| Age | Commit message (Collapse) | Author |
|---|
|
The DH electronics PDK2 can be populated with SoM with i.MX6S/DL/D/Q
variants. Split the SoC-independent parts of the SoM and PDK2 into the
imx6qdl-dhcom-*.dtsi and reduce imx6q-dhcom-pdk2.dts to example of
adding i.MX6S/DL/D/Q variants of the SoM into a PDK2 carrier board.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Following cleanups of the devicetrees done, no change in function:
- Remove parentheses from the license
- Update copyright date
- Alphabetical sorting
- Add comments
- Update pinctrl names
- Hex values in lower case
- Set 3rd values of fixed regulators gpio property to 0
- Replace interrupt type with a define
- Remove superfluous property max-speed from the fec node
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Move iomux to the end, no change in function.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The function of each SoM pins is defined in the DHCOM standard [1] and
subset of them is defined as GPIOs (pins A-W). To ensure the interchange-
ability of the DHCOM SoMs, the function of the pins are fixed and cannot
be changed. On board level the DHCOM GPIOs can be used associated with
different blocks e.g. for interrupt or reset, but the function is always
GPIO. If not used, they can be freely used in the user space.
Therefore the whole configuration of SoM pins is made in the SoM DT.
Defining the DHCOM GPIO pins as a separate pinctrl nodes makes moving a
subset of them to an appropriate block pinctrl group easier on board level,
since it is not necessary to have a large pinctrl hog group containing
unrelated pinmux entries on board level. This also makes it easy to update
the SoM DT without having to update all the board DTs too. If necessary it
is also possible to change the electrical properties of the DHCOM GPIOs by
overwriting the pinctrl on board level.
[1] https://wiki.dh-electronics.com/images/2/2e/DOC_DHCOM-Standard-Specification_R01_2016-11-17.pdf
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The minimum available memory size of all DHCOM i.MX6 variants is 512 MB.
Set this value for the memory node. If U-Boot fails to fill the memory
size, at least all DHCOM i.MX6 variants should run without problems.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The pin CSI0_DATA_EN is reserved for PCIe Wake. Move this pin to
the SoM devicetree. Add PCIe Reset GPIO to the board devicetree.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fill in the custom GPIO line names used by DH on the DHCOM SoM.
The GPIO line names are in accordance to DHCOM Design Guide R04
available at [1], section 3.9 GPIO. Adding also GPIO line names
for the hardware and memory coding.
[1] https://wiki.dh-electronics.com/images/5/52/DOC_DHCOM-Design-Guide_R04_2018-06-28.pdf
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable the interrupt mode for the ethernet PHY by adding the
necessary property and a separate pinctrl for the PHY. Also
add the compatible property for it.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the parallel system bus provided by the i.MX6 WEIM interface via an
address latch. The OE pin of the latch is controlled by a fixed regulator.
The pin is low active. This is ensured by omitting the regulators property
enable-active-high. The flags value of the gpio property (3rd value), which
is also use to define active high/low, is set to 0 because it is ignored
by gpiolib-of.c.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Pull ARM devicetree updates from Olof Johansson:
"Like always, the DT branch is sizable. There are numerous additions
and fixes to existing platforms, but also a handful of new ones
introduced. Less than some other releases, but there's been
significant work on cleanups, refactorings and device enabling on
existing platforms.
A non-exhaustive list of new material:
- Refactoring of BCM2711 dtsi structure to add support for the
Raspberry Pi 400
- Rockchip: RK3568 SoC and EVB, video codecs for
rk3036/3066/3188/322x
- Qualcomm: SA8155p Automotive platform (SM8150 derivative),
SM8150/8250 enhancements and support for Sony Xperia 1/1II and
5/5II
- TI K3: PCI/USB3 support on AM64-sk boards, R5 remoteproc
definitions
- TI OMAP: Various cleanups
- Tegra: Audio support for Jetson Xavier NX, SMMU support on Tegra194
- Qualcomm: lots of additions for peripherals across several SoCs,
and new support for Microsoft Surface Duo (SM8150-based), Huawei
Ascend G7.
- i.MX: Numerous additions of features across SoCs and boards.
- Allwinner: More device bindings for V3s, Forlinx OKA40i-C and
NanoPi R1S H5 boards
- MediaTek: More device bindings for mt8167, new Chromebook system
variants for mt8183
- Renesas: RZ/G2L SoC and EVK added
- Amlogic: BananaPi BPI-M5 board added"
* tag 'arm-dt-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (511 commits)
arm64: dts: rockchip: add basic dts for RK3568 EVB
arm64: dts: rockchip: add core dtsi for RK3568 SoC
arm64: dts: rockchip: add generic pinconfig settings used by most Rockchip socs
ARM: dts: rockchip: add vpu and vdec node for RK322x
ARM: dts: rockchip: add vpu nodes for RK3066 and RK3188
ARM: dts: rockchip: add vpu node for RK3036
arm64: dts: ipq8074: Add QUP6 I2C node
arm64: dts: rockchip: Re-add regulator-always-on for vcc_sdio for rk3399-roc-pc
arm64: dts: rockchip: Re-add regulator-boot-on, regulator-always-on for vdd_gpu on rk3399-roc-pc
arm64: dts: rockchip: add ir-receiver for rk3399-roc-pc
arm64: dts: rockchip: Add USB-C port details for rk3399 Firefly
arm64: dts: rockchip: Sort rk3399 firefly pinmux entries
arm64: dts: rockchip: add infrared receiver node to RK3399 Firefly
arm64: dts: rockchip: add SPDIF node for rk3399-firefly
arm64: dts: rockchip: Add Rotation Property for OGA Panel
arm64: dts: qcom: sc7180: bus votes for eMMC and SD card
arm64: dts: qcom: sm8250-edo: Add Samsung touchscreen
arm64: dts: qcom: sm8250-edo: Enable GPI DMA
arm64: dts: qcom: sm8250-edo: Enable ADSP/CDSP/SLPI
arm64: dts: qcom: sm8250-edo: Enable PCIe
...
|
|
Add VIO regulator that supplies multiple ethernet magnetics and
currently there is no upstream support for that in the networking,
so just keep the regulator enabled always to emulate what other
boards, which have this hard-wired, do. Until there is support.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add aliases for i2c and serial to match the order of the DHCOM
standard [1]. Also add aliases for the two rtcs. The i2c rtc
is the primary one.
[1] https://wiki.dh-electronics.com/images/2/2e/DOC_DHCOM-Standard-Specification_R01_2016-11-17.pdf
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The i2c bus can freeze at the end of transaction so the bus can no longer work.
This scenario is improved by adding scl/sda gpios definitions to implement the
i2c bus recovery mechanism.
Fixes: 52c7a088badd ("ARM: dts: imx6q: Add support for the DHCOM iMX6 SoM and PDK2")
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
To make the ethernet cable plugin detection reliable the
power detection of the smsc phy has been disabled.
Fixes: 52c7a088badd ("ARM: dts: imx6q: Add support for the DHCOM iMX6 SoM and PDK2")
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix ethernet reset time properties as described in
Documentation/devicetree/bindings/net/ethernet-phy.yaml
Fixes: 52c7a088badd ("ARM: dts: imx6q: Add support for the DHCOM iMX6 SoM and PDK2")
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Per schematic, both PU and SOC regulator are supplied from LTC3676 SW1
via VDDSOC_IN rail, add the PU input. Both VDD1P1, VDD2P5 are supplied
from LTC3676 SW2 via VDDHIGH_IN rail, add both inputs.
While no instability or problems are currently observed, the regulators
should be fully described in DT and that description should fully match
the hardware, else this might lead to unforseen issues later. Fix this.
Fixes: 52c7a088badd ("ARM: dts: imx6q: Add support for the DHCOM iMX6 SoM and PDK2")
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: stable@vger.kernel.org
Reviewed-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The conversion of the spi-imx driver to use GPIO descriptors
in commit 8cdcd8aeee28 ("spi: imx/fsl-lpspi: Convert to GPIO descriptors")
helped to detect the following SPI chipselect polarity mismatch on an
imx6q-sabresd:
[ 4.854337] m25p80@0 enforce active low on chipselect handle
Prior to the above commit, the chipselect polarity passed via cs-gpios
property was ignored and considered active-low.
The reason for such mismatch is clearly explained in the comments inside
drivers/gpio/gpiolib-of.c:
* SPI children have active low chip selects
* by default. This can be specified negatively
* by just omitting "spi-cs-high" in the
* device node, or actively by tagging on
* GPIO_ACTIVE_LOW as flag in the device
* tree. If the line is simultaneously
* tagged as active low in the device tree
* and has the "spi-cs-high" set, we get a
* conflict and the "spi-cs-high" flag will
* take precedence.
To properly represent the SPI chipselect polarity, change it to active-low
when the "spi-cs-high" property is absent.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The only correct and documented compatible string for the rv3029 is
microcrystal,rv3029. Fix it up.
Fixes: 52c7a088badd ("ARM: dts: imx6q: Add support for the DHCOM iMX6 SoM and PDK2")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Move the CAN enablement from SoM DTSi to board DTS, as each board might need
different CAN configuration. Moreover, disable CAN2 on the PDK2 as it is not
available on any connector. This also fixes on-SoM SD slot operation, as it
shares pins with the CAN2.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Boards based on imx6qdl have duplicate memory nodes:
- One coming from the board device tree file: memory@
- One coming from the imx6qdl.dtsi file.
Fix the duplication by removing the memory node from
the imx6qdl.dtsi file and by adding 'device_type = "memory";'
in the board Device Tree.
Converted using the following command:
perl -p0777i -e 's/memory\@10000000 \{\n/memory\@10000000 \{\n\t\tdevice_type = \"memory\";\n/m' `find ./arch/arm/boot/dts -name "imx6*"``
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for the DH i.MX6 Quad based SoM and a PDK2 evaluation board.
The evaluation board features three serial ports, USB OTG, USB host with
an USB hub, Fast or Gigabit ethernet, eMMC, uSD, SD, mSATA, analog audio,
PCIe and HDMI video output.
All of the aforementioned features are supported by this patch.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
