| Age | Commit message (Collapse) | Author |
|---|
|
Add a fixed regulator and use it as power supply for DSI panel.
Fixes: 18c8866266 ("ARM: dts: stm32: Add display support on stm32f469-disco")
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Remove dma-ranges from ltdc node since it is already set
on bus node.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
DT validation ("make dtbs_check") has shown that some memory nodes were not
correctly written. This commit fixes this kind of issue:
"stm32f746-disco.dt.yaml: /: memory: False schema does not allow
{'device_type': ['memory'], 'reg': [[3221225472, 8388608]]}"
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Remove the usage of skeleton.dtsi in the remaining dts files. It was
deprecated since commit 9c0da3cc61f1 ("ARM: dts: explicitly mark
skeleton.dtsi as deprecated"). This will make adding a unit-address to
memory nodes easier.
The main tricky part to removing skeleton.dtsi is we could end up with
no /memory node at all when a bootloader depends on one being present. I
hacked up dtc to check for this condition.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Remove cd-inverted property and update cd-gpios active level
accordingly
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Add display support on the stm32f469-disco board.
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Use gpio bindings for vcc5v_otg.
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Add node for user push button.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Add nodes for the four user leds.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch adds SDIO-related DT nodes required by stm32f469 board
There is a hardware issue on these boards, it misses a pullup on
the GPIO line used as card detect to allow correct SD card
detection. To allow correct card detection "broken-cd" property
is used.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Currently, same stm32f429-pinctrl driver is used for stm32f429 and
stm32f469. As pin map is different between those 2 MCUs,
a stm32f469-pinctrl driver has been recently added.
This patch
-allows to use stm32f469-pinctrl driver for stm32f469 boards
-reworks stm32 devicetree files to fit with stm32f429 / stm32f469
In the same time it fixes an issue when only MACH_STM32F469 flag is
selected in menuconfig.
Fixes: d28bcd53fa90 ("ARM: stm32: Introduce MACH_STM32F469 flag")
Reported-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
The rootfs is independent from the board.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
This patch enables USB FS on stm32f469-disco with 5V VBUS enable.
Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
Define and enable pwm1 and pwm3 for stm32f469 discovery board
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
This patch enables RTC on stm32f469-disco with default LSE clock source.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
This patch adds USART3 pin configuration on PB10/PA11 pins
for STM32F469I-DISCO board.
Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
This patch fix memory size to support 16MB of external SDRAM.
Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
This patch adds the QSPI clock for stm32f469 discovery board.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
stm32f469-disco and stm32f429-eval boards use SDRAM start address remapping
(to @0) to boost performances. A DMA translation through "dma-ranges"
property was needed for other masters than the M4 CPU.
stm32f429-disco doesn't use remapping so doesn't need this DMA translation.
This patches moves this DMA translation definition from stm32f429 soc file
to board files.
Tested-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
It's pretty similar to the STM32F429, but there are some
subtle changes required to boot successfully.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
|
