| Age | Commit message (Collapse) | Author |
|---|
|
This force-converts the per-device battery node into the standard
properties using "simple-battery" for the HREF machines and the
corresponding Samsung battery for the mobile phones.
This is fine to do since the battery data in the DTS files has never
been deployed or used. In commit a1149ae97554
"ARM: ux500: Disable Power Supply and Battery Management by default"
it was turned off and has not been switched back on since. In
the meantime standardized bindings for batteries have appeared
making the old AB8500 battery bindings obsolete.
The battery node which is now in the middle of an included file
is obviously a per-device piece of information so push this down
to each board. The HREF machines all have the same battery and can
share a single node in the HREF dtsi file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fix all the remaining dtc 'unit_address_format' warnings except for the ones
related to 'register-bit-led'. For those, we need to decide on and document
the node name.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210823165126.2320910-1-robh@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
At the moment the AB8500 USB PHY driver still uses the old USB PHY
subsystem instead of the generic PHY subsystem. This means that there
is no explicit link between the USB controller and the USB PHY.
In U-Boot the PHY driver is integrated in the generic PHY subsystem,
so we need to use the typical PHY device tree bindings to specify
which PHY belongs to the USB controller.
Add the link between USB controller and PHY to both ste-ab8500.dtsi
and ste-ab8505.dtsi. This is mainly for U-Boot for now and will just
be ignored in Linux. However, if the AB8500 USB PHY driver in Linux
is moved to the generic PHY subsystem at some point these device tree
changes can be used as well.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Rename the AB8500 gpio controller node from ab8500-gpio to
ab8500-gpiocontroller, since -gpio is a common suffix for
gpio consumers.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fix interrupt cells in DT AB8500/AB8505 source files. The
compiled DTB files will stay the same.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The voltage default on the AB8500 VAUX1 regulator is way
too low and does not correspond to the setting in the
vendor tree. This should be 2.8-3.3 V not 2.5-2.9 V or
things like the HREFP520 touchscreen will not work.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The different charger nodes in the AB8500 and AB8505
includes was missing the interrupt assignments for the
interrupts necessary to drive the AB8500/AB8505 charging
state machine.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The AB8500/AB8505 is providing ADC channels and do so
using the standard property "io-channel-names" not the
mistakenly singular form "io-channel-name".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Rename the DSI controller nodes from "dsi-controller@"
to "dsi@" so they match the naming convention in the
YAML schema for DSI controllers.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201104133758.1373298-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
As per 'struct mfd_cell ab8500_devs[]' there are not 1, but 3 PWM
devices on the AB8500. Until now, each of them have referenced
the same Device Tree node. This change ensures each device has
their own.
Due to recent `dtc` checks [0], nodes cannot share the same node
name, so we are forced to rename the affected nodes by appending
their associated numeric 'bank ID'.
[0] ste-ab8500.dtsi:210.16-214.7: ERROR (duplicate_node_names):
/soc/prcmu@80157000/ab8500/ab8500-pwm: Duplicate node name
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200622083432.1491715-1-lee.jones@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
I renamed the dsi-nodes from dsi@ to dsi-controller@
so that the schema check would kick in, but missed to
rename it in a few places.
Link: https://lore.kernel.org/r/20200326222536.86441-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This adds the IIO channels for the GPADC after converting it
to using the standard IIO ADC bindings and moving the driver
over to the IIO subsystem. We also add IIO hwmon standard
driver node to support reading channels in a standard manner.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Support for the USB regulator of AB8500 was removed in
commit 41a06aa738ad ("regulator: ab8500: Remove USB regulator").
However, the configuration was never removed from the device tree.
It does no longer have any effect, remove it from the device tree.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Some Ux500 devices use the newer AB8505 PMIC instead of AB8500.
Although they are very similar, there are subtle differences
like the number of regulators or the available GPIO pins.
At the moment, ste-dbx5x0.dtsi always configures the AB8500 PMIC.
To support devices with AB8505, it is necessary to split the
AB8500-specific parts into a separate .dtsi file. Boards can then
select the PMIC by including either ste-ab8500.dtsi or ste-ab8505.dtsi.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
