| Age | Commit message (Collapse) | Author |
|---|
|
This change disables the DMA support (RX/TX) on the NXP's fsl_lpuart
driver - the PIO mode is used instead. This change is necessary for better
robustness of BK4's device use cases with many potentially interrupted
short serial transfers.
Without it the driver hangs when some distortion happens on UART lines.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Before this change the device tree description of qspi node for
second memory on BK4 board was wrong (applicable to old, removed
fsl-quadspi.c driver).
As a result this memory was not recognized correctly when used
with the new spi-fsl-qspi.c driver.
From the dt-bindings:
"Required SPI slave node properties:
- reg: There are two buses (A and B) with two chip selects each.
This encodes to which bus and CS the flash is connected:
<0>: Bus A, CS 0
<1>: Bus A, CS 1
<2>: Bus B, CS 0
<3>: Bus B, CS 1"
According to above with new driver the second SPI-NOR memory shall
have reg=<2> as it is connected to Bus B, CS 0.
Fixes: a67d2c52a82f ("ARM: dts: Add support for Liebherr's BK4 device (vf610 based)")
Suggested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Pull ARM SoC device tree updates from Arnd Bergmann:
"This is a smaller update than the past few times, but with just over
500 non-merge changesets still dwarfes the rest of the SoC tree.
Three new SoC platforms get added, each one a follow-up to an existing
product, and added here in combination with a reference platform:
- Renesas RZ/A2M (R7S9210) 32-bit Cortex-A9 Real-time imaging
processor:
https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rza/rza2m.html
- Renesas RZ/G2E (r8a774c0) 64-bit Cortex-A53 SoC "for Rich Graphics
Applications":
https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rzg/rzg2e.html
- NXP i.MX8QuadXPlus 64-bit Cortex-A35 SoC:
https://www.nxp.com/products/processors-and-microcontrollers/arm-based-processors-and-mcus/i.mx-applications-processors/i.mx-8-processors/i.mx-8x-family-arm-cortex-a35-3d-graphics-4k-video-dsp-error-correcting-code-on-ddr:i.MX8X
These are actual commercial products we now support with an in-kernel
device tree source file:
- Bosch Guardian is a product made by Bosch Power Tools GmbH, based
on the Texas Instruments AM335x chip
- Winterland IceBoard is a Texas Instruments AM3874 based machine
used in telescopes at the south pole and elsewhere, see commit
d031773169df2 for some pointers:
- Inspur on5263m5 is an x86 server platform with an Aspeed ast2500
baseboard management controller. This is for running on the BMC.
- Zodiac Digital Tapping Unit, apparently a kind of ethernet switch
used in airplanes.
- Phicomm K3 is a WiFi router based on Broadcom bcm47094
- Methode Electronics uDPU FTTdp distribution point unit
- X96 Max, a generic TV box based on Amlogic G12a (S905X2)
- NVIDIA Shield TV (Darcy) based on Tegra210
And then there are several new SBC, evaluation, development or modular
systems that we add:
- Three new Rockchips rk3399 based boards:
- FriendlyElec NanoPC-T4 and NanoPi M4
- Radxa ROCK Pi 4
- Five new i.MX6 family SoM modules and boards for industrial
products:
- Logic PD i.MX6QD SoM and evaluation baseboad
- Y Soft IOTA Draco/Hydra/Ursa family boards based on i.MX6DL
- Phytec phyCORE i.MX6 UltraLite SoM and evaluation module
- MYIR Tech MYD-LPC4357 development based on the NXP lpc4357
microcontroller
- Chameleon96, an Intel/Altera Cyclone5 based FPGA development system
in 96boards form factor
- Arm Fixed Virtual Platforms(FVP) Base RevC, a purely virtual
platform for corresponding to the latest "fast model"
- Another Raspberry Pi variant: Model 3 A+, supported both in 32-bit
and 64-bit mode.
- Oxalis Evalkit V100 based on NXP Layerscape LS1012a, in 96Boards
enterprise form factor
- Elgin RV1108 R1 development board based on 32-bit Rockchips RV1108
For already supported boards and SoCs, we often add support for new
devices after merging the drivers. This time, the largest changes
include updates for
- STMicroelectronics stm32mp1, which was now formally launched last
week
- Qualcomm Snapdragon 845, a high-end phone and low-end laptop chip
- Action Semi S700
- TI AM654x, their recently merged 64-bit SoC from the OMAP family
- Various Amlogic Meson SoCs
- Mediatek MT2712
- NVIDIA Tegra186 and Tegra210
- The ancient NXP lpc32xx family
- Samsung s5pv210, used in some older mobile phones
Many other chips see smaller updates and bugfixes beyond that"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (506 commits)
ARM: dts: exynos: Fix max voltage for buck8 regulator on Odroid XU3/XU4
dt-bindings: net: ti: deprecate cpsw-phy-sel bindings
ARM: dts: am335x: switch to use phy-gmii-sel
ARM: dts: am4372: switch to use phy-gmii-sel
ARM: dts: dm814x: switch to use phy-gmii-sel
ARM: dts: dra7: switch to use phy-gmii-sel
arch: arm: dts: kirkwood-rd88f6281: Remove disabled marvell,dsa reference
ARM: dts: exynos: Add support for secondary DAI to Odroid XU4
ARM: dts: exynos: Add support for secondary DAI to Odroid XU3
ARM: dts: exynos: Disable ARM PMU on Odroid XU3-lite
ARM: dts: exynos: Add stdout path property to Arndale board
ARM: dts: exynos: Add minimal clkout parameters to Exynos3250 PMU
ARM: dts: exynos: Enable ADC on Odroid HC1
arm64: dts: sprd: Remove wildcard compatible string
arm64: dts: sprd: Add SC27XX fuel gauge device
arm64: dts: sprd: Add SC2731 charger device
arm64: dts: sprd: Add ADC calibration support
arm64: dts: sprd: Remove PMIC INTC irq trigger type
arm64: dts: rockchip: Enable tsadc device on rock960
ARM: dts: rockchip: add chosen node on veyron devices
...
|
|
The dspi3 is used as slave controller on vf610-bk4, and the default
'#address-cells = <1>;' setting in vfxxx.dtsi causes the following DTC
warning.
DTC arch/arm/boot/dts/vf610-bk4.dtb
../arch/arm/boot/dts/vfxxx.dtsi:550.24-563.6: Warning (spi_bus_bridge): /soc/aips-bus@40080000/spi@400ad000: incorrect #address-cells for SPI bus
also defined at ../arch/arm/boot/dts/vf610-bk4.dts:107.8-119.3
arch/arm/boot/dts/vf610-bk4.dtb: Warning (spi_bus_reg): Failed prerequisite 'spi_bus_bridge'
For spi device used as slave controller, '#address-cells' should be 0.
Let's overwrite the property in vf610-bk4.dts to fix the warning.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The procedure to read this ID value is as follows:
rmmod spi_fsl_dspi
insmod spi-gpio.ko
echo 504 > /sys/class/gpio/export
cat /sys/class/gpio/gpio504/value
...
echo 511 > /sys/class/gpio/export
cat /sys/class/gpio/gpio511/value
rmmod spi-gpio.ko
insmod spi_fsl_dspi
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Boards based on vf500/vf600 have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the vf500.dtsi/vf610m4.dtsi files.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This commit adds DTS support for BK4 device from Liebherr. It
uses vf610 SoC from NXP.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
