| Age | Commit message (Collapse) | Author |
|---|
|
Add nodes for GPU (Mali 400) to Exynos4210 and Exynos4412. Describe the
GPU as much as possible however still few elements are missing:
1. Exynos4210 bus clock is not described in hardware manual therefore
the IP gate clock was provided,
2. Exynos4412: Not sure what to do with CLK_G3D clock responsible for
gating entire IP block (it is now being disabled as unused),
3. Regulator supplies on Trats board.
Limited testing on Odroid U3 (Exynos4412).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Commit 225da7e65a03 ("ARM: dts: add eMMC reset line for
exynos4412-odroid-common") added MMC power sequence for eMMC card of
Odroid X2/U3. It reused generic sd1_cd pin control configuration node
and only disabled pull-up. However that time the pinctrl configuration
was not applied during MMC power sequence driver initialization. This
has been changed later by commit d97a1e5d7cd2 ("mmc: pwrseq: convert to
proper platform device").
It turned out then, that the provided pinctrl configuration is not
correct, because the eMMC_RTSN line is being re-configured as 'special
function/card detect function for mmc1 controller' not the simple
'output', thus the power sequence driver doesn't really set the pin
value. This in effect broke the reboot of Odroid X2/U3 boards. Fix this
by providing separate node with eMMC_RTSN pin configuration.
Cc: <stable@vger.kernel.org>
Reported-by: Markus Reichl <m.reichl@fivetechno.de>
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes: 225da7e65a03 ("ARM: dts: add eMMC reset line for exynos4412-odroid-common")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
LDO20 regulator provides power for the MMC card on Odroid U3 boards. That
regulator has been marked as 'boot-on' since the beginning of Odroid X/U3
support, but such flag is not really needed for it. That regulator is
correctly described as supply for eMMC card and controlled by its driver.
Commit 05f224ca6693 ("regulator: core: Clean enabling always-on regulators
+ their supplies") changed the way the boot-on regulators are handled and
since then regulators marked as 'boot-on' got increased reference count
and are not turned off for the system suspend time.
The new approach turned out to break suspend/resume support on Odroid U3
with eMMC card, because the card is not properly shutdown due to missing
of power cycle. Fix this by removing excessive 'boot-on' flag and let
MMC driver to control turning power on and off.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The SDHCI standard, MMC host controller bindings and MMC core defines
card detect pin as active low. Therefore there is no point to invert it
twice.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
This patch switches Odroid X/X2/U3 to use dedicated Odroid audio subsystem
DT bindings instead of the simple-card in order to add support for audio
over HDMI.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Extend camera node by label, not by full path in Exynos 4412 Odroid
boards. This avoids error-prone redefinition of nodes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Replace GPL v2.0 license statements with SPDX license identifiers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/soc
Pull "Samsung DTS ARM changes for 4.15" from Krzysztof Kozłowski:
1. Add new board: Hardkernel Odroid HC1.
2. Fix incomplete Odroid-XU3/4 thermal-zones definition leading to
possible overheat if first pair of A7+A15 cores is idle but rest of
CPUs are busy.
3. Add capacity-dmips-mhz properties for CPUs of octa-core SoCs.
4. Add power button to Odroid XU3/4.
5. Improvements in Gscaler, HDMI and Mixer blocks on Exynos5.
6. Add suspend quirk to DWC3 USB controller to fix enumeration of
SuperSpeed devices on Odroid XU4.
7. Add HDMI and MHL to Trats2.
8. Cleanups (redundant properties and nodes).
* tag 'samsung-dt-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
dt-bindings: samsung: Document binding for new Odroid HC1 board
ARM: dts: exynos: Add HDMI and Sil9234 to Trats2 board
ARM: dts: exynos: Add support for Hardkernel's Odroid HC1 board
ARM: dts: exynos: Move audio clocks configuration to odroidxu3-audio.dtsi
ARM: dts: exynos: Add dwc3 SUSPHY quirk
ARM: dts: exynos: Add status property to Exynos 542x Mixer nodes
ARM: dts: exynos: Add status property to Exynos 5250 HDMI and Mixer nodes
ARM: dts: exynos: Cleanup HDMI DCC definitions on Exynos5250 and Exynos542x boards
ARM: dts: exynos: Move HDMI PHY node from boards to exynos5250.dtsi
ARM: dts: exynos: Use specific compatibles for proper Gscaler limits on Exynos5250 and Exynos5420
ARM: dts: exynos: Remove redundant interrupt properties in gpio-keys on Odroid boards
ARM: dts: exynos: Add power button for Odroid XU3/4
ARM: dts: exynos: Remove the display-timing and delay from Rinato
ARM: dts: exynos: add exynos5422 cpu capacity-dmips-mhz information
ARM: dts: exynos: add exynos5420 cpu capacity-dmips-mhz information
ARM: dts: exynos: fix incomplete Odroid-XU3/4 thermal-zones definition
|
|
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm/boot/dts -type -f -name '*.dts*'
Dropped changes to ARM, Ltd. boards LED nodes and manually fixed up some
occurrences of uppercase hex.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Odroid boards
GPIO keys don't need interrupt property. Interrupt number can be derived
directly from the GPIO pin definition, so remove redundant 'interrupts'
and 'interrupt-parent' properties from gpio-keys nodes on
Exynos4412-based Odroid boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
dwmmc driver deprecated num-slots and plan to get rid
of it finally. Just move a step to cleanup it from DT.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
sources
Replace hard-coded values of interrupt flags with respective macros from
header to increase code readability.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Watchdog module does not have external dependencies so it can be safely
enabled in exynos4.dtsi thus making it available for all Exynos4-based
boards.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add CPU operating points for Exynos4412 Prime (it supports
additional 1704MHz & 1600MHz OPPs and 1500MHz OPP is just
a regular non-turbo OPP on this SoC). Also update relevant
cooling maps to account for new OPPs.
ODROID-X2/U2/U3 boards use Exynos4412 Prime SoC version so
update their board files accordingly.
Based on Hardkernel's kernel for ODROID-X2/U2/U3 boards.
Cc: Doug Anderson <dianders@chromium.org>
Cc: Andreas Faerber <afaerber@suse.de>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Cc: Ben Gamari <ben@smart-cactus.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Move assigned clocks properties from sound node to audio subsystem clock
controller node. This way clocks topology and rates are set just after
probing audio clocks controller. Leaving those properties under
sound node doesn't guarantee to configure them before they are being used
(for example i2s hardware module can be probed in parallel and it also
require proper audio clocks configuration).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
"iis", "i2s_opclk0" and "i2s_opclk1" are standard clocks for Exynos4 I2S
hardware module, so they should be defined in .dtsi file not in the random
board .dts file.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Pull "Topic branch for Samsung DeviceTree cleanup for 4.9" from Krzysztof Kozłowski:
Replace in DT sources hard-coded values for pinctrl configuration like pull
up/down, drive strength and function. This makes the DTS easier to read,
especially that some drive strengths values are quite non-obvious.
* tag 'samsung-dt-pinctrl-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: s3c64xx: Use macros for pinctrl configuration
ARM: dts: s3c2416: Use macros for pinctrl configuration
ARM: dts: s5pv210: Use macros for pinctrl configuration
ARM: dts: s3c64xx: Use common macros for pinctrl configuration
ARM: dts: exynos: Fix mismatched values of SD drive strengh configuration on exynos4415
ARM: dts: exynos: Fix mismatched value for SD4 pull up/down configuration on exynos4210
ARM: dts: exynos: Use macros for pinctrl configuration on exynos542x/exynos5800
ARM: dts: exynos: Use macros for pinctrl configuration on exynos5410
ARM: dts: exynos: Use macros for pinctrl configuration on exynos5260
ARM: dts: exynos: Use macros for pinctrl configuration on exynos5250
ARM: dts: exynos: Use macros for pinctrl configuration on exynos4415
ARM: dts: exynos: Use macros for pinctrl configuration on exynos4x12
ARM: dts: exynos: Use macros for pinctrl configuration on exynos4210
ARM: dts: exynos: Use macros for pinctrl configuration on exynos3250
ARM: dts: exynos: Use common macros for pinctrl configuration
pinctrl: dt-bindings: samsung: Update documentation with new macros
pinctrl: dt-bindings: samsung: Add header with values used for configuration
|
|
Usage of DTS macros instead of hard-coded numbers makes code easier to
read. One does not have to remember which value means pull-up/down or
specific driver strength.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch enables getting a HPD GPIO descriptor quicker.
The exynos-hdmi driver uses "hpd" for HDMI hot plug detection.
static int hdmi_resources_init(struct hdmi_context *hdata)
{
...
hdata->hpd_gpio = devm_gpiod_get(dev, "hpd", GPIOD_IN);
...
}
This calls 'of_find_gpio()' and it generates the GPIO consumer ID by referring
GPIO suffix. So 'hpd-gpios' is preferred on getting a GPIO descriptor.
However, if the device tree uses 'hpd-gpio', then the exynos-hdmi driver
always retries to get a GPIO descriptor because the first GPIO suffix is not
'gpio' but 'gpios'. So you always see the debug message below.
of_get_named_gpiod_flags: can't parse 'hpd-gpios' property of node '/soc/hdmi@14530000[0]'
Use the preferred property, 'hpd-gpios' instead of 'hpd-gpio'.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Topic branch for Exynos MFC changes for v4.8, part 2:
Replace hardcoded reserved memory ranges with auto-allocated ones
and enable MFC for all boards.
* tag 'samsung-drivers-exynos-mfc-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: enable MFC device for all boards
ARM: dts: exynos: move MFC reserved memory regions from boards to .dtsi
ARM: dts: exynos: replace hardcoded reserved memory ranges with auto-allocated ones
ARM: dts: exynos: Enable MFC device on Exynos4412 Odroid boards
ARM: dts: exynos: Convert MFC device to generic reserved memory bindings
ARM: EXYNOS: Remove code for MFC custom reserved memory handling
media: s5p-mfc: add iommu support
media: s5p-mfc: replace custom reserved memory handling code with generic one
media: s5p-mfc: use generic reserved memory bindings
of: reserved_mem: add support for using more than one region for given device
media: set proper max seg size for devices on Exynos SoCs
media: vb2-dma-contig: add helper for setting dma max seg size
s5p-mfc: Fix race between s5p_mfc_probe() and s5p_mfc_open()
s5p-mfc: Add release callback for memory region devs
s5p-mfc: Set device name for reserved memory region devs
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
MFC device can be used without any external hardware dependencies (when
IOMMU is enabled), so it can be enabled by default (like it has been
already done for Exynos 542x platforms). This unifies handling of this
device for Exynos3250, Exynos4 and Exynos542x platforms. Board can still
include exynos-mfc-reserved-memory.dtsi to enable using this device
without IOMMU being enabled.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
This patch moves assigning reserved memory regions from each board dts
to common exynos-mfc-reserved-memory.dtsi file, where those regions are
defined.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
Enable support for Multimedia Codec (MFC) device for all Exynos4412-based
Odroid boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
Odroid X/X2/U3 schematics say that SD card vmmc regulator
(LDO21/TFLASH) operates on 2.8 V. Mainline U-Boot uses that value as
well and 2.8 V is common on Exynos-based boards. Additionally use some
descriptive name for this regulator.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
|
|
The eMMC card vmmc-supply contained incorrectly two regulators: LDO20
and buck8. The second one is ignored. Additionally the buck8 is a vqmmc
supply only on X and X2. On U3 the buck8 is providing power to the LAN
(SMSC95xx) so instead the LDO22 should be used.
Fix this by defining proper vmmc and vqmmc supplies for respective
boards.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
|
|
Odroid X/X2/U3
The SD-card vmmc-supply contained incorrectly two regulators. The second
one is ignored. Fix this by defining proper vmmc and vqmmc supplies.
Additionally these regulators do not have to be always on, so allow
disabling them to reduce energy consumption.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late DT updates from Arnd Bergmann:
"This is a collection of a few late fixes and other misc stuff that had
dependencies on things being merged from other trees.
The Renesas R-Car power domain handling, and the Nvidia Tegra USB
support both hand notable changes that required changing the DT
binding in a way that only provides compatibility with old DT blobs on
new kernels but not vice versa. As a consequence, the DT changes are
based on top of the driver changes and are now in this branch.
For NXP i.MX and Samsung Exynos, the changes in here depend on other
changes that got merged through the clk maintainer tree"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (35 commits)
ARM: dts: exynos: Add support of Bus frequency using VDD_INT for exynos5422-odroidxu3
ARM: dts: exynos: Add bus nodes using VDD_INT for Exynos542x SoC
ARM: dts: exynos: Add NoC Probe dt node for Exynos542x SoC
ARM: dts: exynos: Add support of bus frequency for exynos4412-trats/odroidu3
ARM: dts: exynos: Expand the voltage range of buck1/3 regulator for exynos4412-odroidu3
ARM: dts: exynos: Add support of bus frequency using VDD_INT for exynos3250-rinato
ARM: dts: exynos: Add exynos4412-ppmu-common dtsi to delete duplicate PPMU nodes
ARM: dts: exynos: Add bus nodes using VDD_MIF for Exynos4210
ARM: dts: exynos: Add bus nodes using VDD_INT for Exynos4x12
ARM: dts: exynos: Add bus nodes using VDD_MIF for Exynos4x12
ARM: dts: exynos: Add bus nodes using VDD_INT for Exynos3250
ARM: dts: exynos: Add DMC bus frequency for exynos3250-rinato/monk
ARM: dts: exynos: Add DMC bus node for Exynos3250
ARM: tegra: Enable XUSB on Nyan
ARM: tegra: Enable XUSB on Jetson TK1
ARM: tegra: Enable XUSB on Venice2
ARM: tegra: Add Tegra124 XUSB controller
ARM: tegra: Move Tegra124 to the new XUSB pad controller binding
ARM: dts: r8a7794: Use SYSC "always-on" PM Domain
ARM: dts: r8a7793: Use SYSC "always-on" PM Domain
...
|
|
This patch adds the bus device tree nodes for both MIF (Memory) and INT
(Internal) block to enable the bus frequency.
The DMC bus is parent device in MIF block using VDD_MIF and the LEFTBUS
bus is parent device in INT block using VDD_INT.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[m.reichl and linux.amoon: Tested it on exynos4412-odroidu3 board]
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
exynos4412-odroidu3
This patch expands the voltage range of buck1/3 regulator due to as following:
- MIF (Memory Interface) bus frequency needs the range of '900 - 1100 mV'.
- INT (Internal) bus frequency needs the range of '900 - 1050 mV'.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[m.reichl and linux.amoon: Tested it on exynos4412-odroidu3 board]
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
This patch adds the exynos4412-ppmu-common.dtsi to remove duplicate PPMU nodes
because exynos3250-rinato/monk, exynos4412-trats2/odroidu3 has the same
PPMU device tree node.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[m.reichl and linux.amoon: Tested it on exynos4412-odroidu3 board]
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
There is no external dependency for Security SubSystem (SSS) block so
the nodes for Pseudo Random Number Generator and AES hardware
acceleration can be enabled always for all Exynos4 devices.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
Add a dts node entry and enable the HDMI CEC device present in the Exynos4
family of SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[k.kozlowski: Put the node in alphabetical order]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
Enable the Security SubSystem (SSS) on Exynos4412-based Odroid boards
to provide hardware acceleration for AES operations.
Suggested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
|
|
Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "linux-keypad,wakeup" boolean property to enable the
wakeup source, "wakeup-source" is the new standard binding.
This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any further copy-paste
duplication.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
G2D device is always available and doesn't depend on any external (board
specific) peripherals, so it can be unconditionally enabled.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
The board DTS are using numeric values instead of the defined GPIO
constanst to express polarity, use them to make the DTS more clear.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Use 'ldoN_reg: LDON' syntax and drop the deprecated
'regulator-compatible' property.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
The pinctrl settings in i2c_0 and i2c_1 are already provided
through the exynos4 dtsi.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
For Exynos4x12 platforms, add CPU operating points (using
opp-v2 bindings) and CPU regulator supply properties for
migrating from Exynos specific cpufreq driver to using
generic cpufreq driver.
Based on the earlier work by Thomas Abraham.
Cc: Doug Anderson <dianders@chromium.org>
Cc: Andreas Faerber <afaerber@suse.de>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
For thermal zones:
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
The Exynos4412 SoC has a s3c6410 RTC where the source clock
is now a mandatory property.
This patch fixes probe failure of s3c-rtc on Odroid-X2/U2/U3 boards.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung DT updates for v4.1" from Kukjin Kim:
- for exynos3250
: add assigned clock parents for CMU nodes
- for exynos4412-odroid
: add eMMC reset line
- for exynos5250
: fixed typo for interrupt-cells
- for exynos5250-snow
: define stdout-path property
: represent bridge and panel connection
: enable wifi power-on and add cap-sdio-irq to wifi mmc node
- for exynos5250-spring
: define stdout-path property
- for exynos5420
: fixed typo for interrupt-cells
: add async-bridge clocks for gsc and disp1 PDs
- for exynos5420 boards
: Mux XMMCnDATA[0] pad correctly
- for exynos5420-odroidxu3
: add eMMC reset line
- for Peach boards
: add HS400 support and define stdout-path property
: add mclk entry and add WiFi module support
: represent bridge and panel connection
* tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Fixed typo interrupt-cells for exynos5420 and exynos5250
ARM: dts: Add HS400 support for exynos5420 and exynos5800
ARM: dts: add async-bridge clocks to gsc power domain for exynos5420
ARM: dts: add async-bridge clocks to disp1 power domain for exynos5420
dt-bindings: add asynchronous bridge clock for exynos
ARM: dts: Define stdout-path property for exynos5250-spring
ARM: dts: Define stdout-path property for exynos5250-snow
ARM: dts: Define stdout-path property for Peach boards
ARM: dts: Add assigned clock parents to CMU node for exynos3250
ARM: dts: Add mclk entry for Peach boards
ARM: dts: Add WiFi module support for Peach boards
ARM: dts: Mux XMMCnDATA[0] pad correctly for Exynos5420 boards
ARM: dts: add eMMC reset line for exynos5422-odroidxu3
ARM: dts: add eMMC reset line for exynos4412-odroid-common
ARM: dts: represent bridge and panel connection for exynos5420-peach-pit
ARM: dts: represent bridge and panel connection for exynos5250-snow
ARM: dts: Add cap-sdio-irq to wifi mmc node for exynos5250-snow
ARM: dts: Enable wifi power-on for exynos5250-snow
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This patch adds nodes specific to Exynos4412 based Odroid X/X2/U2/U3
boards required for enabling HDMI display.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Presented patch aims to move data necessary for correct CPU cooling device
configuration from exynos_tmu_data.c to device tree.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
This commit enables TMU IP block on the Exynos4412 Odroid based
devices such as Odroid U3.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
This patch adds LDO10 regulator node for TMU.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
This patch adds reset-gpios property to the eMMC slot, so the MMC driver
is able to properly reset eMMC card on system restart and thus fixes
system hang on software reboot.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"DT changes continue to be the bulk of our merge window contents.
We continue to have a large set of changes across the board as new
platforms and drivers are added.
Some of the new platforms are:
- Alphascale ASM9260
- Marvell Armada 388
- CSR Atlas7
- TI Davinci DM816x
- Hisilicon HiP01
- ST STiH418
There have also been some sweeping changes, including relicensing of
DTS contents from GPL to GPLv2+/X11 so that the same files can be
reused in other non-GPL projects more easily. There's also been
changes to the DT Makefile to make it a little less conflict-ridden
and churny down the road"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (330 commits)
ARM: dts: Add PPMU node for exynos4412-trats2
ARM: dts: Add PPMU node for exynos3250-monk and exynos3250-rinato
ARM: dts: Add PPMU dt node for exynos4 and exynos4210
ARM: dts: Add PPMU dt node for exynos3250
ARM: dts: add mipi dsi device node for exynos4415
ARM: dts: add fimd device node for exynos4415
ARM: dts: Add syscon phandle to the video-phy node for Exynos4
ARM: dts: Add sound nodes for exynos4412-trats2
ARM: dts: Fix CLK_MOUT_CAMn parent clocks assignment for exynos4412-trats2
ARM: dts: Fix CLK_UART_ISP_SCLK clock assignment in exynos4x12.dtsi
ARM: dts: Add max77693 charger node for exynos4412-trats2
ARM: dts: Switch max77686 regulators to GPIO control for exynos4412-trats2
ARM: dts: Add suspend configuration for max77686 regulators for exynos4412-trats2
ARM: dts: Add Maxim 77693 fuel gauge node for exynos4412-trats2
ARM: dts: am57xx-beagle-x15: Fix USB2 mode
ARM: dts: am57xx-beagle-x15: Add extcon nodes for USB
ARM: dts: dra72-evm: Add extcon nodes for USB
ARM: dts: dra7-evm: Add extcon nodes for USB
ARM: dts: rockchip: move the hdmi ddc-i2c-bus property to the actual boards
ARM: dts: rockchip: enable vops and hdmi output on rk3288-firefly and -evb
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver patches from Greg KH:
"Here's the big tty/serial driver update for 3.20-rc1. Nothing huge
here, just lots of driver updates and some core tty layer fixes as
well. All have been in linux-next with no reported issues"
* tag 'tty-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (119 commits)
serial: 8250: Fix UART_BUG_TXEN workaround
serial: driver for ETRAX FS UART
tty: remove unused variable sprop
serial: of-serial: fetch line number from DT
serial: samsung: earlycon support depends on CONFIG_SERIAL_SAMSUNG_CONSOLE
tty/serial: serial8250_set_divisor() can be static
tty/serial: Add Spreadtrum sc9836-uart driver support
Documentation: DT: Add bindings for Spreadtrum SoC Platform
serial: samsung: remove redundant interrupt enabling
tty: Remove external interface for tty_set_termios()
serial: omap: Fix RTS handling
serial: 8250_omap: Use UPSTAT_AUTORTS for RTS handling
serial: core: Rework hw-assisted flow control support
tty/serial: 8250_early: Add support for PXA UARTs
tty/serial: of_serial: add support for PXA/MMP uarts
tty/serial: of_serial: add DT alias ID handling
serial: 8250: Prevent concurrent updates to shadow registers
serial: 8250: Use canary to restart console after suspend
serial: 8250: Refactor XR17V35X divisor calculation
serial: 8250: Refactor divisor programming
...
|
