| Age | Commit message (Collapse) | Author |
|---|
|
Add aliases for sdio and sdmmc to ensure consistent ordering of
mmc devices on boot
Signed-off-by: Tim Lunn <tim@feathertop.org>
Link: https://lore.kernel.org/r/20240215110425.934740-2-tim@feathertop.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Various control signals such as sfp module-absence, pci-e reset or led
gpios were missing pinctrl nodes, leaving any u-boot choices in place.
Since U-Boot is shared between multiple board variants, i.e. a388
clearfog pro / base, clearfog gtr l8 / s4, it is better to explicitly
configure functions.
Add explicit pinctrl entries for all gpios currently in use.
Additionally the loss-of-signal gpio specified is invalid, in fact los
only has a pull-up on the board but no gpio connection to the cpu.
Remove this stray reference.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Cosmetic change to increase future patches readability when adding new
pinctrl nodes.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Most arm board have a board-specific compatible string that allows e.g.
userspace to match specific firmware variants or apply specific
policies.
Add board-specific properties to both variants of the Clearfog GTR:
- solidrun,clearfog-gtr-l8
- solidrun,clearfog-gtr-s4
Introduction of a common parent (e.g. "solidrun,clearfog-gtr") is
omitted for brevity.
Since announcement of the two products no additional variants were added
it is assumed that there will always be just two.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Armada 388 Clearfog ("armada-388-clearfog.dts)" is a legacy filename for
the Armada 388 Clearfog Pro ("armada-388-clearfog-pro.dts").
The "Pro" suffix was only used when the smaller version, the "Base" got
released.
The two names refer to exactly the same hardware, therefore they should
share the same compatible strings.
Copy "solidrun,clearfog-pro-a1" compatible from the -pro dts and add it
to this legacy file.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
As the TWL6030 chip is the main power controller here, declare
it as system-power-controller
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Message-ID: <20240217082007.3238948-5-andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Configure the TWL6032 as system power controller to let the device
power off.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Message-ID: <20240217082007.3238948-4-andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Move the pending urls back to https:// and mark the ones that are no
longer accessible (http or https) as defunct.
Signed-off-by: Nishanth Menon <nm@ti.com>
Message-ID: <20240109195500.3833121-1-nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
for dra7 SoC
abb_{mpu,ivahd,dspeve,gpu} have 'reg' so they must have unit address to fix dtc
W=1 warnings:
Warning (unit_address_vs_reg): /ocp/regulator-abb-mpu: node has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): /ocp/regulator-abb-ivahd: node has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): /ocp/regulator-abb-dspeve: node has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): /ocp/regulator-abb-gpu: node has a reg or ranges property, but no unit name
Signed-off-by: Romain Naour <romain.naour@skf.com>
Message-ID: <20240123085551.733155-3-romain.naour@smile.fr>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
sys_32k_ck node have 'reg' so it must have unit address to fix dtc
W=1 warnings:
Warning (unit_address_vs_reg): /ocp/interconnect@4a000000/segment@0/target-module@2000/scm@0/scm_conf@0/clocks/clock-sys-32k: node has a reg or ranges property, but no unit name
Signed-off-by: Romain Naour <romain.naour@skf.com>
Message-ID: <20240123085551.733155-2-romain.naour@smile.fr>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
phy_gmii_sel node have 'reg' so it must have unit address to fix dtc
W=1 warnings:
Warning (unit_address_vs_reg): /ocp/interconnect@4a000000/segment@0/target-module@2000/scm@0/scm_conf@0/phy-gmii-sel: node has a reg or ranges property, but no unit name
Signed-off-by: Romain Naour <romain.naour@skf.com>
Message-ID: <20240123085551.733155-1-romain.naour@smile.fr>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
For the clksel clocks we are still using the legacy ti,bit-shift property
instead of the standard reg property. We can now use the reg property, so
let's do that for the clksel clocks.
To add the reg property, we switch to use #address-cells = <1>.
For now let's not update the clock-dss-tv-fck as it seems to share the same
register bit as the clock-dss-96m-fck and would introduce more warnings.
Cc: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
For the clksel clocks we are still using the legacy ti,bit-shift property
instead of the standard reg property. We can now use the reg property, so
let's do that for the clksel clocks.
To add the reg property, we switch to use #address-cells = <1>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
DT node names should be generic, so replace "weim" node name with
"memory-controller" in all i.MX SoC DT files.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The canonical node name for touchscreens is "touchscreen",
so update the i.MX6UL "tsc" node accordingly.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Replace all "xnur-gpio" with "xnur-gpios" in the i.MX6UL(L) Touchscreen
node, since the -gpio suffix is deprecated. All known implementations of
this binding can handle -gpio and -gpios since day 1, so this should be
fully backwards compatible.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
fsl,anatop should only be added to the usbphy nodes.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
pinctrl node name must be either pinctrl or pinmux.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Per davicom,dm9000.yaml, the Ethernet node name should be 'ethernet'.
Change it to fix the following schema warning:
imx1-apf9328.dtb: eth@4,c00000: $nodename:0: 'eth@4,c00000' does not match '^ethernet(@.*)?$'
from schema $id: http://devicetree.org/schemas/net/davicom,dm9000.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Per at24.yaml, the node name should be 'eeprom'.
Change it accordingly to fix the following schema warning:
imx28-evk.dtb: at24@51: $nodename:0: 'at24@51' does not match '^eeprom@[0-9a-f]{1,2}$'
from schema $id: http://devicetree.org/schemas/eeprom/at24.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable USB3 HW LPM feature.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This fixes the display not working on colibri imx7, the driver fails to
load with the following error:
mxsfb 30730000.lcdif: error -ENODEV: Cannot connect bridge
NXP i.MX7 LCDIF is connected to both the Parallel LCD Display and to a
MIPI DSI IP block, currently it's not possible to describe the
connection to both.
Remove the port endpoint from the SOC dtsi to prevent regressions, this
would need to be defined on the board DTS.
Reported-by: Hiago De Franco <hiagofranco@gmail.com>
Closes: https://lore.kernel.org/r/34yzygh3mbwpqr2re7nxmhyxy3s7qmqy4vhxvoyxnoguktriur@z66m7gvpqlia/
Fixes: edbbae7fba49 ("ARM: dts: imx7: add MIPI-DSI support")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
We identified that the PHYs actually do not work since commit 7da7b84fee58
("ARM: dts: imx6dl-yapp4: Move phy reset into switch node") as
a coincidence of several circumstances.
The reset signal is kept asserted by a pull-down resistor on the board
unless it is deasserted by GPIO from the SoC. This is to keep the switch
dead until it is configured properly by the kernel and user space.
Prior to the referenced commit the switch was reset by the FEC driver
and the reset GPIO was actively deasserted. The mdio-bus was scanned
and the attached switch and its PHYs were found and configured.
With the referenced commit the switch is reset by the qca8k driver.
Because of another bug in the qca8k driver, functionality of the reset
pin depends on its pre-kernel configuration. See commit c44fc98f0a8f
("net: dsa: qca8k: fix illegal usage of GPIO")
The problem did not appear until we removed support for the switch
and configuration of its reset pin from the bootloader.
To fix that, properly describe the internal mdio-bus configuration of
the qca8334 switch. The PHYs are internal to the switch and sit on its
internal mdio-bus.
Fixes: 7da7b84fee58 ("ARM: dts: imx6dl-yapp4: Move phy reset into switch node")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This change does not have any functional effect. The switch works just
fine without this patch as it has full access to all the addresses
on the bus. This is simply a clean-up to set the node name address
and reg address to the same value.
Fixes: 15b43e497ffd ("ARM: dts: imx6dl-yapp4: Use correct pseudo PHY address for the switch")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
If a bootloader does not configure the MAC address, devices come up with
a random MAC at the moment.
ocotp provides registers for storing the mac-address.
Configure those for i.MX6UL and i.MX6ULL allows net/core to retrieve it from
there.
Signed-off-by: Manuel Traut <manuel.traut@mt.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The USB PHY in the Allwinner R40 SoC seems to rely on voltage on the
VCC-TVIN/OUT supply pins for proper operation, on top of its own supply
voltage on VCC-USB. Without a 3.3V voltage supplied to VCC-TV*, USB
operation becomes unstable and can result in disconnects.
The Forlinx FETA40i-C SoM connects both the VCC-TVOUT and VCC-TVIN pins
to the ALDO1 rail of the PMIC, so we need to enable that rail for USB
operation. Since there is no supply property in the DT bindings for
the USB core, we need to always enable the regulator.
This fixes unstable USB operation on boards using the Forlinx FETA40i-C
module.
Signed-off-by: Fuyao Kashizuku <fuyao@sjterm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/ZYqRZev1g_mztff2@debian.cyg
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
Add sama7g5 flexcom specific compatible in DT with fallbacks.
Signed-off-by: Balakrishnan Sambath <balakrishnan.s@microchip.com>
Link: https://lore.kernel.org/r/20240223-b4-sama5d2-flexcom-yaml-v2-1-7e96c60c7701@microchip.com
[claudiu.beznea: adapt for flexcom10]
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
|
|
Align dmas to the opening '<' to comply with the dts coding style,
indentation section, point 3: "For arrays spanning across lines, it is
preferred to align the continued entries with opening < from the first
line."
Link: https://lore.kernel.org/r/20240218151353.3612621-3-claudiu.beznea@tuxon.dev
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
|
|
Align dmas to the opening '<' to comply with the dts coding style,
indentation section, point 3: "For arrays spanning across lines, it is
preferred to align the continued entries with opening < from the first
line."
Link: https://lore.kernel.org/r/20240218151353.3612621-2-claudiu.beznea@tuxon.dev
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
|
|
Add initial device tree of the SAMA7G54 Curiosity board.
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
Link: https://lore.kernel.org/r/20240215091524.14732-4-mihai.sain@microchip.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
|
|
Add flexcom 10 node for usage on the SAMA7G54 Curiosity board.
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
Link: https://lore.kernel.org/r/20240215091524.14732-3-mihai.sain@microchip.com
[claudiu.beznea: align dmas to the opening '<']
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/fixes
Renesas fixes for v6.8
- Add missing #interrupt-cells to DA9063 nodes.
* tag 'renesas-fixes-for-v6.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
ARM: dts: renesas: rcar-gen2: Add missing #interrupt-cells to DA9063 nodes
Link: https://lore.kernel.org/r/cover.1708597150.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add support for the MCIMXHDMICARD expansion card attached to the iMX53
QSB / QSRB platforms. This enables HDMI output on those devices.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add device-tree for LG Optimus 4X HD P880, which is a NVIDIA
Tegra30-based smartphone, originally running Android.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add device-tree for LG Optimus Vu P895, which is a NVIDIA
Tegra30-based smartphone, originally running Android.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
A recent rt5640 codec update requires mclk definition in the
device tree. Without mclk defined sound will not work.
Signed-off-by: Robert Eckelmann <longnoserob@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Sound Driver requires "reg-names" to get register info. Current driver
tries to get register info via "reg" instead of "reg-names" as backup
plan, but this support will be removed soon.
Use "reg-namess" for r8a7778 sound.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/87cyszpwmp.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
make dtbs_check W=2:
arch/arm/boot/dts/renesas/r8a7790-lager.dts:444.11-458.5: Warning (interrupt_provider): /i2c-mux4/pmic@58: Missing '#interrupt-cells' in interrupt provider
...
Fix this by adding the missing #interrupt-cells properties.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/a351e503ea97fb1af68395843f513925ff1bdf26.1707922460.git.geert+renesas@glider.be
|
|
The bridge does not have any cells on the node level, just on the
ports.
The VGA connector is actually named "J30" on the board so give it that
name in the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The bridge does not have any cells on the node level, just on the
ports.
The VGA connector is actually named "J1" on the board so give it that
name in the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When the development chip ROM was added, the "direct-mapped" compatible
value was already obsolete. In addition, the device node lacked the
accompanying "probe-type" property, causing the old physmap_of_core
driver to fall back to trying all available probe types.
Unfortunately this fallback was lost when the DT and pdata cases were
merged.
Fix this by using the modern "mtd-rom" compatible value instead.
Fixes: 5c3f5edbe0a1dff3 ("ARM: realview: add flash devices to the PB1176 DTS")
Fixes: 642b1e8dbed7bbbf ("mtd: maps: Merge physmap_of.c into physmap-core.c")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The formally correct node names have "ethernet-*" prefix on
switch, ports and port, fix it up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240211-gemini-dts-v1-4-6c09adeb4c2e@linaro.org
|
|
This maps the misc "reset", "setup" and "facory reset" keys to the
only key a standard userspace is likely to understand: KEY_RESTART.
On OpenWrt this will simply restart the system under controlled
forms.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240211-gemini-dts-v1-3-6c09adeb4c2e@linaro.org
|
|
These board strings were deprecated in the bindings ages ago,
switch the boards over to the real names.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240211-gemini-dts-v1-2-6c09adeb4c2e@linaro.org
|
|
The formally correct node names have "ethernet-*" prefix on
switch, ports, port and phy, fix it up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240211-gemini-dts-v1-1-6c09adeb4c2e@linaro.org
|
|
The dtc interrupt_map warning is off because its dependency,
interrupt_provider, is off by default. Fix all the warnings so it can be
enabled.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240213-arm-dt-cleanups-v1-4-f2dee1292525@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The dtc interrupt_provider warning is off by default. Fix all the warnings
so it can be enabled.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Reviewed-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com> #Broadcom
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20240213-arm-dt-cleanups-v1-2-f2dee1292525@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes
Some fixes to make devicetrees conform to bindings better (pwm irqs), dt
styling fixes (unneeded jaguar status, whitespaces, Cool Pi regulator
naming) and functionality fixes (px30 spi chipselect number, allowing
rk3588-evb1 to turn off, pcie lane numbers on CoolPi, wrong gpio-names
on Indidroid Nova and some CoolPi sdmmc aliases to match what uboot uses).
* tag 'v6.8-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Correct Indiedroid Nova GPIO Names
arm64: dts: rockchip: Drop interrupts property from rk3328 pwm-rockchip node
arm64: dts: rockchip: set num-cs property for spi on px30
arm64: dts: rockchip: minor rk3588 whitespace cleanup
arm64: dts: rockchip: drop unneeded status from rk3588-jaguar gpio-leds
ARM: dts: rockchip: Drop interrupts property from pwm-rockchip nodes
arm64: dts: rockchip: Fix the num-lanes of pcie3x4 on Cool Pi CM5 EVB
arm64: dts: rockchip: rename vcc5v0_usb30_host regulator for Cool Pi CM5 EVB
arm64: dts: rockchip: aliase sdmmc as mmc1 for Cool Pi CM5 EVB
arm64: dts: rockchip: aliase sdmmc as mmc1 for Cool Pi 4B
arm64: dts: rockchip: mark system power controller on rk3588-evb1
Link: https://lore.kernel.org/r/2450634.jE0xQCEvom@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
There's no documentation for a "amlogic,meson8b-rng" compatible string.
Keep the default compatible string from meson.dtsi which is
"amlogic,meson-rng" (which is also documented).
This fixes a binding check error.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240218111959.1811676-4-martin.blumenstingl@googlemail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
There's no documentation for a "amlogic,meson8-rng" compatible string.
Keep the default compatible string from meson.dtsi which is
"amlogic,meson-rng" (which is also documented).
This fixes a binding check error.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240218111959.1811676-3-martin.blumenstingl@googlemail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
