| Age | Commit message (Collapse) | Author |
|---|
|
The firmware leaves the pins in GPIO mode. Until we have a proper pinmux
driver hooked on we just need to bitbang SPI. No big deal, this is just
used for the power button and performance is not important.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lore.kernel.org/r/20210121034130.1381872-12-lkundrak@v3.sk'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This adds support for the power button attached to the Embedded Controller
on a Dell Wyse 3020 "Ariel" board.
However, while the EC itself is controlled via I2C, the input capability
for the power button acts as a separate device attached to the SPI, hence
it has a separate device node.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lore.kernel.org/r/20210121034130.1381872-11-lkundrak@v3.sk'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add the device node for the computer's embedded controller, responsible
for controlling the LEDs and system power.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lore.kernel.org/r/20210121034130.1381872-10-lkundrak@v3.sk'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Drop the linux,usable-memory properties; the schema is unhappy about
them.
They've been cargo-culted from Open Firmware and I don't know what
purpose they serve. Perhaps they are meant to provide the OFW runtime.
In that case it's still okay to drop them from here; OFW is welcome to add
it upon boot.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lore.kernel.org/r/20210121034130.1381872-6-lkundrak@v3.sk'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Enable the 2D (GC300) and the 3D (GC2000) GPUs cores.
Link: https://lore.kernel.org/r/20200718205019.184927-14-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
I've managed to get about everything wrong while digging these out of
OEM's board file.
Correct the bus numbers, the exact model of the NOR flash, polarity of
the chip selects and align the SPI frequency with the data sheet.
Tested that it works now, with a slight fix to the PXA SSP driver.
Link: https://lore.kernel.org/r/20200419171157.672999-16-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
There's a SMSC USB2640 (USB hub & SD controller) connected to it, but
the SD card slot footprint is unpopulated. Also connected to the hub is
a SMSC LAN7500 gigabit ethernet adapter.
Link: https://lore.kernel.org/r/20191220065314.237624-6-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Make sure UART3, where the console is, is called ttyS2. That is
consistent with the early console.
Link: https://lore.kernel.org/r/20191031163455.1711872-5-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Ponted out by DTC:
<stdout>: Warning (unit_address_vs_reg): /memory: node has a reg or ranges
property, but no unit name
Link: https://lore.kernel.org/r/20191031163455.1711872-4-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This is a Dell Wyse thin client, variously referred to as "Ariel",
"3020" or "Tx0D" where "x" stands for the software it was shipped with.
I somewhat arbitrarily chose "ariel".
There are bits missing, because the drivers are not in and bindings are not
settled yet:
* Things missing from mmp3.dtsi:
HSIC controller and its PHY (only the internal Ethernet is connected
here, the hub with external USB2 ports is connected to the U2O controller
that works well), Vivante GC2000 GPU
* &twsi1/regulator@19
Marvell 88pm867 power regulator
* &twsi3/vga-dvi-encoder@76
Chrontel CH7033B-BF VGA & DVI encoder
* &twsi3/sound-codec@30
Sound chip, probably a Marvell 88ce156
* &twsi4/embedded-controller@58
ENE KB3930QF Embedded Controller, also seems to be connected to &ssp4.
Might not need a driver -- about the only useful thing it can do is to
reboot the machine when tickled via some GPIO lines.
Also there seems to be something at &twsi1 address 0x50.
Link: https://lore.kernel.org/r/20191022152837.3553524-1-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
