| Age | Commit message (Collapse) | Author |
|---|
|
The CMA reserved memory nodes have been added for all the IPU and DSP
remoteproc devices in the am572x-idk-common.dtsi file that is common to
both the AM572x and AM574x IDK boards. These nodes are assigned to the
respective rproc device nodes, and all the IPU and DSP remote processors
are enabled.
The current CMA pools and sizes are defined statically for each device.
The addresses chosen are the same as the respective processors on
the AM57xx EVM board to maintain firmware compatibility between the
two boards. The CMA pools and sizes are defined using 64-bit values
to support LPAE. The starting addresses are fixed to meet current
dependencies on the remote processor firmwares, and this will go
away when the remote-side code has been improved to gather this
information runtime during its initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The System Mailboxes 5 and 6 and their corresponding child sub-mailbox
(IPC 3.x) nodes are enabled in each of the DRA7xx and AM57xx board
dts files individually at present. These mailboxes enable the Remote
Processor Messaging (RPMsg) communication stack between the MPU host
processor and each of the IPU1, IPU2, DSP1 and DSP2 remote processors.
Move these nodes into two common dtsi files - dra7-ipu-dsp-common and
dra74-ipu-dsp-common files, which are then included in various board
dts files. These files can be used to add all the common configuration
properties (except memory data) required by remote processor nodes.
The memory pools and the remote processor nodes themselves are to be
enabled in the actual board dts files. The first file is to used by
platforms using DRA72x/DRA71x/AM571x/AM570x SoCs, and the second file
is to be used by platforms using DRA74x/DRA76x/AM572x/AM574x SoCs.
The second file includes the first file and contains additional data
only applicable for DSP2 remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
PERST# line in the PCIE connector is driven by the host mode and not
EP mode. The gpios property here is used for driving the PERST# line.
Remove gpios property from all endpoint device tree nodes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
AM572x-IDK rev 1.3A has tricolor RGB LEDs that can be controlled using
GPIO. Expose these to userspace for usage as necessary.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Dual-role support was added in v4.12. We should be using
it for USB2 port on the am57xx-idk.
Cc: <stable@vger.kernel.org> [4.16+]
Reported-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
am574x-idk is similar to am572x-idk with am574x SoC. So create
a common file for both evms and include SoC dtsi as needed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
