| Age | Commit message (Collapse) | Author |
|---|
|
The SoM itself provides the display interface, see [1] page 20.
Those pins have to be used as the RGB/DPI interface or not used
at all. So rather than duplicate the pinmux settings in every
carrier board DT, better move them into the SoM DTSI.
[1] https://wiki.dh-electronics.com/images/2/2e/DOC_DHCOM-Standard-Specification_R01_2016-11-17.pdf
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add USB overcurrent pin muxing on SoM layer. On DRC02 and PDK2 the USB
overcurrent pin isn't connected, but a USB hub on the board takes care
of the USB overcurrent instead. Therefore disable it there with the
property disable-over-current.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Identify the PHY by its compatible ID value. In some cases during
boot, the PHY needs to be reset to be accessible, but this is only
possible if the PHY is recognized. In that case, the automatic
detection of the PHY does not work and a static compatible ID
value is need.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
According to datasheet Microchip LAN8710A/LAN8710Ai DS00002164B [1]
the reset should stay asserted for at least 100uS and software
should wait at least 200nS. On other DHCOM SoMs with the SMSC
LAN8710Ai PHY both reset delays are 500us. This should be plenty
and for consistency, the i.MX6 SoM should also use these delays.
[1] https://ww1.microchip.com/downloads/en/DeviceDoc/00002164B.pdf
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The DH electronics PDK2 can be populated with SoM with i.MX6S/DL/D/Q
variants. Split the SoC-independent parts of the SoM and PDK2 into the
imx6qdl-dhcom-*.dtsi and reduce imx6q-dhcom-pdk2.dts to example of
adding i.MX6S/DL/D/Q variants of the SoM into a PDK2 carrier board.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
