| Age | Commit message (Collapse) | Author |
|---|
|
The i2c handling in tfp410 driver, which handles converting parallel RGB
to DVI, was changed in 958f2717b84e88bf833d996997fda8f73276f2af
(OMAPDSS: TFP410: pdata rewrite). The patch changed what value the
driver considers as invalid/undefined. Before the patch, 0 was the
invalid value, but as 0 is a valid bus number, the patch changed this to
-1.
However, the fact was missed that many board files do not define the bus
number at all, thus it's left to 0. This causes the driver to fail to
get the i2c bus, exiting from the driver's probe with an error, meaning
that the DVI output does not work for those boards.
This patch fixes the issue by changing the i2c_bus number field in the
driver's platform data from u16 to int, and setting the bus number to -1
in the board files for the boards that did not define the bus. The
exception is devkit8000, for which the bus is set to 1, which is the
correct bus for that board.
The bug exists in v3.5+ kernels.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Thomas Weber <thomas@tomweber.eu>
Cc: Thomas Weber <thomas@tomweber.eu>
Cc: <stable@vger.kernel.org> # v3.5+
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Based on earlier discussions[1] we attempted to find a suitable
location for the omap DMA header in commit 2b6c4e73 (ARM: OMAP:
DMA: Move plat/dma.h to plat-omap/dma-omap.h) until the conversion
to dmaengine is complete.
Unfortunately that was before I was able to try to test compile
of the ARM multiplatform builds for omap2+, and the end result
was not very good.
So I'm creating yet another all over the place patch to cut the
last dependency for building omap2+ for ARM multiplatform. After
this, we have finally removed the driver dependencies to the
arch/arm code, except for few drivers that are being worked on.
The other option was to make the <plat-omap/dma-omap.h> path
to work, but we'd have to add some new header directory to for
multiplatform builds.
Or we would have to manually include arch/arm/plat-omap/include
again from arch/arm/Makefile for omap2+.
Neither of these alternatives sound appealing as they will
likely lead addition of various other headers exposed to the
drivers, which we want to avoid for the multiplatform kernels.
Since we already have a minimal include/linux/omap-dma.h,
let's just use that instead and add a note to it to not
use the custom omap DMA functions any longer where possible.
Note that converting omap DMA to dmaengine depends on
dmaengine supporting automatically incrementing the FIFO
address at the device end, and converting all the remaining
legacy drivers. So it's going to be few more merge windows.
[1] https://patchwork.kernel.org/patch/1519591/#
cc: Russell King <linux@arm.linux.org.uk>
cc: Kevin Hilman <khilman@ti.com>
cc: "Benoît Cousson" <b-cousson@ti.com>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: "David S. Miller" <davem@davemloft.net>
cc: Vinod Koul <vinod.koul@intel.com>
cc: Dan Williams <djbw@fb.com>
cc: Mauro Carvalho Chehab <mchehab@infradead.org>
cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
cc: David Woodhouse <dwmw2@infradead.org>
cc: Kyungmin Park <kyungmin.park@samsung.com>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
cc: Hans Verkuil <hans.verkuil@cisco.com>
cc: Vaibhav Hiremath <hvaibhav@ti.com>
cc: Lokesh Vutla <lokeshvutla@ti.com>
cc: Rusty Russell <rusty@rustcorp.com.au>
cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
cc: Afzal Mohammed <afzal@ti.com>
cc: linux-crypto@vger.kernel.org
cc: linux-media@vger.kernel.org
cc: linux-mtd@lists.infradead.org
cc: linux-usb@vger.kernel.org
cc: linux-fbdev@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Modify the board files to use the SoC-specific system restart
functions. At this point it's possible to remove omap_prcm_restart()
from mach-omap2/prcm.c.
While removing the prototypes for the now-unused restart functions, clean
up a few more obsolete prototypes in mach-omap2/clock.h.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
|
|
omap-for-v3.8/cleanup-headers
Conflicts:
arch/arm/mach-omap1/clock.c
arch/arm/mach-omap2/board-2430sdp.c
arch/arm/mach-omap2/board-4430sdp.c
arch/arm/mach-omap2/board-cm-t35.c
arch/arm/mach-omap2/board-igep0020.c
arch/arm/mach-omap2/board-ldp.c
arch/arm/mach-omap2/board-omap3beagle.c
arch/arm/mach-omap2/board-omap3logic.c
arch/arm/mach-omap2/board-omap4panda.c
arch/arm/mach-omap2/board-overo.c
arch/arm/mach-omap2/board-rm680.c
arch/arm/mach-omap2/board-rx51.c
arch/arm/mach-omap2/twl-common.c
arch/arm/mach-omap2/usb-host.c
arch/arm/mach-omap2/usb-musb.c
|
|
Let's move what we can from plat/usb.h to the local usb.h
for ARM common zImage support.
This is needed so we can remove plat/usb.h for ARM common
zImage support.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Partha Basak <parthab@india.ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: linux-usb@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We want to remove plat/cpu.h. To do this, let's first split
it to private soc.h to mach-omap1 and mach-omap2. We have to
keep plat/cpu.h around until the remaining drivers are fixed,
so let's include the local soc.h in plat/cpu.h and for drivers
still including plat/cpu.h.
Once the drivers are fixed not to include plat/cpu.h, we
can remove the file.
This is needed for the ARM common zImage support.
[tony@atomide.com: updated to not print a warning]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
omap-for-v3.8/cleanup-headers
Conflicts:
arch/arm/mach-omap2/board-3430sdp.c
arch/arm/mach-omap2/board-h4.c
arch/arm/mach-omap2/board-rx51-peripherals.c
arch/arm/mach-omap2/board-rx51.c
arch/arm/mach-omap2/pm34xx.c
drivers/mtd/nand/omap2.c
drivers/mtd/onenand/omap2.c
|
|
Move plat/dma.h to plat-omap/dma-omap.h as part of single
zImage work
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Requirement of gpmc header outside of mach-omap2 has been
cutoff, move gpmc header file in plat-omap folder to local
mach-omap2 folder
Objective - common zImage participation of omap
Signed-off-by: Afzal Mohammed <afzal@ti.com>
|
|
This can be local to mach-omap2.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the omap include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: "Benoît Cousson" <b-cousson@ti.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: Jean Pihet <j-pihet@ti.com>
Cc: J Keerthy <j-keerthy@ti.com>
Cc: linux-omap@vger.kernel.org
|
|
As the plat and mach includes need to disappear for single zImage work,
we need to remove plat/hardware.h.
Do this by splitting plat/hardware.h into omap1 and omap2+ specific files.
The old plat/hardware.h already has omap1 only defines, so it gets moved
to mach/hardware.h for omap1. For omap2+, we use the local soc.h
that for now just includes the related SoC headers to keep this patch more
readable.
Note that the local soc.h still includes plat/cpu.h that can be dealt
with in later patches. Let's also include plat/serial.h from common.h for
all the board-*.c files. This allows making the include files local later
on without patching these files again.
Note that only minimal changes are done in this patch for the
drivers/watchdog/omap_wdt.c driver to keep things compiling. Further
patches are needed to eventually remove cpu_is_omap usage in the drivers.
Also only minimal changes are done to sound/soc/omap/* to remove the
unneeded includes and to define OMAP44XX_MCPDM_L3_BASE locally so there's
no need to include omap44xx.h.
While at it, also sort some of the includes in the standard way.
Cc: linux-watchdog@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Liam Girdwood <lrg@ti.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can't use hardcoded interrupts for SPARSE_IRQ, and can replace
the hardcoded gpio_base with twl_gpiochip.base after it's been
allocated.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
struct omap_board_config_kernel defined in the board files
is always empty and does not bring any added value.
Remove the struct omap_board_config_kernel instances from the board
files.
Also remove the omap_get_nr_config() macro and the omap_get_var_config()
function as both are not used for quite a long time (if ever).
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull sweeping late_initcall cleanup for arm-soc from Olof Johansson:
"This is a patch series from Shawn Guo that moves from individual
late_initcalls() to using a member in the machine structure to invoke
a platform's late initcalls.
This cleanup is a step in the move towards multiplatform kernels since
it would reduce the need to check for compatible platforms in each and
every initcall."
Fix up trivial conflicts in arch/arm/mach-{exynos/mach-universal_c210.c,
imx/mach-cpuimx51.c, omap2/board-generic.c} due to changes nearby (and,
in the case of cpuimx51.c the board support being deleted)
* tag 'cleanup-initcall' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: ux500: use machine specific hook for late init
ARM: tegra: use machine specific hook for late init
ARM: shmobile: use machine specific hook for late init
ARM: sa1100: use machine specific hook for late init
ARM: s3c64xx: use machine specific hook for late init
ARM: prima2: use machine specific hook for late init
ARM: pnx4008: use machine specific hook for late init
ARM: omap2: use machine specific hook for late init
ARM: omap1: use machine specific hook for late init
ARM: msm: use machine specific hook for late init
ARM: imx: use machine specific hook for late init
ARM: exynos: use machine specific hook for late init
ARM: ep93xx: use machine specific hook for late init
ARM: davinci: use machine specific hook for late init
ARM: provide a late_initcall hook for platform initialization
|
|
Now that the tfp410 driver has been renamed in the code, this patch
finishes the renaming by renaming the files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
The driver for the TFP410 DPI-to-DVI chip was named quite badly as "DVI
panel driver". This patch renames the code to use tfp410 name for the
driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Now that the panel-dvi driver handles the PD (power-down) GPIO, we can
remove the custom PD handling from the board files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Otherwise omap_device_build() and omap_mux related functions
can't be marked as __init when twl is build as a module.
If a board is using GPIO pins or regulators configured by an
external chip, such as TWL PMIC on I2C bus, the board must
mark those MMC controllers as deferred. Additionally both
omap_hsmmc_init() and omap_hsmmc_late_init() must be called
by the board.
For MMC controllers using internal GPIO pins for card
detect and regulators the slots don't need to be marked
deferred. In this case calling omap_hsmmc_init() is sufficient.
Only mark the MMC slots using gpio_cd or gpio_wd as deferred
as noted by Igor Grinberg <grinberg@compulab.co.il>.
Note that this patch does not change the behaviour for
board-4430sdp.c board-omap4panda.c. These boards wrongly
rely on the omap_hsmmc.c init function callback to configure
the PMIC GPIO interrupt lines on external chip. If the PMIC
interrupt lines are not configured during init, they will
fail.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
power management changes for omap and imx
A significant part of the changes for these two platforms went into
power management, so they are split out into a separate branch.
* tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (65 commits)
ARM: imx6: remove __CPUINIT annotation from v7_invalidate_l1
ARM: imx6: fix v7_invalidate_l1 by adding I-Cache invalidation
ARM: imx6q: resume PL310 only when CACHE_L2X0 defined
ARM: imx6q: build pm code only when CONFIG_PM selected
ARM: mx5: use generic irq chip pm interface for pm functions on
ARM: omap: pass minimal SoC/board data for UART from dt
arm/dts: Add minimal device tree support for omap2420 and omap2430
omap-serial: Add minimal device tree support
omap-serial: Use default clock speed (48Mhz) if not specified
omap-serial: Get rid of all pdev->id usage
ARM: OMAP2+: hwmod: Add a new flag to handle hwmods left enabled at init
ARM: OMAP4: PRM: use PRCM interrupt handler
ARM: OMAP3: pm: use prcm chain handler
ARM: OMAP: hwmod: add support for selecting mpu_irq for each wakeup pad
ARM: OMAP2+: mux: add support for PAD wakeup interrupts
ARM: OMAP: PRCM: add suspend prepare / finish support
ARM: OMAP: PRCM: add support for chain interrupt handler
ARM: OMAP3/4: PRM: add functions to read pending IRQs, PRM barrier
ARM: OMAP2+: hwmod: Add API to enable IO ring wakeup
ARM: OMAP2+: mux: add wakeup-capable hwmod mux entries to dynamic list
...
|
|
Conflicts:
arch/arm/mach-exynos/cpu.c
The changes to arch/arm/mach-exynos/cpu.c were moved to
mach-exynos/common.c.
|
|
Hook these platforms restart code into the new restart hook rather
than using arch_reset().
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Padconf wakeup is used to wakeup uart after uart fclks/iclks are gated.
Rx-Pad wakeup was done by writing to rx-pad offset value populated in
serial.c idle_init. Remove the direct reading and writing into rx pad.
Remove the padconf field part of omap_uart_state struct and pad offsets
populated.
Now with mux framework support we can use mux_utilities
along with hmwod framework to handle io-pad configuration and enable rx-pad
wake-up mechanism.
To avoid breaking any board support add default mux data for all uart's
if mux info is not passed from board file.
With the default pads populated in serial.c wakeup capability for
rx pads is set, this can be used to enable uart_rx io-pad wakeup from
hwmod framework. The pad values in 3430sdp/4430sdp/omap4panda board file
are same as the default pad values populated in serial.c. Remove pad values
from 3430sdp/4430sdp/omap4panda board file and use the default pads
from serial.c file.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into devel-stable
Conflicts:
arch/arm/mach-omap2/board-4430sdp.c
arch/arm/mach-omap2/board-omap4panda.c
arch/arm/mach-omap2/include/mach/omap4-common.h
arch/arm/plat-omap/include/plat/irqs.h
The changes to omap4-common.h were moved to arch/arm/mach-omap2/common.h
and the other trivial conflicts resolved. The now empty ifdef in irqs.h
was also eliminated.
|
|
As suggested by Russell King - ARM Linux <linux@arm.linux.org.uk>,
there's no need to keep local prototypes in non-local headers.
Add mach-omap1/common.h and mach-omap2/common.h and move the
local prototypes there from plat/common.h and mach/omap4-common.h.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Convert the omap2plus platforms to be using CONFIG_MULTI_IRQ_HANDLER.
Each machine is modified to provide either omap2_intc_handle_irq(),
omap3_intc_handle_irq() or gic_handle_irq().
This allows for a major cleanup, removing the MULTI_OMAP setup
from the interrupt path.
Tested on both Panda and IGEPv2 (single kernel image)
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Omap cleanups conflicted with omap2_dss work in a nontrivial
way, this is the most logical fixup.
Conflicts:
arch/arm/mach-omap2/board-2430sdp.c
arch/arm/mach-omap2/board-4430sdp.c
arch/arm/mach-omap2/board-apollon.c
arch/arm/mach-omap2/board-h4.c
arch/arm/mach-omap2/board-ldp.c
arch/arm/mach-omap2/board-rx51.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
|
|
Multiple OMAP3/4 boards have a DVI framer output. This patch makes the
boards use the new panel-dvi driver, instead of the panel-generic-dpi
driver.
Separate drivers for fixed size panels and DVI framer gives us cleaner
driver code.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Introduce them for each omap variant and just make them all call
omap2_init_common_infrastructure for now. Do this for each board-*.c
file except for board-generic and board-omap3beagle as they use
the same machine ID for multiple SoCs.
No functional changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
There's no need to call omap2_init_common_devices from init_early.
It no longer does anything else except reprogram the memory timings
for some boards, so it's better to do it later so we have a chance
to get console messages if something goes wrong.
Move it to happen after omap_serial_init gets called. And while
patching it anyways, rename it to omap_sdrc_init as suggested by
Benoit Cousson <b-cousson@ti.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
Some regulator config can be moved out from board files,
since they are close to identical.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Reduce the amount of duplicated code by moving the common
configuration for twl4030/5030/tpsxx to the twl-common file.
Use the omap3_pmic_get_config function from board files to
properly configure the PMIC with the common fields.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
This is needed for the following patches so we can initialize the
rest of the hardware timers later on.
As with the init_irq calls, there's no need to do cpu_is_omap calls
during the timer init as we only care about the major omap generation.
This means that we can initialize the sys_timer with the .timer
entries alone.
Note that for now we just set stubs for the various sys_timer entries
that will get populated in a later patch. The following patches will
also remove the omap_dm_timer_init calls and change the init for the
rest of the hardware timers to happen with an arch_initcall.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
|
|
This allows us to remove cpu_is_omap calls from init_irq functions.
There should not be any need for cpu_is_omap calls as at this point.
During the timer init we only care about SoC generation, and not about
subrevisions.
The main reason for the patch is that we want to initialize only
minimal omap specific code from the init_early call.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
|
|
The serial*_data should have been marked as __initdata as per
it's usage in the board files. Fix the same to remove the
section mismatch warnings caused by it.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Silesh C V <silesh@ti.com>
[tony@atomide.com: updated with additional fixes from Silesh]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (33 commits)
OMAP3: PM: Boot message is not an error, and not helpful, remove it
OMAP3: cpuidle: change the power domains modes determination logic
OMAP3: cpuidle: code rework for improved readability
OMAP3: cpuidle: re-organize the C-states data
OMAP3: clean-up mach specific cpuidle data structures
OMAP3 cpuidle: remove useless SDP specific timings
usb: otg: OMAP4430: Powerdown the internal PHY when USB is disabled
usb: otg: OMAP4430: Fixing the omap4430_phy_init function
usb: musb: am35x: fix compile error when building am35x
usb: musb: OMAP4430: Power down the PHY during board init
omap: drop board-igep0030.c
omap: igep0020: add support for IGEP3
omap: igep0020: minor refactoring
omap: igep0020: name refactoring for future merge with IGEP3
omap: Remove support for omap2evm
arm: omap2plus: GPIO cleanup
omap: musb: introduce default board config
omap: move detection of NAND CS to common-board-devices
omap: use common initialization for PMIC i2c bus
omap: consolidate touch screen initialization among different boards
...
|
|
ssh://master.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into omap-for-linus
|
|
The cpuidle states settings can be overriden by some board-
specific settings, by calling omap3_pm_init_cpuidle.
Remove the 3430SDP specific states settings registration
since the figures are identical to the default ones (in cpuidle34xx.c).
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
use gpio_request_<one|array>() instead of multiple gpiolib calls,
remove unneeded variables, etc.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
arch/arm/plat-omap/include/plat/panel-generic-dpi.h is an include for
the OMAP DSS panel driver for generic DPI displays. A more logical place
for it is in include/video.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
arch/arm/plat-omap/include/plat/display.h is an include for the OMAP DSS
driver. A more logical place for it is in include/video.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Most boards use exactly the same configuration for musb initialization.
Create a default that can be shared amount different boards.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Introduce omap_pmic_init that registers i2c bus and PMIC device on that
bus and add omap2/3/4 wrappers for common cases.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add common-board-devices.c that will contain the code for peripheral
devices initializatoin shared between multiple boards.
Start small with touchscreen initialization.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Conflicts:
arch/arm/mach-omap2/board-overo.c
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (258 commits)
omap: zoom: host should not pull up wl1271's irq line
arm: plat-omap: iommu: fix request_mem_region() error path
OMAP2+: Common CPU DIE ID reading code reads wrong registers for OMAP4430
omap4: mux: Remove duplicate mux modes
omap: iovmm: don't check 'da' to set IOVMF_DA_FIXED flag
omap: iovmm: disallow mapping NULL address when IOVMF_DA_ANON is set
omap2+: mux: Fix compile when CONFIG_OMAP_MUX is not selected
omap4: board-omap4panda: Initialise the serial pads
omap3: board-3430sdp: Initialise the serial pads
omap4: board-4430sdp: Initialise the serial pads
omap2+: mux: Add macro for configuring static with omap_hwmod_mux_init
omap2+: mux: Remove the use of IDLE flag
omap2+: Add separate list for dynamic pads to mux
perf: add OMAP support for the new power events
OMAP4: Add IVA OPP enteries.
OMAP4: Update Voltage Rail Values for MPU, IVA and CORE
OMAP4: Enable 800 MHz and 1 GHz MPU-OPP
OMAP3+: OPP: Replace voltage values with Macros
OMAP3: wdtimer: Fix CORE idle transition
Watchdog: omap_wdt: add fine grain runtime-pm
...
Fix up various conflicts in
- arch/arm/mach-omap2/board-omap3evm.c
- arch/arm/mach-omap2/clock3xxx_data.c
- arch/arm/mach-omap2/usb-musb.c
- arch/arm/plat-omap/include/plat/usb.h
- drivers/usb/musb/musb_core.h
|
|
Use the mux framework to initialise the serial pads.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
