| Age | Commit message (Collapse) | Author |
|---|
|
Add support of Cirrus cs42l51 audio codec on stm32mp157a-dk1 board.
Configuration overview:
- SAI2A is the CPU interface used for the codec audio playback
- SAI2B is the CPU interface used for the codec audio record
- SAI2A is configured as a clock provider for the audio codec
- SAI2A&B are configured as slave of the audio codec
- SAI2A&B share the same interface of the audio codec
Note:
In master mode, cs42l51 audio codec provides a bitclock
at 64 x FS, regardless of data width. This means that
slot width is always 32 bits.
Set slot width to 32 bits and slot number to 2
in SAI2A&B endpoint nodes, to match this constraint.
dai-tdm-slot-num and dai-tdm-slot-width properties are used here,
assuming that i2s is a special case of tdm, where slot number is 2.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Enable m4 coprocessor for STM32MP157a-dk1 board.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Declare reserved memories shared by the processors for STM32MP157a-dk1
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
On disco and eval board, Tx and Rx delay are applied (pull-up of 4.7k
put on VDD) so which correspond to RGMII-ID mode with internal RX and TX
delays provided by the PHY, the MAC should not add the RX or TX delays
in this case
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Enable hdmi bridge sii9022 & display controller.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Append I2C 1 for stm32mp157c-dk1.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Enable Vivante GPU driver for stm32mp157a-dk1 and dk2 boards.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Four packages exist for stm32mp157 die. As ball-out is different between
them, this patch covers those differences by creating dedicated pinctrl
dtsi files. Each dtsi pinctrl package file describes the package ball-out
through gpio-ranges.
stm32mp157a-dk1 / dk2 boards embed a STM32MP_PKG_AC (TFBGA361 (12*12))
package.
stm32mp157c-ed1 / ev1 boards embed a STM32MP_PKG_AA (LFBGA448 (18*18))
package.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Enable CEC (Consumer Electronics Control) device.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch adds stpmic1 support on stm32mp157a dk1 board.
The STPMIC1 is a PMIC from STMicroelectronics. The STPMIC1 integrates 10
regulators, 3 power switches, a watchdog and an input for a power on key.
The DMAs are disabled because the PMIC generates a very few traffic and
DMA channels may lack for other usage.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Enable STM32 IPCC mailbox driver for STM32MP157a-dk1 board.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch adds sdmmc1 support on stm32mp157a dk1 board.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Add support of stm32mp157a discovery1 board (part number: STM32MP157A-DK1).
This board embeds a STM32MP157a SOC with AC package (TFBGA361, 148 ios)
and 512MB of DDR3. Several connections are available on this boards:
4*USB2.0, 1*USB2.0 typeC, SDcard, RJ45, HDMI, Arduino connector, ...
This patch enables basic support for a kernel boot.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
