| Age | Commit message (Collapse) | Author |
|---|
|
https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
6.14, please pull the following:
- Chester fixes the switch port assignments on the ASUS RT-AC3200 and
RT-AC5300 routers
- Phil removes a Device Tree property flagging the BCM2711 ARM timers as
not being configured which would have prevented the use of vDSO on the
Pi 4 running a 32-bit kernel
* tag 'arm-soc/for-6.14/devicetree-fixes-part2' of https://github.com/Broadcom/stblinux:
ARM: dts: BCM5301X: Fix switch port labels of ASUS RT-AC3200
ARM: dts: BCM5301X: Fix switch port labels of ASUS RT-AC5300
ARM: dts: bcm2711: Don't mark timer regs unconfigured
Link: https://lore.kernel.org/r/20250308150528.1900822-1-florian.fainelli@broadcom.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
After using the device for a while, Tom reports that he initially described
the switch port labels incorrectly. Apparently, ASUS's own firmware also
describes them incorrectly. Correct them to what is seen on the chassis.
Reported-by: Tom Brautaset <tbrautaset@gmail.com>
Fixes: b116239094d8 ("ARM: dts: BCM5301X: Add DT for ASUS RT-AC3200")
Signed-off-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://lore.kernel.org/r/20250304-for-broadcom-fix-rt-ac3200-switch-ports-v1-1-7e249a19a13e@arinc9.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
|
|
After using the device for a while, Tom reports that he initially described
the switch port labels incorrectly. Correct them.
Reported-by: Tom Brautaset <tbrautaset@gmail.com>
Fixes: 961dedc6b4e4 ("ARM: dts: BCM5301X: Add DT for ASUS RT-AC5300")
Signed-off-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://lore.kernel.org/r/20250303-for-broadcom-fix-rt-ac5300-switch-ports-v1-1-e058856ef4d3@arinc9.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
|
|
During upstream process of Raspberry Pi 4 back in 2019 the ARMv7 stubs
didn't configured the ARM architectural timer. This firmware issue has
been fixed in 2020, which gave users enough time to update their system.
So drop this property to allow the use of the vDSO version of
clock_gettime.
Link: https://github.com/raspberrypi/tools/pull/113
Fixes: 7dbe8c62ceeb ("ARM: dts: Add minimal Raspberry Pi 4 support")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250222094113.48198-1-wahrenst@gmx.net
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 6.14:
- A tqma8mpql board fix from Alexander Stein to correct vqmmc-supply for
usdhc3
- A change from Joe Hattori to fix OF node leak in imx-scu driver probe
- A soc-imx8m driver fix from Peng Fan unregister cpufreq and soc device
in cleanup path
- A couple of changes from Stefan Eichenberger to fix iMX6 Apalis
poweroff and iMX8M verdin-dahlia sound-card descriptions
* tag 'imx-fixes-6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: freescale: imx8mm-verdin-dahlia: add Microphone Jack to sound card
arm64: dts: freescale: imx8mp-verdin-dahlia: add Microphone Jack to sound card
soc: imx8m: Unregister cpufreq and soc dev in cleanup path
ARM: dts: imx6qdl-apalis: Fix poweroff on Apalis iMX6
arm64: dts: freescale: tqma8mpql: Fix vqmmc-supply
firmware: imx-scu: fix OF node leak in .probe()
Link: https://lore.kernel.org/r/Z8A+rihFV4K3l8QR@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The ARM PL011 UART instances in BCM2711 are r1p5 spec, which means they
have 32-entry FIFOs. The correct periphid value for this is 0x00341011.
Thanks to N Buchwitz for pointing this out.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20250223125614.3592-2-wahrenst@gmx.net
Fixes: 7dbe8c62ceeb ("ARM: dts: Add minimal Raspberry Pi 4 support")
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
|
|
During s2idle tests on the Raspberry CM4 the VPU firmware always crashes
on xHCI power-domain resume:
root@raspberrypi:/sys/power# echo freeze > state
[ 70.724347] xhci_suspend finished
[ 70.727730] xhci_plat_suspend finished
[ 70.755624] bcm2835-power bcm2835-power: Power grafx off
[ 70.761127] USB: Set power to 0
[ 74.653040] USB: Failed to set power to 1 (-110)
This seems to be caused because of the mixed usage of
raspberrypi-power and bcm2835-power at the same time. So avoid
the usage of the VPU firmware power-domain driver, which
prevents the VPU crash.
Fixes: 522c35e08b53 ("ARM: dts: bcm2711: Add BCM2711 xHCI support")
Link: https://github.com/raspberrypi/linux/issues/6537
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20250201112729.31509-1-wahrenst@gmx.net
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
|
|
The current solution for powering off the Apalis iMX6 is not functioning
as intended. To resolve this, it is necessary to power off the
vgen2_reg, which will also set the POWER_ENABLE_MOCI signal to a low
state. This ensures the carrier board is properly informed to initiate
its power-off sequence.
The new solution uses the regulator-poweroff driver, which will power
off the regulator during a system shutdown.
Cc: <stable@vger.kernel.org>
Fixes: 4eb56e26f92e ("ARM: dts: imx6q-apalis: Command pmic to standby for poweroff")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Pull SoC devicetree updates from Arnd Bergmann:
"We see the addition of eleven new SoCs, including a total of sixx
arm64 chips from Qualcomm alone. Overall, the Qualcomm platforms once
again make up the majority of all changes, after a couple of quieter
releases.
The new SoCs in this branch are:
- Microchip sama7d65 is a new 32-bit embedded chip with a single
Cortex-A7 and the current high end of the old Atmel SoC line.
- Samsung Exynos 9810 is a mobile phone chip used in some older
phones like the Samsung Galaxy S9
- Renesas R-Car V4H ES3.0 (R8A779G3) is an updated version of the V4H
(R8A779G0) low-power automotive SoC
- Renesas RZ/G3E (R0A09G047) is a family of embedded chips using
Cortex-A55 cores
- Qualcomm Snapdragon 8 Elite (SM8750) is a new phone chip based on
Qualcomm's Oryon CPU cores.
- Qualcomm Snapdragon AR2 (SAR2130P) is a SoC for augmented reality
glasses.
- Qualcomm IQ6 (QCS610) and IQ8 (QCS8300) are two industrial IOT
platforms.
- Snapdragon 425 (MSM8917) is a mobile phone SoC from 2016
- Qualcomm IPQ5424 is a Wi-Fi 7 networking chip
All of the above are part of already supported SoC families that only
need new devicetree files. Two additional SoCs in new families are
part of a separate branch.
There are 48 new machines in total, including six arm32 ones based on
aspeed. broadcom, microchip and st SoCs all using Cortex-A7 cores, and
a single risc-v board, the Banana Pi R3.
The remaining ones use arm64 chips from Broadcom, Samsung, NXP,
Mediatek, Qualcomm, Renesas and Rockchips and cover development
boards, phones, laptops, industrial machines routers.
A lot of ongoing work is for cleaning up build time warnings and other
issues, in addition to the new machines and added features"
* tag 'soc-dt-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (619 commits)
arm64: tegra: Fix Tegra234 PCIe interrupt-map
arm64: dts: qcom: x1e80100-romulus: Update firmware nodes
arm64: dts: rockchip: add DTs for Firefly ITX-3588J and its Core-3588J SoM
dt-bindings: arm: rockchip: Add Firefly ITX-3588J board
arm64: dts: rockchip: Add Orange Pi 5 Max board
dt-bindings: arm: rockchip: Add Xunlong Orange Pi 5 Max
arm64: dts: rockchip: refactor common rk3588-orangepi-5.dtsi
arm64: dts: rockchip: add WLAN to rk3588-evb1 controller
arm64: dts: rockchip: increase gmac rx_delay on rk3399-puma
arm64: dts: rockchip: Delete redundant RK3328 GMAC stability fixes
arm64: tegra: Disable Tegra234 sce-fabric node
arm64: tegra: Fix typo in Tegra234 dce-fabric compatible
arm64: tegra: Fix DMA ID for SPI2
arm64: dts: qcom: msm8916-samsung-serranove: Add display panel
arm64: dts: qcom: sm8650: Add 'global' interrupt to the PCIe RC nodes
arm64: dts: qcom: sm8550: Add 'global' interrupt to the PCIe RC nodes
arm64: dts: qcom: Remove unused and undocumented properties
arm64: dts: qcom: sdm450-lenovo-tbx605f: add DSI panel nodes
arm64: dts: qcom: pmi8950: add LAB-IBB nodes
arm64: dts: qcom: ipq5424: enable the download mode support
...
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/joel/bmc into soc/dt
ASPEED device tree updates for 6.14
- New machines
* IBM SPB1 AST2600 BMC machine, a Sapphire Rapids x86 server
* Ampre Mt Jefferson AST2600 BMC
- Updates to mtmitchell, rainier, blueridge, everest, fuji, system1,
harma, catalina and minerva
- A big rework of yosemite4
* tag 'aspeed-6.14-devicetree' of https://git.kernel.org/pub/scm/linux/kernel/git/joel/bmc: (55 commits)
ARM: dts: aspeed: yosemite4: adjust secondary flash name
ARM: dts: aspeed: system1: Use crps PSU driver
ARM: dts: aspeed: minerva: add second source RTC
ARM: dts: aspeed: minerva: add bmc ready led setting
ARM: dts: aspeed: minerva: add i/o expanders on each FCB
ARM: dts: aspeed: minerva: add i/o expanders on bus 0
ARM: dts: aspeed: catalina: remove interrupt of GPIOB4 form all IOEXP
ARM: dts: aspeed: catalina: revise ltc4287 shunt-resistor value
arm: dts: aspeed: Blueridge and Rainer: Add VRM presence GPIOs
ARM: dts: aspeed: Blueridge and Fuji: Fix LED node names
arm: dts: aspeed: Everest and Fuji: Add VRM presence gpio expander
ARM: dts: aspeed: sbp1: IBM sbp1 BMC board
dt-bindings: arm: aspeed: add IBM SBP1 board
ARM: dts: aspeed: Add device tree for Ampere's Mt. Jefferson BMC
dt-bindings: arm: aspeed: add Mt. Jefferson board
ARM: dts: aspeed: yosemite4: Add i2c-mux for ADC monitor on Spider Board
ARM: dts: aspeed: yosemite4: Revise adc128d818 adc mode on Fan Boards
ARM: dts: aspeed: yosemite4: Change the address of Fan IC on fan boards
ARM: dts: aspeed: yosemite4: Revise address of i2c-mux for two fan boards
ARM: dts: aspeed: yosemite4: correct the compatible string for max31790
...
Link: https://lore.kernel.org/r/CACPK8Xe8yZLXzEQPp=1D2f0TsKA7hBZG=pHHW6U51FMpp_BiRQ@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/dt
Qualcomm Arm32 DeviceTree updates for v6.14
Describe the interconnect paths for PCIe EP controllers on SDX55 and
SDX65. Disable USB U1/U2 entry to improve USB stability on the same.
* tag 'qcom-arm32-for-6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: sdx55: Disable USB U1/U2 entry
ARM: dts: qcom: sdx65: Disable USB U1/U2 entry
ARM: dts: qcom: sdx55: Add CPU PCIe EP interconnect path
ARM: dts: qcom: sdx65: Add PCIe EP interconnect path
Link: https://lore.kernel.org/r/20250111171126.369502-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into soc/dt
ARM: tegra: Device tree fixes for v6.14-rc1
This contains a fix that makes sure the power to the USB ports is
maintained during boot. This helps with booting from USB storage.
* tag 'tegra-for-6.14-arm-dt' of https://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: nyan: Maintain power to USB ports on boot
Link: https://lore.kernel.org/r/20250110185355.4143505-2-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://github.com/Broadcom/stblinux into soc/dt
This pull request contains Broadcom ARM-based SoCs Device Tree updates
for 6.14, please pull the following:
- Rob removes some unused and undocumented properties pertaining to the
SPI flash controller on Broadcom boards
- Linus adds a number of BCM6846 peripherals: HWRNG, watchdog, GPIO,
MDIO, LED controller, DMA and then proceeds with adding support for
the GEnexsis XG6846B PON router
- Rosen sets the MAC address NVMEM reference on the Meraki MR26 platform
* tag 'arm-soc/for-6.14/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: meraki-mr26: set mac address for gmac0
ARM: dts: broadcom: Add Genexis XG6846B DTS file
dt-bindings: arm: bcmbca: Add Genexis XG6846B
dt-bindings: vendor-prefixes: Add Genexis
ARM: dts: bcm6846: Add ARM PL081 DMA block
ARM: dts: bcm6846: Add LED controller
ARM: dts: bcm6846: Add MDIO control block
ARM: dts: bcm6846: Add GPIO blocks
ARM: dts: bcm6846: Enable watchdog
ARM: dts: bcm6846: Add iproc rng
arm: dts: broadcom: Remove unused and undocumented properties
Link: https://lore.kernel.org/r/20250109224756.3632025-1-florian.fainelli@broadcom.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into soc/dt
Microchip AT91 device tree updates for v6.14 #2
This update includes:
- device tree files for the SAMA7D65 SoC and its evaluation board
* tag 'at91-dt-6.14-2' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: microchip: add support for sama7d65_curiosity board
ARM: dts: microchip: add sama7d65 SoC DT
Link: https://lore.kernel.org/r/20250109164317.1154613-1-claudiu.beznea@tuxon.dev
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into soc/dt
Allwinner Device Tree changes for 6.14
- Add support for DMA engine and audio codec on F1C100s
and enable audio codec on Lichee Pi Nano
- Add syscon and SRAM nodes for A100
- Enable CPU DVFS for Tanix TX1
- Explicitly configure TCON0 pixel clock parent according to display
output used
This includes one commit shared with the clock tree
dt-bindings: clock: sunxi: Export PLL_VIDEO_2X and PLL_MIPI
which adds the macros for the TCON0 pixel clock parents.
* tag 'sunxi-dt-for-6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: a64: explicitly assign clock parent for TCON0
dt-bindings: clock: sunxi: Export PLL_VIDEO_2X and PLL_MIPI
arm64: dts: allwinner: h313: enable DVFS for Tanix TX1
arm64: dts: allwinner: a100: Add syscon nodes
dt-bindings: sram: sunxi-sram: Add A100 compatible
ARM: dts: suniv: f1c100s: Activate Audio Codec for Lichee Pi Nano
ARM: dts: suniv: f1c100s: Add support for Audio Codec
ARM: dts: suniv: f1c100s: Add support for DMA
Link: https://lore.kernel.org/r/Z36h2FwUxro8rouO@wens.tw
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mediatek/linux into soc/dt
mt7623: fix validation error of ir-receiver
* tag 'mtk-dts32-for-v6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/mediatek/linux:
ARM: dts: mediatek: mt7623: fix IR nodename
Link: https://lore.kernel.org/r/ea93d0ea-a1a0-4d36-8880-4f05c85f0c1b@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap into soc/dt
ARM: dts: ti/omap/dra7: minor updates for v6.14
* tag 'omap-for-v6.14/dt-signed' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap:
ARM: dts: ti/omap: omap3-gta04: use proper touchscreen properties
ARM: dts: ti: am437x-l4: remove autoidle for UART
ARM: dts: ti/omap: gta04: fix pm issues caused by spi module
ARM: dts: dra7: Add bus_dma_limit for l4 cfg bus
Link: https://lore.kernel.org/r/7hmsg2b42q.fsf@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into soc/dt
Microchip AT91 device tree updates for v6.14
This update includes:
- power monitor support for the SAM9X75 Curiosity board (using the PAC1934
device)
- fix the VDDSDMMC rail to 3.3V to avoid breaking USB (for SAMA5D27 WLSOM1
EK and SAMA5D29 Curiosity boards)
- partial support for the SAMA7D65 SoC
- cleanups
* tag 'at91-dt-6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: microchip: sam9x7: Add address/size to spi-controller nodes
ARM: dts: microchip: sam9x60: Add address/size to spi-controller nodes
ARM: dts: microchip: sama5d27_wlsom1_ek: Add no-1-8-v property to sdmmc0 node
ARM: dts: microchip: sama5d29_curiosity: Add no-1-8-v property to sdmmc0 node
ARM: dts: at91: Add sama7d65 pinmux
dt-bindings: atmel-sysreg: add sama7d65 RAM and PIT
dt-bindings: ARM: at91: Document Microchip SAMA7D65 Curiosity
ARM: dts: microchip: sam9x75_curiosity: Add power monitor support
ARM: dts: microchip: sam9x7: Move i2c address/size to dtsi
Link: https://lore.kernel.org/r/20250107081424.758980-2-claudiu.beznea@tuxon.dev
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux into soc/dt
Amlogic ARM DT changes for v6.14:
- remove size and address cells from USB nodes
* tag 'amlogic-arm-dt-for-v6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux:
ARM: dts: amlogic: meson: remove size and address cells from USB nodes
Link: https://lore.kernel.org/r/77c645b3-0cdf-49f4-84e9-11c74074b9a8@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into soc/dt
Add and enable MALI400 support for STiH410-b2260
* tag 'sti-dt-for-v6.14-round1' of https://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: dts: st: enable the MALI gpu on the stih410-b2260
ARM: dts: st: add node for the MALI gpu on stih410.dtsi
dt-bindings: gpu: mali-utgard: Add st,stih410-mali compatible
Link: https://lore.kernel.org/r/f44cb1f0-4d91-4e25-8b1f-3dd9a7bed62b@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into soc/dt
i.MX ARM device tree change for 6.14:
- Clean up TQMa7x device trees (Alexander Stein)
- Correct node name pattern for mdio-gpio devices (Fabio Estevam)
- Update deprecated GPIO properties for Generic ASoC Sound Card device
(Geert Uytterhoeven)
- Set USB dr_mode property to OTG explicitly for imx6qdl-sabresd based
boards (Hui Wang)
- Update MAINTAINERS entry for DH electronics DHSOM boards (Marek Vasut)
- A series from Stefan Kerkmann to add phy-3p0-supply for usb phys
* tag 'imx-dt-6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx: Use the correct mdio pattern
ARM: dts: imx6qdl-sabresd: add dr_mode to usbotg
ARM: dts: imx6qdl-apalis: Change to "adi,force-bt656-4"
ARM: dts: imx6sx: add phy-3p0-supply to usb phys
ARM: dts: imx6sl: add phy-3p0-supply to usb phys
ARM: dts: imx6qdl: add phy-3p0-supply to usb phys
MAINTAINERS: Update entry for DH electronics DHSOM SoMs and boards
ARM: dts: imx7[d]-mba7: add Ethernet PHY IRQ support
ARM: dts: imx7-mba7: Remove duplicated power supply
ARM: dts: imx7-mba7: Fix SD card vmmc-supply
ARM: dts: imx7-mba7: Add 3.3V and 5.0V regulators
ARM: dts: imx7-tqma7: add missing vs-supply for LM75A (rev. 01xxx)
ARM: dts: imx7-tqma7: Remove superfluous status="okay" property
ARM: dts: imx7-mba7: remove LVDS transmitter regulator
ARM: dts: imx: Switch to {hp,mic}-det-gpios
Link: https://lore.kernel.org/r/20250105095139.714590-3-shawnguo2@yeah.net
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into soc/dt
SoCFPGA DTS updates for v6.14
- Remove unused and undocumented property "snps,max-mtu"
- Add gpio and spi node for Agilex5
- Add VGIC maintenance interrupt for Agilex
- Use correct reset name of "stmmaceth-ocp" instead of "ahb"
- Drop unused #address-cells/#size-cells in the cyclone5-mcvevk
* tag 'socfpga_dts_updates_v6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
arm64: dts: altera: Remove unused and undocumented "snps,max-mtu" property
arm64: dts: socfpga: agilex5: Add gpio0 node and spi dma handshake id
arm64: dts: socfpga: agilex: Add VGIC maintenance interrupt
arm: dts: socfpga: use reset-name "stmmaceth-ocp" instead of "ahb"
ARM: dts: socfpga_cyclone5_mcvevk: Drop unused #address-cells/#size-cells
Link: https://lore.kernel.org/r/20250103023012.1268627-1-dinguyen@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt into soc/dt
Minor improvements in ARM DTS for v6.14
1. Marvell: Use un-deprecated hp-det-gpios (no ABI impact expected).
2. SoCFPGA: Drop spidev devices which are not properly described in DTS,
but are using some other compatibles. This was part of wider tree
effort to fix such incorrect hardware descriptions.
Important: Dropping this device node will have user-visible impact:
spidev device will not register.
* tag 'dt-cleanup-6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt:
ARM: dts: socfpga: remove non-existent DAC from CycloneV devkit
ARM: dts: marvell: mmp2-olpc-xo-1-75: Switch to {hp,mic}-det-gpios
Link: https://lore.kernel.org/r/20241231132847.135814-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into soc/dt
Samsung DTS ARM changes for v6.14
Few fixes and improvements for sound on Galaxy Tab3 (Exynos4212).
* tag 'samsung-dt-6.14' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: samsung: exynos4212-tab3: Drop interrupt from WM1811 codec
ARM: dts: samsung: exynos4212-tab3: Add MCLK2 clock to WM1811 codec config
ARM: dts: samsung: exynos4212-tab3: Fix headset mic, add jack detection
Link: https://lore.kernel.org/r/20241231131742.134329-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Fix following validation error:
arch/arm/boot/dts/mediatek/mt7623a-rfb-emmc.dtb: cir@10013000: $nodename:0: 'cir@10013000' does not match '^ir(-receiver)?(@[a-f0-9]+)?$'
from schema $id: http://devicetree.org/schemas/media/mediatek,mt7622-cir.yaml#
Fixes: 91044f38dae7 ("arm: dts: mt7623: add ir nodes to the mt7623.dtsi file")
Cc: linux-media@vger.kernel.org
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20240617094634.23173-1-zajec5@gmail.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Meta (Facebook) has a preference for all of our secondary flash
chips to be labelled "alt-bmc" for consistency of userspace tools
deal with updates. Bletchley, Harma, Minerva, and Catalina all
follow this convention but for some reason Yosemite4 is different.
Adjust the label in the dts to match the other platforms.
Signed-off-by: Patrick Williams <patrick@stwcx.xyz>
Link: https://patch.msgid.link/20250107162726.232402-1-patrick@stwcx.xyz
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
|
|
Specify the dimensions of the touchscreen propertly so that
no userspace configuration is needed for it.
Tested with x11 and weston on Debian bookworm.
What is in now is some debris from earlier tries to handle
scaling in kernel:
https://lore.kernel.org/linux-input/cover.1482936802.git.hns@goldelico.com/
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20241205204413.2466775-3-akemnade@kernel.org
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
According to the TRM [0] in 21.5.1.42 UART_SYSC Register,
the autoidle bit should not be set for UART, so remove the
appropriate SYSC_OMAP2_AUTOIDLE flag.
[0] https://www.ti.com/lit/ug/spruhl7i/spruhl7i.pdf
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Sukrut Bellary <sbellary@baylibre.com>
Link: https://lore.kernel.org/r/20241220223523.2125278-1-jm@ti.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Despite CM_IDLEST1_CORE and CM_FCLKEN1_CORE behaving normal,
disabling SPI leads to messages like when suspending:
Powerdomain (core_pwrdm) didn't enter target state 0
and according to /sys/kernel/debug/pm_debug/count off state is not
entered. That was not connected to SPI during the discussion
of disabling SPI. See:
https://lore.kernel.org/linux-omap/20230122100852.32ae082c@aktux/
The reason is that SPI is per default in slave mode. Linux driver
will turn it to master per default. It slave mode, the powerdomain seems to
be kept active if active chip select input is sensed.
Fix that by explicitly disabling the SPI3 pins which used to be muxed by
the bootloader since they are available on an optionally fitted header
which would require dtb overlays anyways.
Fixes: a622310f7f01 ("ARM: dts: gta04: fix excess dma channel usage")
CC: stable@vger.kernel.org
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20241204174152.2360431-1-andreas@kemnade.info
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add device tree support for the SAMA7D65 Curiosity board.
Update the Makefile to include the new device tree file.
uart6 is related to flexcom6, hence not sorted in alphabetical order.
Signed-off-by: Romain Sioen <romain.sioen@microchip.com>
Signed-off-by: Varshini Rajendran <varshini.rajendran@microchip.com>
Signed-off-by: Ryan Wanner <Ryan.Wanner@microchip.com>
Link: https://lore.kernel.org/r/20250107160850.120537-6-Ryan.Wanner@microchip.com
[claudiu.beznea: moved chosen node after alias for aphanumerically
sortage, added a space in front of <PIN_PD19__FLEXCOM6_IO1> for
alignment]
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
|
|
Add Device Tree for sama7d65 SoC.
Co-developed-by: Dharma Balasubiramani <dharma.b@microchip.com>
Signed-off-by: Dharma Balasubiramani <dharma.b@microchip.com>
Co-developed-by: Romain Sioen <romain.sioen@microchip.com>
Signed-off-by: Romain Sioen <romain.sioen@microchip.com>
Co-developed-by: Varshini Rajendran <varshini.rajendran@microchip.com>
Signed-off-by: Varshini Rajendran <varshini.rajendran@microchip.com>
Signed-off-by: Ryan Wanner <Ryan.Wanner@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Link: https://lore.kernel.org/r/20250107160850.120537-5-Ryan.Wanner@microchip.com
[claudiu.beznea: dropped comma typo from copyright, dropped space in
front of slow_xtal node, dropped empty space after slow_xtal node]
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
|
|
The system1 uses Intel common redundant (crps185) power supplies so move
to correct new crps driver.
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Link: https://patch.msgid.link/20241217173537.192331-5-ninad@linux.ibm.com
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
|
|
Disable U1 and U2 power-saving states to improve stability of USB.
These low-power link states, designed to reduce power consumption
during idle periods, can cause issues in latency-sensitive or high
throughput use cases. Over the years, some of the issues seen are
as follows:
1. In device mode of operation, when UVC is active, enabling U1/U2
is sometimes causing packets drops due to delay in entry/exit of
intermittent these low power states. These packet drops are often
reflected as missed isochronous transfers, as the controller wasn't
able to send packet in that microframe interval and hence glitches
are seen on the final transmitted video output.
2. On older targets like SM8150/SM8250/SM8350, there have been
throughput issues seen during tethering use cases.
3. On targets like SDX75, intermittent disconnects were observed
with certain cables due to impedence variations.
Disabling these intermittent power states enhances device stability
without affecting power usage.
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241231080932.3149448-3-quic_prashk@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Disable U1 and U2 power-saving states to improve stability of USB.
These low-power link states, designed to reduce power consumption
during idle periods, can cause issues in latency-sensitive or high
throughput use cases. Over the years, some of the issues seen are
as follows:
1. In device mode of operation, when UVC is active, enabling U1/U2
is sometimes causing packets drops due to delay in entry/exit of
intermittent these low power states. These packet drops are often
reflected as missed isochronous transfers, as the controller wasn't
able to send packet in that microframe interval and hence glitches
are seen on the final transmitted video output.
2. On older targets like SM8150/SM8250/SM8350, there have been
throughput issues seen during tethering use cases.
3. On targets like SDX75, intermittent disconnects were observed
with certain cables due to impedence variations.
Disabling these intermittent power states enhances device stability
without affecting power usage.
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241231080932.3149448-2-quic_prashk@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Enable the GPU on the stih410-b2260 board.
Signed-off-by: Alain Volmat <avolmat@me.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Add the entry for the GPU (Mali400) on the stih410.dtsi
Signed-off-by: Alain Volmat <avolmat@me.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Since these properties are common for all spi subnodes,
add them to SoC dtsi instead of board dts.
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
Link: https://lore.kernel.org/r/20241218080333.2225-3-mihai.sain@microchip.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
|
|
Since these properties are common for all spi subnodes,
add them to SoC dtsi instead of board dts.
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
Link: https://lore.kernel.org/r/20241218080333.2225-2-mihai.sain@microchip.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
|
|
Add no-1-8-v property to sdmmc0 node to keep VDDSDMMC power rail at 3.3V.
This property will stop the LDO regulator from switching to 1.8V when the
MMC core detects an UHS SD Card. VDDSDMMC power rail is used by all the
SDMMC interface pins in GPIO mode (PA0 - PA13).
On this board, PA10 is used as GPIO to enable the power switch controlling
USB Vbus for the USB Host. The change is needed to fix the PA10 voltage
level to 3.3V instead of 1.8V.
Fixes: 5d4c3cfb63fe ("ARM: dts: at91: sama5d27_wlsom1: add SAMA5D27 wlsom1 and wlsom1-ek")
Suggested-by: Mihai Sain <mihai.sain@microchip.com>
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Tested-by: Andrei Simion <andrei.simion@microchip.com>
Link: https://lore.kernel.org/r/20241119160107.598411-3-cristian.birsan@microchip.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
|
|
Add no-1-8-v property to sdmmc0 node to keep VDDSDMMC power rail at 3.3V.
This property will stop the LDO regulator from switching to 1.8V when the
MMC core detects an UHS SD Card. VDDSDMMC power rail is used by all the
SDMMC interface pins in GPIO mode (PA0 - PA13).
On this board, PA6 is used as GPIO to enable the power switch controlling
USB Vbus for the USB Host. The change is needed to fix the PA6 voltage
level to 3.3V instead of 1.8V.
Fixes: d85c4229e925 ("ARM: dts: at91: sama5d29_curiosity: Add device tree for sama5d29_curiosity board")
Suggested-by: Mihai Sain <mihai.sain@microchip.com>
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Tested-by: Andrei Simion <andrei.simion@microchip.com>
Link: https://lore.kernel.org/r/20241119160107.598411-2-cristian.birsan@microchip.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
|
|
Add sama7d65 pin descriptions.
Signed-off-by: Ryan Wanner <Ryan.Wanner@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Link: https://lore.kernel.org/r/a8f880b89cd4470526a2955a0b6aaaaa24ba65b8.1733505542.git.Ryan.Wanner@microchip.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
|
|
The only board that actually requires these properties is
meson8b-odroidc1.dts but that already sets it on it's own. Drop these
properties from meson.dtsi because otherwise they can cause dtc
warnings:
/soc/usb@c9040000: unnecessary #address-cells/#size-cells without
"ranges", "dma-ranges" or child "reg" property
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20241226220352.965505-1-martin.blumenstingl@googlemail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
mdio-gpio is not a valid pattern according to mdio-gpio.yaml.
Use the generic 'mdio' name to fix the following dt-schema warnings:
'mdio-gpio' does not match '^mdio(-(bus|external))?(@.+|-([0-9]+))?$'
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Currently there are 3 type of boards (imx6q|imx6qp|imx6dl-sabresd)
based on imx6qdl-sabresd.dtsi, they all do not set the dr_mode for
usbotg device node. The chipidea usb driver will configure it to otg
mode by default if the dr_mode is not set, but some testcases need to
parse the dr_mode from DT and decide the follow-up test strategy, here
set the dr_mode to otg explicitly for these 3 imx6qdl-sabresd based
boards.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
According to adv7180.yaml, the correct property name is
"adi,force-bt656-4".
Update it accordingly to fix several dt-schema warnings:
adv7280@21: 'adv,force-bt656-4' does not match any of the regexes: ...
imx6qdl-apalis.dtsi is the only in-tree kernel user of this property.
BSD does have a adv7180 driver, so should not be impacted.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The integrated usb phys are supplied by the 3p0 regulator, which has a
voltage range of 2.625V to 3.4V. Thus the min and max values are
corrected and the regulator added as a proper supply for the usb phys.
This fixes the following warnings during the probe of the mxs_phy
driver:
mxs_phy 20c9000.usbphy: supply phy-3p0 not found, using dummy regulator
mxs_phy 20ca000.usbphy: supply phy-3p0 not found, using dummy regulator
The regulator handling was introduced by commit `966d73152078 (usb: phy:
mxs: enable regulator phy-3p0 to improve signal qualilty, 2024-07-26)`.
Signed-off-by: Stefan Kerkmann <s.kerkmann@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The integrated usb phys are supplied by the 3p0 regulator, which has a
voltage range of 2.625V to 3.4V. Thus the min and max values are
corrected and the regulator added as a proper supply for the usb phys.
This fixes the following warnings during the probe of the mxs_phy
driver:
mxs_phy 20c9000.usbphy: supply phy-3p0 not found, using dummy regulator
mxs_phy 20ca000.usbphy: supply phy-3p0 not found, using dummy regulator
The 3p0 regulator handling was introduced by commit 966d73152078 ("usb:
phy: mxs: enable regulator phy-3p0 to improve signal qualilty")`.
Signed-off-by: Stefan Kerkmann <s.kerkmann@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The integrated usb phys are supplied by the 3p0 regulator, which has a
voltage range of 2.625V to 3.4V. Thus the min and max values are
corrected and the regulator added as a proper supply for the usb phys.
This fixes the following warnings during the probe of the mxs_phy
driver:
mxs_phy 20c9000.usbphy: supply phy-3p0 not found, using dummy regulator
mxs_phy 20ca000.usbphy: supply phy-3p0 not found, using dummy regulator
The 3p0 regulator handling was introduced by commit 966d73152078 ("usb:
phy: mxs: enable regulator phy-3p0 to improve signal qualilty")`.
Signed-off-by: Stefan Kerkmann <s.kerkmann@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This was initially copied from the Midas DTSI, but there is no
proof that the same interrupt is also used on the Tab 3. The pin
listed as the interrupt here is GPIO_HDMI_CEC on the Midas,
but for the Tab 3 it is the headset button GPIO - GPIO_EAR_SEND_END.
Drop the interrupt, since there is no proof that it is used.
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Link: https://lore.kernel.org/r/20240816-midas-audio-tab3-v2-5-48ee7f2293b3@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
In the schematics, the MCLK2 pin is shown as connected to CODEC_CLK32K,
which is derived from the same 32KHZ_PMIC clock as Bluetooth/WiFi and
GPS clocks. 32KHZ_PMIC is connected to the BTCLK pin, represented in
mainline as S2MPS11_CLK_BT.
Add the MCLK2 clock to the WM1811 codec clock property to properly
describe the hardware.
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Link: https://lore.kernel.org/r/20240816-midas-audio-tab3-v2-4-48ee7f2293b3@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
