| Age | Commit message (Collapse) | Author |
|---|
|
The usage of the label property for gpio-leds has been deprecated
a long time ago. In bcm2835-rpi.dtsi the ACT LED uses such a label
and derive it to almost every Raspberry Pi board. Since we cannot break
userspace interface this property must be kept. But we can move the
ACT LED into a separate dtsi and include them from the board files.
This change have two benefits:
- with both new refs it's now clear the LED part is included from a dtsi
- new boards do not include the deprecated stuff automatically
Reported-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/20221110173105.6633-3-stefan.wahren@i2se.com
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
The convention to name not connected GPIOs with NC has never been
adapted. Also newer Raspberry Pi boards like RPi 4 never did. So fix
this inconsistency by removing all of the NC names.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
A Wifi/BT chip is quite common for the Raspberry Pi boards. So move those
definitions into a separate dtsi in order to avoid copy & paste. This
change was inspired by a vendor tree patch from Phil Elwell.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1628334401-6577-7-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
|
|
Fix the node names for the GPIO LEDs to conform to the standard node
name led-..
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1622981777-5023-6-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
|
|
This adds the missing properties to the PWR LED for the RPi 3 & 4 boards,
which are already set for the other boards. Without them we will lose
the LED state after suspend.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
There might be headless setups of the Compute Module without HDMI,
so better enable HDMI at board level. Btw this allows moving HDMI
base definition into upcoming bcm2835-common.dtsi.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
|
|
Now with the varity of several RPi boards, the memory should be defined
at board level. This step gives us the chance to fix the memory size
of the RPi 1 B+, Zero (incl. W) and Compute Module 1.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Eric Anholt <eric@anholt.net>
|
|
Compiling the bcm283x DTS with W=1 leads to the following warning:
Warning (unit_address_vs_reg): /memory: node has a reg or ranges property,
but no unit name
Fix this by adding the unit address.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
|
|
The Raspberry Pi 3 A+ is similar to the Pi 3 B+ but has only 512 MB RAM,
1 USB 2.0 port and no Ethernet.
Compared to the Raspberry Pi 3 B it isn't possible to control BT_ON and
WL_ON separately.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
|
