| Age | Commit message (Collapse) | Author |
|---|
|
Even though it translates to the same thing down to the binary level, we
should have an array of 2 number cells to describe each OPP, which in
turns create a validation warning.
Let's fix this.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20210901091852.479202-42-maxime@cerno.tech
|
|
The CPU thermal zone is called on most of the older DTSI cpu_thermal.
However, the underscore is an invalid character for a node name and the
thermal zone binding explicitly requires that zones are called
*-thermal. Let's fix it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20210114113538.1233933-8-maxime@cerno.tech
|
|
The hardware codec on the A10, A10s, A13 and A20 needs buffer in the
first 256MB of RAM. This was solved by setting the CMA pool at a fixed
address in that range.
However, in recent kernels there's something else that comes in and
reserve some range that end up conflicting with our default pool
requirement, and thus makes its reservation fail.
The video codec will then use buffers from the usual default pool,
outside of the range it can access, and will fail to decode anything.
Since we're only concerned about that 256MB, we can however relax the
allocation to just specify the range that's allowed, and not try to
enforce a specific address.
Fixes: 5949bc5602cc ("ARM: dts: sun4i-a10: Add Video Engine and reserved memory nodes")
Fixes: 960432010156 ("ARM: dts: sun5i: Add Video Engine and reserved memory nodes")
Fixes: c2a641a74850 ("ARM: dts: sun7i-a20: Add Video Engine and reserved memory nodes")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20200704130829.34297-1-maxime@cerno.tech
|
|
Define pins for LVDS channels 0 and 1, configure reset line for tcon0 and
provide sample LVDS panel, connected to tcon0.
Signed-off-by: Andrey Lebedev <andrey@lebedev.lt>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
The CSI controller driver now supports the second CSI controller, CSI1.
Add a device node for it. Pinmuxing options for the MCLK output, the
standard 8-bit interface, and a secondary 24-bit interface are included.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A slightly larger set of fixes have accrued in the last two weeks.
Mostly a collection of the usual smaller fixes:
- Marvell Armada: USB phy setup issues on Turris Mox
- Broadcom: GPIO/pinmux DT mapping corrections for Stingray, MMC bus
width fix for RPi Zero W, GPIO LED removal for RPI CM3. Also some
maintainer updates.
- OMAP: Fixlets for display config, interrupt settings for wifi, some
clock/PM pieces. Also IOMMU regression fix and a ti-sysc
no-watchdog regression fix.
- i.MX: A few fixes around PM/settings, some devicetree fixlets and
catching up with config option changes in DRM
- Rockchip: RockRro64 misc DT fixups, Hugsun X99 USB-C, Kevin display
panel settings
... and some smaller fixes for Davinci (backlight, McBSP DMA),
Allwinner (phy regulators, PMU removal on A64, etc)"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (42 commits)
ARM: dts: stm32: relax qspi pins slew-rate for stm32mp157
MAINTAINERS: Update the Spreadtrum SoC maintainer
MAINTAINERS: Remove Gregory and Brian for ARCH_BRCMSTB
ARM: dts: bcm2837-rpi-cm3: Avoid leds-gpio probing issue
bus: ti-sysc: Fix watchdog quirk handling
ARM: OMAP2+: Add pdata for OMAP3 ISP IOMMU
ARM: OMAP2+: Plug in device_enable/idle ops for IOMMUs
ARM: davinci_all_defconfig: enable GPIO backlight
ARM: davinci: dm365: Fix McBSP dma_slave_map entry
ARM: dts: bcm2835-rpi-zero-w: Fix bus-width of sdhci
ARM: imx_v6_v7_defconfig: Enable CONFIG_DRM_MSM
arm64: dts: imx8mn: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mm: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mq: Use correct clock for usdhc's ipg clk
ARM: dts: imx7s: Correct GPT's ipg clock source
ARM: dts: vf610-zii-scu4-aib: Specify 'i2c-mux-idle-disconnect'
ARM: dts: imx6q-logicpd: Re-Enable SNVS power key
arm64: dts: lx2160a: Correct CPU core idle state name
mailmap: Add Simon Arlott (replacement for expired email address)
arm64: dts: rockchip: Fix override mode for rk3399-kevin panel
...
|
|
What we thought would be the module clock is actually the clock meant to be
used by the sensors, and play no role in the CSI controller. Now that the
binding has been updated to reflect that, let's update the device tree too.
Fixes: d2b9c6444301 ("ARM: dts: sun7i: Add CSI0 controller")
Reported-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
This reverts commits 3d109bdca981 ("ARM: dts: sunxi: Remove useless
phy-names from EHCI and OHCI"), 0a3df8bb6dad ("ARM: dts: sunxi: h3/h5:
Remove useless phy-names from EHCI and OHCI") and 3c7ab90aaa28 ("arm64:
dts: allwinner: Remove useless phy-names from EHCI and OHCI").
It turns out that while the USB bindings were not mentionning it, the PHY
client bindings were mandating that phy-names is set when phys is. Let's
add it back.
Fixes: 3d109bdca981 ("ARM: dts: sunxi: Remove useless phy-names from EHCI and OHCI")
Fixes: 0a3df8bb6dad ("ARM: dts: sunxi: h3/h5: Remove useless phy-names from EHCI and OHCI")
Fixes: 3c7ab90aaa28 ("arm64: dts: allwinner: Remove useless phy-names from EHCI and OHCI")
Reported-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20191002112651.100504-1-mripard@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The watchdog has a clock on all our SoCs, but it wasn't always listed.
Add it to the devicetree where it's missing.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The watchdog has an interrupt on all our SoCs, but it wasn't always listed.
Add it to the devicetree where it's missing.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The CSI controller embedded in the A20 can be supported by our new driver.
Let's add it to our DT.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The DWMAC binding never supported having the Ethernet PHY node as a
direct child to the controller, nor did it support the "phy" property
as a way to specify which Ethernet PHY to use. What seemed to work
was simply the implementation ignoring the "phy" property and instead
probing all addresses on the MDIO bus and using the first available
one.
The recent switch from "phy" to "phy-handle" breaks the assumptions
of the implementation, and does not match what the binding requires.
The binding requires that if an MDIO bus is described, it shall be
a sub-node with the "snps,dwmac-mdio" compatible string.
Add a device node for the MDIO bus, and move the Ethernet PHY node
under it. Also fix up the #address-cells and #size-cells properties
where needed.
Fixes: de332de26d19 ("ARM: dts: sunxi: Switch from phy to phy-handle")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Neither the OHCI or EHCI bindings are using the phy-names property, so we
can just drop it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The NAND controller node name should be nand-controller and not nand as we
used previously according to the devicetree specification. Let's fix our
DTs.
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The recently added uart mux options had a few typos. Fix them.
Fixes: 43d0fe112585 ("ARM: dts: sun7i: add pinctrl for missing uart mux options")
Reported-by: Werner Böllmann <Werner.Boellmann@fh-dortmund.de>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The USB OTG binding we have mandates to have a dr_mode property, yet not
all boards are setting it.
Since the generic otg binding states that the default mode should be the
OTG mode, let's use that one in our DTSI.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Even though it doesn't make any difference at the binary level, the reg
property is an array of cells, and should be represented as such.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Even though we shouldn't really have any external user of the clock
provided by the TCON, if clock-output-names is set, then #clock-cells must
be there as well.
Fix this.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
As can be shown by the YAML schema now, the combination of GIC compatibles
we were using has never been an option.
Switch to the gic-400 variant, which is the more correct option.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Since only one alternative at a time is used, and some functions may not
be used at all, this cuts down the size of the board dtb files a bit.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
This adds pinctrl settings the EMAC using pins in the PH block.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
This adds pinctrl settings for the CAN controller using pins
PA16 and PA17.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
This adds pinctrl settings for various missing uart options.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
"arm,cortex-a15-pmu" is not a valid fallback compatible string for an
Cortex-A7 PMU, so drop it.
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The I2C and MMC controllers have only one muxing option in the SoC. In such a
case, we can just move the muxing into the DTSI, and remove it from
the DTS.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Our HDMI output endpoint on the A10s DTSI has a warning under DTC: "graph
node has single child node 'endpoint', #address-cells/#size-cells are not
necessary". Fix this by removing those properties.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Some UART nodes on the A20 DTSI do not share the same pattern that we use
everywhere else, with the RTS and CTS pins split away from the TX and RX
pins. Make those pin groups consistent with the rest of our DT.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.
In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The simple-framebuffer nodes have a unit address, but no reg property which
generates a warning when compiling it with DTC.
Change the simple-framebuffer node names so that there is no warnings on
this anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Our oscillators clock names have a unit address, but no reg property, which
generates a warning in DTC. Change these names to remove those unit
addresses.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Our main node for all the in-SoC controllers used to have a unit name. The
unit-name, in addition to being actually false, would not match any reg
property, which generates a warning.
Remove it in order to remove those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Using skeleton.dtsi will create a memory node that will generate a warning
in DTC. However, that node will be created by the bootloader, so we can
just remove it entirely in order to remove that warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
There's no phandle pointing to the CMA pool, so it's label is unnecessary.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The CMA node has a unit address, but no reg property which generates a
warning in DTC. Change the node name to reflect its usage and drop the unit
address.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
This adds nodes for the Video Engine and the associated reserved memory
for the A20. Up to 96 MiB of memory are dedicated to the CMA pool.
The VPU can only map the first 256 MiB of DRAM, so the reserved memory
pool has to be located in that area. Following Allwinner's decision in
downstream software, the last 96 MiB of the first 256 MiB of RAM are
reserved for this purpose.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
This adds support for the C1 SRAM region (to be used with the SRAM
controller driver) for the A20 platform. The region is shared
between the Video Engine and the CPU.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
[Maxime: Fixed the SRAM C size]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
This switches the sun7i-a20 dtsi to use the most qualified compatibles
for the system-control block (previously named SRAM controller) as well
as the SRAM blocks. The sun4i-a10 compatibles are kept since these
hardware blocks are backward-compatible.
The node name for system control is also updated to reflect the fact that
the controller described is really about system control rather than SRAM
control.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Fix other missing properties (clocks, OPP, clock latency) as well to
make it all work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The A20 has an ARM Mali 400 GPU, so add binding to our DT.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
a CPU cooling device is found by referring to the cpufreq table instead.
Remove the unused properties from the CPU nodes.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
Including sun4i header instead of sun7i prevents using sun7i specific
defines.
Substitute header inclusion in sun7i-a20.dtsi using right one.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
There is a copy-paste error in the display pipeline device tree graph.
The remote endpoint of the display backend 1's output to TCON0 points
to the wrong endpoint. This will result in the driver incorrectly
parsing the relationship of the components.
Reported-by: Andrea Venturi <ennesimamail.av@gmail.com>
Fixes: 0df4cf33a594 ("ARM: dts: sun4i: Add device nodes for display
pipelines")
Fixes: 5b92b29bed45 ("ARM: dts: sun7i: Add device nodes for display
pipelines")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
When the HDMI controller device node was added, the needed PLL clock
macros were not exported. A separate patch addresses that, but it is
merged through a different tree.
Now that both patches are in mainline proper, we can convert the raw
numbers to proper macros.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Pull "Allwinner DT changes for 4.15" from Maxime Ripard:
The most notable changes are:
- Conversion to the last SoC (A10, A20) to the new clock framework
- HDMI and dual pipeline support for the A10, A20 and A31 DRM driver
- Support for the various power supplies on a number of boards
- Fix of DTC warnings on a number of SoCs, but most of them still need
some work
- New boards: A20-OLinuXino-MICRO-eMMC, TBS A711, Banana Pi M2 Berry,
Banana Pi M2 Ultra
- New R40 SoC support
* tag 'sunxi-dt-for-4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (63 commits)
ARM: sun8i: r40: enable USB host for Banana Pi M2 Ultra
ARM: sun8i: v40: add 5V regulator for Banana Pi M2 Berry
ARM: sun8i: r40: add 5V regulator for Banana Pi M2 Ultra
ARM: sun8i: r40: add USB host port nodes for R40
ARM: dts: sun4i: Enable HDMI support on some A10 devices
ARM: dts: sun7i: Enable HDMI support on some A20 devices
ARM: dts: sun7i: Add device nodes for display pipelines
ARM: dts: sun4i: Add device nodes for display pipelines
ARM: dts: sun8i: r40: add watchdog device node
ARM: dts: sun5i: reference-design-tablet: Enable AXP209 AC and battery
ARM: dts: sun9i: Change node names to remove underscores
ARM: dts: sun9i: Change node names to remove underscores
ARM: dts: sun4i: Remove underscores from nodes names
ARM: dts: sun4i: Provide default muxing for relevant controllers
ARM: dts: sun4i: Change pinctrl nodes to avoid warning
ARM: dts: sun6i: Enable HDMI support on some A31/A31s devices
ARM: dts: sun6i: Add device node for HDMI controller
ARM: dts: sun4i: Change LRADC node names to avoid warnings
ARM: dts: sun4i: Remove skeleton and memory to avoid warnings
ARM: dts: sun4i: Remove gpio-keys warnings
...
|
|
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm/boot/dts -type -f -name '*.dts*'
Dropped changes to ARM, Ltd. boards LED nodes and manually fixed up some
occurrences of uppercase hex.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The A20 has two interconnected display pipelines, mirroring the A10.
Add all the device nodes for them, including the downstream HDMI
controller that we already support.
Signed-off-by: Jonathan Liu <net147@gmail.com>
[wens@csie.org: Squashed in HDMI and provided commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Most of our device trees have had leading zeros for padding as part of
the nodes unit-addresses.
Remove all these useless zeros that generate warnings
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Convert sun7i-a20.dtsi to new CCU driver.
Tested on Cubietruck.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Add SoC specific compatibles for all sunXi crypto nodes, in addition to
the one already used (allwinner,sun4i-a10-crypto).
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
