| Age | Commit message (Collapse) | Author |
|---|
|
The LAN8710 Energy Detect Power Down (EDPD) functionality might cause
unreliable cable detection. There are multiple accounts of this in the
SMSC PHY driver patches which attempted to make EDPD reliable, however
it seems there is always some sort of corner case left. Unfortunatelly,
there is no errata documented which would confirm this to be a silicon
bug on the LAN87xx series of PHYs (LAN8700, LAN8710, LAN8720 at least).
Disable EDPD on the DHCOM SoM, just like multiple other boards already
do as well, to make the cable detection reliable.
Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The DHCOM SoM has two RTC, one is the STM32 RTC built into the SoC
and another is Microcrystal RV RTC. By default, only the later has
battery backup, the former does not. The order in which the RTCs
are probed on boot is random, which means the kernel might pick up
system time from the STM32 RTC which has no battery backup. This
then leads to incorrect initial system time setup, even though the
HW RTC has correct time configured in it.
Add DT alias entries, so that the RTCs get assigned fixed IDs and
the HW RTC is always picked by the kernel as the default RTC, thus
resulting in correct system time in early userspace.
Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
On some STM32 MP15 boards, stpmic node is not correct which generates
warnings running "make dtbs_check W=1" command. Issues are:
-"regulator-active-discharge" is not a boolean but an uint32.
-"regulator-over-current-protection" is not a valid entry for vref_ddr.
-LDO4 has a fixed voltage (3v3) so min/max entries are not allowed.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Fix the following dtbs_check warning:
spi-flash@0: $nodename:0: 'spi-flash@0' does not match '^flash(@.*)?$'
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: kernel@dh-electronics.com
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Fix the following dtbs_check warning:
eth@1,0: $nodename:0: 'eth@1,0' does not match '^ethernet(@.*)?$'
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: kernel@dh-electronics.com
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The Microchip LAN8710Ai PHY requires XTAL1/CLKIN external clock to be
enabled when the nRST is toggled according to datasheet Microchip
LAN8710A/LAN8710Ai DS00002164B page 35 section 3.8.5.1 Hardware Reset:
"
A Hardware reset is asserted by driving the nRST input pin low. When
driven, nRST should be held low for the minimum time detailed in
Section 5.5.3, "Power-On nRST & Configuration Strap Timing," on page
59 to ensure a proper transceiver reset. During a Hardware reset, an
external clock must be supplied to the XTAL1/CLKIN signal.
"
This is accidentally fulfilled in the current setup, where ETHCK_K is used
to supply both PHY XTAL1/CLKIN and is also fed back through eth_clk_fb to
supply ETHRX clock of the DWMAC. Hence, the DWMAC enables ETHRX clock,
that has ETHCK_K as parent, so ETHCK_K clock are also enabled, and then
the PHY reset toggles.
However, this is not always the case, e.g. in case the PHY XTAL1/CLKIN
clock are supplied by some other clock source than ETHCK_K or in case
ETHRX clock are not supplied by ETHCK_K. In the later case, ETHCK_K would
be kept disabled, while ETHRX clock would be enabled, so the PHY would
not be receiving XTAL1/CLKIN clock and the reset would fail.
Improve the DT by adding the PHY clock phandle into the PHY node, which
then also requires moving the PHY reset GPIO specifier in the same place
and that then also requires correct PHY reset GPIO timing, so add that
too.
A brief note regarding the timing, the datasheet says the reset should
stay asserted for at least 100uS and software should wait at least 200nS
after deassertion. Set both delays to 500uS which should be plenty.
Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Enable the CRC accelerator on all STM32MP15xx DHSOM based systems
and CRYP accelerator on all STM32MP15x[CF] DHSOM based systems.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Fill in the custom GPIO line names used by DH on the DHCOM SoM.
The GPIO line names are in accordance to DHCOM Design Guide R04
available at [1], section 3.9 GPIO.
[1] https://wiki.dh-electronics.com/images/5/52/DOC_DHCOM-Design-Guide_R04_2018-06-28.pdf
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The DHCOM SoM uSD slot has an optional voltage level translator, add
DT bindings which permit the MMCI driver to detect the translator
automatically.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Ludovic Barre <ludovic.barre@st.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-stm32@st-md-mailman.stormreply.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The STM32MP1 DHCOM SoM can be built with either bus voltage level shifter
or without one on the SDMMC1 interface. Because the SDMMC1 interface is
limited to 50 MHz and hence SD high-speed anyway, disable the SD feedback
clock to permit operation of the same U-Boot image on both SoM with and
without voltage level shifter.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The default state of SD bus and clock line is logical HI. SD card IO is
open-drain and pulls the bus lines LO. Always enable the SD bus pull ups
to guarantee this behavior on DHCOM SoM. Note that on SoMs with SD bus
voltage level shifter, the pull ups are built into the level shifter,
however that has no negative impact.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The uSD slot has no WP detection, disable it.
Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The DHCOM SoM uSD slot card detect signal is connected to GPIO PG1,
describe it in the DT.
Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Add bindings for the KS8851 ethernet present on the STM32MP1 DHCOM SoM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
On the production DHCOM STM32MP15xx SoM, the PHY IRQ line is connected
to the PI11 pin. Describe it in the DT as well, so the PHY IRQ can be
used e.g. to detect cable insertion and removal.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
The VDDA LDO1 PMIC output supplies the analog VDDA input of the
STM32MP1 on DHCOM, keep it always on, otherwise there could be
leakage through the SoC.
Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
The VIO regulator is supplied by PMIC Buck3, describe this in the DT.
Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
On the production revision of the SoM, 587-200, the PHY reset GPIO and
touchscreen IRQs are swapped to prevent collision between EXTi IRQs,
reflect that in DT.
Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
The QSPI CS2 is not used on DHCOM, remove the pinmux settings.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
The PHY and the VIO regulator is populated on the SoM, move it
into the SoM DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
The DH Electronics PDK2 can be populated with SoM with any STM32MP15xx
variant. Split the SoC-independent parts of the SoM and PDK2 into the
stm32mp15xx-dhcom-*.dtsi and reduce stm32mp157c-dhcom-*dts* to example
of adding STM32MP157C variant of the SoM into a PDK2 carrier board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
