summaryrefslogtreecommitdiff
path: root/arch/arm/boot/dts/bcm47094-linksys-panamera.dts
AgeCommit message (Collapse)Author
2019-07-23ARM: dts: bcm: bcm47094: add missing #cells for mdio-bus-muxArnd Bergmann
The mdio-bus-mux has no #address-cells/#size-cells property, which causes a few dtc warnings: arch/arm/boot/dts/bcm47094-linksys-panamera.dts:129.4-18: Warning (reg_format): /mdio-bus-mux/mdio@200:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) arch/arm/boot/dts/bcm47094-linksys-panamera.dtb: Warning (pci_device_bus_num): Failed prerequisite 'reg_format' arch/arm/boot/dts/bcm47094-linksys-panamera.dtb: Warning (i2c_bus_reg): Failed prerequisite 'reg_format' arch/arm/boot/dts/bcm47094-linksys-panamera.dtb: Warning (spi_bus_reg): Failed prerequisite 'reg_format' arch/arm/boot/dts/bcm47094-linksys-panamera.dts:128.22-132.5: Warning (avoid_default_addr_size): /mdio-bus-mux/mdio@200: Relying on default #address-cells value arch/arm/boot/dts/bcm47094-linksys-panamera.dts:128.22-132.5: Warning (avoid_default_addr_size): /mdio-bus-mux/mdio@200: Relying on default #size-cells value Add the normal cell numbers. Link: https://lore.kernel.org/r/20190722145618.1155492-1-arnd@arndb.de Fixes: 2bebdfcdcd0f ("ARM: dts: BCM5301X: Add support for Linksys EA9500") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Olof Johansson <olof@lixom.net>
2019-06-22ARM: dts: BCM5301X: Fix most DTC W=1 warningsFlorian Fainelli
Fix the bulk of the unit_address_vs_reg warnings and unnecessary \#address-cells/#size-cells without "ranges" or child "reg" property Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2019-01-30ARM: dts: Kill off skeleton{64}.dtsiRob Herring
Remove the usage of skeleton.dtsi in the remaining dts files. It was deprecated since commit 9c0da3cc61f1 ("ARM: dts: explicitly mark skeleton.dtsi as deprecated"). This will make adding a unit-address to memory nodes easier. The main tricky part to removing skeleton.dtsi is we could end up with no /memory node at all when a bootloader depends on one being present. I hacked up dtc to check for this condition. Acked-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Acked-by: Antoine Tenart <antoine.tenart@bootlin.com> Acked-by: Alexandre TORGUE <alexandre.torgue@st.com> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> Acked-by: Vladimir Zapolskiy <vz@mleia.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Rob Herring <robh@kernel.org> Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com> Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2018-07-09ARM: dts: BCM5301X: Add support for Linksys EA9500Vivek Unune
Hardware Info ------------- Processor - Broadcom BCM4709C0KFEBG dual-core @ 1.4 GHz Switch - BCM53012 in BCM4709C0KFEBG & external BCM53125 DDR3 RAM - 256 MB Flash - 128 MB (Toshiba TC58BVG0S3HTA00) 2.4GHz - BCM4366 4×4 2.4/5G single chip 802.11ac SoC Power Amp - Skyworks SE2623L 2.4 GHz power amp (x4) 5GHz x 2 - BCM4366 4×4 2.4/5G single chip 802.11ac SoC Power Amp - PLX Technology PEX8603 3-lane, 3-port PCIe switch Ports - 8 Ports, 1 WAN Ports Antennas - 8 Antennas Serial Port - @J6 [GND,TX,RX] (VCC NC) 115200 8n1 Tested with OpenWrt built with DSA driver and Kernel v4.14 Signed-off-by: Vivek Unune <npcomplete13@gmail.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2018-07-09ARM: dts: BCM5301X: Make USB 3.0 PHY use MDIO PHY driverVivek Unune
Currently, the USB 3.0 PHY in bcm5301x.dtsi uses platform driver which requires register range "ccb-mii" <0x18003000 0x1000>. This range overlaps with MDIO cmd and param registers (<0x18003000 0x8>). Essentially, the platform driver partly acts like a MDIO bus driver, hence to use of this register range. In some Northstar devices like Linksys EA9500, secondary switch is connected via external MDIO. The only way to access and configure the external switch is via MDIO bus. When we enable the MDIO bus in it's current state, the MDIO bus and any child buses fail to register because of the register range overlap. On Northstar, the USB 3.0 PHY is connected at address 0x10 on the internal MDIO bus. This change moves the usb3_phy node and makes it a child node of internal MDIO bus. Thanks to Rafał Miłecki's commit af850e14a7ae ("phy: bcm-ns-usb3: add MDIO driver using proper bus layer") the same USB 3.0 platform driver can now act as USB 3.0 PHY MDIO driver. Tested on Linksys Panamera (EA9500) Signed-off-by: Vivek Unune <npcomplete13@gmail.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2018-05-03ARM: dts: BCM5301X: Relicense most DTS files to the GPL 2.0+ / MITRafał Miłecki
These files were created and ever touched by a group of three people only: Dan, Hauke and me. They were licensed under GNU/GPL or ISC. Introducing and discussing SPDX-License-Identifier resulted in a conclusion that ISC is a not recommended license (see also a license-rules.rst). Moveover an old e-mail from Alan Cox was pointed which explained that dual licensing is a safer solution than depending on a common compatibility belief. This commit switches most of BCM5301X DTS files to dual licensing using: 1) GPL 2.0+ to make sure they are compatible with Linux kernel 2) MIT to allow sharing with more permissive projects Both licenses belong to the preferred ones (see LICENSES/preferred/). An attempt to relicense remaining files will be made separately and will require approve from more/other developers. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Dan Haab <dan.haab@luxul.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2017-03-05ARM: dts: BCM5301X: Add basic DT for Linksys EA9500Rafał Miłecki
It's tri-band wireless home router based on BCM47094 AKA BCM4709C0. It uses 3 x BCM4366 chipsets for wireless. Panamera seems to be board name used by Linksys. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>