| Age | Commit message (Collapse) | Author |
|---|
|
Use the standard name for the gpion in DT: reset-gpios
Document that the RST line is low active and update the example
accordingly.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191120131753.6831-2-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The tlv320aic31xx devices allow to adjust the output common-mode voltage
for best analog performance. The datasheet states that the common mode
voltage should be set to be <= AVDD/2.
This changes allows to configure the output common-mode voltage via a DT
property. If the property is absent the voltage is automatically chosen
as the highest voltage below/equal to AVDD/2.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20191118151207.28576-1-l.stach@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On boards where the RST line is not pulled up, but it is connected to a
GPIO line this property must present in order to be able to enable the
codec.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113124734.27984-2-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
'fsia' and 'fsib' property prefixes were added as schema in commit
2f52475bac7e ("ASoC: fsi: switch to yaml base Documentation").
Unfortunately to do checks on actual vendor prefixes, we have to track
the handful of prefixes which are not vendors like 'fsia' and 'fsib'.
Fixes: 2f52475bac7e ASoC: fsi: switch to yaml base Documentation
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191108153538.11970-1-robh@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch switches from .txt base to .yaml base Document for FSI.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/878sp4jaqy.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The ADAU7118 has an example where the codec has an i2c address of 14, and
the unit address set to 14 as well.
However, while the address is expressed in decimal, the unit-address is
supposed to be in hexadecimal, which ends up with two different addresses
that trigger a DTC warning. Fix this by setting the address to 0x14.
Cc: Nuno Sá <nuno.sa@analog.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Fixes: 969d49b2cdc8 ("dt-bindings: asoc: Add ADAU7118 documentation")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191105105615.21391-1-maxime@cerno.tech
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The btndet-delay device property could control the HW debounce time.
It is easy to adjust the sensitivity of push button.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20191030085556.14351-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add one optional property "rockchip,hdmi-codec" to let user specify HDMI
device node in DTS so machine driver can find hdmi-codec device node for
HDMI codec DAI.
Use the presence of rockchip,audio-codec and rockchip,hdmi-codec to
specify the use case.
Use max98090 only : specify rockchip,audio-codec.
Use HDMI only: specify rockchip,hdmi-codec.
Use both max98090 and HDMI: specify rockchip,audio-codec and
rockchip,hdmi-codec.
Move these properties to optional because they are not needed for
HDMI-only use case.
"rockchip,audio-codec": The phandle of the MAX98090 audio codec
"rockchip,headset-codec": The phandle of Ext chip for jack detection
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Link: https://lore.kernel.org/r/20191028071930.145899-3-cychiang@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This changes are in accordance with the review done to this bindings.
This is a follow-up patch to 969d49b2cdc8.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20191021140816.262401-2-nuno.sa@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add an optional property "ec-codec". If specified, mt8183 could use the
"wake on voice" feature offered by EC codec.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20191019143504.3.Iec97a3f137148cdf316056612590b3e0b302f5f3@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
- Add "reg" for binding to shared memory exposed by EC.
- Add "memory-region" for binding to memory region shared by AP.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20191017213539.06.I0df85fe54162426e31f60a589d9b461c65df2faa@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Read max DMIC gain from EC codec instead of DTS. Also removes the
dt-binding of max-dmic-gain.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20191017213539.05.Id4657c864d544634f2b5c1c9b34fa8232ecba44d@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Convert Samsung I2S controller to newer dt-schema format.
Signed-off-by: Maciej Falkowski <m.falkowski@samsung.com>
[mszyprow: integrated fix for minor spelling issues]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191004125914.1033-1-m.szyprowski@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
dt-schema
Convert Samsung Exynos Odroid XU3/XU4 audio complex with MAX98090 codec
to newer dt-schema format.
'clocks' property is unneeded in the bindings and is left undefined in 'properties'.
'samsung,audio-widgets' and 'samsung,audio-routing' are optional from driver
perspective and they are set as unrequired.
Signed-off-by: Maciej Falkowski <m.falkowski@samsung.com>
[mszyprow: reordered non-standard properties]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191017100529.4183-1-m.szyprowski@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The Allwinner SoCs have an embedded audio codec that is supported in Linux,
with a matching Device Tree binding.
Now that we have the DT validation in place, let's convert the device tree
bindings for that controller over to a YAML schemas.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191016104355.65169-1-mripard@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Typically, the r0 (calibration data) and temperature were measured in the factory.
This information is written into the non-volatile area
where keeps data whether factory reset or OS update.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20191016115617.23213-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Document the ADAU7118 8 channel PDM to I2S/TDM converter devicetree
bindings.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20191010074234.7344-2-nuno.sa@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add the DT binding for the TAS2562 amplifier.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20191008181517.5332-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch add property "resets" && "reset-names" in examples so that we can
use reset controller to reset audio domain regs.
Signed-off-by: Jiaxin Yu <jiaxin.yu@mediatek.com>
Link: https://lore.kernel.org/r/1569580317-21181-4-git-send-email-jiaxin.yu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Document SoC specific bindings for RZ/G2N (r8a774b1) SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Link: https://lore.kernel.org/r/1570171940-42937-1-git-send-email-biju.das@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add tas2770 smart PA dt bindings
Signed-off-by: Frank Shi <shifu0704@thundersoft.com>
Link: https://lore.kernel.org/r/1568962709-19185-1-git-send-email-shifu0704@thundersoft.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add compatible string for boards with WM1811 CODEC to the list.
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Link: https://lore.kernel.org/r/20190920130218.32690-7-s.nawrocki@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Headset codec is optional. Add missing update to DT binding document.
Fixes: a962a809e5e4 ("ASoC: mediatek: mt8183: make headset codec optional")
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20190920112320.166052-1-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The Allwinner A23 SoC and later have an embedded audio codec that uses a
separate controller to drive its analog part, which is supported in Linux,
with a matching Device Tree binding.
Now that we have the DT validation in place, let's convert the device tree
bindings for that controller over to a YAML schemas.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20190906151221.3148-2-mripard@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add the DT binding documentation for NXP MQS driver
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/65e1f035aea2951aacda54aa3a751bc244f72f6a.1568367274.git.shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull Documentation/process update from Greg KH:
"Here are two small Documentation/process/embargoed-hardware-issues.rst
file updates that missed my previous char/misc pull request.
The first one adds an Intel representative for the process, and the
second one cleans up the text a bit more when it comes to how the
disclosure rules work, as it was a bit confusing to some companies"
* tag 'char-misc-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Documentation/process: Clarify disclosure rules
Documentation/process: Volunteer as the ambassador for Intel
|
|
The role of the contact list provided by the disclosing party and how it
affects the disclosure process and the ability to include experts into
the development process is not really well explained.
Neither is it entirely clear when the disclosing party will be informed
about the fact that a developer who is not covered by an employer NDA needs
to be brought in and disclosed.
Explain the role of the contact list and the information policy along with
an eventual conflict resolution better.
Reported-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.1909251028390.10825@nanos.tec.linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull networking fixes from David Miller:
1) Sanity check URB networking device parameters to avoid divide by
zero, from Oliver Neukum.
2) Disable global multicast filter in NCSI, otherwise LLDP and IPV6
don't work properly. Longer term this needs a better fix tho. From
Vijay Khemka.
3) Small fixes to selftests (use ping when ping6 is not present, etc.)
from David Ahern.
4) Bring back rt_uses_gateway member of struct rtable, it's semantics
were not well understood and trying to remove it broke things. From
David Ahern.
5) Move usbnet snaity checking, ignore endpoints with invalid
wMaxPacketSize. From Bjørn Mork.
6) Missing Kconfig deps for sja1105 driver, from Mao Wenan.
7) Various small fixes to the mlx5 DR steering code, from Alaa Hleihel,
Alex Vesker, and Yevgeny Kliteynik
8) Missing CAP_NET_RAW checks in various places, from Ori Nimron.
9) Fix crash when removing sch_cbs entry while offloading is enabled,
from Vinicius Costa Gomes.
10) Signedness bug fixes, generally in looking at the result given by
of_get_phy_mode() and friends. From Dan Crapenter.
11) Disable preemption around BPF_PROG_RUN() calls, from Eric Dumazet.
12) Don't create VRF ipv6 rules if ipv6 is disabled, from David Ahern.
13) Fix quantization code in tcp_bbr, from Kevin Yang.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (127 commits)
net: tap: clean up an indentation issue
nfp: abm: fix memory leak in nfp_abm_u32_knode_replace
tcp: better handle TCP_USER_TIMEOUT in SYN_SENT state
sk_buff: drop all skb extensions on free and skb scrubbing
tcp_bbr: fix quantization code to not raise cwnd if not probing bandwidth
mlxsw: spectrum_flower: Fail in case user specifies multiple mirror actions
Documentation: Clarify trap's description
mlxsw: spectrum: Clear VLAN filters during port initialization
net: ena: clean up indentation issue
NFC: st95hf: clean up indentation issue
net: phy: micrel: add Asym Pause workaround for KSZ9021
net: socionext: ave: Avoid using netdev_err() before calling register_netdev()
ptp: correctly disable flags on old ioctls
lib: dimlib: fix help text typos
net: dsa: microchip: Always set regmap stride to 1
nfp: flower: fix memory leak in nfp_flower_spawn_vnic_reprs
nfp: flower: prevent memory leak in nfp_flower_spawn_phy_reprs
net/sched: Set default of CONFIG_NET_TC_SKB_EXT to N
vrf: Do not attempt to create IPv6 mcast rule if IPv6 is disabled
net: sched: sch_sfb: don't call qdisc_put() while holding tree lock
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull kernel lockdown mode from James Morris:
"This is the latest iteration of the kernel lockdown patchset, from
Matthew Garrett, David Howells and others.
From the original description:
This patchset introduces an optional kernel lockdown feature,
intended to strengthen the boundary between UID 0 and the kernel.
When enabled, various pieces of kernel functionality are restricted.
Applications that rely on low-level access to either hardware or the
kernel may cease working as a result - therefore this should not be
enabled without appropriate evaluation beforehand.
The majority of mainstream distributions have been carrying variants
of this patchset for many years now, so there's value in providing a
doesn't meet every distribution requirement, but gets us much closer
to not requiring external patches.
There are two major changes since this was last proposed for mainline:
- Separating lockdown from EFI secure boot. Background discussion is
covered here: https://lwn.net/Articles/751061/
- Implementation as an LSM, with a default stackable lockdown LSM
module. This allows the lockdown feature to be policy-driven,
rather than encoding an implicit policy within the mechanism.
The new locked_down LSM hook is provided to allow LSMs to make a
policy decision around whether kernel functionality that would allow
tampering with or examining the runtime state of the kernel should be
permitted.
The included lockdown LSM provides an implementation with a simple
policy intended for general purpose use. This policy provides a coarse
level of granularity, controllable via the kernel command line:
lockdown={integrity|confidentiality}
Enable the kernel lockdown feature. If set to integrity, kernel features
that allow userland to modify the running kernel are disabled. If set to
confidentiality, kernel features that allow userland to extract
confidential information from the kernel are also disabled.
This may also be controlled via /sys/kernel/security/lockdown and
overriden by kernel configuration.
New or existing LSMs may implement finer-grained controls of the
lockdown features. Refer to the lockdown_reason documentation in
include/linux/security.h for details.
The lockdown feature has had signficant design feedback and review
across many subsystems. This code has been in linux-next for some
weeks, with a few fixes applied along the way.
Stephen Rothwell noted that commit 9d1f8be5cf42 ("bpf: Restrict bpf
when kernel lockdown is in confidentiality mode") is missing a
Signed-off-by from its author. Matthew responded that he is providing
this under category (c) of the DCO"
* 'next-lockdown' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (31 commits)
kexec: Fix file verification on S390
security: constify some arrays in lockdown LSM
lockdown: Print current->comm in restriction messages
efi: Restrict efivar_ssdt_load when the kernel is locked down
tracefs: Restrict tracefs when the kernel is locked down
debugfs: Restrict debugfs when the kernel is locked down
kexec: Allow kexec_file() with appropriate IMA policy when locked down
lockdown: Lock down perf when in confidentiality mode
bpf: Restrict bpf when kernel lockdown is in confidentiality mode
lockdown: Lock down tracing and perf kprobes when in confidentiality mode
lockdown: Lock down /proc/kcore
x86/mmiotrace: Lock down the testmmiotrace module
lockdown: Lock down module params that specify hardware parameters (eg. ioport)
lockdown: Lock down TIOCSSERIAL
lockdown: Prohibit PCMCIA CIS storage when the kernel is locked down
acpi: Disable ACPI table override if the kernel is locked down
acpi: Ignore acpi_rsdp kernel param when the kernel has been locked down
ACPI: Limit access to custom_method when the kernel is locked down
x86/msr: Restrict MSR access when the kernel is locked down
x86: Lock down IO port access when the kernel is locked down
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity
Pull integrity updates from Mimi Zohar:
"The major feature in this time is IMA support for measuring and
appraising appended file signatures. In addition are a couple of bug
fixes and code cleanup to use struct_size().
In addition to the PE/COFF and IMA xattr signatures, the kexec kernel
image may be signed with an appended signature, using the same
scripts/sign-file tool that is used to sign kernel modules.
Similarly, the initramfs may contain an appended signature.
This contained a lot of refactoring of the existing appended signature
verification code, so that IMA could retain the existing framework of
calculating the file hash once, storing it in the IMA measurement list
and extending the TPM, verifying the file's integrity based on a file
hash or signature (eg. xattrs), and adding an audit record containing
the file hash, all based on policy. (The IMA support for appended
signatures patch set was posted and reviewed 11 times.)
The support for appended signature paves the way for adding other
signature verification methods, such as fs-verity, based on a single
system-wide policy. The file hash used for verifying the signature and
the signature, itself, can be included in the IMA measurement list"
* 'next-integrity' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity:
ima: ima_api: Use struct_size() in kzalloc()
ima: use struct_size() in kzalloc()
sefltest/ima: support appended signatures (modsig)
ima: Fix use after free in ima_read_modsig()
MODSIGN: make new include file self contained
ima: fix freeing ongoing ahash_request
ima: always return negative code for error
ima: Store the measurement again when appraising a modsig
ima: Define ima-modsig template
ima: Collect modsig
ima: Implement support for module-style appended signatures
ima: Factor xattr_verify() out of ima_appraise_measurement()
ima: Add modsig appraise_type option for module-style appended signatures
integrity: Select CONFIG_KEYS instead of depending on it
PKCS#7: Introduce pkcs7_get_digest()
PKCS#7: Refactor verify_pkcs7_signature()
MODSIGN: Export module signature definitions
ima: initialize the "template" field with the default template
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
Pull fuse virtio-fs support from Miklos Szeredi:
"Virtio-fs allows exporting directory trees on the host and mounting
them in guest(s).
This isn't actually a new filesystem, but a glue layer between the
fuse filesystem and a virtio based back-end.
It's similar in functionality to the existing virtio-9p solution, but
significantly faster in benchmarks and has better POSIX compliance.
Further permformance improvements can be achieved by sharing the page
cache between host and guest, allowing for faster I/O and reduced
memory use.
Kata Containers have been including the out-of-tree virtio-fs (with
the shared page cache patches as well) since version 1.7 as an
experimental feature. They have been active in development and plan to
switch from virtio-9p to virtio-fs as their default solution. There
has been interest from other sources as well.
The userspace infrastructure is slated to be merged into qemu once the
kernel part hits mainline.
This was developed by Vivek Goyal, Dave Gilbert and Stefan Hajnoczi"
* tag 'virtio-fs-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
virtio-fs: add virtiofs filesystem
virtio-fs: add Documentation/filesystems/virtiofs.rst
fuse: reserve values for mapping protocol
|
|
Pull more KVM updates from Paolo Bonzini:
"x86 KVM changes:
- The usual accuracy improvements for nested virtualization
- The usual round of code cleanups from Sean
- Added back optimizations that were prematurely removed in 5.2 (the
bare minimum needed to fix the regression was in 5.3-rc8, here
comes the rest)
- Support for UMWAIT/UMONITOR/TPAUSE
- Direct L2->L0 TLB flushing when L0 is Hyper-V and L1 is KVM
- Tell Windows guests if SMT is disabled on the host
- More accurate detection of vmexit cost
- Revert a pvqspinlock pessimization"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (56 commits)
KVM: nVMX: cleanup and fix host 64-bit mode checks
KVM: vmx: fix build warnings in hv_enable_direct_tlbflush() on i386
KVM: x86: Don't check kvm_rebooting in __kvm_handle_fault_on_reboot()
KVM: x86: Drop ____kvm_handle_fault_on_reboot()
KVM: VMX: Add error handling to VMREAD helper
KVM: VMX: Optimize VMX instruction error and fault handling
KVM: x86: Check kvm_rebooting in kvm_spurious_fault()
KVM: selftests: fix ucall on x86
Revert "locking/pvqspinlock: Don't wait if vCPU is preempted"
kvm: nvmx: limit atomic switch MSRs
kvm: svm: Intercept RDPRU
kvm: x86: Add "significant index" flag to a few CPUID leaves
KVM: x86/mmu: Skip invalid pages during zapping iff root_count is zero
KVM: x86/mmu: Explicitly track only a single invalid mmu generation
KVM: x86/mmu: Revert "KVM: x86/mmu: Remove is_obsolete() call"
KVM: x86/mmu: Revert "Revert "KVM: MMU: reclaim the zapped-obsolete page first""
KVM: x86/mmu: Revert "Revert "KVM: MMU: collapse TLB flushes when zap all pages""
KVM: x86/mmu: Revert "Revert "KVM: MMU: zap pages in batch""
KVM: x86/mmu: Revert "Revert "KVM: MMU: add tracepoint for kvm_mmu_invalidate_all_pages""
KVM: x86/mmu: Revert "Revert "KVM: MMU: show mmu_valid_gen in shadow page related tracepoints""
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"Besides one new driver being added for the PWM controller found in
various Spreadtrum SoCs, this series of changes brings a slew of,
mostly minor, fixes and cleanups for existing drivers, as well as some
enhancements to the core code.
Lastly, Uwe is added to the PWM subsystem entry of the MAINTAINERS
file, making official his role as a reviewer"
* tag 'pwm/for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (34 commits)
MAINTAINERS: Add myself as reviewer for the PWM subsystem
MAINTAINERS: Add patchwork link for PWM entry
MAINTAINERS: Add a selection of PWM related keywords to the PWM entry
pwm: mediatek: Add MT7629 compatible string
dt-bindings: pwm: Update bindings for MT7629 SoC
pwm: mediatek: Update license and switch to SPDX tag
pwm: mediatek: Use pwm_mediatek as common prefix
pwm: mediatek: Allocate the clks array dynamically
pwm: mediatek: Remove the has_clks field
pwm: mediatek: Drop the check for of_device_get_match_data()
pwm: atmel: Consolidate driver data initialization
pwm: atmel: Remove unneeded check for match data
pwm: atmel: Remove platform_device_id and use only dt bindings
pwm: stm32-lp: Add check in case requested period cannot be achieved
pwm: Ensure pwm_apply_state() doesn't modify the state argument
pwm: fsl-ftm: Don't update the state for the caller of pwm_apply_state()
pwm: sun4i: Don't update the state for the caller of pwm_apply_state()
pwm: rockchip: Don't update the state for the caller of pwm_apply_state()
pwm: Let pwm_get_state() return the last implemented state
pwm: Introduce local struct pwm_chip in pwm_apply_state()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management updates from Zhang Rui:
- Add Amit Kucheria as thermal subsystem Reviewer (Amit Kucheria)
- Fix a use after free bug when unregistering thermal zone devices (Ido
Schimmel)
- Fix thermal core framework to use put_device() when device_register()
fails (Yue Hu)
- Enable intel_pch_thermal and MMIO RAPL support for Intel Icelake
platform (Srinivas Pandruvada)
- Add clock operations in qorip thermal driver, for some platforms with
clock control like i.MX8MQ (Anson Huang)
- A couple of trivial fixes and cleanups for thermal core and different
soc thermal drivers (Amit Kucheria, Christophe JAILLET, Chuhong Yuan,
Fuqian Huang, Kelsey Skunberg, Nathan Huckleberry, Rishi Gupta,
Srinivas Kandagatla)
* 'for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
MAINTAINERS: Add Amit Kucheria as reviewer for thermal
thermal: Add some error messages
thermal: Fix use-after-free when unregistering thermal zone device
thermal/drivers/core: Use put_device() if device_register() fails
thermal_hwmon: Sanitize thermal_zone type
thermal: intel: Use dev_get_drvdata
thermal: intel: int3403: replace printk(KERN_WARN...) with pr_warn(...)
thermal: intel: int340x_thermal: Remove unnecessary acpi_has_method() uses
thermal: int340x: processor_thermal: Add Ice Lake support
drivers: thermal: qcom: tsens: Fix memory leak from qfprom read
thermal: tegra: Fix a typo
thermal: rcar_gen3_thermal: Replace devm_add_action() followed by failure action with devm_add_action_or_reset()
thermal: armada: Fix -Wshift-negative-value
dt-bindings: thermal: qoriq: Add optional clocks property
thermal: qoriq: Use __maybe_unused instead of #if CONFIG_PM_SLEEP
thermal: qoriq: Use devm_platform_ioremap_resource() instead of of_iomap()
thermal: qoriq: Fix error path of calling qoriq_tmu_register_tmu_zone fail
thermal: qoriq: Add clock operations
drivers: thermal: processor_thermal_device: Export sysfs interface for TCC offset
|
|
Alex noted that the below description might not be obvious to all users.
Clarify it by adding an example.
Fixes: f3047ca01f12 ("Documentation: Add devlink-trap documentation")
Reported-by: Alex Kushnarov <alexanderk@mellanox.com>
Reviewed-by: Alex Kushnarov <alexanderk@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- addition of AST2600, i.MX7ULP and F81803 watchdog support
- removal of the w90x900 and ks8695 drivers
- ziirave_wdt improvements
- small fixes and improvements
* tag 'linux-watchdog-5.4-rc1' of git://www.linux-watchdog.org/linux-watchdog: (51 commits)
watchdog: f71808e_wdt: Add F81803 support
watchdog: qcom: remove unnecessary variable from private storage
watchdog: qcom: support pre-timeout when the bark irq is available
watchdog: imx_sc: this patch just fixes whitespaces
watchdog: apseed: Add access_cs0 option for alt-boot
watchdog: aspeed: add support for dual boot
watchdog: orion_wdt: use timer1 as a pretimeout
watchdog: Add i.MX7ULP watchdog support
dt-bindings: watchdog: Add i.MX7ULP bindings
dt-bindings: watchdog: sun4i: Add the watchdog clock
dt-bindings: watchdog: sun4i: Add the watchdog interrupts
dt-bindings: watchdog: Convert Allwinner watchdog to a schema
dt-bindings: watchdog: Add YAML schemas for the generic watchdog bindings
watchdog: aspeed: Add support for AST2600
dt-bindings: watchdog: Add ast2600 compatible
watchdog: ziirave_wdt: Update checked I2C functionality mask
watchdog: ziirave_wdt: Drop ziirave_firm_write_block_data()
watchdog: ziirave_wdt: Fix DOWNLOAD_START payload
watchdog: ziirave_wdt: Drop status polling code
watchdog: ziirave_wdt: Fix RESET_PROCESSOR payload
...
|
|
Merge more updates from Andrew Morton:
- almost all of the rest of -mm
- various other subsystems
Subsystems affected by this patch series:
memcg, misc, core-kernel, lib, checkpatch, reiserfs, fat, fork,
cpumask, kexec, uaccess, kconfig, kgdb, bug, ipc, lzo, kasan, madvise,
cleanups, pagemap
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (77 commits)
arch/sparc/include/asm/pgtable_64.h: fix build
mm: treewide: clarify pgtable_page_{ctor,dtor}() naming
ntfs: remove (un)?likely() from IS_ERR() conditions
IB/hfi1: remove unlikely() from IS_ERR*() condition
xfs: remove unlikely() from WARN_ON() condition
wimax/i2400m: remove unlikely() from WARN*() condition
fs: remove unlikely() from WARN_ON() condition
xen/events: remove unlikely() from WARN() condition
checkpatch: check for nested (un)?likely() calls
hexagon: drop empty and unused free_initrd_mem
mm: factor out common parts between MADV_COLD and MADV_PAGEOUT
mm: introduce MADV_PAGEOUT
mm: change PAGEREF_RECLAIM_CLEAN with PAGE_REFRECLAIM
mm: introduce MADV_COLD
mm: untag user pointers in mmap/munmap/mremap/brk
vfio/type1: untag user pointers in vaddr_get_pfn
tee/shm: untag user pointers in tee_shm_register
media/v4l2-core: untag user pointers in videobuf_dma_contig_user_get
drm/radeon: untag user pointers in radeon_gem_userptr_ioctl
drm/amdgpu: untag user pointers
...
|
|
The naming of pgtable_page_{ctor,dtor}() seems to have confused a few
people, and until recently arm64 used these erroneously/pointlessly for
other levels of page table.
To make it incredibly clear that these only apply to the PTE level, and to
align with the naming of pgtable_pmd_page_{ctor,dtor}(), let's rename them
to pgtable_pte_page_{ctor,dtor}().
These changes were generated with the following shell script:
----
git grep -lw 'pgtable_page_.tor' | while read FILE; do
sed -i '{s/pgtable_page_ctor/pgtable_pte_page_ctor/}' $FILE;
sed -i '{s/pgtable_page_dtor/pgtable_pte_page_dtor/}' $FILE;
done
----
... with the documentation re-flowed to remain under 80 columns, and
whitespace fixed up in macros to keep backslashes aligned.
There should be no functional change as a result of this patch.
Link: http://lkml.kernel.org/r/20190722141133.3116-1-mark.rutland@arm.com
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Yu Zhao <yuzhao@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Document RZ/G2N (R8A774B1) SoC bindings.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
core-api should show all the various string functions including the newly
added stracpy and stracpy_pad.
Miscellanea:
o Update the Returns: value for strscpy
o fix a defect with %NUL)
[joe@perches.com: correct return of -E2BIG descriptions]
Link: http://lkml.kernel.org/r/29f998b4c1a9d69fbeae70500ba0daa4b340c546.1563889130.git.joe@perches.com
Link: http://lkml.kernel.org/r/224a6ebf39955f4107c0c376d66155d970e46733.1563841972.git.joe@perches.com
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Stephen Kitt <steve@sk2.org>
Cc: Nitin Gote <nitin.r.gote@intel.com>
Cc: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Cc: Jann Horn <jannh@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull ceph updates from Ilya Dryomov:
"The highlights are:
- automatic recovery of a blacklisted filesystem session (Zheng Yan).
This is disabled by default and can be enabled by mounting with the
new "recover_session=clean" option.
- serialize buffered reads and O_DIRECT writes (Jeff Layton). Care is
taken to avoid serializing O_DIRECT reads and writes with each
other, this is based on the exclusion scheme from NFS.
- handle large osdmaps better in the face of fragmented memory
(myself)
- don't limit what security.* xattrs can be get or set (Jeff Layton).
We were overly restrictive here, unnecessarily preventing things
like file capability sets stored in security.capability from
working.
- allow copy_file_range() within the same inode and across different
filesystems within the same cluster (Luis Henriques)"
* tag 'ceph-for-5.4-rc1' of git://github.com/ceph/ceph-client: (41 commits)
ceph: call ceph_mdsc_destroy from destroy_fs_client
libceph: use ceph_kvmalloc() for osdmap arrays
libceph: avoid a __vmalloc() deadlock in ceph_kvmalloc()
ceph: allow object copies across different filesystems in the same cluster
ceph: include ceph_debug.h in cache.c
ceph: move static keyword to the front of declarations
rbd: pull rbd_img_request_create() dout out into the callers
ceph: reconnect connection if session hang in opening state
libceph: drop unused con parameter of calc_target()
ceph: use release_pages() directly
rbd: fix response length parameter for encoded strings
ceph: allow arbitrary security.* xattrs
ceph: only set CEPH_I_SEC_INITED if we got a MAC label
ceph: turn ceph_security_invalidate_secctx into static inline
ceph: add buffered/direct exclusionary locking for reads and writes
libceph: handle OSD op ceph_pagelist_append() errors
ceph: don't return a value from void function
ceph: don't freeze during write page faults
ceph: update the mtime when truncating up
ceph: fix indentation in __get_snap_name()
...
|
|
This updates bindings for MT7629 PWM controller.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
- new driver for ICY, an Amiga Zorro card :)
- axxia driver gained slave mode support, NXP driver gained ACPI
- the slave EEPROM backend gained 16 bit address support
- and lots of regular driver updates and reworks
* 'i2c/for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (52 commits)
i2c: tegra: Move suspend handling to NOIRQ phase
i2c: imx: ACPI support for NXP i2c controller
i2c: uniphier(-f): remove all dev_dbg()
i2c: uniphier(-f): use devm_platform_ioremap_resource()
i2c: slave-eeprom: Add comment about address handling
i2c: exynos5: Remove IRQF_ONESHOT
i2c: stm32f7: Make structure stm32f7_i2c_algo constant
i2c: cht-wc: drop check because i2c_unregister_device() is NULL safe
i2c-eeprom_slave: Add support for more eeprom models
i2c: fsi: Add of_put_node() before break
i2c: synquacer: Make synquacer_i2c_ops constant
i2c: hix5hd2: Remove IRQF_ONESHOT
i2c: i801: Use iTCO version 6 in Cannon Lake PCH and beyond
watchdog: iTCO: Add support for Cannon Lake PCH iTCO
i2c: iproc: Make bcm_iproc_i2c_quirks constant
i2c: iproc: Add full name of devicetree node to adapter name
i2c: piix4: Add ACPI support
i2c: piix4: Fix probing of reserved ports on AMD Family 16h Model 30h
i2c: ocores: use request_any_context_irq() to register IRQ handler
i2c: designware: Fix optional reset error handling
...
|
|
Merge updates from Andrew Morton:
- a few hot fixes
- ocfs2 updates
- almost all of -mm (slab-generic, slab, slub, kmemleak, kasan,
cleanups, debug, pagecache, memcg, gup, pagemap, memory-hotplug,
sparsemem, vmalloc, initialization, z3fold, compaction, mempolicy,
oom-kill, hugetlb, migration, thp, mmap, madvise, shmem, zswap,
zsmalloc)
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (132 commits)
mm/zsmalloc.c: fix a -Wunused-function warning
zswap: do not map same object twice
zswap: use movable memory if zpool support allocate movable memory
zpool: add malloc_support_movable to zpool_driver
shmem: fix obsolete comment in shmem_getpage_gfp()
mm/madvise: reduce code duplication in error handling paths
mm: mmap: increase sockets maximum memory size pgoff for 32bits
mm/mmap.c: refine find_vma_prev() with rb_last()
riscv: make mmap allocation top-down by default
mips: use generic mmap top-down layout and brk randomization
mips: replace arch specific way to determine 32bit task with generic version
mips: adjust brk randomization offset to fit generic version
mips: use STACK_TOP when computing mmap base address
mips: properly account for stack randomization and stack guard gap
arm: use generic mmap top-down layout and brk randomization
arm: use STACK_TOP when computing mmap base address
arm: properly account for stack randomization and stack guard gap
arm64, mm: make randomization selected by generic topdown mmap layout
arm64, mm: move generic mmap layout functions to mm
arm64: consider stack randomization for mmap base only when necessary
...
|
|
Cgroup v1 memcg controller has exposed a dedicated kmem limit to users
which turned out to be really a bad idea because there are paths which
cannot shrink the kernel memory usage enough to get below the limit (e.g.
because the accounted memory is not reclaimable). There are cases when
the failure is even not allowed (e.g. __GFP_NOFAIL). This means that the
kmem limit is in excess to the hard limit without any way to shrink and
thus completely useless. OOM killer cannot be invoked to handle the
situation because that would lead to a premature oom killing.
As a result many places might see ENOMEM returning from kmalloc and result
in unexpected errors. E.g. a global OOM killer when there is a lot of
free memory because ENOMEM is translated into VM_FAULT_OOM in #PF path and
therefore pagefault_out_of_memory would result in OOM killer.
Please note that the kernel memory is still accounted to the overall limit
along with the user memory so removing the kmem specific limit should
still allow to contain kernel memory consumption. Unlike the kmem one,
though, it invokes memory reclaim and targeted memcg oom killing if
necessary.
Start the deprecation process by crying to the kernel log. Let's see
whether there are relevant usecases and simply return to EINVAL in the
second stage if nobody complains in few releases.
[akpm@linux-foundation.org: tweak documentation text]
Link: http://lkml.kernel.org/r/20190911151612.GI4023@dhcp22.suse.cz
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Thomas Lindroth <thomas.lindroth@gmail.com>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The debug_pagealloc functionality is useful to catch buggy page allocator
users that cause e.g. use after free or double free. When page
inconsistency is detected, debugging is often simpler by knowing the call
stack of process that last allocated and freed the page. When page_owner
is also enabled, we record the allocation stack trace, but not freeing.
This patch therefore adds recording of freeing process stack trace to page
owner info, if both page_owner and debug_pagealloc are configured and
enabled. With only page_owner enabled, this info is not useful for the
memory leak debugging use case. dump_page() is adjusted to print the
info. An example result of calling __free_pages() twice may look like
this (note the page last free stack trace):
BUG: Bad page state in process bash pfn:13d8f8
page:ffffc31984f63e00 refcount:-1 mapcount:0 mapping:0000000000000000 index:0x0
flags: 0x1affff800000000()
raw: 01affff800000000 dead000000000100 dead000000000122 0000000000000000
raw: 0000000000000000 0000000000000000 ffffffffffffffff 0000000000000000
page dumped because: nonzero _refcount
page_owner tracks the page as freed
page last allocated via order 0, migratetype Unmovable, gfp_mask 0xcc0(GFP_KERNEL)
prep_new_page+0x143/0x150
get_page_from_freelist+0x289/0x380
__alloc_pages_nodemask+0x13c/0x2d0
khugepaged+0x6e/0xc10
kthread+0xf9/0x130
ret_from_fork+0x3a/0x50
page last free stack trace:
free_pcp_prepare+0x134/0x1e0
free_unref_page+0x18/0x90
khugepaged+0x7b/0xc10
kthread+0xf9/0x130
ret_from_fork+0x3a/0x50
Modules linked in:
CPU: 3 PID: 271 Comm: bash Not tainted 5.3.0-rc4-2.g07a1a73-default+ #57
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58-prebuilt.qemu.org 04/01/2014
Call Trace:
dump_stack+0x85/0xc0
bad_page.cold+0xba/0xbf
rmqueue_pcplist.isra.0+0x6c5/0x6d0
rmqueue+0x2d/0x810
get_page_from_freelist+0x191/0x380
__alloc_pages_nodemask+0x13c/0x2d0
__get_free_pages+0xd/0x30
__pud_alloc+0x2c/0x110
copy_page_range+0x4f9/0x630
dup_mmap+0x362/0x480
dup_mm+0x68/0x110
copy_process+0x19e1/0x1b40
_do_fork+0x73/0x310
__x64_sys_clone+0x75/0x80
do_syscall_64+0x6e/0x1e0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x7f10af854a10
...
Link: http://lkml.kernel.org/r/20190820131828.22684-5-vbabka@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently, a value of '1" is written to /sys/kernel/slab/<slab>/shrink
file to shrink the slab by flushing out all the per-cpu slabs and free
slabs in partial lists. This can be useful to squeeze out a bit more
memory under extreme condition as well as making the active object counts
in /proc/slabinfo more accurate.
This usually applies only to the root caches, as the SLUB_MEMCG_SYSFS_ON
option is usually not enabled and "slub_memcg_sysfs=1" not set. Even if
memcg sysfs is turned on, it is too cumbersome and impractical to manage
all those per-memcg sysfs files in a real production system.
So there is no practical way to shrink memcg caches. Fix this by enabling
a proper write to the shrink sysfs file of the root cache to scan all the
available memcg caches and shrink them as well. For a non-root memcg
cache (when SLUB_MEMCG_SYSFS_ON or slub_memcg_sysfs is on), only that
cache will be shrunk when written.
On a 2-socket 64-core 256-thread arm64 system with 64k page after
a parallel kernel build, the the amount of memory occupied by slabs
before shrinking slabs were:
# grep task_struct /proc/slabinfo
task_struct 53137 53192 4288 61 4 : tunables 0 0
0 : slabdata 872 872 0
# grep "^S[lRU]" /proc/meminfo
Slab: 3936832 kB
SReclaimable: 399104 kB
SUnreclaim: 3537728 kB
After shrinking slabs (by echoing "1" to all shrink files):
# grep "^S[lRU]" /proc/meminfo
Slab: 1356288 kB
SReclaimable: 263296 kB
SUnreclaim: 1092992 kB
# grep task_struct /proc/slabinfo
task_struct 2764 6832 4288 61 4 : tunables 0 0
0 : slabdata 112 112 0
Link: http://lkml.kernel.org/r/20190723151445.7385-1-longman@redhat.com
Signed-off-by: Waiman Long <longman@redhat.com>
Acked-by: Roman Gushchin <guro@fb.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Hyper-V direct tlb flush function should be enabled for
guest that only uses Hyper-V hypercall. User space
hypervisor(e.g, Qemu) can disable KVM identification in
CPUID and just exposes Hyper-V identification to make
sure the precondition. Add new KVM capability KVM_CAP_
HYPERV_DIRECT_TLBFLUSH for user space to enable Hyper-V
direct tlb function and this function is default to be
disabled in KVM.
Signed-off-by: Tianyu Lan <Tianyu.Lan@microsoft.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for Merrifield Basin Cove PMIC
New Device Support:
- Add support for Intel Tiger Lake to Intel LPSS PCI
- Add support for Intel Sky Lake to Intel LPSS PCI
- Add support for ST-Ericsson DB8520 to DB8500 PRCMU
New Functionality:
- Add RTC and PWRC support to MT6323
Fix-ups:
- Clean-up include files; davinci_voicecodec, asic3, sm501, mt6397
- Ignore return values from debugfs_create*(); ab3100-*, ab8500-debugfs, aat2870-core
- Device Tree changes; rn5t618, mt6397
- Use new I2C API; tps80031, 88pm860x-core, ab3100-core, bcm590xx,
da9150-core, max14577, max77693, max77843, max8907,
max8925-i2c, max8997, max8998, palmas, twl-core,
- Remove obsolete code; da9063, jz4740-adc
- Simplify semantics; timberdale, htc-i2cpld
- Add 'fall-through' tags; omap-usb-host, db8500-prcmu
- Remove superfluous prints; ab8500-debugfs, db8500-prcmu, fsl-imx25-tsadc,
intel_soc_pmic_bxtwc, qcom_rpm, sm501
- Trivial rename/whitespace/typo fixes; mt6397-core, MAINTAINERS
- Reorganise code structure; mt6397-*
- Improve code consistency; intel-lpss
- Use MODULE_SOFTDEP() helper; intel-lpss
- Use DEFINE_RES_*() helpers; mt6397-core
Bug Fixes:
- Clean-up resources; max77620
- Prevent input events being dropped on resume; intel-lpss-pci
- Prevent sleeping in IRQ context; ezx-pcap"
* tag 'mfd-next-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (48 commits)
mfd: mt6323: Add MT6323 RTC and PWRC
mfd: mt6323: Replace boilerplate resource code with DEFINE_RES_* macros
mfd: mt6397: Add mutex include
dt-bindings: mfd: mediatek: Add MT6323 Power Controller
dt-bindings: mfd: mediatek: Update RTC to include MT6323
dt-bindings: mfd: mediatek: mt6397: Change to relative paths
mfd: db8500-prcmu: Support the higher DB8520 ARMSS
mfd: intel-lpss: Use MODULE_SOFTDEP() instead of implicit request
mfd: htc-i2cpld: Drop check because i2c_unregister_device() is NULL safe
mfd: sm501: Include the GPIO driver header
mfd: intel-lpss: Add Intel Skylake ACPI IDs
mfd: intel-lpss: Consistently use GENMASK()
mfd: Add support for Merrifield Basin Cove PMIC
mfd: ezx-pcap: Replace mutex_lock with spin_lock
mfd: asic3: Include the right header
MAINTAINERS: altera-sysmgr: Fix typo in a filepath
mfd: mt6397: Extract IRQ related code from core driver
mfd: mt6397: Rename macros to something more readable
mfd: Remove dev_err() usage after platform_get_irq()
mfd: db8500-prcmu: Mark expected switch fall-throughs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
"Core Frameworks
- Obtain scale type through sysfs
New Functionality:
- Provide Device Tree functionality in rave-sp-backlight
- Calculate if scale type is (non-)linear in pwm_bl
Fix-ups:
- Simplify code in lm3630a_bl
- Trivial rename/whitespace/typo fixes in lms283gf05
- Remove superfluous NULL check in tosa_lcd
- Fix power state initialisation in gpio_backlight
- List supported file in MAINTAINERS
Bug Fixes:
- Kconfig - default to not building unless requested in
{LED,BACKLIGHT}_CLASS_DEVICE"
* tag 'backlight-next-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: pwm_bl: Set scale type for brightness curves specified in the DT
backlight: pwm_bl: Set scale type for CIE 1931 curves
backlight: Expose brightness curve type through sysfs
MAINTAINERS: Add entry for stable backlight sysfs ABI documentation
backlight: gpio-backlight: Correct initial power state handling
video: backlight: tosa_lcd: drop check because i2c_unregister_device() is NULL safe
video: backlight: Drop default m for {LCD,BACKLIGHT_CLASS_DEVICE}
backlight: lms283gf05: Fix a typo in the description passed to 'devm_gpio_request_one()'
backlight: lm3630a: Switch to use fwnode_property_count_uXX()
backlight: rave-sp: Leave initial state and register with correct device
|
