| Age | Commit message (Collapse) | Author |
|---|
|
For all cpuidle drivers that use CPUIDLE_FLAG_RCU_IDLE, ensure that
all functions that call ct_cpuidle_enter() are marked __cpuidle.
( due to lack of noinstr validation on these platforms it is entirely
possible this isn't complete )
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230112195542.274096325@infradead.org
|
|
OMAP3 uses full SoC suspend modes as idle states, as such it needs the
whole power-domain and clock-domain code from the idle path.
All that code is not suitable to run with RCU disabled, as such push
RCU-idle deeper still.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20230112195541.599561742@infradead.org
|
|
arch_cpu_idle() is a very simple idle interface and exposes only a
single idle state and is expected to not require RCU and not do any
tracing/instrumentation.
As such, omap_sram_idle() is not a valid implementation. Replace it
with the simple (shallow) omap3_do_wfi() call. Leaving the more
complicated idle states for the cpuidle driver.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20230112195541.538053457@infradead.org
|
|
We can now switch over to using cpu_pm instead of custom calls and make
the context save and restore functions static.
Let's also move the save and restore functions to avoid adding forward
declarations for them. And get rid of the static data pointer while at it.
Cc: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210727101034.32148-2-tony@atomide.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/soc
One more SoC change for omaps for v5.10 merge window
Remove debugfs dependency for enabling off mode during idle
for omap3 by enabling it automatically based on the PMIC
configuration.
* tag 'omap-for-v5.10/soc-part2-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: omap3: enable off mode automatically
Link: https://lore.kernel.org/r/pull-1601445968-476435@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Enabling off mode was only reachable deeply hidden
in the debugfs. As powersaving is an important feature,
move the option out of its shady place.
The debugfs file can still be used to override the default.
Use the presence of a device compatible to ti,twl4030-idle or
ti,twl4030-idle-osc-off as an indicator that the board is wired correctly
for off mode.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
[tony@atomide.com: updated to fix a checkpatch warning]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Remove trace_cpu_idle() from the arch_cpu_idle() implementations and
put it in the generic code, right before disabling RCU. Gets rid of
more trace_*_rcuidle() users.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Marco Elver <elver@google.com>
Link: https://lkml.kernel.org/r/20200821085348.428433395@infradead.org
|
|
We need to check for errors when calling cpu_pm_enter() and
cpu_cluster_pm_enter(). And we need to bail out on errors as
otherwise we can enter a deeper idle state when not desired.
I'm not aware of the lack of error handling causing issues yet,
but we need this at least for blocking deeper idle states when
a GPIO instance has pending interrupts.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20200304225433.37336-2-tony@atomide.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
With old DMA code disabled for handling DMA requests for device tree based
SoCs, we can move omap3 specific context save and restore to the dmaengine
driver.
Let's do this by adding cpu_pm notifier handling to save and restore context,
and enable it based on device tree match data. This way we can use the match
data later to configure more SoC specific features later on too.
Note that we only clear the channels in use while the platform code also
clears reserved channels 0 and 1 on high-security SoCs. Based on testing
on n900, this is not needed though and the system idles just fine.
With the dmaengine driver handling context save and restore, we must now
remove the old custom calls for context save and restore.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Vinod Koul <vkoul@kernel.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For a long time the gpio-omap custom PM calls have been annoying me so
let's replace them with cpu_pm instead. This will enable GPIO PM for
deeper idle states on omap4. And we can handle GPIO PM for omap2/3/4
in the same way.
Note that with this patch we are also slightly changing GPIO PM to be
less aggressive for omap3 and only will idle GPIO when PER context
may be lost.
For omap2, we don't need to save context and don't want to remove any
triggering so let's add a quirk flag for that.
Let's do this all in a single patch to avoid a situation where old
custom calls still are used with new code.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
With the CMA changes from Joonsoo Kim <iamjoonsoo.kim@lge.com>, it
was noticed that n900 stopped booting. After investigating it turned
out that n900 save_secure_ram_context does some whacky virtual to
physical address translation for the SRAM data address.
As we now only have minimal parts of omap3 idle code copied to SRAM,
running save_secure_ram_context() in SRAM is not needed. It only gets
called on PM init. And it seems there's no need to ever call this from
SRAM idle code.
So let's just keep save_secure_ram_context() in DDR, and pass it the
physical address of the parameters. We can do everything else in
omap-secure.c like we already do for other secure code.
And since we don't have any documentation, I still have no clue what
the values for 0, 1 and 1 for the parameters might be. If somebody has
figured it out, please do send a patch to add some comments.
Debugged-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Shared interrupts with IRQ_NOAUTOEN got a warning added with commit
04c848d39879 ("genirq: Warn when IRQ_NOAUTOEN is used with shared
interrupts").
Let's just drop the IRQ_NOAUTOEN use for omap3 PRM shared interrupt as
it does not seem to cause any other issues based on my testing. We have
moved a lot of the code to initialize later, and whatever problems the
legacy booting had seem to be gone now with pinctrl driver and device
tree based booting.
Otherwise we will get:
WARNING: CPU: 0 PID: 1 at kernel/irq/manage.c:1348 __setup_irq+0x5d0/0x64c
[<c01b0260>] (__setup_irq) from [<c01b0480>]
(request_threaded_irq+0xdc/0x188)
[<c01b0480>] (request_threaded_irq) from [<c051c780>]
(pcs_probe+0x6ec/0x8a4)
[<c051c780>] (pcs_probe) from [<c05a84b8>] (platform_drv_probe+0x50/0xb0)
[<c05a84b8>] (platform_drv_probe) from [<c05a6288>]
(driver_probe_device+0x33c/0x478)
Note that we also need to remove the related enable_irq() to avoid
getting the following:
WARNING: CPU: 0 PID: 1 at kernel/irq/manage.c:529 enable_irq+0x34/0x70
[<c01afa04>] (enable_irq) from [<c0c0f1fc>] (omap3_pm_init+0x118/0x3f8)
[<c0c0f1fc>] (omap3_pm_init) from [<c0c0ae7c>] (am35xx_init_late+0x10/0x18)
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Depending on timing during the resume path from off mode on 36xx, we may
see external aborts. These seem to be caused by the following:
- OMAP3 Advisory 1.62 "MPU Cannot Exit from Standby" says we need to
disable intc autoidle before WFI
- DM3730 Advisory 1.106 "MPU Leaves MSTANDBY State Before IDLEREQ of
Interrupt Controller is Released" says we need to wait before
accessing intc
omap3_intc_resume_idle restores the intc autoidle for all resume paths,
however in the resume path from off mode only it is also being restored
by omap_intc_restore_context before this call to omap3_intc_resume_idle
happens. The second restore of the intc autoidle in this path is what
appears to be causing the external abort so for the off mode resume path
let's rely on omap_intc_restore_context to restore intc autoidle, and
for all other paths let omap3_intc_resume_idle handle it as it is now.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The cpuidle tracepoints are called within a rcu_idle_exit() section, and
must be denoted with the _rcuidle() version of the tracepoint.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
OMAP2/3 now use generic API for the prm_clear_mod_irqs, the SoC specific
implementation details are provided through prm_ll_data.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
This makes the API the same as used with OMAP2, and makes it possible
to implement a generic driver API for the functionality.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
We still need to support platform data for omap3 until it's booting
in device tree only mode. So let's add platform_data/omap-gpmc.h for
that, and a minimal linux/omap-gpmc.h for the save and restore used
by the PM code.
Let's also keep a minimal mach-omap2/gpmc.h still around to avoid
churn on the board-*.c files. Once omap3 boots in device tree only
mode, we can drop mach-omap2/gpmc.h and we can make the data
structures in platform_data/omap-gpmc.h private to the GPMC driver.
Note that we can now also remove gpmc-nand.h and gpmc-onenand.h.
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Use the more common pr_warn.
Other miscellanea:
o Realign arguments
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Control module related PM initializations are now moved within control
module driver. Done in preparation to isolate the code to its own driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Done in preparation to move PRM into its own driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
This patch moves the functionality from PM core to control driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Helps to isolate the PRM driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
This is a more proper isolation of the code. Done in preparation of making
PRM an individual driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
This is a more proper isolation of the code. Done in preparation of making
PRM an individual driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Done in preparation to make the prm an individual driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Merge "ARM: omap pm changes for v3.16 merge window, resend" from Tony Lindgren:
PM related fixes for omap3 that were discovered during omap3
conversion to device tree. This series sets up the PMIC signaling
in a way where we can test for PM regressions easily by
looking at state of the the sys_clkreq and sys_off_mode pins.
Note that this series alone does not make omap3 PM to cut
off core voltage during off-idle, changes to twl4030-power.c
configurations are still needed. Those will be posted
separately.
* tag 'omap-for-v3.16/pm-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Enable CPUidle in omap2plus_defconfig
ARM: dts: Enable N900 keyboard sleep leds by default
ARM: OMAP2+: Fix voltage scaling init for device tree
ARM: dts: Configure omap3 twl4030 I2C4 pins by default
ARM: OMAP3: Fix voltage control for deeper idle states
ARM: OMAP3: Disable broken omap3_set_off_timings function
ARM: OMAP3: Fix idle mode signaling for sys_clkreq and sys_off_mode
ARM: dts: Fix omap serial wake-up when booted with device tree
mfd: twl-core: Fix idle mode signaling for omaps when booted with device tree
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
In omap2_common_pm_late_init suspend_set_ops was called to set common
suspend handling functions for all omap platforms. This created two
problems. First, these suspend ops were being set for all platforms,
regardless of whether or not suspend support has been integrated so in
the case of AM33XX, suspend to mem was presented as available but
failed every time. Second, some platforms will need to define a
completely separate set of suspend ops, such as AM33XX, due to
differences from previous omap platforms so there is no need to
always set the common omap ops.
This patch moves the suspend_set_ops call from omap2_common_pm_late_init
into a separate function that then gets called in the omap*_pm_init
functions for each platform.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
While debugging legacy mode vs device tree booted PM regressions,
I noticed that omap3 is not toggling sys_clkreq and sys_off_mode
pins like it should.
The sys_clkreq and sys_off_mode pins are not toggling because of
the following issues:
1. The default polarity for the sys_off_mode pin is wrong.
OFFMODE_POL needs to be cleared for sys_off_mode to go down when
hitting off-idle, while CLKREQ_POL needs to be set so sys_clkreq
goes down when hitting retention.
2. The values for voltctrl register need to be updated dynamically.
We need to set either the retention idle bits, or off idle bits
in the voltctrl register depending the idle mode we're targeting
to hit.
Let's fix these two issues as otherwise the system will just
hang if any twl4030 PMIC idle scripts are loaded. The only case
where the system does not hang is if only retention idle over I2C4
is configured by the bootloader.
Note that even without the twl4030 PMIC scripts, these fixes will
do the proper signaling of sys_clkreq and sys_off_mode pins, so
the fixes are needed to fix monitoring of PM states with LEDs or
an oscilloscope.
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
There is a solitary write to this register every wakeup from off-mode,
which isn't doing anything, so remove it.
Also note that modifying this register trashes any attempted
voltage scaling configuration and the change probably should
never have gotten merged in the first place.
Cc: Nishanth Menon <nm@ti.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[tony@atomide.com: updated comments to describe regression]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Some omap3 code is throwing a warning:
arch/arm/mach-omap2/pm34xx.c: In function 'omap3_save_secure_ram_context':
arch/arm/mach-omap2/pm34xx.c:123:32: warning: cast to pointer from
integer of different size [-Wint-to-pointer-cast]
In reality this code will never actually execute with LPAE=y, since
Cortex-A8 doesn't support it. So downcasting the __pa() is safe in
this case.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
OMAP3 PM core requires IVA2 bootmode to be set to idle during init. Currently,
a direct register write is used for this. Add a new ctrl API for this purpose
instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Commit a819c4f1 (ARM: OMAP3: PM: Only access IVA if one exists)
changed PM to not access IVA registers on omaps that don't have
them. Turns out we still need to idle iva2 as otherwise
iva2_pwrdm will stay on and block deeper idle states.
It seems that the only part of the reset that may not be needed
is the setting of the iva2 boot mode to idle. But as that register
seems to be there and is harmless if no iva2 is on the SoC, it's
probably safest to do the complete reset.
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
On OMAP platform, FIQ is reserved for secure environment only. If at all
the FIQ needs to be disabled, it involves going through security
API call. Hence the local_fiq_[enable/disable]() in the OMAP code is bogus.
On GP devices too, the fiq is disabled for non-secure software.
So just get rid of it.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
The text in Documentation said it would be removed in 2.6.41;
the text in the Kconfig said removal in the 3.1 release. Either
way you look at it, we are well past both, so push it off a cliff.
Note that the POWER_CSTATE and the POWER_PSTATE are part of the
legacy tracing API. Remove all tracepoints which use these flags.
As can be seen from context, most already have a trace entry via
trace_cpu_idle anyways.
Also, the cpufreq/cpufreq.c PSTATE one is actually unpaired, as
compared to the CSTATE ones which all have a clear start/stop.
As part of this, the trace_power_frequency also becomes orphaned,
so it too is deleted.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Based on earlier discussions[1] we attempted to find a suitable
location for the omap DMA header in commit 2b6c4e73 (ARM: OMAP:
DMA: Move plat/dma.h to plat-omap/dma-omap.h) until the conversion
to dmaengine is complete.
Unfortunately that was before I was able to try to test compile
of the ARM multiplatform builds for omap2+, and the end result
was not very good.
So I'm creating yet another all over the place patch to cut the
last dependency for building omap2+ for ARM multiplatform. After
this, we have finally removed the driver dependencies to the
arch/arm code, except for few drivers that are being worked on.
The other option was to make the <plat-omap/dma-omap.h> path
to work, but we'd have to add some new header directory to for
multiplatform builds.
Or we would have to manually include arch/arm/plat-omap/include
again from arch/arm/Makefile for omap2+.
Neither of these alternatives sound appealing as they will
likely lead addition of various other headers exposed to the
drivers, which we want to avoid for the multiplatform kernels.
Since we already have a minimal include/linux/omap-dma.h,
let's just use that instead and add a note to it to not
use the custom omap DMA functions any longer where possible.
Note that converting omap DMA to dmaengine depends on
dmaengine supporting automatically incrementing the FIFO
address at the device end, and converting all the remaining
legacy drivers. So it's going to be few more merge windows.
[1] https://patchwork.kernel.org/patch/1519591/#
cc: Russell King <linux@arm.linux.org.uk>
cc: Kevin Hilman <khilman@ti.com>
cc: "Benoît Cousson" <b-cousson@ti.com>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: "David S. Miller" <davem@davemloft.net>
cc: Vinod Koul <vinod.koul@intel.com>
cc: Dan Williams <djbw@fb.com>
cc: Mauro Carvalho Chehab <mchehab@infradead.org>
cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
cc: David Woodhouse <dwmw2@infradead.org>
cc: Kyungmin Park <kyungmin.park@samsung.com>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
cc: Hans Verkuil <hans.verkuil@cisco.com>
cc: Vaibhav Hiremath <hvaibhav@ti.com>
cc: Lokesh Vutla <lokeshvutla@ti.com>
cc: Rusty Russell <rusty@rustcorp.com.au>
cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
cc: Afzal Mohammed <afzal@ti.com>
cc: linux-crypto@vger.kernel.org
cc: linux-media@vger.kernel.org
cc: linux-mtd@lists.infradead.org
cc: linux-usb@vger.kernel.org
cc: linux-fbdev@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
omap-for-v3.8/cleanup-headers-prepare-multiplatform-v3
omap prcm changes via Paul Walmsley <paul@pwsan.com>:
Some miscellaneous OMAP hwmod changes for 3.8, along with a PRM
change needed for one of the hwmod patches to function.
Basic test logs for this branch on top of Tony's
omap-for-v3.8/clock branch at commit
558a0780b0a04862a678f7823215424b4e5501f9 are here:
http://www.pwsan.com/omap/testlogs/hwmod_devel_a_3.8/20121121161522/
However, omap-for-v3.8/clock at 558a0780 does not include some fixes
that are needed for a successful test. With several reverts,
fixes, and workarounds applied, the following test logs were
obtained:
http://www.pwsan.com/omap/testlogs/TEST_hwmod_devel_a_3.8/20121121162719/
which indicate that the series tests cleanly.
Conflicts:
arch/arm/mach-omap2/cm33xx.c
arch/arm/mach-omap2/io.c
arch/arm/mach-omap2/prm_common.c
|
|
|
|
|
|
arch/arm/mach-omap2/prcm.c and arch/arm/plat-omap/include/plat/prcm.h
are now completely unused and can be removed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
|
|
Most of the defines are specific to omap1 and omap2+,
and should be in the local headers. Only minimal function
prototypes need to be shared.
As discussed on linux-arm-kernel, we want to avoid
relative includes for the arch/arm/*omap* shared code:
http://www.spinics.net/lists/linux-omap/msg80520.html
So this patch re-adds a minimal plat/sram.h.
The new plat/sram.h must not be included from drivers,
that will break build for omap2+ CONFIG_MULTIPLATFORM.
Note that this patch temporarily adds two more
relative includes; Those will be removed in the
following patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.8/cleanup-prcm
The first set of OMAP PRM/CM-related cleanup patches for 3.8.
Prepares for the future move of the PRM/CM code to drivers/. Also
includes some prcm.[ch] cleanup patches from the WDTIMER cleanup
series that don't need external acks.
Basic test logs for this branch on top of v3.7-rc2 are here:
http://www.pwsan.com/omap/testlogs/prcm_cleanup_a_3.8/20121021123719/
But due to the number of unrelated regressions present in v3.7-rc[12],
it's not particularly usable as a testing base. With reverts, fixes,
and workarounds applied as documented in:
http://www.pwsan.com/omap/testlogs/test_v3.7-rc2/20121020134755/README.txt
the following test logs were obtained:
http://www.pwsan.com/omap/testlogs/prcm_cleanup_a_3.8/20121020231757/
which indicate that the series tests cleanly.
Conflicts:
arch/arm/mach-omap2/Makefile
arch/arm/mach-omap2/clockdomain2xxx_3xxx.c
arch/arm/mach-omap2/pm24xx.c
|
|
On OMAP34xx/35xx, and OMAP36xx chips with ES < 1.2, if the PER
powerdomain goes to OSWR or OFF while CORE stays at CSWR or ON, or if,
upon chip wakeup from OSWR or OFF, the CORE powerdomain goes ON before
PER, the UART3/4 FIFOs and McBSP2/3 SIDETONE memories will be
unusable. This is erratum i582 in the OMAP36xx Silicon Errata
document.
This patch implements one of several parts of the workaround: the
addition of the wakeup dependency between the PER and WKUP
clockdomains, such that PER will wake up at the same time CORE_L3
does.
This is not a complete workaround. For it to be complete:
1. the PER powerdomain's next power state must not be set to OSWR or
OFF if the CORE powerdomain's next power state is set to CSWR or
ON;
2. the UART3/4 FIFO and McBSP2/3 SIDETONE loopback tests should be run
if the LASTPOWERSTATEENTERED bits for PER and CORE indicate that
PER went OFF while CORE stayed on. If loopback tests fail, then
those devices will be unusable until PER and CORE can undergo a
transition from ON to OSWR/OFF and back ON.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Move OMAP3xxx-specific CM functions & macros into cm3xxx.[ch] and
OMAP2xxx-specific macros into cm2xxx.[ch]. Move basic CM register
access functions into static inline functions in cm2xxx_3xxx.h,
leaving only OMAP2/3 hardreset functions in cm2xxx_3xxx.c.
As part of this, split the CM and hwmod code that waits for devices to
become ready into SoC-specific functions.
This is in preparation for the upcoming move of this code to drivers/.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
Move OMAP3xxx-specific PRM functions & macros into prm3xxx.[ch] and
OMAP2xxx-specific macros into prm2xxx.h. (prm2xxx.c will be created
by a subsequent patch when it's needed.) Move basic PRM register
access functions into static inline functions in prm2xxx_3xxx.h, leaving
only OMAP2/3 hardreset functions in prm2xxx_3xxx.c.
Also clarify the initcall function naming to reinforce that this code
is specifically for the PRM IP block.
This is in preparation for the upcoming powerdomain series and the
upcoming move of this code to drivers/.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
We want to remove plat/cpu.h. To do this, let's first split
it to private soc.h to mach-omap1 and mach-omap2. We have to
keep plat/cpu.h around until the remaining drivers are fixed,
so let's include the local soc.h in plat/cpu.h and for drivers
still including plat/cpu.h.
Once the drivers are fixed not to include plat/cpu.h, we
can remove the file.
This is needed for the ARM common zImage support.
[tony@atomide.com: updated to not print a warning]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can move this from plat to be local to plat-omap
for common ARM zImage support.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
omap-for-v3.8/cleanup-headers
Conflicts:
arch/arm/mach-omap2/board-omap3logic.c
arch/arm/mach-omap2/gpmc.c
drivers/media/platform/omap/omap_vout.c
drivers/media/platform/omap/omap_vout_vrfb.c
|
|
omap-for-v3.8/cleanup-headers
Conflicts:
arch/arm/mach-omap2/board-3430sdp.c
arch/arm/mach-omap2/board-h4.c
arch/arm/mach-omap2/board-rx51-peripherals.c
arch/arm/mach-omap2/board-rx51.c
arch/arm/mach-omap2/pm34xx.c
drivers/mtd/nand/omap2.c
drivers/mtd/onenand/omap2.c
|
|
Remove arch/arm/plat-omap/include/plat/sdrc.h by folding its contents
into arch/arm/mach-omap2/sdrc.h. The objective is to assist Tony in
cleaning out arch/arm/plat-omap/, as his upstreams request.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
[tony@atomide.com: updated to remove rotate macros]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
