| Age | Commit message (Collapse) | Author |
|---|
|
The clock polarity setting of the mcbsp connected to
the modem was wrong so almost only noise
was received.
With this patch it is also the same as it was on
earlier non-dt kernels where it was working properly
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This helps to get 100% intensity closer to "always on".
It compensates for an effect of dmtimer which at 100% still emits short
"off" impulses and the startup-time of the DC/DC converter makes
backlight intensity not reach full scale. The lower the PWM frequency
is, the smaller is this effect.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch fixes the following DTC warnings for omap3-gta04a3.dtb,
omap3-gta04a4.dtb and omap3-gta04a5.dtb:
"dmtimer-pwm@11 has a unit name, but no reg property"
"connector@1 has a unit name, but no reg property"
"endpoint@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Define RFID eeprom node which is present on gta04
device.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Without that change wifi card isn't probed because pwrseq is necessary for
libertas chip.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Define pinmux and usage if irq pin.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Define pinmux and usage if irq pin + fix irq edge.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add pinmux and usage of bma180 irq pin.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Define pwm backlight node which is using dmtimer pwm.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add compatible id, GPMC register resource and interrupt
resource to NAND controller nodes.
The GPMC node will provide an interrupt controller for the
NAND IRQs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "linux,wakeup" boolean property to enable the wakeup
source, "wakeup-source" is the new standard binding.
This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Many OMAP2+ DTS are not using the defined constants to express
the GPIO polarity. Replace these so the DTS are easier to read.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add voice audio card which is used for telephony on gta04 board.
gtm601 codec is UMTS modem with pcm interface which get samples from
microphone and provide data from other party side. Use simple audio card
to describe audio card.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Enable omap-hdq for battery fuel gauge access.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
ti,codec property is not used (parsed) in omap-twl4030 driver. The ti,twl4030-audio
which ti,codec points by phandle is mfd driver and device for ASoC codec is created
w/o DT compatible string. Removing all references in DT files.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The twl4030 keypad is not wired up in the gta04, so mark it disabled
to avoid pointless initialization.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
i.e. configure vpll2 as a supply for the dss rather
than being always-on.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add comments to state which GPIO is used for some interrupts.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Enabled poweroff through PMIC on GTA04.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
GPIO_115 used as irq is in &gpio4, not &gpio3.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
mcbsp2 is used in gta04 soundcard config and by default
is disabled so enable it for gta04.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Audio should be child of twl node.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix attribute names.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add handling for gta04 tv out chain:
venc -> opa362 -> svideo
Use invert-polarity in venc node because opa362
is doing polarity inversion also.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Use omap specific pinctrl defines (OMAP3_CORE1_IOPAD) to configure
the padconf register offset.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The GPMC binding is obviously very confusing as the values
are all over the place. People seem to confuse the GPMC partition
size for the chip select, and the device IO size within the GPMC
partition easily.
The ranges entry contains the GPMC partition size. And the
reg entry contains the size of the IO registers of the
device connected to the GPMC.
Let's fix the issue according to the following table:
Device GPMC partition size Device IO size
connected in the ranges entry in the reg entry
NAND 0x01000000 (16MB) 4
16550 0x01000000 (16MB) 8
smc91x 0x01000000 (16MB) 0xf
smc911x 0x01000000 (16MB) 0xff
OneNAND 0x01000000 (16MB) 0x20000 (128KB)
16MB NOR 0x01000000 (16MB) 0x01000000 (16MB)
32MB NOR 0x02000000 (32MB) 0x02000000 (32MB)
64MB NOR 0x04000000 (64MB) 0x04000000 (64MB)
128MB NOR 0x08000000 (128MB) 0x08000000 (128MB)
256MB NOR 0x10000000 (256MB) 0x10000000 (256MB)
Let's also add comments to the fixed entries while at it.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch is preparation of adding more boards which have common moved
to omap3-gta04.dtsi. Other boards have only small additions to omap3-gta04a4.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
