| Age | Commit message (Collapse) | Author |
|---|
|
Remove the unnecessary #address-cells/#size-cells to avoid warnings
from W=1 build like this:
arch/arm/boot/dts/imx6qdl-gw52xx.dtsi:33.12-78.4: Warning (avoid_unnecessary_addr_size): /gpio-keys: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
[fabio: Make the warning messages more succint]
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 = IRQ_TYPE_EDGE_RISING
Correct the interrupt flags, assuming the author of the code wanted same
logical behavior behind the name "ACTIVE_xxx", this is:
ACTIVE_LOW => IRQ_TYPE_LEVEL_LOW
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The conversion of the spi-imx driver to use GPIO descriptors
in commit 8cdcd8aeee28 ("spi: imx/fsl-lpspi: Convert to GPIO descriptors")
helped to detect the following SPI chipselect polarity mismatch on an
imx6q-sabresd:
[ 4.854337] m25p80@0 enforce active low on chipselect handle
Prior to the above commit, the chipselect polarity passed via cs-gpios
property was ignored and considered active-low.
The reason for such mismatch is clearly explained in the comments inside
drivers/gpio/gpiolib-of.c:
* SPI children have active low chip selects
* by default. This can be specified negatively
* by just omitting "spi-cs-high" in the
* device node, or actively by tagging on
* GPIO_ACTIVE_LOW as flag in the device
* tree. If the line is simultaneously
* tagged as active low in the device tree
* and has the "spi-cs-high" set, we get a
* conflict and the "spi-cs-high" flag will
* take precedence.
To properly represent the SPI chipselect polarity, change it to active-low
when the "spi-cs-high" property is absent.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add Gateworks System Controller support to Gateworks Ventana boards:
- add dt bindings for GSC mfd driver and hwmon driver for ADC's and
fan controllers.
- add dt bindings for gpio-keys driver for push-button and interrupt events
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Connect the wl_reg regulator to usdhc2 such that it can be enabled
and disabled as needed. There is no need for this to be always-on.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Sterling-LWB has a BCM4330 which has a UART based bluetooth
HCI. Add support for binding to the bcm_hci driver to take care
of handling the shutdown gpio and loading firmware.
Because the shutdown gpio is more of an enable than a regulator
go ahead and replace the regulator with a shutdown-gpio.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The GW5910-C revision adds a TI CC1352 connected to IMX UART4
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Gateworks GW5910 is an IMX6 SoC based single board computer with:
- IMX6Q or IMX6DL
- 32bit DDR3 DRAM
- FEC GbE RJ45 front-panel
- 1x miniPCIe socket with PCI Gen2, USB2
- 1x miniPCIe socket with PCI Gen2, USB2, nanoSIM
- 5V to 60V DC input barrel jack
- 3axis accelerometer (lis2de12)
- GPS (ublox ZOE-M8Q)
- bi-color front-panel LED
- 256MB NAND boot device
- microSD socket (with UHS-I support)
- user pushbutton
- Gateworks System Controller (hwmon, pushbutton controller, EEPROM)
- Dual-Band Wireless MCU (CC1352, UART/I2S interrconnect to IMX6)
- WiFi/Bluetooth/BLE module (Sterling-LSW, SDIO/UART interconnect to IMX6)
- RS232 transceiver (1x UART with flow-control or 2x UART (build option)
- off-board SPI connector (1x chip-select)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Robert Jones <rjones@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
