| Age | Commit message (Collapse) | Author |
|---|
|
The Nomadik GPIO controller now relies on Nomadik pinctrl, however
the pinctrl driver is not currently started by any ux500 platform.
This is requred or GPIOs do not work at all.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Here we supply the information required to setup regulators successfully
on Snowball and other db8500 variants which use the ab8500 regulators.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Here we inform Device Tree of which regulators are provided by the db8500-
prcmu. This way we can reference some of their consumers directly from the
Device Tree e.g. SMSC911x Ethernet chip.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This patch applies the correct format requested by the irq
domain. For chained IRQs which use GPIO lines as IRQs, we
stipulate that a two cell request is required. The first cell
contains the requested IRQ and the second can contain flags
pertaining to edge detection and level sensitive values. The
zeroth cell specifies the GPIO controller by use of a phandle.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Apply db8500 related PRCMU Device Tree settings and clean up some formatting
errors. We also remove one of the PRCMU assigned IRQs, as it is currently not
used.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This patch adds the information required for successful
registration of the PRCMU timer 4 (clocksource) driver to the
db8500 Device Tree include file.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Here we split the description of the external-bus@50000000 over
two description files. In the more generic db8500 description file
we only specify the external-bus. Normally this would be used to
communicate with a NOR-flash device. On the Snowball however, the
SMSC9115 Ethernet chip occupies it. In the Snowball board specific
description file is where we actually specify that it is in fact the
Ethernet device which lives here.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This creates Device Tree bindings for the Nomadik GPIO driver.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Split off from the patch actually implementing the bindings]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
It is believed that the gpio compatible match entry is too long
and cumbersome in its current form. This patch takes steps to
decrease its length by using ST-Microelectronics' abbreviation ST.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
It is believed that the i2c compatible match entry is too long
and cumbersome in its current form. This patch takes steps to
decrease its length by using ST-Microelectronics' abbreviation ST.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
These were incorrectly introduced and can cause problems for of_irq_init.
The correct way to define a root controller is no interrupt-parent set at
all or the interrupt-parent is set to the root controller itself when
inherited from a parent node.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Tested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This enables local timer (AKA: private timer) support for
all u8500 based hardware using DT.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This SSP Controller supports a number of serial communication methods
and as such cannot be registered using of_register_spi_devices.
Instead we register it simply as a primecell device.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This provides PL310 Level 2 Cache Controller Device Tree
support for all u8500 based devices.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This enables the embedded GIC on all u8500 based hardware using DT.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This adds all devices that are normally present through the
u8500_init_machine function in the device tree as well, which
will duplicate the devices that are visible.
This will not do much by itself because the device from the
device tree are not matched by any device driver until they
are converted as well. The next step is to move over one
device at a time to actually be used from the device tree
instead of the hardcoded device using auxdata to pass the
correct platform_data.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
db8500.dtsi can be used by all systems with a db8500 or
db9500 SoC, while snowball.dts is board specific.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
