| Age | Commit message (Collapse) | Author |
|---|
|
commit 200a575b68d2 ("ARM: dts: meson: organize devices in their corresponding busses")
organized all peripherals in busses so that the base register offset of
the bus doesn't have to be included in all child-nodes anymore.
The GPIO interrupt controller however specifies the register offset
without subtracting the "cbus" base address. This leads to a problem
where of_iomap inside the irq-meson-gpio driver fails because it
actually tries to map 0x182209880 (cbus base = 0xc1100000 + 0xc1109880
for the GPIO interrupt controller). Fix this by using 0x9880 as register
offset.
Fixes: 7d32bc03bcfb ("ARM: dts: meson8b: enable gpio interrupt controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Nodes are sorted by their register start address. Move gpio_intc to the
correct position.
No functional changes intended.
Fixes: 7d32bc03bcfb ("ARM: dts: meson8b: enable gpio interrupt controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Meson6, Meson8 and Meson8b use a similar IP block which has access to
512 bytes of efuse data.
During SoC manufacturing some calibration settings for the CVBS
connector and the internal temperature sensor are written to this efuse.
On some boards it additionally stores for example the MAC addresses.
The efuse is enabled on Meson8 and Meson8b but kept disabled on Meson6
since we do not have a clock driver there (which is required to read
data from the efuse).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add gpio interrupt controller node to the meson8b boards
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Meson6, Meson8 and Meson8b are using the same MMC controller IP. This
adds the MMC controller node to meson.dtsi so it can be used by all
SoCs.
The controller itself is a bit special, because it has multiple slots.
Each slot is accessed through a sub-node of the controller. However,
currently the driver for this hardware only supports one slot.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The SoC type and version information is encoded in different register
blocks.
The SoC type information is part of the "assist" registers.
The misc version information is part of the "bootrom" registers.
On Meson8, Meson8b and Meson8m2 there is additionally information about
the minor version. This information is stored in the "analog top"
registers.
Add the nodes for these register blocks so we can decode the SoC type
and version information.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This patch fixes the Meson6, Meson8 and Meson8b USB controllers dts nodes
which interrupts are level type instead of edge type.
This avoids errors like "usb 1-1-port1: cannot reset (err = -110)" and
similars on Odroid-C1+ board.
Fixes: e29b1cf87473 ("ARM: dts: meson: add USB support on Meson8 and Meson8b")
Signed-off-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The UART bindings needs specifying a SoC family, use the meson6 family
for the UART nodes like the other nodes.
Switch to the stable UART bindings for meson6 by adding a XTAL node and
using the proper compatible strings.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
All 32bit Meson SoCs contain 128KiB SRAM. This SRAM is used when
suspending the device (the the ARM Power Firmware on
Meson8/Meson8b/Meson8m2 saves the DDR settings there) and to boot the
secondary CPU cores.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
According to the vendor kernel sources these also exist (at the same
address) on Meson6 and Meson8. This can be found by running
$ grep -R "define PWM_PWM_[A-D]" arch/arm/
in the Amlogic GPL kernel tree (arm-src-kernel-2015-01-15-321cfb5a46).
pwm_ef does not seem to exist on older SoCs, so we keep it in
meson8b.dtsi for now.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This adds the DWC2 USB controller nodes and the corresponding USB2 PHY
nodes to meson.dtsi (as the same - or at least a very similar) IP block
is used on all SoCs (at the same physical address).
Additionally meson8.dtsi and meson8b.dtsi add the required clocks to the
DWC2 and USB2 PHY nodes, otherwise the DWC2 controller cannot be
initialized by the dwc2 driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
All supported Meson SoCs have a random number generator in CBUS.
Newer SoCs (GXBB, GXL and GXM) provide only one 32-bit random number
register, whereas the older SoCs (Meson6, Meson8 and Meson8b) have two
32-bit random number registers. The existing meson-rng driver only
supports the lower 32-bit - but it still works fine on the older SoCs
apart from this small limitation.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This adds the SAR ADC to meson.dtsi and configures the clocks on Meson8
and Meson8b to allow boards to use it. Some boards use it to connect a
button to it.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This makes meson.dtsi easier to read as we are not using magic numbers
for the GIC interrupt type (GIC_SPI) and the interrupt polarity
(IRQ_TYPE_EDGE_RISING).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The Amlogic Meson SoCs have most of the internal peripherals organized
in busses. Use them to make the dts easier to read and to avoid
duplicated register (bus) offset definitions.
The bus information is taken from the vendor kernel:
#define IO_CBUS_PHY_BASE 0xc1100000 ///2M
#define IO_AOBUS_PHY_BASE 0xc8100000 ///1M
There are more internal busses (such as the abp bus which seems to
contain audio, HDMI and Mali registers), but since we don't have
drivers for them yet these are not added (yet).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[khilman: minor whitespace fix]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The DTS erronously uses the wrong reg mapping and IRQ numbers for some
UART, WDT and timer nodes. Fix this.
Reported-by: John Wehle <john@feith.com>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add a node for the Ethernet controller to Meson DTS file and
enable it on the Geniatech ATV1200 board.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
|
|
This adds a node for the SPI Flash Controller to the Amlogic Meson
DTS.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Two new dvb frontend drivers: mn88472 and mn88473
- A new driver for some PCIe DVBSky cards
- A new remote controller driver: meson-ir
- One LIRC staging driver got rewritten and promoted to mainstream:
igorplugusb
- A new tuner driver (m88rs6000t)
- The old omap2 media driver got removed from staging. This driver
uses an old DMA API and it is likely broken on recent kernels.
Nobody cared enough to fix it
- Media bus format moved to a separate header, as DRM will also use the
definitions there
- mem2mem_testdev were renamed to vim2m, in order to use the same
naming convention taken by the other virtual test driver (vivid)
- Added a new driver for coda SoC (coda-jpeg)
- The cx88 driver got converted to use videobuf2 core
- Make DMABUF export buffer to work with DMA Scatter/Gather and Vmalloc
cores
- Lots of other fixes, improvements and cleanups on the drivers.
* tag 'media/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (384 commits)
[media] mn88473: One function call less in mn88473_init() after error
[media] mn88473: Remove uneeded check before release_firmware()
[media] lirc_zilog: Deletion of unnecessary checks before vfree()
[media] MAINTAINERS: Add myself as img-ir maintainer
[media] img-ir: Don't set driver's module owner
[media] img-ir: Depend on METAG or MIPS or COMPILE_TEST
[media] img-ir/hw: Drop [un]register_decoder declarations
[media] img-ir/hw: Fix potential deadlock stopping timer
[media] img-ir/hw: Always read data to clear buffer
[media] redrat3: ensure dma is setup properly
[media] ddbridge: remove unneeded check before dvb_unregister_device()
[media] si2157: One function call less in si2157_init() after error
[media] tuners: remove uneeded checks before release_firmware()
[media] arm: omap2: rx51-peripherals: fix build warning
[media] stv090x: add an extra protetion against buffer overflow
[media] stv090x: Remove an unreachable code
[media] stv090x: Some whitespace cleanups
[media] em28xx: checkpatch cleanup: whitespaces/new lines cleanups
[media] si2168: add support for firmware files in new format
[media] si2168: debug printout for firmware version
...
|
|
This adds a node for the IR remote control receiver to the Amlogic
Meson DTS.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Add nodes for I2C controllers A,B,AO, which are available in both
Meson6 and Meson8.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Carlo Caione <carlo@caione.org>
|
|
This enables the L2 cache controller available in Amlogic SoCs.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Carlo Caione <carlo@caione.org>
|
|
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Carlo Caione <carlo@caione.org>
|
|
The Meson6 SoC is produced by Amlogic inc. and it is based on 2 Cortex
A9 and an ARM Mali-400 GPU.
This patch adds two basic DTSI for the preliminary support of Meson and
Meson6 SoCs. Another DTS is also added for supporting the atv1200 board,
produced by Geniatech inc.
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
