| Age | Commit message (Collapse) | Author |
|---|
|
The XUSB pad controller is responsible for supplying power to the PLLs
used to drive the various USB, PCI and SATA pads. Move the PLL power
supplies from the PCIe and XUSB controllers to the XUSB pad controller
to make sure they are available when needed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Parentheses in the SPDX license identifier are only used to group sub-
expressions. If there's no need for such grouping, the parentheses can
be omitted.
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Shorten temperature-sensor node to just temp-sensor as suggested
in the binding documentation.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Get rid of the fake clocks simple bus and use node names as per the
actual schematics.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
As underscores in node names are not recommended replace them all where
possible with dashes.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Drop model and compatible nodes from the module level device tree as
they get overridden by the carrier board device tree anyway.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Reorder CPU DFLL clock properties.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add mmc-ddr-1_8v property enabling eMMC DDR52 mode.
root@apalis-tk1-mainline:~# cat /sys/kernel/debug/mmc2/ios
clock: 52000000 Hz
actual clock: 52000000 Hz
vdd: 21 (3.3 ~ 3.4 V)
bus mode: 2 (push-pull)
chip select: 0 (don't care)
power mode: 2 (on)
bus width: 3 (8 bits)
timing spec: 8 (mmc DDR52)
signal voltage: 1 (1.80 V)
driver type: 0 (driver type B)
root@apalis-tk1-mainline:~# hdparm -t /dev/mmcblk2
/dev/mmcblk2:
Timing buffered disk reads: 256 MB in 3.02 seconds = 84.83 MB/sec
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add proper eMMC vmmc and vqmmc supplies e.g. fixing signalling voltage.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
White-space clean-up.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Drop unused pinmux label.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add missing regulators:
- reg_module_3v3_audio being VDDA supply of SGTL5000
- VDDD supply of SGTL5000 actually being reg_1v8_vio
- TMP451 temperature sensor vcc supply being reg_module_3v3
- usb3-0 vbus supply being reg_usbh_vbus
- usb3-1 vbus supply being reg_usbo1_vbus
- carrier board HDMI supply being reg_5v0
- carrier board sata target 5v supply being reg_5v0
- carrier board sata target 12v supply being reg_12v0
- carrier board reg_3v3 actually being backlight power supply
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Just cosmetic regulator clean-up.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Reorder padctl properties.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Reorder Host1x/HDMI properties.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add empty local-mac-address property to be filled in by boot loader
(e.g. U-Boot).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add a generic /memory node in each Tegra DTSI (with empty reg property,
to be overidden by each DTS) and set proper unit address for /memory
nodes to fix the DTC warnings:
arch/arm/boot/dts/tegra20-harmony.dtb: Warning (unit_address_vs_reg):
/memory: node has a reg or ranges property, but no unit name
The DTB after the change is the same as before except adding
unit-address to /memory node.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Turns out the compatible "nvidia,tegra124-hsuart" does not (yet) exist
and everybody else also uses it only in conjunction with
"nvidia,tegra30-hsuart".
Reported-by: Martin Šafařík <msafarik@retia.cz>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Support the V1.2 hardware revision with the following pin muxing
changes:
Ddc_scl_pv4 and ddc_sda_pv5 previously used as Apalis GPIO3 and GPIO4
are now used as DDC pins.
Gen2_i2c_scl_pt5 and gen2_i2c_sda_pt6 previously used as DDC pins are
now used as USB power enable signals.
Usb_vbus_en0_pn4 and usb_vbus_en1_pn5 previously used as USB power
enable signals are now used as GPIO3 and GPIO4.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
