has not made it into mainline yet, take the opportunity
to "correct" things.
Suggested-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Link: https://lore.kernel.org/linux-riscv/Y+4AxDSDLyL1WAqh@wendy/
Fixes: 97b7ed072784 ("dt-bindings: riscv: Add StarFive JH7110 SoC and VisionFive 2 board")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230216131511.3327943-1-conor.dooley@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
