| Age | Commit message (Collapse) | Author |
|---|
|
The I2C and MMC controllers have only one muxing option in the SoC. In such a
case, we can just move the muxing into the DTSI, and remove it from
the DTS.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.
In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Some boards override the MMC pin muxing settings in order to enable the
pull-ups and change the drive strength to a value higher than the default.
While this was needed in the earlier days, this is now the default setting
for those pins, and therefore we don't need those board-specific settings
anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Boards usually have an external pull-up on the card-detect signal, so
there's no need to add another one.
This also removes a DTC warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Using the cd-inverted property is not useful when GPIOs are used as card
detects since the polarity can be specified with the usual
GPIO_ACTIVE_(HIGH|LOW) GPIO flags. It has also caused confusion for
U-Boot developers, so migrate all sunxi boards away from cd-inverted.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
All dts files for the sunxi platform have been switched to the generic
pinconf bindings. As a result, the sunxi specific pinctrl macros are
no longer used.
Remove the #include entry with the following command:
sed --follow-symlinks -i -e '/pinctrl\/sun4i-a10.h/D' \
arch/arm/boot/dts/sun?i*.*
arch/arm/boot/dts/sun9i-a80.dtsi was then edited to remove the extra
empty line.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Now that we can handle the generic pinctrl bindings, convert our DT to it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The allwinner,drive property set to 10mA was really considered as our
default. Remove all those properties entirely to make that obvious.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This is the same issue fixed in commit dcf5341f0150 ("ARM: dts:
sun8i-q8-common: Do not set constraints on dc1sw regulator").
Commit message copied:
dc1sw is an on/off only regulator and as such it cannot have constraints.
This is a limitation of the kernel regulator implementation which resolves
supplies on the first regulator_get(), which is done after applying
constraints, and applying the constrains will fail because it calls
_regulator_get_voltage() and _regulator_do_set_voltage() both of which
will fail on a switch regulator when there is no supply (yet).
This causes registering of all axp22x regulators to fail with the
following errors:
[ 1.395249] vcc-lcd: failed to get the current voltage(-22)
[ 1.405131] axp20x-regulator axp20x-regulator: Failed to register dc1sw
[ 1.412436] axp20x-regulator: probe of axp20x-regulator failed with error -22
This commit removes the constrains on dc1sw / vcc-lcd fixing this problem.
Note that dcdc1 itself is contrained to the exact same values, so this
does not change anything.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Cc: <stable@vger.kernel.org> # 4.6
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Enable the axp221 PMIC chip in the dts file.
Allows board to power off correctly from the poweroff command
This board requires dc1sw to be enabled in order to provide a power source
for the 5V DCDC converter that powers USB2.
This board uses dldo1 for 3.3V wifi power
This board requires dldo3 to be enabled at 2.8V in order to provide voltage
to the pullup resistors for the i2c0 bus.
Signed-off-by: Lawrence Yu <lyu@micile.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The bs1078v2 is a pcb found in 10.1" tablets with an A31 soc, 1G RAM
and 8G NAND, rtl8723as usb wifi, 1 micro USB OTG port, 1 USB HOST port
This commit adds a dts for v2 of the bs1078 pcb.
Signed-off-by: Lawrence Yu <lyu@micile.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
