| Age | Commit message (Collapse) | Author |
|---|
|
So far we've enabled pull-up and pull-down resistors on GPIOs using a
pinctrl node. Now that the GPIO binding allows for a flag to declare this,
let's switch to it.
This brings us closer to removing all the GPIO pinctrl nodes, which will in
turn allow us to switch the pinctrl strict mode on.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
While the USB PHY Device Tree mandates that the name of the VBUS detect pin
should be usb0_vbus_det-gpios, a significant number of device tree use
usb0_vbus_det-gpio instead.
This was functional because the GPIO framework falls back to the gpio
suffix that is legacy, but we should fix this.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
While the USB PHY Device Tree mandates that the name of the ID detect pin
should be usb0_id_det-gpios, a significant number of device tree use
usb0_id_det-gpio instead.
This was functional because the GPIO framework falls back to the gpio
suffix that is legacy, but we should fix this.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Almost all files in the kernel are either plain text or UTF-8 encoded. A
couple however are ISO_8859-1, usually just a few characters in a C
comments, for historic reasons.
This converts them all to UTF-8 for consistency.
Link: http://lkml.kernel.org/r/20180724111600.4158975-1-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Simon Horman <horms@verge.net.au> [IPVS portion]
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> [IIO]
Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc]
Acked-by: Rob Herring <robh@kernel.org>
Cc: Joe Perches <joe@perches.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Using the cd-inverted property is not useful when GPIOs are used as card
detects since the polarity can be specified with the usual
GPIO_ACTIVE_(HIGH|LOW) GPIO flags. It has also caused confusion for
U-Boot developers, so migrate all sunxi boards away from cd-inverted.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Some GPIO pinctrl nodes cannot be easily removed, because they would also
change the pin configuration, for example to add a pull resistor or change
the current delivered by the pin.
Those nodes still have underscores and unit-addresses in their node names
in our DTs, so adjust their name to remove the warnings. Use that occasion
to also fix some poorly chosen node-names.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The I2C's, MMC0 and EMAC controllers have only one muxing option in the
SoC. In such a case, we can just move the muxing into the DTSI, and remove
it from the DTS.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.
In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
One of the usage of the LRADC is to implement buttons. The bindings define
that we should have one subnode per button, with their associated voltage
as a property.
However, there was no reg property but we still used the voltage associated
to the button as the unit-address, which eventually generated warnings in
DTC.
Rename the node names to avoid those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
As part of our effort to move pinctrl/GPIO interlocking into the
driver where it belongs, this patch drops the definition and usage
of the mmc0_cd_pin_reference_design pinmux setting for the default
mmc0 card detect GPIO pin.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Now that we can handle the generic pinctrl bindings, convert our DT to it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The allwinner,drive property set to 10mA was really considered as our
default. Remove all those properties entirely to make that obvious.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add a node describing the focaltech ft5306de4 touchscreen found on
inet97fv2 tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Enable i2c1 and i2c2 controllers, these are used for the touchscreen resp.
the accelerometer.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Enable support for the tablet keys which are connected via the lradc.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Enable the otg controller on the inet97fv2 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Use axp209.dtsi and add regulator nodes for the regulators used on the
inet97fv2 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The inet97fv2 tablet only has a usb-2 wifi device connected to the second
ehci controller, disable the first ehci controller and both ohci
controllers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The FSF address triggers a warning on checkpatch, saying that the FSF
license is already present in the Linux source code, and that it has
already changed in the past.
Remove it from our DT, as suggested.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Add UART aliases and stdout-path property for all the Allwinner boards so that
we won't have to rely on the bootargs' console= value, while working with
legacy bootloaders.
While we're at it, also remove the mentions of earlyprintk in the bootargs,
that will remove our default bootargs entirely, and allow the kernel to boot on
a system even if DEBUG_LL is configured for another system.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Replace the various raw GPIO flags by their definition in the common
dt-bindings header.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Prepare the device trees to use the C preprocessor.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Acked-by: Hans de Goede <hdegoede@redhat.com>
|
|
At a node for the axp209, and where necessary the i2c controller to the dts
for various boards. Note the axp209 regulators are omitted as we don't have
any use for them yet, and on some boards were not sure how exactly they are
wired up.
Adding support for just the axp209 without the regulators is still useful, as
it will give us power-button and poweroff support.
Signed-off-by: Carlo Caione <carlo@caione.org>
[hdegoede@redhat.com: Drop the regulator bits for now]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Tested on a subset of these boards, for the others boards the settings match
the ones of the tested boards according to the original firmware fex files.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This patch adds basic support for the INet-97F_Rev_02 board found in various
low cost consumer tablet devices (http://linux-sunxi.org/INet-97F_Rev_02)
Signed-off-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
