| Age | Commit message (Collapse) | Author |
|---|
|
All registers are located within 0x400 size from the base address.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add UniPhier AIDET (ARM Interrupt Detector) nodes to support
active low interrupts.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add NAND controller node to LD4, Pro4, sLD8, Pro5, and PXs2.
Set up pinctrl to enable 2 chip select lines except Pro4. The CS1
for Pro4 is multiplexed with other peripherals such as UART2, so
I did not enable it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
To include dt-bindings headers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Commit fa53757bca33 ("ARM: dts: uniphier: use SPDX-License-Identifier")
missed to touch these two. Now updating.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Compiling the UniPhier DT files with W=1, DTC warns like follows:
Warning (simple_bus_reg): Node /soc/system-bus@58c00000/support_card@1,1f00000/ethernet@00000000 simple-bus unit address format error, expected "0"
Warning (simple_bus_reg): Node /soc/system-bus@58c00000/support_card@1,1f00000/uart@000b0000 simple-bus unit address format error, expected "b0000"
Warning (simple_bus_reg): Node /soc/smpctrl@59800000 simple-bus unit address format error, expected "59801000"
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Commit 9c0da3cc61f1 ("ARM: dts: explicitly mark skeleton.dtsi as
deprecated") declared that skeleton.dtsi was deprecated.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
I notice some mistakes in the SoC DTSI; wrong interrupts properties
of timer nodes, mismatch between the node name and the compatible
for sdctrl block. Given those problems fixed, the common parts
among SoCs are less than I had first expected. The more and more
property overrides are making the SoC DTSI unreadable.
Stretch out the SoC DTSI files and fix the following:
- Fix the 3rd cell of the interrupts property of the timer nodes
for Pro4, Pro5, PXs2
- Fix the node name mioctrl to sdctrl for Pro5, PXs2
- Fix the second region of l2 node for PXs2
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add a CPU clock to every CPU node and a CPU OPP table to use the
generic cpufreq driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
I made a mistake bacuse the Media I/O block is not implemented in
these SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The UniPhier reset controller driver has been merged. Enable it.
Also, replace the fixed-rate clocks with the dedicated clock
drivers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Use PSCI for enable-method instead of SoC specific implementation.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
All UniPhier device trees have the common prefix "uniphier-", so
"ph1-" is just making names longer. Recent documents and other
projects are not using PH1- prefixes any more.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
