| Age | Commit message (Collapse) | Author |
|---|
|
Pull networking fixes from David Miller:
1) Clamp timeouts to INT_MAX in conntrack, from Jay Elliot.
2) Fix broken UAPI for BPF_PROG_TYPE_PERF_EVENT, from Hendrik
Brueckner.
3) Fix locking in ieee80211_sta_tear_down_BA_sessions, from Johannes
Berg.
4) Add missing barriers to ptr_ring, from Michael S. Tsirkin.
5) Don't advertise gigabit in sh_eth when not available, from Thomas
Petazzoni.
6) Check network namespace when delivering to netlink taps, from Kevin
Cernekee.
7) Kill a race in raw_sendmsg(), from Mohamed Ghannam.
8) Use correct address in TCP md5 lookups when replying to an incoming
segment, from Christoph Paasch.
9) Add schedule points to BPF map alloc/free, from Eric Dumazet.
10) Don't allow silly mtu values to be used in ipv4/ipv6 multicast, also
from Eric Dumazet.
11) Fix SKB leak in tipc, from Jon Maloy.
12) Disable MAC learning on OVS ports of mlxsw, from Yuval Mintz.
13) SKB leak fix in skB_complete_tx_timestamp(), from Willem de Bruijn.
14) Add some new qmi_wwan device IDs, from Daniele Palmas.
15) Fix static key imbalance in ingress qdisc, from Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
net: qcom/emac: Reduce timeout for mdio read/write
net: sched: fix static key imbalance in case of ingress/clsact_init error
net: sched: fix clsact init error path
ip_gre: fix wrong return value of erspan_rcv
net: usb: qmi_wwan: add Telit ME910 PID 0x1101 support
pkt_sched: Remove TC_RED_OFFLOADED from uapi
net: sched: Move to new offload indication in RED
net: sched: Add TCA_HW_OFFLOAD
net: aquantia: Increment driver version
net: aquantia: Fix typo in ethtool statistics names
net: aquantia: Update hw counters on hw init
net: aquantia: Improve link state and statistics check interval callback
net: aquantia: Fill in multicast counter in ndev stats from hardware
net: aquantia: Fill ndev stat couters from hardware
net: aquantia: Extend stat counters to 64bit values
net: aquantia: Fix hardware DMA stream overload on large MRRS
net: aquantia: Fix actual speed capabilities reporting
sock: free skb in skb_complete_tx_timestamp on error
s390/qeth: update takeover IPs after configuration change
s390/qeth: lock IP table while applying takeover changes
...
|
|
Use XAUI rather than XGMII for DSA link ports, as this is the interface
mode that the switches actually use. XAUI is the 4 lane bus with clock
per direction, whereas XGMII is a 32 bit bus with clock.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into fixes
Amlogic fixes for v4.15-rc
- GPIO interrupt fixes
- socinfo fix for GX series
- fix typo
* tag 'amlogic-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-gx: fix UART pclk clock name
meson-gx-socinfo: Fix package id parsing
ARM: meson: fix spelling mistake: "Couln't" -> "Couldn't"
ARM: dts: meson: fix the memory region of the GPIO interrupt controller
ARM: dts: meson: correct the sort order for the the gpio_intc node
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Two fixes for dts compiler warnings
These recently started showing up with better dtc checks being
introduced.
* tag 'omap-for-v4.15/fixes-dt-warnings' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix dm814x missing phy-cells property
ARM: dts: Fix elm interrupt compiler warning
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
"usb-nop-xceiv" is using the phy binding, but is missing #phy-cells
property. This is probably because the binding was the precursor to the phy
binding.
Fixes the following warning in nspire dts files:
Warning (phys_property): Missing property '#phy-cells' in node ...
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
We have phy-cells for usb_phy0, but it's missing for usb_phy1 and we get:
Warning (phys_property): Missing property '#phy-cells' in node
/ocp/l4ls@48000000/control@140000/usb-phy@1b00 or bad phandle
(referred from /ocp/usb@47400000/usb@47401800:phys[0])
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Looks like the interrupt property is missing the controller and level
information causing:
Warning (interrupts_property): interrupts size is (4), expected multiple
of 12 in /ocp/elm@48078000
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.15-rc cycle with two fixes for hangs with the
rest being compiler warning fixes and fixes for power states and devices
on various boards:
- Fix smatch issue introduced by recent omap device changes for legacy
resources
- Fix SRAM virt to phys related boot hang affecting n900 and other omap3 hs
devices found by pending CMA changes. While it seems that we have not hit
this in other use cases, let's fix it to avoid a nasty and hard to find
suprise as right now there is just luck keeping the SRAM virtual address
to physical address translation working with the 0xffff high_mask.
- Fix am335x reading of domain state registers that only exist for the
PM_CEFUSE domain and produce wrong results for other domains
- Fix missing setting for error code for omap device if allocation fails
- Fix missing modules_offs for omap3 MMC3 affecting n9/n950
- Fix cm_split_idlest() reading reserved registers showing wrong
idlestatus
- Fixes to correct #phy-cells property for compiler warnings that
recently started happening
- Add a missing OHCI remote-wakeup-connected property that I was supposed
to merge after the ohci-omap3 to ohci-platform changes but somehow managed
to drop. I only noticed this was missing while debugging the OHCI/EHCI GPS
and modem hang
- Fix a system hang with GPS or modem connected to the OHCI/EHCI bus that
typically happened within 20 - 40 minutes on an idle system. This turned
out to be an issue caused by using the parent interrupt controller directly
with the WUGEN + GIC stacked interrupt controller domains
- Fixes for logicpd-somlv GPMC for Ethernet and NAND that clearly
have been broken since we changed GPMC to use the interrupt controller
binding for some pins. And fix the wrong pin muxing for WLAN while at it
- Fixes for am437x interrupt and dma properties to fix compiler warnings
that recently started happening
* tag 'omap-for-v4.15/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am437x-cm-t43: Correct the dmas property of spi0
ARM: dts: am4372: Correct the interrupts_properties of McASP
ARM: dts: logicpd-somlv: Fix wl127x pinmux
ARM: dts: logicpd-som-lv: Fix gpmc addresses for NAND and enet
ARM: dts: Fix omap4 hang with GPS connected to USB by using wakeupgen
ARM: OMAP2+: Missing error code in omap_device_build()
ARM: AM33xx: PRM: Remove am33xx_pwrdm_read_prev_pwrst function
ARM: OMAP2+: Fix SRAM virt to phys translation for save_secure_ram_context
ARM: dts: Add remote-wakeup-connected for omap OHCI
ARM: dts: am33xx: Add missing #phy-cells to ti,am335x-usb-phy
ARM: dts: omap: Add missing #phy-cells to usb-nop-xceiv
ARM: OMAP2+: Fix smatch found issue for omap_device
ARM: OMAP2/3: CM: fix cm_split_idlest functionality
ARM: OMAP3: hwmod_data: add missing module_offs for MMC3
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.15:
- A fix for vf610-zii-dev-rev-c board which correct the unit-address
of I2C EEPROM node to match the 'reg' property.
- We thought the RTC block on i.MX53 is compatible with the one found
on i.MX25, and added the device for i.MX53 device tree. But it turns
out that's not the case, and we have to revert the change.
* tag 'imx-fixes-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
Revert "ARM: dts: imx53: add srtc node"
ARM: dts: vf610-zii-dev-rev-c: Fix the I2C EEPROM address
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
http://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for 4.15,
please pull the following:
- Stefan provides a fix for the BCM2835 (Raspberry Pi) to fix warnings about
missing "#phy-cells" properties
- Florian provides two fixes for Nortsthar Plus, one that uses the correct
interrupt specifiers for the timer/watchdog and one that disables SATA
on BCM9582**HR boards since that leads to unidentified hangs right now
* tag 'arm-soc/for-4.15/devicetree-fixes-1' of http://github.com/Broadcom/stblinux:
ARM: dts: NSP: Fix PPI interrupt types
ARM: dts: NSP: Disable AHCI controller for HR NSP boards
ARM: dts: bcm283x: Fix DTC warnings about missing phy-cells
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Renesas ARM Based SoC DT Fixes for v4.15
Add missing '#reset-cells' property to cpg nodes.
This flagged by recent dtc.
* tag 'renesas-dt-fixes-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: r8a779x: Add '#reset-cells' in cpg-mssr
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
"usb-nop-xceiv" is using the phy binding, but is missing #phy-cells
property. This is probably because the binding was the precursor to the phy
binding.
Fixes the following warning in Marvell dts files:
Warning (phys_property): Missing property '#phy-cells' in node ...
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
commit 200a575b68d2 ("ARM: dts: meson: organize devices in their corresponding busses")
organized all peripherals in busses so that the base register offset of
the bus doesn't have to be included in all child-nodes anymore.
The GPIO interrupt controller however specifies the register offset
without subtracting the "cbus" base address. This leads to a problem
where of_iomap inside the irq-meson-gpio driver fails because it
actually tries to map 0x182209880 (cbus base = 0xc1100000 + 0xc1109880
for the GPIO interrupt controller). Fix this by using 0x9880 as register
offset.
Fixes: 7d32bc03bcfb ("ARM: dts: meson8b: enable gpio interrupt controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Nodes are sorted by their register start address. Move gpio_intc to the
correct position.
No functional changes intended.
Fixes: 7d32bc03bcfb ("ARM: dts: meson8b: enable gpio interrupt controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This reverts commit 5b725054147deaf966b3919e10a86c6bfe946a18.
The rtc block on i.MX53 is a completely different hardware than the
one found on i.MX25.
Cc: <stable@vger.kernel.org> #4.14
Reported-by: Noel Vellemans <Noel.Vellemans@visionbms.com>
Suggested-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
at24mac602 should be at the I2C address 0x50, so that it matches the
'reg' property.
Fixes: d4cd158176c3 ("ARM: dts: vf610-zii-dev: Add .dts file for rev. C")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
|
|
The DMA binding for eDMA needs 2 parameters, not 1.
The second, missing parameter is the tptc to be used for the channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fixes the following warnings:
arch/arm/boot/dts/am437x-cm-t43.dtb: Warning (interrupts_property):
interrupts size is (8), expected multiple of 12 in
/ocp@44000000/mcasp@48038000
arch/arm/boot/dts/am437x-cm-t43.dtb: Warning (interrupts_property):
interrupts size is (8), expected multiple of 12 in
/ocp@44000000/mcasp@4803C000
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The pin assignment for the wl127x interrupt was incorrect. I am
not sure how this every worked. This also eliminates a conflict with
the SMC911x ethernet driver and properly moves pinmuxes for the
related gpio to omap3_pmx_wkup from omap3_pmx_core.
Fixes: ab8dd3aed011 ("ARM: DTS: Add minimal Support for Logic PD
DM3730 SOM-LV")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch fixes and issue where the NAND and GPMC based ethernet
controller stopped working. This also updates the GPMC settings
to be consistent with the Logic PD Torpedo development from the
commit listed above.
Fixes: 44e4716499b8 ("ARM: dts: omap3: Fix NAND device nodes")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
There's been a reproducable USB OHCI/EHCI cpuidle related hang on omap4
for a while that happens after about 20 - 40 minutes on an idle system
with some data feeding device being connected, like a USB GPS device or
a cellular modem.
This issue happens in cpuidle states C2 and C3 and does not happen if
cpuidle is limited to C1 state only. The symptoms are that the whole
system hangs and never wakes up from idle, and if a watchdog is
configured the system reboots after a while.
Turns out that OHCI/EHCI devices on omap4 are trying to use the GIC
interrupt controller directly as a parent instead of the WUGEN. We
need to pass the interrupts through WUGEN to GIC to provide the wakeup
events for the processor.
Let's fix the issue by removing the gic interrupt-parent and use the
default interrupt-parent wakeupgen instead. Note that omap5.dtsi had
this already fixes earlier by commit 7136d457f365 ("ARM: omap: convert
wakeupgen to stacked domains") but we somehow missed omap4 at that
point.
Fixes: 7136d457f365 ("ARM: omap: convert wakeupgen to stacked domains")
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This pull request brings in a fix for a warning that started occuring
when dtc from -next got merged.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Booting a kernel results in the kernel warning us about the following
PPI interrupts configuration:
[ 0.105127] smp: Bringing up secondary CPUs ...
[ 0.110545] GIC: PPI11 is secure or misconfigured
[ 0.110551] GIC: PPI13 is secure or misconfigured
Fix this by using the appropriate edge configuration for PPI11 and
PPI13, this is similar to what was fixed for Northstar (BCM5301X) in
commit 0e34079cd1f6 ("ARM: dts: BCM5301X: Correct GIC_PPI interrupt
flags").
Fixes: 7b2e987de207 ("ARM: NSP: add minimal Northstar Plus device tree")
Fixes: 1a9d53cabaf4 ("ARM: dts: NSP: Add TWD Support to DT")
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
The AHCI controller is currently enabled for all of these boards:
bcm958623hr and bcm958625hr would result in a hard hang on boot that we
cannot get rid of. Since this does not appear to have an easy and simple
fix, just disable the AHCI controller for now until this gets resolved.
Fixes: 70725d6e97ac ("ARM: dts: NSP: Enable SATA on bcm958625hr")
Fixes: d454c3762437 ("ARM: dts: NSP: Add new DT file for bcm958623hr")
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
With the latest dtc, we get many warnings about the missing
'#reset-cells' property in these controllers, e.g.:
arch/arm/boot/dts/r8a7790-lager.dtb: Warning (resets_property): Missing property '#reset-cells' in node /clock-controller@e6150000 or bad phandle (referred from /can@e6e80000:resets[0])
arch/arm/boot/dts/r8a7792-blanche.dtb: Warning (resets_property): Missing property '#reset-cells' in node /soc/clock-controller@e6150000 or bad phandle (referred from /soc/dma-controller@e6700000:resets[0])
arch/arm/boot/dts/r8a7792-wheat.dtb: Warning (resets_property): Missing property '#reset-cells' in node /soc/clock-controller@e6150000 or bad phandle (referred from /soc/ethernet@e6800000:resets[0])
arch/arm/boot/dts/r8a7793-gose.dtb: Warning (resets_property): Missing property '#reset-cells' in node /clock-controller@e6150000 or bad phandle (referred from /gpio@e6050000:resets[0])
arch/arm/boot/dts/r8a7794-alt.dtb: Warning (resets_property): Missing property '#reset-cells' in node /clock-controller@e6150000 or bad phandle (referred from /i2c@e6500000:resets[0])
arch/arm/boot/dts/r8a7794-silk.dtb: Warning (resets_property): Missing property '#reset-cells' in node /clock-controller@e6150000 or bad phandle (referred from /interrupt-controller@e61c0000:resets[0])
This adds it for the three r8a779x chips that were lacking it. The
binding mandates this as <1>, so this is the value I use.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[geert: Add fix for r8a7793.dtsi]
Fixes: 34fbd2b12761d111 ("ARM: dts: r8a7790: Add reset control properties")
Fixes: 6e11a322f1d7505d ("ARM: dts: r8a7792: Add reset control properties")
Fixes: 84fb19e1d201ba86 ("ARM: dts: r8a7793: Add reset control properties")
Fixes: 615beb759ca494a4 ("ARM: dts: r8a7794: Add reset control properties")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM device-tree updates from Arnd Bergmann:
"We add device tree files for a couple of additional SoCs in various
areas:
Allwinner R40/V40 for entertainment, Broadcom Hurricane 2 for
networking, Amlogic A113D for audio, and Renesas R-Car V3M for
automotive.
As usual, lots of new boards get added based on those and other SoCs:
- Actions S500 based CubieBoard6 single-board computer
- Amlogic Meson-AXG A113D based development board
- Amlogic S912 based Khadas VIM2 single-board computer
- Amlogic S912 based Tronsmart Vega S96 set-top-box
- Allwinner H5 based NanoPi NEO Plus2 single-board computer
- Allwinner R40 based Banana Pi M2 Ultra and Berry single-board computers
- Allwinner A83T based TBS A711 Tablet
- Broadcom Hurricane 2 based Ubiquiti UniFi Switch 8
- Broadcom bcm47xx based Luxul XAP-1440/XAP-810/ABR-4500/XBR-4500
wireless access points and routers
- NXP i.MX51 based Zodiac Inflight Innovations RDU1 board
- NXP i.MX53 based GE Healthcare PPD biometric monitor
- NXP i.MX6 based Pistachio single-board computer
- NXP i.MX6 based Vining-2000 automotive diagnostic interface
- NXP i.MX6 based Ka-Ro TX6 Computer-on-Module in additional variants
- Qualcomm MSM8974 (Snapdragon 800) based Fairphone 2 phone
- Qualcomm MSM8974pro (Snapdragon 801) based Sony Xperia Z2 Tablet
- Realtek RTD1295 based set-top-boxes MeLE V9 and PROBOX2 AVA
- Renesas R-Car V3M (R8A77970) SoC and "Eagle" reference board
- Renesas H3ULCB and M3ULCB "Kingfisher" extension infotainment boards
- Renasas r8a7745 based iWave G22D-SODIMM SoM
- Rockchip rk3288 based Amarula Vyasa single-board computer
- Samsung Exynos5800 based Odroid HC1 single-board computer
For existing SoC support, there was a lot of ongoing work, as usual
most of that concentrated on the Renesas, Rockchip, OMAP, i.MX,
Amlogic and Allwinner platforms, but others were also active.
Rob Herring and many others worked on reducing the number of issues
that the latest version of 'dtc' now warns about. Unfortunately there
is still a lot left to do.
A rework of the ARM foundation model introduced several new files for
common variations of the model"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (599 commits)
arm64: dts: uniphier: route on-board device IRQ to GPIO controller for PXs3
dt-bindings: bus: Add documentation for the Technologic Systems NBUS
arm64: dts: actions: s900-bubblegum-96: Add fake uart5 clock
ARM: dts: owl-s500: Add CubieBoard6
dt-bindings: arm: actions: Add CubieBoard6
ARM: dts: owl-s500-guitar-bb-rev-b: Add fake uart3 clock
ARM: dts: owl-s500: Set power domains for CPU2 and CPU3
arm: dts: mt7623: remove unused compatible string for pio node
arm: dts: mt7623: update usb related nodes
arm: dts: mt7623: update crypto node
ARM: dts: sun8i: a711: Enable USB OTG
ARM: dts: sun8i: a711: Add regulator support
ARM: dts: sun8i: a83t: bananapi-m3: Enable AP6212 WiFi on mmc1
ARM: dts: sun8i: a83t: cubietruck-plus: Enable AP6330 WiFi on mmc1
ARM: dts: sun8i: a83t: Move mmc1 pinctrl setting to dtsi file
ARM: dts: sun8i: a83t: allwinner-h8homlet-v2: Add AXP818 regulator nodes
ARM: dts: sun8i: a83t: bananapi-m3: Add AXP813 regulator nodes
ARM: dts: sun8i: a83t: cubietruck-plus: Add AXP818 regulator nodes
ARM: dts: sunxi: Add dtsi for AXP81x PMIC
arm64: dts: allwinner: H5: Restore EMAC changes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"Most of the commits are for defconfig changes, to enable newly added
drivers or features that people have started using. For the changed
lines lines, we have mostly cleanups, the affected platforms are OMAP,
Versatile, EP93xx, Samsung, Broadcom, i.MX, and Actions.
The largest single change is the introduction of the TI "sysc" bus
driver, with the intention of cleaning up more legacy code.
Two new SoC platforms get added this time:
- Allwinner R40 is a modernized version of the A20 chip, now with a
Quad-Core ARM Cortex-A7. According to the manufacturer, it is
intended for "Smart Hardware"
- Broadcom Hurricane 2 (Aka Strataconnect BCM5334X) is a family of
chips meant for managed gigabit ethernet switches, based around a
Cortex-A9 CPU.
Finally, we gain SMP support for two platforms: Renesas R-Car E2 and
Amlogic Meson8/8b, which were previously added but only supported
uniprocessor operation"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (118 commits)
ARM: multi_v7_defconfig: Select RPMSG_VIRTIO as module
ARM: multi_v7_defconfig: enable CONFIG_GPIO_UNIPHIER
arm64: defconfig: enable CONFIG_GPIO_UNIPHIER
ARM: meson: enable MESON_IRQ_GPIO in Kconfig for meson8b
ARM: meson: Add SMP bringup code for Meson8 and Meson8b
ARM: smp_scu: allow the platform code to read the SCU CPU status
ARM: smp_scu: add a helper for powering on a specific CPU
dt-bindings: Amlogic: Add Meson8 and Meson8b SMP related documentation
ARM: OMAP3: Delete an unnecessary variable initialisation in omap3xxx_hwmod_init()
ARM: OMAP3: Use common error handling code in omap3xxx_hwmod_init()
ARM: defconfig: select the right SX150X driver
arm64: defconfig: Enable QCOM_IOMMU
arm64: Add ThunderX drivers to defconfig
arm64: defconfig: Enable Tegra PCI controller
cpufreq: imx6q: Move speed grading check to cpufreq driver
arm64: defconfig: re-enable Qualcomm DB410c USB
ARM: configs: stm32: Add MDMA support in STM32 defconfig
ARM: imx: Enable cpuidle for i.MX6DL starting at 1.1
bus: ti-sysc: Fix unbalanced pm_runtime_enable by adding remove
bus: ti-sysc: mark PM functions as __maybe_unused
...
|
|
Pull ARM updates from Russell King:
- add support for ELF fdpic binaries on both MMU and noMMU platforms
- linker script cleanups
- support for compressed .data section for XIP images
- discard memblock arrays when possible
- various cleanups
- atomic DMA pool updates
- better diagnostics of missing/corrupt device tree
- export information to allow userspace kexec tool to place images more
inteligently, so that the device tree isn't overwritten by the
booting kernel
- make early_printk more efficient on semihosted systems
- noMMU cleanups
- SA1111 PCMCIA update in preparation for further cleanups
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (38 commits)
ARM: 8719/1: NOMMU: work around maybe-uninitialized warning
ARM: 8717/2: debug printch/printascii: translate '\n' to "\r\n" not "\n\r"
ARM: 8713/1: NOMMU: Support MPU in XIP configuration
ARM: 8712/1: NOMMU: Use more MPU regions to cover memory
ARM: 8711/1: V7M: Add support for MPU to M-class
ARM: 8710/1: Kconfig: Kill CONFIG_VECTORS_BASE
ARM: 8709/1: NOMMU: Disallow MPU for XIP
ARM: 8708/1: NOMMU: Rework MPU to be mostly done in C
ARM: 8707/1: NOMMU: Update MPU accessors to use cp15 helpers
ARM: 8706/1: NOMMU: Move out MPU setup in separate module
ARM: 8702/1: head-common.S: Clear lr before jumping to start_kernel()
ARM: 8705/1: early_printk: use printascii() rather than printch()
ARM: 8703/1: debug.S: move hexbuf to a writable section
ARM: add additional table to compressed kernel
ARM: decompressor: fix BSS size calculation
pcmcia: sa1111: remove special sa1111 mmio accessors
pcmcia: sa1111: use sa1111_get_irq() to obtain IRQ resources
ARM: better diagnostics with missing/corrupt dtb
ARM: 8699/1: dma-mapping: Remove init_dma_coherent_pool_size()
ARM: 8698/1: dma-mapping: Mark atomic_pool as __ro_after_init
..
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Documentation for digital TV (both kAPI and uAPI) are now in sync
with the implementation (except for legacy/deprecated ioctls). This
is a major step, as there were always a gap there
- New sensor driver: imx274
- New cec driver: cec-gpio
- New platform driver for rockship rga and tegra CEC
- New RC driver: tango-ir
- Several cleanups at atomisp driver
- Core improvements for RC, CEC, V4L2 async probing support and DVB
- Lots of drivers cleanup, fixes and improvements.
* tag 'media/v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (332 commits)
dvb_frontend: don't use-after-free the frontend struct
media: dib0700: fix invalid dvb_detach argument
media: v4l2-ctrls: Don't validate BITMASK twice
media: s5p-mfc: fix lockdep warning
media: dvb-core: always call invoke_release() in fe_free()
media: usb: dvb-usb-v2: dvb_usb_core: remove redundant code in dvb_usb_fe_sleep
media: au0828: make const array addr_list static
media: cx88: make const arrays default_addr_list and pvr2000_addr_list static
media: drxd: make const array fastIncrDecLUT static
media: usb: fix spelling mistake: "synchronuously" -> "synchronously"
media: ddbridge: fix build warnings
media: av7110: avoid 2038 overflow in debug print
media: Don't do DMA on stack for firmware upload in the AS102 driver
media: v4l: async: fix unregister for implicitly registered sub-device notifiers
media: v4l: async: fix return of unitialized variable ret
media: imx274: fix missing return assignment from call to imx274_mode_regs
media: camss-vfe: always initialize reg at vfe_set_xbar_cfg()
media: atomisp: make function calls cleaner
media: atomisp: get rid of storage_class.h
media: atomisp: get rid of wrong stddef.h include
...
|
|
This patch fixes the DTC warnings about missing property #phy-cells.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"A bigger diffstat than usual with the kbuild changes and a tree wide
fix in the binding documentation.
Summary:
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing
memory leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node.
The prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to
dtb compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage
Technology, shimafuji, Tecon Microprocessor Technologies, DH
electronics GmbH, Opal Kelly, and Next Thing"
* tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (55 commits)
dt-bindings: usb: add #phy-cells to usb-nop-xceiv
dt-bindings: Remove leading zeros from bindings notation
kbuild: handle dtb-y and CONFIG_OF_ALL_DTBS natively in Makefile.lib
MIPS: dts: remove bogus bcm96358nb4ser.dtb from dtb-y entry
kbuild: clean up *.dtb and *.dtb.S patterns from top-level Makefile
.gitignore: move *.dtb and *.dtb.S patterns to the top-level .gitignore
.gitignore: sort normal pattern rules alphabetically
dt-bindings: add vendor prefix for Next Thing Co.
scripts/dtc: Update to upstream version v1.4.5-6-gc1e55a5513e9
of: dynamic: fix memory leak related to properties of __of_node_dup
of: overlay: make pr_err() string unique
of: overlay: pr_err from return NOTIFY_OK to overlay apply/remove
of: overlay: remove unneeded check for NULL kbasename()
of: overlay: remove a dependency on device node full_name
of: overlay: simplify applying symbols from an overlay
of: overlay: avoid race condition between applying multiple overlays
of: overlay: loosen overly strict phandle clash check
of: overlay: expand check of whether overlay changeset can be removed
of: overlay: detect cases where device tree may become corrupt
of: overlay: minor restructuring
...
|
|
There are some conflicts between staging and media trees,
as reported by Stephen Rothwell <sfr@canb.auug.org.au>.
So, merge from staging.
* tag 'staging-4.15-rc1': (775 commits)
staging: lustre: add SPDX identifiers to all lustre files
staging: greybus: Remove redundant license text
staging: greybus: add SPDX identifiers to all greybus driver files
staging: ccree: simplify ioread/iowrite
staging: ccree: simplify registers access
staging: ccree: simplify error handling logic
staging: ccree: remove dead code
staging: ccree: handle limiting of DMA masks
staging: ccree: copy IV to DMAable memory
staging: fbtft: remove redundant initialization of buf
staging: sm750fb: Fix parameter mistake in poke32
staging: wilc1000: Fix bssid buffer offset in Txq
staging: fbtft: fb_ssd1331: fix mirrored display
staging: android: Fix checkpatch.pl error
staging: greybus: loopback: convert loopback to use generic async operations
staging: greybus: operation: add private data with get/set accessors
staging: greybus: loopback: Fix iteration count on async path
staging: greybus: loopback: Hold per-connection mutex across operations
staging: greybus/loopback: use ktime_get() for time intervals
staging: fsl-dpaa2/eth: Extra headroom in RX buffers
...
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big tty/serial driver pull request for 4.15-rc1.
Lots of serial driver updates in here, some small vt cleanups, and a
raft of SPDX and license boilerplate cleanups, messing up the diffstat
a bit.
Nothing major, with no realy functional changes except better hardware
support for some platforms.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (110 commits)
tty: ehv_bytechan: fix spelling mistake
tty: serial: meson: allow baud-rates lower than 9600
serial: 8250_fintek: Fix crash with baud rate B0
serial: 8250_fintek: Disable delays for ports != 0
serial: 8250_fintek: Return -EINVAL on invalid configuration
tty: Remove redundant license text
tty: serdev: Remove redundant license text
tty: hvc: Remove redundant license text
tty: serial: Remove redundant license text
tty: add SPDX identifiers to all remaining files in drivers/tty/
tty: serial: jsm: remove redundant pointer ts
tty: serial: jsm: add space before the open parenthesis '('
tty: serial: jsm: fix coding style
tty: serial: jsm: delete space between function name and '('
tty: serial: jsm: add blank line after declarations
tty: serial: jsm: change the type of local variable
tty: serial: imx: remove dead code imx_dma_rxint
tty: serial: imx: disable ageing timer interrupt if dma in use
serial: 8250: fix potential deadlock in rs485-mode
serial: m32r_sio: Drop redundant .data assignment
...
|
|
Add remote-wakeup-connected for omap OHCI as that's needed by
ohci-platform driver.
Cc: devicetree@vger.kernel.org
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
"ti,am335x-usb-phy" is using the phy binding, but is missing #phy-cells
property. Fixes the following warning in TI dts files:
Warning (phys_property): Missing property '#phy-cells' in node ...
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
"usb-nop-xceiv" is using the phy binding, but is missing #phy-cells
property. This is probably because the binding was the precursor to the phy
binding.
Fixes the following warning in OMAP dts files:
Warning (phys_property): Missing property '#phy-cells' in node ...
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
If CONFIG_OF_ALL_DTBS is enabled, "make ARCH=arm64 dtbs" compiles each
DTB twice; one from arch/arm64/boot/dts/*/Makefile and the other from
the dtb-$(CONFIG_OF_ALL_DTBS) line in arch/arm64/boot/dts/Makefile.
It could be a race problem when building DTBS in parallel.
Another minor issue is CONFIG_OF_ALL_DTBS covers only *.dts in vendor
sub-directories, so this broke when Broadcom added one more hierarchy
in arch/arm64/boot/dts/broadcom/<soc>/.
One idea to fix the issues in a clean way is to move DTB handling
to Kbuild core scripts. Makefile.dtbinst already recognizes dtb-y
natively, so it should not hurt to do so.
Add $(dtb-y) to extra-y, and $(dtb-) as well if CONFIG_OF_ALL_DTBS is
enabled. All clutter things in Makefiles go away.
As a bonus clean-up, I also removed dts-dirs. Just use subdir-y
directly to traverse sub-directories.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
[robh: corrected BUILTIN_DTB to CONFIG_BUILTIN_DTB]
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
|
|
|
|
We need to add "clean-files" in Makfiles to clean up DT blobs, but we
often miss to do so.
Since there are no source files that end with .dtb or .dtb.S, so we
can clean-up those files from the top-level Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Most of DT files are compiled under arch/*/boot/dts/, but we have some
other directories, like drivers/of/unittest-data/. We often miss to
add gitignore patterns per directory. Since there are no source files
that end with .dtb or .dtb.S, we can ignore the patterns globally.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "Rockchip dts32 updates for 4.15 part2" from Heiko Stübner:
CEC support for the two rk3288-firefly variants and general hdmi support
for the firefly-reload. A lot of additions and corrections for the
rk3288-vyasa and thermal support for the rv1108.
* tag 'v4.15-rockchip-dts32-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: enable the hdmi output on the rk3288-firefly-reload
ARM: dts: rockchip: define the two possible rk3288 CEC pins
ARM: dts: rockchip: add the cec clk for dw-hdmi on rk3288
ARM: dts: rockchip: Add io domains for rk3288-vyasa
ARM: dts: rockchip: Add usb otg for rk3288-vyasa
ARM: dts: rockchip: Add usb host for rk3288-vyasa
ARM: dts: rockchip: Add gmac support for rk3288-vyasa board
ARM: dts: rockchip: Add regulators for rk3288-vyasa
ARM: dts: rockchip: Use vmmc-supply from PMIC on rk3288-vyasa
ARM: dts: rockchip: Remove vdd_log from rk808, DCDC_REG1 on rk3288-vyasa
ARM: dts: rockchip: enable tsadc module on RV1108 evaluation board
ARM: dts: rockchip: add thermal nodes for RV1108 SoC
ARM: dts: rockchip: add tsadc node for RV1108 SoC
ARM: dts: rockchip: add RGA device node for RK3288
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Pull "Allwinner DT changes for 4.15, take 2" from Maxime Ripard:
Here are a few commits that would be great to get in 4.15, given how
long they've been hanging around.
The first and most important one is the reintroduction of the EMAC DT
changes after they've been reverted at the last minute in 4.13.
There's a arm64 patch that crept in because the H5 and H3 share a
common DTSI that is located in arch/arm, and merging that patch
through the arm64 PR, especially given the pull requests that have
already been sent, would just have generated too many conflicts.
* tag 'sunxi-dt-for-4.15-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: a711: Enable USB OTG
ARM: dts: sun8i: a711: Add regulator support
ARM: dts: sun8i: a83t: bananapi-m3: Enable AP6212 WiFi on mmc1
ARM: dts: sun8i: a83t: cubietruck-plus: Enable AP6330 WiFi on mmc1
ARM: dts: sun8i: a83t: Move mmc1 pinctrl setting to dtsi file
ARM: dts: sun8i: a83t: allwinner-h8homlet-v2: Add AXP818 regulator nodes
ARM: dts: sun8i: a83t: bananapi-m3: Add AXP813 regulator nodes
ARM: dts: sun8i: a83t: cubietruck-plus: Add AXP818 regulator nodes
ARM: dts: sunxi: Add dtsi for AXP81x PMIC
arm64: dts: allwinner: H5: Restore EMAC changes
ARM: dts: sunxi: Restore EMAC changes (boards)
ARM: dts: sunxi: h3/h5: represent the mdio switch used by sun8i-h3-emac
arm: dts: sunxi: h3/h5: Restore EMAC changes
dt-bindings: net: dwmac-sun8i: update documentation about integrated PHY
dt-bindings: net: Restore sun8i dwmac binding
|
|
into next/dt
Pull "Mediatek: 32-bit DTS updates for v4.15" from Matthias Brugger:
- mt7623 update nodes to binding description
- mt2701 add display pwn nodes
- mt2701 update audio node description
* tag 'v4.14-next-dts32-2' of https://github.com/mbgg/linux-mediatek:
arm: dts: mt7623: remove unused compatible string for pio node
arm: dts: mt7623: update usb related nodes
arm: dts: mt7623: update crypto node
arm: dts: mediatek: update audio node for mt2701 and mt7623
arm: dts: mt2701: enable display pwm backlight
arm: dts: mt2701: add pwm backlight device node
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions into next/dt
Pull "Actions Semi ARM based SoC DT for v4.15" from Andreas Färber:
This updates the Guitar board DT with a clock node for the debug UART
and adds a new DT for the CubieBoard6.
It also updates the S500 DT with CPU power domains.
* tag 'actions-arm-dt-for-4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions:
ARM: dts: owl-s500: Add CubieBoard6
dt-bindings: arm: actions: Add CubieBoard6
ARM: dts: owl-s500-guitar-bb-rev-b: Add fake uart3 clock
ARM: dts: owl-s500: Set power domains for CPU2 and CPU3
|
|
Pull ARM fixes from Russell King:
- omit EFI memory map sorting, which was recently introduced, but
caused problems with the decompressor due to additional sections
being emitted.
- avoid unaligned load fault-generating instructions in the
decompressor by switching to a private unaligned implementation.
- add a symbol into the decompressor to further debug non-boot
situations (ld's documentation is extremely poor for how "." works,
ld doesn't seem to follow its own documentation!)
- parse endian information to sparse
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: add debug ".edata_real" symbol
ARM: 8716/1: pass endianness info to sparse
efi/libstub: arm: omit sorting of the UEFI memory map
ARM: 8715/1: add a private asm/unaligned.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Only two patches came in over the last two weeks: Uniphier USB support
needs additional clocks enabled (on both 32-bit and 64-bit ARM), and a
Marvell MVEBU stability issue has been fixed"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: mvebu: pl310-cache disable double-linefill
arm64: dts: uniphier: add STDMAC clock to EHCI nodes
ARM: dts: uniphier: add STDMAC clock to EHCI nodes
|
|
Add a Device Tree for Cubietech CubieBoard6.
Cc: support@cubietech.com
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Add a fixed-clock for baudrate 115200.
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
