| Age | Commit message (Collapse) | Author |
|---|
|
Add compatible values to Ethernet PHY subnodes representing Realtek
RTL8201FL PHYs on RZ/A2 boards. This allows software to identify the
PHY model at any time, regardless of the state of the PHY reset line.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/a23eca16869457684b0300379233e335b4e2047e.1631174218.git.geert+renesas@glider.be
|
|
Enable the third I2C channel, and describe the I2C EEPROM connected to
it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/786f0354fb30b183d5bccb2f12b13e6535b9ace1.1626267234.git.geert+renesas@glider.be
|
|
As upstream Linux does not support XIP (eXecute-In-Place) for ARMv7-A
platforms that are part of the ARCH_MULTIPLATFORM framework, it cannot
run in the 8 MiB of HyperRAM present on the RZ/A2M CPU board. Hence the
64 MiB of SDRAM on the sub-board needs to be enabled, which has the
following ramifications:
- SCIF4 connected to the on-board USB-serial can no longer be used as
the serial console,
- Instead, SCIF2 is used as the serial console, by connecting a 3.3V
TTL USB-to-Serial adapter to the CMOS camera connector,
- The first Ethernet channel can no longer be used,
- USB Channel 1 loses the overcurrent input signal.
Based on the Linux-4.19 BSP for RZ/A2.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Chris Brandt <chris.brandt@renesas.com>
Link: https://lore.kernel.org/r/20210304094945.4003097-1-geert+renesas@glider.be
|
|
Add support for input switch SW3 on the Renesas RZ/A2M EVB
development board.
Note that this uses the IRQ interrupt, as the RZ/A2 GPIO controller
does not include interrupt support
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch sorts the nodes of arch/arm/boot/dts/r7s9210-rza2mevb.dts.
* Sort subnodes of root ("/") node alphabetically
* Sort following top-level nodes alphabetically
* Sort subnodes of pinctrl alphabetically
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
[simon: rebase and sort new ehci nodes]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Enable USB Host support for both the Type-C connector on the CPU board
and the Type-A plug on the sub board.
Both boards are also capable of USB Device operation as well after the
appropriate Device Tree modifications.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The RZ/A2M EVB has a 48MHz clock attached to USB_X1.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add ethernet aliases so u-boot can find the device nodes.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The RZ/A2M EVB supports 2 SD card slots. A micro SD slot on the CPU
board, and a full SD card slot on the sub board.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The RZ/A2M EVB sub board has 2 Ethernet jacks on it.
Set switch SW6_4 to ON to use Ethernet Ch-0
Set switch SW6_5 to ON to use Ethernet Ch-1
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add support for Renesas RZ/A2M evaluation board.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
