| Age | Commit message (Collapse) | Author |
|---|
|
The NANDF_CS2 pad is also part of the wlan-vmmcgrp iomux group.
Removing is from the usdhc2grp group avoids the following error:
imx6q-pinctrl 20e0000.iomuxc: pin MX6Q_PAD_NANDF_CS2 already requested
by regulators:regulator@4; cannot claim for 2194000.usdhc
imx6q-pinctrl 20e0000.iomuxc: pin-187 (2194000.usdhc) status -22
imx6q-pinctrl 20e0000.iomuxc: could not request pin 187
(MX6Q_PAD_NANDF_CS2) from group usdhc2grp on device 20e0000.iomuxc
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On i.MX31 AVIC interrupt controller base address is at 0x68000000.
The problem was shadowed by the AVIC driver, which takes the correct
base address from a SoC specific header file.
Fixes: d2a37b3d91f4 ("ARM i.MX31: Add devicetree support")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add 'gpios' property to pcie1 dt node and populate it with
GPIO3_23 in order to drive PCIE_RESETn high.
This gets PCIe cards to be detected in AM572X IDK board.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The GICv2 CPU interface registers span across 8K, not 4K as indicated in
the DT. Only the GICC_DIR register is located after the initial 4K
boundary, leaving a functional system but without support for separately
EOI'ing and deactivating interrupts.
After this change the system supports split priority drop and interrupt
deactivation.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
[sudeep.holla@arm.com: included same fix for tc1 platform too]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Trying to initialize eMMC slot as SDIO or SD cause failure in n900 port of
qemu. eMMC itself is not detected and is not working.
Real Nokia N900 harware does not have this problem. As eMMC is really not
SDIO or SD based such change is harmless and will fix support for qemu.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 5d080aa30681 ("ARM: dts: dra72: Add separate dtsi for tps65917")
added a separate dtsi for dra72-evm-tps65917 moving all the voltage supplies
to this file. But it missed adding voltage supplies to usb_phy, mmc,
dss and deleted from dra72-evm-common.dtsi. Adding the voltage supply
phandles to these nodes in dra72-evm-tps65917.dtsi
Fixes: 5d080aa30681 ("ARM: dts: dra72: Add separate dtsi for tps65917")
Reported-by: Carlos Hernandez <ceh@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
USB2 port can be operated in dual-role mode but till we
have dual-role support in dwc3 driver let's limit this
port to peripheral mode.
If we don't do so it defaults to host mode. USB1 port
is meant for host only operation and we don't want
both ports in host only mode.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
VBUS detection is available on the board via the palmas PMIC.
Use extcon-palmas driver instead of extcon-gpio-usb driver.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Interrupt numbers are from the datasheet, so no need to keep them in
the ABI. Use the number in the DT file.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Use 'interrupt-names' for getting the charger interrupt number.
Fixes: 1934e89a769b ("ARM: dts: am335x: Add the charger interrupt")
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fixes: ("ab8dd3aed011 ARM: DTS: Add minimal Support for Logic PD
DM3730 SOM-LV")
This adds the dts file into the Makefile. This should have been included in
the original patch.
V2: Update patch description - same source code
V1: Original patch
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 55871eb6e2cc ("ARM: dts: dra7: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 55871eb6e2cc ("ARM: dts: dra7: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 06bfb9c19957 ("ARM: dts: dm816x: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 06bfb9c19957 ("ARM: dts: dm816x: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 76155b378c59 ("ARM: dts: dm814x: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 76155b378c59 ("ARM: dts: dm814x: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 75813028bbd7 ("ARM: dts: am4372: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 75813028bbd7 ("ARM: dts: am4372: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit f8bf01611c99 ("ARM: dts: am33xx: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: f8bf01611c99 ("ARM: dts: am33xx: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 76a8548ea987 ("ARM: dts: omap5: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 76a8548ea987 ("ARM: dts: omap5: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit da6269e7e3dd ("ARM: dts: omap4: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: da6269e7e3dd ("ARM: dts: omap4: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 008a2ebcd677 ("ARM: dts: omap3: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 008a2ebcd677 ("ARM: dts: omap3: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit d1f3156fc8c7 ("ARM: dts: omap2: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: d1f3156fc8c7 ("ARM: dts: omap2: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The SoC hix5hd2 compatible string has the suffix "-gmac" and
we should not change it.
We should only add the generic compatible string "hisi-gmac-v1".
Fixes: 0855950ba580 ("ARM: dts: hix5hd2: add gmac generic compatible and clock names")
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"Lots of changes as usual, so I'm trying to be brief here. Most of the
new hardware support has the respective driver changes merged through
other trees or has had it available for a while, so this is where
things come together.
We get a DT descriptions for a couple of new SoCs, all of them
variants of other chips we already support, and usually coming with a
new evaluation board:
- Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
- Qualcomm MDM9615 LTE baseband
- NXP imx6ull, the latest and smallest i.MX6 application processor variant
- Renesas RZ/G (r8a7743 and r8a7745) application processors
- Rockchip PX3, a variant of the rk3188 chip used in Android tablets
- Rockchip rk1108 single-core application processor
- ST stm32f746 Cortex-M7 based microcontroller
- TI DRA71x automotive processors
These are commercially available consumer platforms we now support:
- Motorola Droid 4 (xt894) mobile phone
- Rikomagic MK808 Android TV stick based on Rockchips rx3066
- Cloud Engines PogoPlug v3 based on OX820
- Various Broadcom based wireless devices:
- Netgear R8500 router
- Tenda AC9 router
- TP-LINK Archer C9 V1
- Luxul XAP-1510 Access point
- Turris Omnia open hardware router based on Armada 385
And a couple of new boards targeted at developers, makers or
industrial integration:
- Macnica Sodia development platform for Altera socfpga (Cyclone V)
- MicroZed board based on Xilinx Zynq FPGA platforms
- TOPEET itop/elite based on exynos4412
- WP8548 MangOH Open Hardware platform for IOT, based on Qualcomm MDM9615
- NextThing CHIP Pro gadget
- NanoPi M1 development board
- AM571x-IDK industrial board based on TI AM5718
- i.MX6SX UDOO Neo
- Boundary Devices Nitrogen6_SOM2 (i.MX6)
- Engicam i.CoreM6
- Grinn i.MX6UL liteSOM/liteBoard
- Toradex Colibri iMX6 module
Other changes:
- added peripherals on renesas, davinci, stm32f429, uniphier, sti,
mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
mvebu, allwinner, broadcom, exynos, zynq
- Continued fixes for W=1 dtc warnings
- The old STiH415/416 SoC support gets removed, these never made it
into products and have served their purpose in the kernel as a
template for teh newer chips from ST
- The exynos4415 dtsi file is removed as nothing uses it.
- Intel PXA25x can now be booted using devicetree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (422 commits)
arm: dts: zynq: Add MicroZed board support
ARM: dts: da850: enable high speed for mmc
ARM: dts: da850: Add node for pullup/pulldown pinconf
ARM: dts: da850: enable memctrl and mstpri nodes per board
ARM: dts: da850-lcdk: Add ethernet0 alias to DT
ARM: dts: artpec: add pcie support
ARM: dts: add support for Turris Omnia
devicetree: Add vendor prefix for CZ.NIC
ARM: dts: berlin2q-marvell-dmp: fix typo in chosen node
ARM: dts: berlin2q-marvell-dmp: fix regulators' name
ARM: dts: Add xo to sdhc clock node on qcom platforms
ARM: dts: r8a7794: Add device node for PRR
ARM: dts: r8a7793: Add device node for PRR
ARM: dts: r8a7792: Add device node for PRR
ARM: dts: r8a7791: Add device node for PRR
ARM: dts: r8a7790: Add device node for PRR
ARM: dts: r8a7779: Add device node for PRR
ARM: dts: r8a73a4: Add device node for PRR
ARM: dts: sk-rzg1e: add Ether support
ARM: dts: sk-rzg1e: initial device tree
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-urgent fixes from Arnd Bergmann:
"As usual, we queue up a few fixes that don't seem urgent enough to go
in through -rc, or that just came a little too late given their size.
The zx fixes make the platform finally boot on real hardware, the
davinci and imx31 get the DT support working better for some of the
machines that are still normally used with classic board files. One
tegra fix is important for new bootloader versions, but the bug has
been around for a while without anyone noticing.
The other changes are mostly cosmetic"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (22 commits)
arm64: tegra: Add missing Smaug revision
arm64: tegra: Add VDD_GPU regulator to Jetson TX1
arm64: dts: zte: clean up gic-v3 redistributor properties
arm64: dts: zx: Fix gic GICR property
bus: vexpress-config: fix device reference leak
soc: ti: qmss: fix the case when !SMP
ARM: lpc32xx: drop duplicate header device.h
ARM: ixp4xx: drop duplicate header gpio.h
ARM: socfpga: fix spelling mistake in error message
ARM: dts: imx6q-cm-fx6: fix fec pinctrl
ARM: dts: imx7d-pinfunc: fix UART pinmux defines
ARM: dts: imx6qp: correct LDB clock inputs
ARM: OMAP2+: pm-debug: Use seq_putc() in two functions
ARM: OMAP2+: Remove the omapdss_early_init_of() function
mfd: tps65217: Fix mismatched interrupt number
ARM: zx: Fix error handling
ARM: spear: Fix error handling
ARM: davinci: da850: Fix pwm name matching
ARM: clk: imx31: properly init clocks for machines with DT
clk: imx31: fix rewritten input argument of mx31_clocks_init()
...
|
|
Pull dmaengine updates from Vinod Koul:
"Fairly routine update this time around with all changes specific to
drivers:
- New driver for STMicroelectronics FDMA
- Memory-to-memory transfers on dw dmac
- Support for slave maps on pl08x devices
- Bunch of driver fixes to use dma_pool_zalloc
- Bunch of compile and warning fixes spread across drivers"
[ The ST FDMA driver already came in earlier through the remoteproc tree ]
* tag 'dmaengine-4.10-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (68 commits)
dmaengine: sirf-dma: remove unused ‘sdesc’
dmaengine: pl330: remove unused ‘regs’
dmaengine: s3c24xx: remove unused ‘cdata’
dmaengine: stm32-dma: remove unused ‘src_addr’
dmaengine: stm32-dma: remove unused ‘dst_addr’
dmaengine: stm32-dma: remove unused ‘sfcr’
dmaengine: pch_dma: remove unused ‘cookie’
dmaengine: mic_x100_dma: remove unused ‘data’
dmaengine: img-mdc: remove unused ‘prev_phys’
dmaengine: usb-dmac: remove unused ‘uchan’
dmaengine: ioat: remove unused ‘res’
dmaengine: ioat: remove unused ‘ioat_dma’
dmaengine: ioat: remove unused ‘is_raid_device’
dmaengine: pl330: do not generate unaligned access
dmaengine: k3dma: move to dma_pool_zalloc
dmaengine: at_hdmac: move to dma_pool_zalloc
dmaengine: at_xdmac: don't restore unsaved status
dmaengine: ioat: set error code on failures
dmaengine: ioat: set error code on failures
dmaengine: DW DMAC: add multi-block property to device tree
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here's the big set of USB/PHY patches for 4.10-rc1.
A number of new drivers are here in this set of changes. We have a new
USB controller type "mtu3", a new usb-serial driver, and the usual
churn in the gadget subsystem and the xhci host controller driver,
along with a few other new small drivers added. And lots of little
other changes all over the USB and PHY driver tree. Full details are
in the shortlog
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (309 commits)
USB: serial: option: add dlink dwm-158
USB: serial: option: add support for Telit LE922A PIDs 0x1040, 0x1041
USB: OHCI: nxp: fix code warnings
USB: OHCI: nxp: remove useless extern declaration
USB: OHCI: at91: remove useless extern declaration
usb: misc: rio500: fix result type for error message
usb: mtu3: fix U3 port link issue
usb: mtu3: enable auto switch from U3 to U2
usbip: fix warning in vhci_hcd_probe/lockdep_init_map
usb: core: usbport: Use proper LED API to fix potential crash
usbip: add missing compile time generated files to .gitignore
usb: hcd.h: construct hub class request constants from simpler constants
USB: OHCI: ohci-pxa27x: remove useless functions
USB: OHCI: omap: remove useless extern declaration
USB: OHCI: ohci-omap: remove useless functions
USB: OHCI: ohci-s3c2410: remove useless functions
USB: cdc-acm: add device id for GW Instek AFG-125
fsl/usb: Workarourd for USB erratum-A005697
usb: hub: Wait for connection to be reestablished after port reset
usbip: vudc: Refactor init_vudc_hw() to be more obvious
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This is a fairly quiet release. We don't have any patches to the core
framework. The only patch that can even be considered "core" adds
another clk_get() variant. The rest of the changes are in drivers for
various SoCs, and we have a few bits for ARM shmobile architecture
code (dts and mach) due to the dependency we're breaking between
shmobile architecture code and its clk driver. Those shmobile bits
have also been pulled into arm-soc tree. Here's the summary:
Core:
- Support for devm_get_clk_from_child() used with DT bindings that
have subnodes with the 'clocks' property
New Drivers:
- Allwinner A64 (sun50i)
- i.MX imx6ull
- Socionext's UniPhier SoC CPUs
- Mediatek MT2701 SoCs
- Rockchip rk1108 SoCs
- Qualcomm MSM8994/MSM8992 SoCS
- Qualcomm RPM Clocks
- Hisilicon Hi3516CV300 and Hi3798CV200 CRG
- Oxford Semiconductor OX820 and OX810SE SoCs
- Renesas RZ/G1M and RZ/GIE SoCs
- Renesas R-Car RST driver for mode pin states
Updates:
- Four Allwinner SoCs are migrated to the new style clk driver
- Rockchip rk3399,rk3066 PLL optimizations
- i.MX LVDS display glitch fixes and AV PLL precision improvements
- Qualcomm MSM8996 GPU GDSCs, hw controlled GDSCs, and Alpha PLL
support
- Explicit demodularization of always builtin drivers
- Freescale Qoriq ls1012a and ls1046a support
- Exynos 5433 parent typo fix and critical clock tagging
- Renesas r8a7743/r8a7745 CPG
- Renesas R-Car M3-W CSI2/VIN/SYS-DMAC/(H)SCIF/I2C/DRIF/gfx support
- stm32f4* LSI, LSE, RTC, and QSPI clocks
- pxa27x and pxa25x cpufreq as clks
- TI omap36xx sprz319 advisory 2.1 workaround
- Broadcom bcm2835 rate change propogation to PLLH_AUX from VEC"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (150 commits)
clk: bcm: Fix 'maybe-uninitialized' warning in bcm2835_clock_choose_div_and_prate()
clk: add devm_get_clk_from_child() API
clk: st: clk-flexgen: Unmap region obtained by of_iomap
clk: keystone: pll: Unmap region obtained by of_iomap
clk:mmp:clk-of-mmp2: Free memory and Unmap region obtained by kzalloc and of_iomap
clk:mmp:clk-of-pxa910: Free memory and Unmap region obtained by kzmalloc and of_iomap
clk: mmp: clk-of-pxa1928: Free memory obtained by kzalloc
clk: cdce925: Fix limit check
clk: bcm: Make COMMON_CLK_IPROC into a library
clk: qoriq: added ls1012a clock configuration
clk: ti: dra7: fix "failed to lookup clock node gmac_gmii_ref_clk_div" boot message
clk: bcm: Allow rate change propagation to PLLH_AUX on VEC clock
clk: bcm: Support rate change propagation on bcm2835 clocks
clk: bcm2835: Avoid overwriting the div info when disabling a pll_div clk
clk: ti: omap36xx: Work around sprz319 advisory 2.1
clk: clk-wm831x: fix a logic error
clk: uniphier: add cpufreq data for LD11, LD20 SoCs
clk: uniphier: add CPU-gear change (cpufreq) support
clk: qcom: Put venus core0/1 gdscs to hw control mode
clk: qcom: gdsc: Add support for gdscs with HW control
...
|
|
|
|
Bug report from Debian [0] shows there's minor changed model of
Linkstation LS-GL that uses the 2nd SATA port of the SoC.
So it's necessary to enable two SATA ports, though for that specific
model only the 2nd one is used.
[0] https://bugs.debian.org/845611
Fixes: b1742ffa9ddb ("ARM: dts: orion5x: add device tree for buffalo linkstation ls-gl")
Reported-by: Ryan Tandy <ryan@nardis.ca>
Tested-by: Ryan Tandy <ryan@nardis.ca>
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The eLCDIF IP of the i.MX 7 SoC knows multiple clocks and lists them
separately:
Clock Clock Root Description
apb_clk MAIN_AXI_CLK_ROOT AXI clock
pix_clk LCDIF_PIXEL_CLK_ROOT Pixel clock
ipg_clk_s MAIN_AXI_CLK_ROOT Peripheral access clock
All of them are switched by a single gate, which is part of the
IMX7D_LCDIF_PIXEL_ROOT_CLK clock. Hence using that clock also for
the AXI bus clock (clock-name "axi") makes sure the gate gets
enabled when accessing registers.
There seem to be no separate AXI display clock, and the clock is
optional. Hence remove the dummy clock.
This fixes kernel freezes when starting the X-Server (which
disables/re-enables the display controller).
Fixes: e8ed73f691bd ("ARM: dts: imx7d: add lcdif support")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
In a previous commit, I made a copy/paste error in the pinmux
definitions of UART3: PG{13,14} instead of PA{13,14}. This commit takes
care of that. I have tested this commit on Orange Pi PC and Orange Pi
Plus, and it works for these boards.
Fixes: e3d11d3c45c5 ("dts: sun8i-h3: add pinmux definitions for
UART2-3")
Signed-off-by: Jorik Jonker <jorik@kippendief.biz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
next/dt
arm: Xilinx Zynq dt patches for v4.10
- Remove skeleton.dtsi
- Fix DTC warnings
- Coding style changes
- Microzed support
* tag 'zynq-dt-for-4.10' of https://github.com/Xilinx/linux-xlnx:
arm: dts: zynq: Add MicroZed board support
ARM: zynq: Fix pmu register description coding style
ARM: zynq: Fix W=1 dtc 1.4 warnings
ARM: zynq: Remove skeleton.dtsi
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt
- Add device tree nodes for pin pull-up/pull-down
bias control on DA850.
- Enable high speed support on DA850 MMC/SD
* tag 'davinci-for-v4.10/dt-4' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850: enable high speed for mmc
ARM: dts: da850: Add node for pullup/pulldown pinconf
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add gmac generic compatible and clock names.
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added basic dts support for MicroZed board.
- UART
- SDHCI
- Ethernet
Cc: Soren Brinkmann <soren.brinkmann@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
The mmc controller in da850 supports high speed modes
so add cap-sd-highspeed and cap-mmc-highspeed.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This SoC has a separate pin controller for configuring pullup/pulldown
bias on groups of pins.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "omap dts changes for v4.10, part 2" from Tony Lindgren:
Second set of device tree changes for omaps for v4.10 merge window:
- Fix up new instances of gpio-key,wakeup to use wakeup-source
- Add beaglebone LCDC blue-and-red-wiring property to make use
of the new driver features
- Add bindings for IIO support for am335x and am437x
- Add palmas PMIC overide powerhold property for am57xx
- Update am335x-baltos to use phy-handle property
- Add initial support for am571x-idk
* tag 'omap-for-v4.10/dt-late-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: AM571x-IDK Initial Support
ARM: dts: am335x-baltos: use phy-phandle declarations
ARM: dts: am57xx-idk-common: Add overide powerhold property
ARM: dts: am57xx-beagle-x15-common: Add overide powerhold property
ARM: dts: am57xx-idk: Add Industrial output support
ARM: dts: am57xx-idk: Add Industrial input support
ARM: dts: am437x-idk: Add Industrial output support
ARM: dts: am437x-idk: Add Industrial input support
ARM: dts: am335x-icev2: Add ADC support
ARM: dts: am335x-icev2: Disable Industrial I/O LEDs and fix naming
ARM: dts: am335x-icev2: Add Industrial input support
ARM: dts: am335x-boneblack: Add blue-and-red-wiring -property to LCDC node
ARM: dts: omap5: replace gpio-key,wakeup with wakeup-source property
|
|
Pull "mvebu dt for 4.10 (part 1)" from Gregory CLEMENT:
Add Turris Omnia support, an open hardware router Armada 385 based
* tag 'mvebu-dt-4.10-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: add support for Turris Omnia
devicetree: Add vendor prefix for CZ.NIC
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jszhang/linux-berlin into next/dt
Pull "Berlin DT changes for v4.10" from Jisheng Zhang:
- fix DTC compiler warning
- fix typo in chosen node
* tag 'berlin-dt-for-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jszhang/linux-berlin:
ARM: dts: berlin2q-marvell-dmp: fix typo in chosen node
ARM: dts: berlin2q-marvell-dmp: fix regulators' name
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "Rockchip dts32 changes for 4.10" from Heiko Stübner:
A bit of attention for the rk3066, fixed tsadc reset node
as well as enabling the dma for uart and mmc controllers.
And one new soc, the rk1108 combining a single-core Cortex-A7
with a separate DSP core.
* tag 'v4.10-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add the sdmmc pinctrl for rk1108
ARM: dts: rockchip: add rockchip RK1108 Evaluation board
ARM: dts: rockchip: add basic support for RK1108 SOC
clk: rockchip: add dt-binding header for rk1108
dt-bindings: rockchip-dw-mshc: add RK1108 dw-mshc description
ARM: dts: rockchip: enable dma for uart and mmc on rk3066a
ARM: dts: rockchip: fix TSADC reset node for rk3066a
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt
Pull "Qualcomm Device Tree Changes for v4.10 - Part 2" from Andy Gross:
* Add SDHC xo clk
* tag 'qcom-dts-for-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
ARM: dts: Add xo to sdhc clock node on qcom platforms
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Pull "Samsung DeviceTree second update for v4.10" from Krzysztof Kozłowski:
1. Cleanups in MSHC nodes.
2. Enable ADC on Odroid boards.
3. Fix interrupt flags on recently added DMA sound nodes in Exynos5410.
* tag 'samsung-dt-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Remove the cd-gpios property for eMMC of Odroid XU3/4
ARM: dts: exynos: Specify snps, dwmac in compatible string for gmac
ARM: dts: exynos: Fix invalid GIC interrupt flags in audio block of Exynos5410
ARM: dts: exynos: Add ADCs on 4412 and 5422 based odroid boards.
ARM: dts: exynos: Replace "clock-freq-min-max" with "max-frequency"
|
|
http://github.com/Broadcom/stblinux into next/dt
Pull "Broadcom devicetree changes for 4.10" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoC Device Tree changes for 4.10,
please pull the following:
- Rafal adds support for the Netgear R8500 routers, adds basic support
for the Tenda AC9 router which uses the new BCM53573 SoC (single core Cortex
A7). He also enables the UART on the Netgear R8000 and restructures the
include files a bit for the BCM47094 SoC, finally he adds USB 3.0 PHY nodes
which enables USB 3.0 on BCM5301X devices that support it. Finally he adds
support for the TP-LINK Archer C9 V1 router.
- Kamal adds support for the QSPI controller on the Northstar Plus SoCs and updates
the bcm958625k reference board to have it enabled
- Dan adds support for the Luxul XAP-1510 (using a BCM4708) and XWR-3100 (using
a BCM47094)
- Scott fixes the pinctrl names in the Cygnus DTS files
- Jonathan enables the Broadcom iProc mailbox controller for Broadcom Cygnus/iProc
SoCs, he adds interrupt support for the GPIO CRMU hardware block and finally adds
the node for the OTP controller found on Cygnus SoCs
- Dhananjay enables the GPIO B controller on Norstarh Plus SoCs
- Eric defines standard pinctrl groups in the BCM2835 GPIO node
- Gerd adds definitions for the pinctrl groups and updates the PWM, I2C and SDHCI nodes
to use their appropriate pinctrl functions
- Linus adds names for the Raspberry Pi GPIO lines based on the datasheet
- Martin adds the DT binding and nodes for the Raspberry Pi firmware thermal block
- Stefan fixes a few typos with respect to the BCM2835 mailbox binding example and
Device Tree nodes he also fixes the Raspberry Pi GPIO lines names and finally
adds names for the Raspberry Zero GPIO lines
* tag 'arm-soc/for-4.10/devicetree' of http://github.com/Broadcom/stblinux: (29 commits)
ARM: bcm2835: Add names for the RPi Zero GPIO lines
ARM: bcm2835: Fix names for the Raspberry Pi GPIO lines
ARM: dts: enable GPIO-b for Broadcom NSP
ARM: BCM5301X: Add DT for TP-LINK Archer C9 V1
ARM: dts: Add node for Broadcom OTP controller driver
ARM: dts: Enable interrupt support for cygnus crmu gpio driver
ARM: dts: Enable Broadcom iProc mailbox controller
ARM: bcm2835: Add names for the Raspberry Pi GPIO lines
ARM: bcm2835: dts: add thermal node to device-tree of bcm283x
dt: bindings: add thermal device driver for bcm2835
ARM: dts: bcm283x: fix typo in mailbox address
DT: binding: bcm2835-mbox: fix address typo in example
ARM: dts: cygnus: fix naming of pinctrl node
ARM: BCM53573: Specify PMU and its ILP clock in the DT
ARM: BCM5301X: Add DT for Luxul XWR-3100
ARM: BCM5301X: Add DT for Luxul XAP-1510
ARM: BCM5301X: Specify USB 3.0 PHY in DT
ARM: BCM5301X: Enable UART on Netgear R8000
ARM: BCM5301X: Add separated DTS include file for BCM47094
ARM: dts: NSP: Add QSPI nodes to NSPI and bcm958625k DTSes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt
Merge "SoCFPGA DTS update for v4.10, part 3" from Dinh Nguyen:
- Fine tune L2 cache configuration
* tag 'socfpga_dts_for_v4.10_part_3' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: socfpga: fine-tune L2 cache configuration
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Second Round of Renesas ARM Based SoC DT Updates for v4.10" from Simon Horman:
Enhancements:
* Add device nodes for PRR
* Add r8a7745 SoC and sk-rzg1e board
* Add r8a7743 SoC and sk-rzg1m board
* Enable SDR-104 and I2C demuxer on alt, koelsch and lager boards
Corrections:
* Use SYSC "always-on" PM Domain for sound on r8a7794 SoC
* Correct hsusb parent clock on r8a7794 SoC
* Correct PFC names for DU on alt board
* tag 'renesas-dt2-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (33 commits)
ARM: dts: r8a7794: Add device node for PRR
ARM: dts: r8a7793: Add device node for PRR
ARM: dts: r8a7792: Add device node for PRR
ARM: dts: r8a7791: Add device node for PRR
ARM: dts: r8a7790: Add device node for PRR
ARM: dts: r8a7779: Add device node for PRR
ARM: dts: r8a73a4: Add device node for PRR
ARM: dts: sk-rzg1e: add Ether support
ARM: dts: sk-rzg1e: initial device tree
ARM: dts: r8a7745: add IRQC support
ARM: dts: r8a7745: add Ether support
ARM: dts: r8a7745: add [H]SCIF{|A|B} support
ARM: dts: r8a7745: add SYS-DMAC support
ARM: dts: r8a7745: initial SoC device tree
ARM: dts: sk-rzg1m: add Ether support
ARM: dts: sk-rzg1m: initial device tree
ARM: dts: r8a7743: add IRQC support
ARM: dts: r8a7743: add Ether support
ARM: dts: r8a7743: add [H]SCIF{A|B} support
ARM: dts: r8a7743: add SYS-DMAC support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt
Pull "DaVinci DT updates for v4.10 (part 3)" from Sekhar Nori:
Some fixes for device-tree patches already queued.
- Fix SD card detect polarity
- Prevent Ethernet from picking a random mac address
- Fix error messages on platforms which dont use
bus master and emif priority settings.
* tag 'davinci-for-v4.10/dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850: enable memctrl and mstpri nodes per board
ARM: dts: da850-lcdk: Add ethernet0 alias to DT
ARM: dts: da850-lcdk: fix mmc card detect polarity
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt
Pull "DaVinci DT updates for v4.10 (part 2)" from Sekhar Nori:
Adds device tree nodes enabling DDR controller
and bus master priority settings needed for
stable LCDC operation on DA850.
Also adds support for MUSB device on DA850
providing USB OTG support.
* tag 'davinci-for-v4.10/dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850-lcdk: Enable the usb otg device node
ARM: dts: da850: Add the usb otg device node
ARM: dts: da850: add the mstpri and ddrctl nodes
|
|
Several versions of DW DMAC have multi block transfers hardware
support. Hardware support of multi block transfers is disabled
by default if we use DT to configure DMAC and software emulation
of multi block transfers used instead.
Add multi-block property, so it is possible to enable hardware
multi block transfers (if present) via DT.
Switch from per device is_nollp variable to multi_block array
to be able enable/disable multi block transfers separately per
channel.
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Currently the memory controller and master priorities drivers are
enabled in da850.dtsi. For boards for which there are no settings
defined, this makes these drivers emit error messages.
Disable the nodes in da850.dtsi and only enable them for da850-lcdk -
the only board that currently needs them.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
