| Age | Commit message (Collapse) | Author |
|---|
|
Fix USB-related warnings in imx6dl prtmvt device tree by disabling
unused usbphynop1 and usbphynop2 USB PHYs and over-current detection
which is not supported on USB h1 port. This fixes the following warnings
with the current kernel:
usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests
usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests
imx_usb 2184200.usb: No over current polarity defined
By the way, fix over-current detection on usbotg port.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix USB-related warnings in imx6dl alti6p device tree by disabling
unused usbphynop1 and usbphynop2 USB PHYs and properly configuring
over-current detection on related ports. This fixes the following
warnings with the current kernel:
usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests
usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests
imx_usb 2184200.usb: No over-current polarity defined
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch addresses several USB-related warnings in the device tree for
the imx6dl vicut1 system. Specifically, it disables the unused
usbphynop1 and usbphynop2 USB PHYs, and disables unsupported
over-current detection. This action mitigates the following kernel
warnings:
usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests
usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests
imx_usb 2184200.usb: No over-current polarity defined
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Kernel v6.3-rc1 prints errors due to missing trip points in thermal
zones. These errors indicate a lack of critical temperature threshold
settings, causing warnings at boot. To silence these errors, this patch
introduces trip points into the thermal zones of several imx6dl based
devices.
The following devices are updated:
- plym2m
- prtvt7
- victgo
- vicut1
These devices are automotive grade and expected to operate up to 105C.
An exception is the plym2m, an industrial grade device, which is
certified to work up to 85C.
The added trip points act as alert thresholds but do not trigger any
actions except warnings. This behavior is by design, as these devices
should maintain their performance until the end, without any thermal
throttling.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This commit adds the 'over-current-active-low' flag to the USB OTG node
in the imx6dl-lanmcu device tree. This flag is necessary because the
hardware signals over-current conditions by pulling the line low.
Without this flag, the kernel could misinterpret an over-current
condition, leading to unexpected behavior.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
In the imx6dl-lanmcu system, the usbh2 and usbh3 interfaces are not in
use. However, the related USB PHY nodes (usbphynop1 and usbphynop2) are
enabled by default in the imx6qdl.dtsi file, which can lead to confusion
and potential resource mismanagement.
This commit explicitly disables these unused USB PHY nodes in the
imx6dl-lanmcu device tree, aligning the configuration more accurately
with the actual hardware setup.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This commit addresses a misconfiguration in the prtwd2 device tree
source. Specifically, the ENET MDIO and MDC pins were mistakenly
assigned to the Ethernet block, while they are actually used by the I2C4
interface.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This touchscreen does not seem to be inverted in any axis, so remove these
DT properties.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This commit changes the default brightness level of the backlight on the
prtvt7 device from 20 to 65, roughly equivalent to 75% of the maximum
brightness level defined in the "brightness-levels" property.
The adjustment provides a more optimal default brightness for the
device, improving the overall user experience.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
According to Documentation/devicetree/bindings/sound/fsl,ssi.txt
'fsl,mode' should be specified for AC97 mode only.
The 'fsl,ssi' documentation doesn't say anything about specifying
'sound-dai-cells' so we'll remove that as well.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Devicetree node names should be generic. Use 'eeprom' as node name
to avoid devicetree check warning from at24.yaml.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
As documented in pfuze100.yaml, the correct name for the regulator is
"coin", so change it to fix the following DT check warning:
imx6ul-ccimx6ulsbcexpress.dtb: pmic@8: regulators: 'vcoin' does not match any of the regexes:
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Devicetree node names should be generic. Use 'pmic' as node name
to avoid devicetree check warning from pfuze100.yaml.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
According to Documentation/devicetree/bindings/sound/imx-audmux.yaml,
there must be a "mux-" prefix in the audmux port nodes.
Add the "mux-" prefix to avoid devicetree schema warnings.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Describe the SD1_VSELECT pad, which is necessary to allow UHS modes.
Also, to support higher SD card speed modes, describe the 100MHz and
200MHz SD card pinctrl entries.
Suggested-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Improve the devicetree description by adding the SD card regulator
that is controlled via GPIO5_2.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Correct the following warnings by adding the required supplies (AVDD, DVDD)
for the ov5640 node.
arch/arm/boot/dts/stm32mp157c-ev1.dtb: camera@3c: 'AVDD-supply' is a required property
From schema: Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml
arch/arm/boot/dts/stm32mp157c-ev1.dtb: camera@3c: 'DVDD-supply' is a required property
From schema: Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The generic ADC channel binding is recommended over legacy one, update the
DT to the modern binding. No functional change. For further details, see
commit which adds the generic binding to STM32 ADC binding document:
'664b9879f56e ("dt-bindings: iio: stm32-adc: add generic channel binding")'
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Use STM32 ADC generic bindings instead of legacy bindings on
DHCOR Testbench board.
The STM32 ADC specific binding to declare channels has been deprecated,
hence adopt the generic IIO channels bindings, instead.
The STM32MP151 device tree now exposes internal channels using the
generic binding. This makes the change mandatory here to avoid a mixed
use of legacy and generic binding, which is not supported by the driver.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Use STM32 ADC generic bindings instead of legacy bindings on
DHCOR DRC Compact board.
The STM32 ADC specific binding to declare channels has been deprecated,
hence adopt the generic IIO channels bindings, instead.
The STM32MP151 device tree now exposes internal channels using the
generic binding. This makes the change mandatory here to avoid a mixed
use of legacy and generic binding, which is not supported by the driver.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Use STM32 ADC generic bindings instead of legacy bindings on
emtrion GmbH Argon boards.
The STM32 ADC specific binding to declare channels has been deprecated,
hence adopt the generic IIO channels bindings, instead.
The STM32MP151 device tree now exposes internal channels using the
generic binding. This makes the change mandatory here to avoid a mixed
use of legacy and generic binding, which is not supported by the driver.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Use STM32 ADC generic bindings instead of legacy bindings on
STM32MP157c-ed1 board.
The STM32 ADC specific binding to declare channels has been deprecated,
hence adopt the generic IIO channels bindings, instead.
The STM32MP151 device tree now exposes internal channels using the
generic binding. This makes the change mandatory here to avoid a mixed
use of legacy and generic binding, which is not supported by the driver.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
U-Boot enables ADC1&2 to support USB power measurement and ADC
calibration on STM32MP15x Disco boards.
When leaving U-boot the ADCs do not return to power down state
to keep ADC linear calibration available for kernel.
Enable ADC1&2 by default on STM32MP15xx-DKx boards to align kernel
DT with Uboot. This avoids to shutdown the ADCs VDDA, while the
ADCs are not in power down.
Use STM32 ADC generic bindings instead of legacy bindings on
STM32MP15xx-DKx boards.
The ADC pins on Arduino connector are not set by default.
These pins are added in A7 Disco example DTs only.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Set STM32 ADC2 as a consumer of BSEC on STM32MP15, to retrieve
vrefint calibration data saved in OTP.
During the calibration process vrefp is set to 3.3V and the data
acquired is saved to the OTP. This data is used by the ADC driver
to calculated the actual value of vrefp according to the formula:
vrefp = 3.3 x vrefint_cal / vrefint_data
The vrefint channel provides the actual value of vrefp,
which can be used to correct ADC acquisition data.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Describe vrefint calibration cell to be retrieved through bsec.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Add STM32 ADC2 internal channels VREFINT and VDDCORE to STM32MP15x SoCs.
VBAT internal channel is not defined by default in SoC DT, and
has be defined in board DT when needed, instead. This avoids unwanted
current consumption on battery, when ADC conversions are performed
on any other channels.
The internal channels are defined in STM32MP15 SoC DT according to the
generic IIO channel bindings. The STM32 driver does not support a mixed
use of legacy and generic channels. When generic channels are defined,
legacy channels are ignored. This involves that the board device trees
using legacy bindings for ADC2, have to be reworked.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
make dtbs_check:
arch/arm/boot/dts/renesas/r8a7743-iwg20d-q7.dtb: backlight: pwms: [[58, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
arch/arm/boot/dts/renesas/r8a7743-iwg20d-q7-dbcm-ca.dtb: backlight: pwms: [[67, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
arch/arm/boot/dts/renesas/r8a7744-iwg20d-q7-dbcm-ca.dtb: backlight: pwms: [[67, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
arch/arm/boot/dts/renesas/r8a7744-iwg20d-q7.dtb: backlight: pwms: [[58, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
PWM specifiers referring to R-Car PWM Timer Controllers should contain
only two cells.
Fix this by dropping the bogus third cell.
Fixes: 6f89dd9e9325d05b ("ARM: dts: iwg20d-q7-common: Add LCD support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/6e5c3167424a43faf8c1fa68d9667b3d87dc86d8.1684855911.git.geert+renesas@glider.be
|
|
Add the '-@' DTC option for the Raspberry Pi devices. This option
populates the '__symbols__' node that contains all the necessary symbols
for supporting device-tree overlays (for instance from the firmware or
the bootloader) on these devices.
The Rasbperry Pi devices are well known for their GPIO header, that
allow various "HATs" or other modules do be connected and this enables
users to create out-of-tree device-tree overlays for these modules.
Please note that this change does increase the size of the resulting DTB
by ~40%. For example, with v6.4-rc1 increase in size is as follows:
bcm2711-rpi-400.dtb 27556 -> 38141 bytes
bcm2711-rpi-4-b.dtb 27484 -> 38069 bytes
bcm2711-rpi-cm4-io.dtb 27373 -> 38076 bytes
bcm2835-rpi-a.dtb 12879 -> 18235 bytes
bcm2835-rpi-a-plus.dtb 13015 -> 18371 bytes
bcm2835-rpi-b.dtb 12997 -> 18377 bytes
bcm2835-rpi-b-plus.dtb 13237 -> 18666 bytes
bcm2835-rpi-b-rev2.dtb 13085 -> 18514 bytes
bcm2835-rpi-cm1-io1.dtb 13109 -> 18528 bytes
bcm2835-rpi-zero.dtb 12923 -> 18311 bytes
bcm2835-rpi-zero-w.dtb 13449 -> 18889 bytes
bcm2836-rpi-2-b.dtb 14500 -> 20252 bytes
bcm2837-rpi-3-a-plus.dtb 14930 -> 20713 bytes
bcm2837-rpi-3-b.dtb 15107 -> 20979 bytes
bcm2837-rpi-3-b-plus.dtb 15463 -> 21443 bytes
bcm2837-rpi-cm3-io3.dtb 14429 -> 20098 bytes
bcm2837-rpi-zero-2-w.dtb 14781 -> 20524 bytes
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Link: https://lore.kernel.org/r/20220410225940.135744-3-aurelien@aurel32.net
[ukleinek: rebased to v6.4-rc1]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
|
|
This adds a DT node to hook up the internal temperature ADC to the
iio-hwmon driver. The various voltage + current ADCs are consumed and
exposed by their respective drivers, but this is not and is always
available. Naming chosen to match the axp20x_ prefix the power sensors
use.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/2a9bd53a65c4a154cccba622c60cbffcdceaeb95.1683719613.git.noodles@earth.li
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
These alternate pins for mmc2 are brought out to the 40 pin U14 header
on the C.H.I.P and can be used to add an external MMC device with a 4
bit interface. See
https://byteporter.com/ntc-chip-micro-sd-slot/
for further details on how.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/7949169f581cab37175602188f44bc26e79a45c0.1683719613.git.noodles@earth.li
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
The C.H.I.P has an rtl8723bs device with the bluetooth interface hooked
up on UART3. Support for this didn't exist in mainline when the DTS was
initially added, but it does now, so enable it.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/49ff7f3cc79838a55a89baae09a4ba12c88573fb.1683719613.git.noodles@earth.li
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
On Meson8 uart_B and uart_C do not work, because they are relying on
incorrect clocks. Change the references of pclk to the correct CLKID
(UART1 for uart_B and UART2 for uart_C), to allow use of the two uarts.
This was originally reported by Hans-Frieder Vogt for Meson8b [0], but
the same bug is also present in meson8.dtsi
[0] https://lore.kernel.org/linux-amlogic/trinity-bf20bcb9-790b-4ab9-99e3-0831ef8257f4-1680878185420@3c-app-gmx-bap55/
Fixes: 57007bfb5469 ("ARM: dts: meson8: Fix the UART device-tree schema validation")
Reported-by: Hans-Frieder Vogt <hfdevel@gmx.net> # for meson8b.dtsi
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20230516203029.1031174-1-martin.blumenstingl@googlemail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
Add the devices working with current drivers for the
Epson Moverio BT-200 AR glasses consisting of a control unit
and the glasses itself.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Message-Id: <20230313110409.2294154-1-andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The NAND wait pin is connected to the GPMC, but this is not mentioned
in the DT bindings. Let's fix this.
Signed-off-by: Alexander Shiyan <eagle.alexander923@gmail.com>
Message-Id: <20230524091157.775960-1-eagle.alexander923@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Enable MDSS, GPU and DSI panel output on the APQ8074 dragonboard.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230507190735.2333145-5-dmitry.baryshkov@linaro.org
|
|
Enable ADSP and Modem DSPs on APQ8074 dragonboard. The MSS region
differs from the one defined in the msm8974, so it overriden locally.
The modem is specified use mba.mbn instead of mbn.b00 (for the sake of
similarity with other platforms). This requires a patch for remoteproc
to be applied [1].
[1] https://lore.kernel.org/all/20230507172041.2320279-1-dmitry.baryshkov@linaro.org/
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230507190735.2333145-4-dmitry.baryshkov@linaro.org
|
|
Add the qcom,controlled-remotely property for the blsp2_bam
controller node. This board requires this, otherwise the board stalls
during the boot for some reason (most probably because TZ mishandles the
protection error and keeps on looping somewhere inside).
Fixes: 62bc81792223 dts: msm8974: Add blsp2_bam dma node
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230507190735.2333145-3-dmitry.baryshkov@linaro.org
|
|
The watch has a DRV2605 for haptics. Add a node for it based on the
values found in the downstream board file.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230430-drv260x-improvements-v1-5-1fb28b4cc698@z3ntu.xyz
|
|
This enables userspace to signal the bootloader to go into the
bootloader or recovery mode.
The magic values can be found in both the downstream kernel and the LK
kernel (bootloader).
Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Reviewed-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230520121933.15533-5-matti.lehtimaki@gmail.com
|
|
Add device node for the rpm-stats pseudo device.
Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230520121933.15533-4-matti.lehtimaki@gmail.com
|
|
Enable perf events on MSM8226 devices by adding the PMU node.
Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Reviewed-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230520121933.15533-3-matti.lehtimaki@gmail.com
|
|
Enable PCIe Endpoint controller on the SDX65 MTP board based
on Qualcomm SDX65 platform.
Signed-off-by: Rohit Agarwal <quic_rohiagar@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/1684432073-28490-6-git-send-email-quic_rohiagar@quicinc.com
|
|
Enable PCIe PHY on SDX65 MTP for PCIe EP.
Signed-off-by: Rohit Agarwal <quic_rohiagar@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/1684432073-28490-5-git-send-email-quic_rohiagar@quicinc.com
|
|
Add support for PCIe Endpoint controller on the
Qualcomm SDX65 platform.
Signed-off-by: Rohit Agarwal <quic_rohiagar@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/1684432073-28490-4-git-send-email-quic_rohiagar@quicinc.com
|
|
Add devicetree support for PCIe PHY used in SDX65 platform. This PHY is
used by the PCIe EP controller.
Signed-off-by: Rohit Agarwal <quic_rohiagar@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/1684432073-28490-3-git-send-email-quic_rohiagar@quicinc.com
|
|
Bindings expect WCNSS Bluetooth child to be named "bluetooth":
remoteproc@fb204000: smd-edge:wcnss: 'bt' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230421195437.31513-1-krzysztof.kozlowski@linaro.org
|
|
Match unit-address to reg entry to fix dtbs W=1 warnings:
Warning (simple_bus_reg): /soc/thermal-sensor@fc4a8000: simple-bus unit address format error, expected "fc4a9000"
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230420075053.41976-10-krzysztof.kozlowski@linaro.org
|
|
Regulators is not a bus, so drop incomplete simple-bus usage to fix dtbs
W=1 warning:
Warning (simple_bus_reg): /regulators/gpio-regulator: missing or empty reg/ranges property
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230420075053.41976-9-krzysztof.kozlowski@linaro.org
|
|
Regulators is not a bus, so drop incomplete simple-bus usage to fix dtbs
W=1 warnings:
Warning (simple_bus_reg): /regulators/regulator-fixed: missing or empty reg/ranges property
Warning (simple_bus_reg): /regulators/xc622a331mrg: missing or empty reg/ranges property
Warning (simple_bus_reg): /regulators/nds332p: missing or empty reg/ranges property
Warning (simple_bus_reg): /regulators/txb0104rgyr: missing or empty reg/ranges property
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230420075053.41976-8-krzysztof.kozlowski@linaro.org
|
|
Bindings expect USB controller node names to be named "usb".
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230420075053.41976-7-krzysztof.kozlowski@linaro.org
|
