| Age | Commit message (Collapse) | Author |
|---|
|
Since the libretech-all-h3-cc can use either the H2+, H3 or H5, move the
content of the dts file to a common dtsi file to be included by the H3
variant and in a following patch the H5 variant.
By the way, update the SPDX licence tag position.
Suggested-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The voltage of the VCC-1V2 regulator on the ALL-H3-CC H3 ver. should be
1.2V, not the 3.3V currently defined in the device tree.
Fix the voltage in the device tree.
Fixes: 6ca358645d4d ("ARM: dts: sun8i: h3: Add dts file for Libre
Computer Board ALL-H3-CC H3 ver.")
Cc: <stable@vger.kernel.org> # 4.16.x
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The ALL-H3-CC has a fixed VDD-CPUX voltage at 1.2V, which is supplied
by a regulator.
Set the CPU's cpu-supply property to the VDD-CPUX regulator.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[wens@csie.org: Fix device node ordering]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The VDD-CPUX voltage of ALL-H3-CC H3 ver should be 1.2V, not the 3.3V
currently defined in the device tree.
Fix the voltage in the device tree.
Fixes: 6ca358645d4d ("ARM: dts: sun8i: h3: Add dts file for Libre Computer Board ALL-H3-CC H3 ver.")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Cc: <stable@vger.kernel.org> # 4.16.x
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
Enable HDMI output on all boards which have HDMI connector.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Most of the boards use the mmc0 pins and their attributes defined in
mmc0_pins_a. Let's default to those by moving the pinctrl attributes
to the dtsi file. This makes it easier to modify device trees in the
future as there is only one place to change the pinctrl attributes.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Using the cd-inverted property is not useful when GPIOs are used as card
detects since the polarity can be specified with the usual
GPIO_ACTIVE_(HIGH|LOW) GPIO flags. It has also caused confusion for
U-Boot developers, so migrate all sunxi boards away from cd-inverted.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The Libre Computer Board ALL-H3-CC from Libre Technology is a Raspberry
Pi B+ form factor single board computer based on the Allwinner H3 SoC.
The board has 1GB DDR3 SDRAM, provided by 4 2Gb chips. The mounting holes
and connectors are in the exact same position as on the Raspberry Pi B+.
Raspberry Pi B+ like peripherals supported on this board include:
- Power input through micro-USB connector (without USB OTG)
- Native 100 Mbps ethernet using the internal PHY, as opposed to
USB-based on the RPi
- 4x USB 2.0 host ports, directly connected to the SoC, as opposed to
being connected through a USB 2.0 hub on the RPi
- TV and audio output on a 3.5mm TRRS jack
- HDMI output
- Micro-SD card slot
- Standard RPi B+ GPIO header, with the standard peripherals routed to
the same pins.
* 5V, 3.3V power, and ground
* I2C0 on the H3 is routed to I2C1 pins on the RPi header
* I2C1 on the H3 is routed to I2C0 pins on the RPi header
* UART1 on the H3 is routed to UART0 pins on the RPi header
* SPI0 on the H3 is routed to SPI0 pins on the RPi header,
with GPIO pin PA17 replacing the missing Chip Select 1
* I2S1 on the H3 is routed to PCM pins on the RPi header
- Additional peripherals from the H3 are available on different pins.
These include I2S0, JTAG, PWM1, SPDIF, SPI1, and UART3
In addition, there are a number of new features:
- Console UART header
- Consumer IR receiver
- Camera interface (not compatible with RPi)
- Onboard microphone
- eMMC expansion module port
- Heatsink mounting holes
- Power button
The power button requires corresponding software for the embedded
coprocessor to properly function.
This patch adds a dts file for this board that enables all "onboard"
peripherals currently supported. This means no display or camera
support.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
