| Age | Commit message (Collapse) | Author |
|---|
|
The LM90 temperature sensor should use edge-triggered interrupt because
LM90 hardware doesn't deassert interrupt line until temperature is back
to normal state, which results in interrupt storm. Correct the interrupt
trigger type.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
All Tegra boards which use WM8903 audio codec are specifying a wrong
polarity for the headphones detection GPIO. The kernel driver hardcodes
the polarity to active-low, which is the correct polarity, so we can fix
the device-trees safely.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Specify TPS65911 as wakeup source on Tegra devices in order to allow
its RTC to wake up system from suspend by default instead of requiring
wakeup to be enabled manually via sysfs.
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Enable CPU thermal throttling on Tegra30 Cardhu board.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
variants
Enable CPU frequency and voltage scaling on all Tegra30 Cardhu board
variants.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The new json-schema based validation tools require SD/MMC controller
nodes to be named mmc. Rename all references to them.
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The standard way to do this is to list out the regulators at the top
level. Adopt the standard way to fix validation.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The standard way to do this is to list out the clocks at the top-level.
Adopt the standard way to fix validation.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
"simple-panel" is a Linux driver and has never been an accepted upstream
compatible string, so remove it.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
clk_out_1, clk_out_2, and clk_out_3 are part of Tegra PMC block but were
previously erroneously provided by the clock and reset controller.
clk_out_1 is dedicated for audio mclk on Tegra30 through Tegra210.
This patch updates device tree sound node to use clk_out_1 from the PMC
provider as mclk and uses assigned-clock properties to specify clock
parents for clk_out_1 and extern1.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Starting with commit 8947e396a829 ("Documentation: dt: mtd: replace
"nor-jedec" binding with "jedec, spi-nor"") we have "jedec,spi-nor"
binding indicating support for JEDEC identification.
Use it for all flashes that are supposed to support READ ID op according
to the datasheets.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add a generic /memory node in each Tegra DTSI (with empty reg property,
to be overidden by each DTS) and set proper unit address for /memory
nodes to fix the DTC warnings:
arch/arm/boot/dts/tegra20-harmony.dtb: Warning (unit_address_vs_reg):
/memory: node has a reg or ranges property, but no unit name
The DTB after the change is the same as before except adding
unit-address to /memory node.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
On all versions of Tegra30 Cardhu, the reset signal to the NXP PCA9546
I2C mux is connected to the Tegra GPIO BB0. Currently, this pin on the
Tegra is not configured as a GPIO but as a special-function IO (SFIO)
that is multiplexing the pin to an I2S controller. On exiting system
suspend, I2C commands sent to the PCA9546 are failing because there is
no ACK. Although it is not possible to see exactly what is happening
to the reset during suspend, by ensuring it is configured as a GPIO
and driven high, to de-assert the reset, the failures are no longer
seen.
Please note that this GPIO is also used to drive the reset signal
going to the camera connector on the board. However, given that there
is no camera support currently for Cardhu, this should not have any
impact.
Fixes: 40431d16ff11 ("ARM: tegra: enable PCA9546 on Cardhu")
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
dtc recently added PCI bus checks. Fix these warnings.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This seems to have been copied and pasted since the beginning of time,
though only until Tegra124, likely because that DT was written from
scratch or it was fixed along the way.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
For Tegra boards, the device-tree alias serial0 is used for the console
and so add the stdout-path information so that the console no longer
needs to be passed via the kernel boot parameters.
This has been tested on boards, tegra20-trimslice, tegra30-beaver,
tegra114-dalmore and tegra124-jetson-tk1.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "nvidia,wakeup-source" boolean property to enable the
wakeup source, "wakeup-source" is the new standard binding.
This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any further copy-paste
duplication.
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The word "sticker" was misspelled as "stciker". Fix it.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
[treding@nvidia.com: add a brief commit message]
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Cardhu has a power key on the top-right as well as volume up and
volume down keys on the right side.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
"isil" and "isl" prefixes are used at various locations inside the kernel
to reference Intersil corporation. This patch is part of a series fixing
those locations were "isl" is used in compatible strings to use the now
expected "isil" prefix instead (NASDAQ symbol for Intersil and most used
version).
Note: isl29028 is an I2C device so the patch does not in fact currently
depend on the introduction of "isil"-based compatible string in isl29028
driver because I2C core does not check the prefix yet.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Arnd Bergmann:
"The DT branch adds a lot of new stuff for additional SoC and board
support. The branch is the largest one and contains 513 out of the
total 972 non-merge arm-soc changesets for 3.19.
Most of the changes are about enabling additional on-chip devices for
existing machines, but there are also an unusual number of new SoC
types being added this time:
- AMLogic Meson8
- ARM Realview in DT mode
- Allwinner A80
- Broadcom BCM47081
- Broadcom Cygnus
- Freescale LS1021A
- Freescale Vybrid 500 series
- Mediatek MT6592, MT8127, MT8135
- STMicroelectronics STiH410
- Samsung Exynos4415
The level of support for the above differs widely, some are just stubs
with nothing more than CPU, memory and a UART, but others are fairly
complete. As usual, these get extended over time.
There are also many new boards getting added, this is the list of
model strings that are showing up in new dts files:
- ARM RealView PB1176
- Altera SOCFPGA Arria 10
- Asus RT-N18U (BCM47081)
- Buffalo WZR-1750DHP (BCM4708)
- Buffalo WZR-600DHP2 (BCM47081)
- Cygnus Enterprise Phone (BCM911360_ENTPHN)
- D-Link DIR-665
- Google Spring
- IGEP COM MODULE Rev. G (TI OMAP AM/DM37x)
- IGEPv2 Rev. F (TI OMAP AM/DM37x)
- LS1021A QDS Board
- LS1021A TWR Board
- LeMaker Banana Pi
- MarsBoard RK3066
- MediaTek MT8127 Moose Board
- MediaTek MT8135 evaluation board
- Mele M3
- Merrii A80 Optimus Board
- Netgear R6300 V2 (BCM4708)
- Nomadik STN8815NHK
- NovaTech OrionLXm
- Olimex A20-OLinuXino-LIME2
- Raspberry Pi Model B+
- STiH410 B2120
- Samsung Monk board
- Samsung Rinato board
- Synology DS213j
- Synology DS414
- TBS2910 Matrix ARM mini PC
- TI AM5728 BeagleBoard-X15
- Toradex Colibri VF50 on Colibri Evaluation Board
- Zynq ZYBO Development Board
Other notable changes include:
- exynos: cleanup of existing dts files
- mvebu: improved pinctrl support for Armada 370/XP
- nomadik: restructuring dts files
- omap: added CAN bus support
- shmobile: added clock support for some SoCs
- shmobile: added sound support for some SoCs
- sirf: reset controller support
- sunxi: continuing the relicensing under dual GPL/MIT
- sunxi: lots of new on-chip device support
- sunxi: working simplefb support (long awaited)
- various: provide stdout-path property for earlycon"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (510 commits)
ARM: dts: rk3288: add arm,cpu-registers-not-fw-configured
Revert "ARM: dts: rockchip: temporarily disable smp on rk3288"
ARM: BCM5301X: Add DT for Buffalo WZR-600DHP2
ARM: BCM5301X: Add DT for Asus RT-N18U
ARM: BCM5301X: Add DT for Buffalo WZR-1750DHP
ARM: BCM5301X: Add DT for Netgear R6300 V2
ARM: BCM5301X: Add buttons for Netgear R6250
ARM: dts: rockchip: Add input voltage supply regulators in pmic for Marsboard
ARM: BCM5301X: Add IRQs to Broadcom's bus-axi in DTS file
arm: dts: zynq: Add Digilent ZYBO board
arm: dts: zynq: Move crystal freq. to board level
doc: dt: vendor-prefixes: Add Digilent Inc
Documentation: devicetree: Fix Xilinx VDMA specification
ARM: dts: rockchip: set FIFO size for SDMMC, SDIO and EMMC on rk3066 and rk3188
ARM: dts: rockchip: add label property for leds on Radxa Rock
ARM: BCM5301X: Add LEDs for Netgear R6250 V1
ARM: BCM5301X: Add Broadcom's bus-axi to the DTS file
ARM: dts: add sysreg phandle to i2c device nodes for exynos
ARM: dts: Remove unused bootargs from exynos3250-rinato
ARM: dts: add board dts file for Exynos3250-based Monk board
...
|
|
compatible property
This patch corrects the vendor-prefix for isl29028 in the compatible property from
"isil,isl29028" to "isl,isl29028" according to listed vendor-prefixes in
Documentation/devicetree/bindings/vendor-prefixes.txt. Incorrect vendor-prefix "isl"
was reported by checkpatch.pl warning for drivers/staging/iio/light/isl29028.c.
Thus incorrect vendor-prefix "isil" was corrected for every mention of device isl29028.
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
There are general changes pending to make the /aliases/serial* entries
number the serial ports on the system. On Tegra, so far the ports have
been just numbered dynamically as they are configured so that makes them
change.
To avoid this, add specific aliases per board to keep the old numbers.
This allows us to change the numbering by default on future SoCs while
keeping the numbering on existing boards.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
These properties are deprecated and no longer of any use.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
These new properties more accurately reflect the real connections of the
boards and therefore make it easier to match them up with schematics.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
Merge "ARM: tegra: device tree changes for 3.15" from Stephen Warren:
This enables:
- host1x and eDP support on Tegra124.
- LCD panel support for a few Tegra20 devices and Venice2.
- Enables power down, SPI flash, and USB on Venice2.
- Documents which Dalmore revision is supported.
- Adds an I2C bus mux to Cardhu.
Additionally, Tegra124 is converted to use #address-cells=<2> since the
HW suports more than 32-bits of address space, and various cleanups are
included.
* tag 'tegra-for-3.15-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (21 commits)
ARM: dts: tegra: add PCIe interrupt mapping properties
ARM: tegra: use 2 address cells for Tegra124 DT
ARM: tegra: Rename as3722 node to pmic
ARM: tegra: Fix whitespace around '='
ARM: tegra: Enable USB on Venice2
ARM: tegra: Add Tegra124 USB support
ARM: tegra: Enable eDP for Venice2
ARM: tegra: Add Tegra124 eDP support
ARM: tegra: Add Tegra124 host1x support
ARM: tegra: Hook up SDMMC3 power-supply on Venice2
ARM: tegra: Overhaul Venice2 regulators
ARM: tegra: Combine VBUS enable pins into one node
ARM: tegra: Use "disabled" for status property
ARM: tegra: add SPI flash to Venice2 DT
ARM: tegra: enable PCA9546 on Cardhu
ARM: tegra: enable LCD panel on Ventana
ARM: tegra: enable LCD panel on Seaboard
ARM: tegra: add system-power-controller property for PMIC node
ARM: tegra: document which Dalmore revisions are supported
ARM: tegra: Properly sort clocks property
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Cardhu has a PCA9546 for I2C bus extension, which connects to 3
cameras. It's required for Tegra V4L2 soc camera driver and camera
sensor drivers.
Signed-off-by: Bryan Wu <pengw@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
This alias entry was evidently cut/paste from a different board, and
not correctly updated to match Cardhu. Fix this.
Fixes: 553c0a200e20 ("ARM: tegra: set up /aliases entries for RTCs")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add backlight and panel nodes for the Cardhu 10.1" WXGA TFT LCD panel.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
This ensures that the PMIC RTC provides the system time, rather than
the on-SoC RTC, which is not battery-backed.
tegra124-venice2.dts isn't touched yet since we haven't added any off-
SoC RTC device to its device tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Use Tegra pinconrol dt-binding macro to set the values of different pinmux
properties of Tegra30 platforms.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
For Tegra DT files, I've been attempting to keep the nodes sorted in
the order:
1) Nodes with reg, in order of reg.
2) Nodes without reg, alphabetically.
This patch fixes a few escapees that I missed:-(
The diffs look larger than they really are, because sometimes when one
node was moved up or down, diff chose to represent this as many other
nodes being moved the other way!
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
DT node names should include a unit address iff the node has a reg
property. For Tegra DTs at least, we were previously applying a different
rule, namely that node names only needed to include a unit address if it
was required to make the node name unique. Consequently, many unit
addresses are missing. Add them.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Add vcc-supply property in the nct1008 node, and set it
as sys_3v3_reg.
change the name of this node to temp-sensor.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Add device tree entries for the 3 USB controllers and PHYs and
enable the third controller on Cardhu and Beaver boards.
Fix VBUS regulator entries on Beaver. The GPIO pins were wrong.
Also, internal pullups need to be enabled on those pins.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Root port 2 is routed to the bottom connector on Cardhu and is used by
the development dock to provide gigabit ethernet and USB functionality.
Signed-off-by: Jay Agarwal <jagarwal@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Enabling the LP1 suspend mode for Tegra devices.
Tested-by: Marc Dietrich <marvin24@gmx.de> # paz00 board
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Nodes should be sorted by reg. Fix location of the tps62361 node.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Enable thermal sensor nct1008 for Tegra30 Cardhu.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Use the Tegra30 CAR binding header (tegra30-car.h) to replace magic
numbers in the device tree. For example,
- clocks = <&tegra_car 28>;
+ clocks = <&tegra_car CLK_HOST1X>;
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
[swarren, updated since tegra30-car.h moved for consistency]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Use the GIC and standard IRQ binding defines in all IRQ specifiers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Use TEGRA_GPIO() macro to name all GPIOs referenced by GPIO properties,
and some interrupts properties. Use standard GPIO flag defines too.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Replace /include/ (dtc) with #include (C pre-processor) for all Tegra DT
files, so that gcc -E handles the entire include tree, and hence any of
those files can #include some other file e.g. for constant definitions.
This allows future use of #defines and header files in order to define
names for various constants, such as the IDs and flags in GPIO
specifiers. Use of those features will increase the readability of the
device tree files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Adding the PM configuration of PMC when the platform support suspend
function.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
This patch adds "non-removable" property of MMC host where the eMMC device
is for Tegra platform.
And the "keep-power-in-suspend" property was used for the SDIO device that
need this to go into suspend mode (e.g. BRCM43xx series).
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Audio-related clocks need to be represented in the device tree. Update
bindings to describe which clocks are needed, and DT files to include
those clocks.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Adding the bindings of the clock source of PMC in DT.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
The GPIO pin of SD slot card detection should active low.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
No Tegra30 Platform is running PLL_P at another rate than 408MHz, nor is
any using any other PLL as UART source clock. Move attribute into SoC
level dtsi file to slim down board DT files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
