| Age | Commit message (Collapse) | Author |
|---|
|
Linux 3.5-rc6
Dependency for imx/soc changes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
A few more OMAP fixes for 3.5-rc. These fix some bugs with power
management and McBSP.
|
|
The commit 503d0ea24d1d3dd3db95e5e0edd693da7a2a23eb
ARM: OMAP4: hwmod data: Add aliases for McBSP fclk clocks
added a wrong "prcm_clk" alias for PRCM clock whereas the McBSP
driver and previous OMAPs are using "prcm_fck".
It thus lead to the following warning.
[ 47.409729] omap-mcbsp: clks: could not clk_get() prcm_fck
Fix that by changing the opt_clk role to prcm_fck.
Reported-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Sebastien Guiriec <s-guiriec@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
aess IP blocks
The OMAP4 usb_host_fs (OHCI) and AESS IP blocks require some special
programming for them to enter idle. Without this programming, they
will prevent the rest of the chip from entering full chip idle.
To implement the idle programming cleanly, this will take some
coordination between maintainers. This is likely to take some time,
so it is probably best to leave this for 3.6 or 3.7. So, in the
meantime, prevent these IP blocks from being registered.
Later, once the appropriate support is available, this patch can be
reverted.
This second version comments out the IP block data since Benoît didn't
like removing it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
From Tony Lindgren <tony@atomide.com>:
Here are changes to add support for am33xx processors for the
clock, power, and voltagedomains.
* tag 'omap-devel-am33xx-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP AM33xx: clockdomains: Add clockdomain data and respective operations
ARM: OMAP AM33xx: powerdomains: add AM335x support
ARM: OMAP AM33xx: CM: Introduce AM33xx CM APIs and register level details
ARM: OMAP AM33xx: PRM: add PRM support
ARM: OMAP AM33xx: voltagedomain: Add voltage domain data
ARM: OMAP2+: control: Add AM33XX control reg & sec clkctrl offset
ARM: OMAP2+: am33xx: Add AM335XEVM machine support
ARM: OMAP2+: am33xx: Add low level debugging support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The SYS_NIRQ1 pin is the interupt line for the PMIC part of the TWL6030
and interrupts from the PMIC are needed as wakeup sources.
Ensure this pin is mux'd as input and has wakeup enabled so PMIC
interupts (e.g. RTC) can be used as wakeup sources.
Tested on OMAP4430/Panda.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
In order for suspend/resume dependencies to work correctly, I2C has to
be initialized (more specifically, registered with the driver core)
before MMC. Without this, the MMC driver fails to adjust the VMMC
regulator (using i2c writes) during the suspend path.
Problem found testing suspend/resume on 3730/OveroSTORM platform.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
OMAP4470 currently fails to boot, printing various messages such as ...
omap_hwmod: mpu: cannot clk_get main_clk dpll_mpu_m2_ck
omap_hwmod: mpu: cannot _init_clocks
------------[ cut here ]------------
WARNING: at arch/arm/mach-omap2/omap_hwmod.c:2062 _init+0x2a0/0x2e4()
omap_hwmod: mpu: couldn't init clocks
Modules linked in:
[<c001c7fc>] (unwind_backtrace+0x0/0xf4) from [<c0043c64>] (warn_slowpath_common+0x4c/0x64)
[<c0043c64>] (warn_slowpath_common+0x4c/0x64) from [<c0043d10>] (warn_slowpath_fmt+0x30/0x40)
[<c0043d10>] (warn_slowpath_fmt+0x30/0x40) from [<c0674208>] (_init+0x2a0/0x2e4)
[<c0674208>] (_init+0x2a0/0x2e4) from [<c067428c>] (omap_hwmod_setup_one+0x40/0x60)
[<c067428c>] (omap_hwmod_setup_one+0x40/0x60) from [<c0674280>] (omap_hwmod_setup_one+0x34/0x60)
[<c0674280>] (omap_hwmod_setup_one+0x34/0x60) from [<c06726f4>] (omap_dm_timer_init_one+0x30/0x250)
[<c06726f4>] (omap_dm_timer_init_one+0x30/0x250) from [<c0672930>] (omap2_gp_clockevent_init+0x1c/0x108)
[<c0672930>] (omap2_gp_clockevent_init+0x1c/0x108) from [<c0672c60>] (omap4_timer_init+0x10/0x5c)
[<c0672c60>] (omap4_timer_init+0x10/0x5c) from [<c066c418>] (time_init+0x20/0x30)
[<c066c418>] (time_init+0x20/0x30) from [<c0668814>] (start_kernel+0x1b0/0x304)
[<c0668814>] (start_kernel+0x1b0/0x304) from [<80008044>] (0x80008044)
---[ end trace 1b75b31a2719ed1c ]---
The problem is that currently none of the clocks are being registered for
OMAP4470 devices and so on boot-up no clocks can be found and the kernel panics.
This fix allows the kernel to boot without failure using a simple RAMDISK file
system on OMAP4470 blaze board.
Per feedback from Paul and Benoit the 4470 clock data is incomplete for new
modules such as the 2D graphics block that has been added to the 4470.
Therefore add a warning to indicate that the clock data is incomplete.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
commit 8259573b (ARM: OMAP2+: nand: Make board_onenand_init() visible
to board code) broke the build for configs with OneNAND disabled. By
removing the static in the header file, it created a duplicate definition
in the .c and the .h files, resuling in a build error:
/work/kernel/omap/dev/arch/arm/mach-omap2/board-flash.c:102:111: error: redefinition of 'board_onenand_init'
/work/kernel/omap/dev/arch/arm/mach-omap2/board-flash.h:56:51: note: previous definition of 'board_onenand_init' was here
make[2]: *** [arch/arm/mach-omap2/board-flash.o] Error 1
make[2]: *** Waiting for unfinished jobs....
make[1]: *** [arch/arm/mach-omap2] Error 2
make: *** [sub-make] Error 2
Fix this by removing the duplicate dummy entry from the C file.
Cc: Enric Balletbò i Serra <eballetbo@gmail.com>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
From Paul Walmsley (as per Tony Lindgren's request):
"Some uncontroversial OMAP clock, hwmod, and compiler warning fixes for 3.5-rc"
* tag 'omap-fixes-a-for-3.5rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: OMAP4: hwmod data: Force HDMI in no-idle while enabled
ARM: OMAP2+: mux: fix sparse warning
ARM: OMAP2+: CM: increase the module disable timeout
ARM: OMAP4: clock data: add clockdomains for clocks used as main clocks
ARM: OMAP4: hwmod data: fix 32k sync timer idle modes
ARM: OMAP4+: hwmod: fix issue causing IPs not going back to Smart-Standby
ARM: OMAP: PM: Lock clocks list while generating summary
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
"Here are a few fixes with the biggest one being fix for Beagle DVI
reset. All of them are regression fixes, except for the missing omap2
interrupt controller binding that somehow got missed earlier."
* tag 'omap-fixes-for-v3.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: Fix Beagleboard DVI reset gpio
arm/dts: OMAP2: Fix interrupt controller binding
ARM: OMAP2: Fix tusb6010 GPIO interrupt for n8x0
ARM: OMAP2+: Fix MUSB ifdefs for platform init code
|
|
As per the OMAP4 documentation, audio over HDMI must be transmitted in
no-idle mode. This patch adds the HWMOD_SWSUP_SIDLE so that omap_hwmod uses
no-idle/force-idle settings instead of smart-idle mode.
This is required as the DSS interface clock is used as functional clock
for the HDMI wrapper audio FIFO. If no-idle mode is not used, audio could
be choppy, have bad quality or not be audible at all.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
[b-cousson@ti.com: Update the subject and align the .flags
location with the script template]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Commit bbd707acee279a61177a604822db92e8164d00db ("ARM: omap2: use
machine specific hook for late init") resulted in the addition of this
sparse warning:
arch/arm/mach-omap2/mux.c:791:12: warning: symbol 'omap_mux_late_init' was not declared. Should it be static?
Fix by including the header file containing the prototype.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Tony Lindgren <tony@atomide.com>
|
|
Increase the timeout for disabling an IP block to five milliseconds.
This is to handle the usb_host_fs idle latency, which takes almost
four milliseconds after a host controller reset.
This is the second of two patches needed to resolve the following
boot warning:
omap_hwmod: usb_host_fs: _wait_target_disable failed
Thanks to Sergei Shtylyov <sshtylyov@mvista.com> for finding
an unrelated hunk in a previous version of this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Tero Kristo <t-kristo@ti.com>
|
|
Until the OMAP4 code is converted to disable the use of the clock
framework-based clockdomain enable/disable sequence, any clock used as
a hwmod main_clk must have a clockdomain associated with it. This
patch populates some clock structure clockdomain names to resolve the
following warnings during kernel init:
omap_hwmod: dpll_mpu_m2_ck: missing clockdomain for dpll_mpu_m2_ck.
omap_hwmod: trace_clk_div_ck: missing clockdomain for trace_clk_div_ck.
omap_hwmod: l3_div_ck: missing clockdomain for l3_div_ck.
omap_hwmod: ddrphy_ck: missing clockdomain for ddrphy_ck.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
|
|
The 32k sync timer IP block target idle modes in the hwmod data are
incorrect. The IP block does not support any smart-idle modes.
Update the data to reflect the correct modes.
This problem was initially identified and a diff fragment posted to
the lists by Benoît Cousson <b-cousson@ti.com>. A patch description
bug in the first version was also identified by Benoît.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
|
|
If an IP is configured in Smart-Standby-Wakeup, when disabling wakeup feature the
IP will not go back to Smart-Standby, but will remain in Smart-Standby-Wakeup.
Signed-off-by: Djamil Elaidi <d-elaidi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Commit e813a55eb9c9bc6c8039fb16332cf43402125b30 ("OMAP: board-files:
remove custom PD GPIO handling for DVI output") moved TFP410 chip's
powerdown-gpio handling from the board files to the tfp410 driver. One
gpio_request_one(powerdown-gpio, ...) was mistakenly left unremoved in
the Beagle board file. This causes the tfp410 driver to fail to request
the gpio on Beagle, causing the driver to fail and thus the DVI output
doesn't work.
This patch removes several boot errors from board-omap3beagle.c:
- gpio_request: gpio--22 (DVI reset) status -22
- Unable to get DVI reset GPIO
There is a combination of leftover code and revision confusion.
Additionally, xM support is currently a hack.
For original Beagleboard this removes the double initialization of GPIO
170, properly configures it as an output, and wraps the initialization
in an if block so that xM does not attempt to request it.
For Beagleboard xM it removes reference to GPIO 129 which was part
of rev A1 and A2 designs, but never functioned. It then properly assigns
beagle_dvi_device.reset_gpio in beagle_twl_gpio_setup and removes the
hack of initializing it high. Additionally, it uses
gpio_set_value_cansleep since this GPIO is connected through i2c.
Unfortunately, there is no way to tell the difference between xM A2 and
A3. However, GPIO 129 does not function on rev A1 and A2, and the TWL
GPIO used on A3 and beyond is not used on rev A1 and A2, there are no
problems created by this fix.
Tested on Beagleboard-xM Rev C1 and Beagleboard Rev B4.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Here's one more gpio_to_irq conversion that we missed
earlier. Tested with n800 in gadget mode using USB_ETH.
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 62285963 (usb: musb: drop a gigantic amount of ifdeferry)
got rid of a bunch of ifdefs in the MUSB code. Looks like the
platform init code is still using these dropped defines though,
which in many cases results the board defaulting always to host
mode.
Currently the situation is that USB_MUSB_HDRC is the main
Kconfig option with additional USB_GADGET_MUSB_HDRC so only
these two should be used to select between host and OTG mode.
Fix the situation for omaps. The following users should fix the
platform init code in a similar way:
Dropped Kconfig option Current users
USB_MUSB_OTG blackfin, davinci, not in Kconfigs
USB_MUSB_PERIPHERAL davinci, not in Kconfigs
USB_MUSB_HOST davinci, not in Kconfigs
USB_MUSB_HDRC_HCD blackfin, not in Kconfigs
USB_MUSB_OTG blackfin, not in Kconfigs
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: linux-usb@vger.kernel.org
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
AM33XX PRCM module consists of various clockdomains, in all
total we have 18 clockdomains available, with following
controlling options,
- SW Sleep: sw forced sleep transition
- SW Wakeup: sw forced wakeup transition
This patch adds all available clockdomain data, respective
clockdomain operations for AM33XX family of device, and also
integrates it into existing OMAP framework.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
CC: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: removed CLKDM_NO_AUTODEPS from clockdomain flags, removed
unnecessary .clktrctrl_offs field; updated for 3.5]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Add offset & mask fields to struct powerdomain
In case of AM33xx family of devices, there is no consistency between
PWRSTCTRL & PWRSTST register offsers in PRM space, for example -
PRM_XXX PWRSTCTRL PWRSTST
=======================================
PRM_PER_MOD: 0x0C, 0x08
PRM_WKUP_MOD: 0x04, 0x08
PRM_MPU_MOD: 0x00, 0x04
PRM_DEVICE_MOD: NA, NA
And also, there is no consistency between bit-offsets inside
PWRSTCTRL & PWRSTST register, for example -
PRM_XXX LOGICRET MEMON MEMRET
=======================================
GFX_PWRCTRL: 2, 17, 6
PER_PWRCTRL: 3, 25, 29
MPU_PWRCTRL: 2, 18, 22
WKUP_PWRCTRL: 3, NA, NA
This means, we need to maintain and pass on all this information
in powerdomain handle; so adding fields for,
- PWRSTCTRL/ST register offset
- Logic retention state mask
- mem_on/ret/pwrst/retst mask
Currently, this fields is only applicable and used for AM33XX devices.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: this patch is a combination of "Add offset & mask fields to
struct powerdomain" and the powerdomain portions of "ARM: OMAP3+: am33xx:
Add powerdomain & PRM support"; updated for 3.5]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
As far as PRM/CM/PRCM modules are concerned, AM33XX device is
different than OMAP3 and OMAP4 architectures; so similar to
PRM implementation, handle AM33XX CM separately.
This patch introduces AM33XX CM module low-level api's, used and
required by omap clockdomain and hwmod framework.
Please note that cm-regbits-33xx.h (register bit field offset)
and cm33xx.h (register addr offset) files are mostly auto generated.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
CC: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: split the hwmod code changes in this patch into a separate
patch; updated for 3.5]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
As far as PRM/CM/PRCM modules are concerned, AM33XX device is
different than OMAP3 and OMAP4 architectures; so we need to handle it
separately. This patch adds support for the PRM APIs required for
AM33XX device.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: separated the PRM parts of "ARM: OMAP3+: am33xx: Add
powerdomain & PRM support" into this patch; fixed Makefile prm33xx.o
location; cleaned up some checkpatch violations; updated for 3.5]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Currently dummy voltage domain data is being created
in order to succeed boot process, nothing has been done
w.r.t actual hardware (voltage control).
Also, hook up the AM33XX voltage domain to OMAP framework.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
[paul@pwsan.com: updated for 3.5]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Define AM33XX control register, in order to allow access to
control register address space, also add CONTROL_SEC_CLK_CTRL
register offset; both are required in clock tree data,
for wdt0 and timer0 clock source select configuration.
CONTROL.SEC_CLK_CTRL register is provided to select/configure
clock input for WDT0 and TIMER0.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
[paul@pwsan.com: added include of plat/am33xx.h to fix build break;
added AM33XX_CONTROL_STATUS bitfields that will be needed for the clock
tree; fixed some control.h whitespace problems while here]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A bit larger set than usual, unfortunately -- I've been sitting on
them longer than I meant to so it's really more like 2 -rc pull
requests in one, volume-wise.
Nearly everything is fixes for fallout from the merge window, or other
fixes for bugs. The one exception is the highbank L2-enablement
patch, but it was contained enough that I picked it up anyway:
- i.MX fixes, mostly for clock and pinctrl changes
- OMAP fixes, mostly PM-related
- A patch to enable L2 on highbank
- A couple of fixes for PXA, Kirkwood, Versatile"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (30 commits)
ARM: Kirkwood: Fix clk problems modular ethernet driver
arm: versatile: fix and enable PCI I/O space
ARM: highbank: Add smc calls to enable/disable the L2
ARM i.MX imx21ads: Fix overlapping static i/o mappings
ARM: imx6: exit coherency when shutting down a cpu
ARM: mx51: Add pinctrl_provide_dummies()
ARM: mx31: Add pinctrl_provide_dummies()
ARM: OMAP2+: Fix compile for CONFIG_TIDSPBRIDGE platform init code
ARM: OMAP3: Fix omap3_l3_block_irq warning when CONFIG_BUG is not set
ARM: OMAP: Fix MMC_OMAP build when only MMC_OMAP_HS is selected
OMAP2+: UART: Add mechanism to probe uart pins and configure rx wakeup
ARM: mmp: fix missing cascade_irq in irq handler
ARM: dts: update memory size on brownstone
ARM i.MX27 Visstrim M10: fix gpio handling.
ARM i.MX53: Fix PLL4 base address
ARM i.MX pllv2: make round_rate accurate
ARM i.MX pllv2: use standard register set unconditionally
ARM: OMAP: Fix lis3lv02d accelerometer to use gpio_to_irq
ARM: imx: only call l2x0_init if it's available
ARM: imx: only specify i2c device type once
...
|
|
Pull omapdss build problem fix from Tomi Valkeinen:
"Small fixes for omapdss driver. Most importantly, fixes a build
problem when debugfs or omapdss debug support is turned off, and fixes
a suspend related crash."
This has apparently been annoying rmk for a while..
* tag 'omapdss-for-3.5-rc2' of git://gitorious.org/linux-omap-dss2/linux:
OMAPDSS: fix registration of DPI and SDI devices
OMAPDSS: DSI: Fix bug when calculating LP command interleaving parameters
OMAPDSS: fix bogus WARN_ON in dss_runtime_put()
OMAPDSS: Taal: fix compilation warning
OMAPDSS: fix build when DEBUG_FS or DSS_DEBUG_SUPPORT disabled
|
|
Commit 7f28427b (ARM: OMAP2+: Move omap_dsp_reserve_sdram_memblock() to mach-omap2)
moved DSP platform init code, but failed to include memblock.h causing:
arch/arm/mach-omap2/dsp.c: In function 'omap_dsp_reserve_sdram_memblock':
arch/arm/mach-omap2/dsp.c:58: error: implicit declaration of function 'arm_memblock_steal'
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Otherwise we will get:
arch/arm/mach-omap2/omap_l3_smx.c: In function ‘omap3_l3_block_irq’:
arch/arm/mach-omap2/omap_l3_smx.c:156: warning: unused variable ‘address’
arch/arm/mach-omap2/omap_l3_smx.c:155: warning: unused variable ‘multi’
arch/arm/mach-omap2/omap_l3_smx.c:154: warning: unused variable ‘initid’
arch/arm/mach-omap2/omap_l3_smx.c:153: warning: unused variable ‘code’
arch/arm/mach-omap2/omap_l3_smx.c: At top level:
arch/arm/mach-omap2/omap_l3_smx.c:68: warning: ‘omap3_l3_code_string’ defined but not used
arch/arm/mach-omap2/omap_l3_smx.c:90: warning: ‘omap3_l3_initiator_string’ defined but not used
Fix it by always showing the L3 error.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The omapdss arch initialization code registers all the output devices as
omap_devices. However, DPI and SDI are not proper omap_devices, as they
do not have any corresponding HWMOD. This leads to crashes or problems
when the platform code tries to use omap_device functions for DPI and
SDI devices.
One such crash was reported by John Stultz <johnstul@us.ibm.com>:
[ 18.756835] Unable to handle kernel NULL pointer dereference at
virtual addr8
[ 18.765319] pgd = ea6b8000
[ 18.768188] [00000018] *pgd=aa942831, *pte=00000000, *ppte=00000000
[ 18.774749] Internal error: Oops: 17 [#1] SMP ARM
[ 18.779663] Modules linked in:
[ 18.782836] CPU: 0 Not tainted (3.5.0-rc1-dirty #456)
[ 18.788482] PC is at _od_resume_noirq+0x1c/0x78
[ 18.793212] LR is at _od_resume_noirq+0x6c/0x78
[ 18.797943] pc : [<c00307ec>] lr : [<c003083c>] psr: 20000113
[ 18.797943] sp : ec3abe80 ip : ec3abdb8 fp : 00000006
[ 18.809936] r10: ec1148b8 r9 : c08a48f0 r8 : c00307d0
[ 18.815368] r7 : 00000000 r6 : 00000000 r5 : ec114800 r4 :
ec114808
[ 18.822174] r3 : 00000000 r2 : 00000000 r1 : ec154fe8 r0 :
00000006
[ 18.829010] Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM
Segment user
[ 18.836456] Control: 10c5387d Table: aa6b804a DAC: 00000015
[ 18.842437] Process sh (pid: 1139, stack limit = 0xec3aa2f0)
[ 18.848358] Stack: (0xec3abe80 to 0xec3ac000)
DPI and SDI can be plain platform_devices. This patch changes the
registration from omap_device_register() to platform_device_add().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: John Stultz <johnstul@us.ibm.com>
Tested-by: Jean Pihet <jean.pihet@newoldbits.com>
|
|
The commit (bce492c0 ARM: OMAP2+: UART: Fix incorrect population of
default uart pads) removed default uart pads that where getting populated
and which was making rx pin wakeup capable. If uart pads were used in
different mode by any other module then it would fail since the default
pads took over all the uart pins forcefully. With removal of default pads
the rx_pad wakeup for console uart while waking up from off mode is broken.
Utilise the mux api available to probe the availability of mux pins
in uart mode and probe for availability of uart pin in mux mode0
if uart is available as uart pin itself then configure rx pin
as wakeup capable.
This patch itself doesn't cater to all boards. Boards using uart rx wakeup
mechanism should ensure the usage of omap_serial_init_port by configuring
required uart ports and pass necessary mux data, till then this probing of
uart pins can cater to enabling of rx pad wakeup to most of the boards.
This patch can also throw some boot warning from _omap_mux_get_by_name
if pin is requested for availability is not present while dynamically probing
the uart pins availability such boot warnings can be addressed only when board
files are patched with omap_serial_init_port calls passing the right pads
needed for a given port.
Discussion Threads for reference:
http://www.spinics.net/lists/linux-omap/msg69859.html
http://www.spinics.net/lists/linux-omap/msg68659.html
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Russ Dill <russ.dill@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Ameya Palande <ameya.palande@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
[tony@atomide.com: updated to fix compile when CONFIG_OMAP_MUX is not set]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch adds minimal support for AM335X machine init.
During last merge window, two separate patches supporting am33xx
machine init had been submitted,
1. Link to earlier Baseport patch submission (Legacy):
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg59325.html
2. Link to earlier DT based machine init support patch submission:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg61398.html
And both had got accepted at that time, but got missed during
merge window.
But now, since we have taken decision to make am33xx as a separate
class and not to follow omap3 family, these patches needs to changes
accordingly (only changes),
- Combine both the patches, since early init and timer init
used in board-generic.c file requires them.
- Remove dependency on AM3517EVM, and only use DT approach
for machine init.
- Change the config option (as changed recently)
CONFIG_SOC_OMAPAM33XX --> CONFIG_SOC_AM33XX
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add support for low level debugging on AM335X EVM (AM33XX family).
Currently only support for UART1 console, which is used on AM335X EVM
is added.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 3b511201 (ARM: OMAP: rx51: Platform support for lis3lv02d accelerometer)
added support for lis3lv02d accelerometer.
The patch was still using OMAP_GPIO_IRQ which no longer exists.
Fix it by using gpio_to_irq().
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into fixes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into fixes
|
|
Pull fbdev updates from Florian Tobias Schandinat:
- driver for AUO-K1900 and AUO-K1901 epaper controller
- large updates for OMAP (e.g. decouple HDMI audio and video)
- some updates for Exynos and SH Mobile
- various other small fixes and cleanups
* tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6: (130 commits)
video: bfin_adv7393fb: Fix cleanup code
video: exynos_dp: reduce delay time when configuring video setting
video: exynos_dp: move sw reset prioir to enabling sw defined function
video: exynos_dp: use devm_ functions
fb: handle NULL pointers in framebuffer release
OMAPDSS: HDMI: OMAP4: Update IRQ flags for the HPD IRQ request
OMAPDSS: Apply VENC timings even if panel is disabled
OMAPDSS: VENC/DISPC: Delay dividing Y resolution for managers connected to VENC
OMAPDSS: DISPC: Support rotation through TILER
OMAPDSS: VRFB: remove compiler warnings when CONFIG_BUG=n
OMAPFB: remove compiler warnings when CONFIG_BUG=n
OMAPDSS: remove compiler warnings when CONFIG_BUG=n
OMAPDSS: DISPC: fix usage of dispc_ovl_set_accu_uv
OMAPDSS: use DSI_FIFO_BUG workaround only for manual update displays
OMAPDSS: DSI: Support command mode interleaving during video mode blanking periods
OMAPDSS: DISPC: Update Accumulator configuration for chroma plane
drivers/video: fsl-diu-fb: don't initialize the THRESHOLDS registers
video: exynos mipi dsi: support reverse panel type
video: exynos mipi dsi: Properly interpret the interrupt source flags
video: exynos mipi dsi: Avoid races in probe()
...
|
|
Pull mtd update from David Woodhouse:
- More robust parsing especially of xattr data in JFFS2
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
Fixed trivial conflict in drivers/mtd/nand/gpmi-nand/gpmi-nand.c due to
added include files next to each other.
* tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd: (75 commits)
mtd: mxc_nand: move ecc strengh setup before nand_scan_tail
mtd: block2mtd: fix recursive call of mtd_writev
mtd: gpmi-nand: define ecc.strength
mtd: of_parts: fix breakage in Kconfig
mtd: nand: fix scan_read_raw_oob
mtd: docg3 fix in-middle of blocks reads
mtd: cfi_cmdset_0002: Slight cleanup of fixup messages
mtd: add fixup for S29NS512P NOR flash.
jffs2: allow to complete xattr integrity check on first GC scan
jffs2: allow to discriminate between recoverable and non-recoverable errors
mtd: nand: omap: add support for hardware BCH ecc
ARM: OMAP3: gpmc: add BCH ecc api and modes
mtd: nand: check the return code of 'read_oob/read_oob_raw'
mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw'
mtd: m25p80: Add support for Winbond W25Q80BW
jffs2: get rid of jffs2_sync_super
jffs2: remove unnecessary GC pass on sync
jffs2: remove unnecessary GC pass on umount
jffs2: remove lock_super
mtd: gpmi: add gpmi support for mx6q
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull sweeping late_initcall cleanup for arm-soc from Olof Johansson:
"This is a patch series from Shawn Guo that moves from individual
late_initcalls() to using a member in the machine structure to invoke
a platform's late initcalls.
This cleanup is a step in the move towards multiplatform kernels since
it would reduce the need to check for compatible platforms in each and
every initcall."
Fix up trivial conflicts in arch/arm/mach-{exynos/mach-universal_c210.c,
imx/mach-cpuimx51.c, omap2/board-generic.c} due to changes nearby (and,
in the case of cpuimx51.c the board support being deleted)
* tag 'cleanup-initcall' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: ux500: use machine specific hook for late init
ARM: tegra: use machine specific hook for late init
ARM: shmobile: use machine specific hook for late init
ARM: sa1100: use machine specific hook for late init
ARM: s3c64xx: use machine specific hook for late init
ARM: prima2: use machine specific hook for late init
ARM: pnx4008: use machine specific hook for late init
ARM: omap2: use machine specific hook for late init
ARM: omap1: use machine specific hook for late init
ARM: msm: use machine specific hook for late init
ARM: imx: use machine specific hook for late init
ARM: exynos: use machine specific hook for late init
ARM: ep93xx: use machine specific hook for late init
ARM: davinci: use machine specific hook for late init
ARM: provide a late_initcall hook for platform initialization
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc cleanups (part 2) from Olof Johansson:
"More cleanups, continuing an earlier set with omap and samsung
specific cleanups. These could not go into the first set because they
have dependencies on various other series that in turn depend on the
first cleanups."
Fixed up conflicts in arch/arm/plat-omap/counter_32k.c due to commit
bd0493eaaf5c: "move read_{boot,persistent}_clock to the architecture
level" that changed how the persistent clocks were handled. And trivial
conflicts in arch/arm/mach-omap1/common.h due to just independent
changes close to each other.
* tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (35 commits)
ARM: SAMSUNG: merge plat-s5p into plat-samsung
ARM: SAMSUNG: move options for common s5p into plat-samsung/Kconfig
ARM: SAMSUNG: move setup code for s5p mfc and mipiphy into plat-samsung
ARM: SAMSUNG: move platform device for s5p uart into plat-samsung
ARM: SAMSUNG: move hr timer for common s5p into plat-samsung
ARM: SAMSUNG: move pm part for common s5p into plat-samsung
ARM: SAMSUNG: move interrupt part for common s5p into plat-samsung
ARM: SAMSUNG: move clock part for common s5p into plat-samsung
ARM: S3C24XX: Use common macro to define resources on dev-uart.c
ARM: S3C24XX: move common clock init into common.c
ARM: S3C24XX: move common power-management code to mach-s3c24xx
ARM: S3C24XX: move plat-s3c24xx/dev-uart.c into common.c
ARM: S3C24XX: move plat-s3c24xx/cpu.c
ARM: OMAP2+: Kconfig: convert SOC_OMAPAM33XX to SOC_AM33XX
ARM: OMAP2+: Kconfig: convert SOC_OMAPTI81XX to SOC_TI81XX
GPMC: add ECC control definitions
ARM: OMAP2+: dmtimer: remove redundant sysconfig context restore
ARM: OMAP: AM35xx: convert 3517 detection/flags to AM35xx
ARM: OMAP: AM35xx: remove redunant cpu_is checks for AM3505
ARM: OMAP1: Pass dma request lines in platform data to MMC driver
...
|
|
Use the more generic SoC family soc_is_am35xx() instead of the specific
cpu_is_omap3517() (which is being removed.)
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Mark A. Greer <mgreer@animalcreek.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Pull GPIO driver changes from Grant Likely:
"Lots of gpio changes, both to core code and drivers.
Changes do touch architecture code to remove the need for separate
arm/gpio.h includes in most architectures.
Some new drivers are added, and a number of gpio drivers are converted
to use irq_domains for gpio inputs used as interrupts. Device tree
support has been amended to allow multiple gpio_chips to use the same
device tree node.
Remaining changes are primarily bug fixes."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6: (33 commits)
gpio/generic: initialize basic_mmio_gpio shadow variables properly
gpiolib: Remove 'const' from data argument of gpiochip_find()
gpio/rc5t583: add gpio driver for RICOH PMIC RC5T583
gpiolib: quiet gpiochip_add boot message noise
gpio: mpc8xxx: Prevent NULL pointer deref in demux handler
gpio/lpc32xx: Add device tree support
gpio: Adjust of_xlate API to support multiple GPIO chips
gpiolib: Implement devm_gpio_request_one()
gpio-mcp23s08: dbg_show: fix pullup configuration display
Add support for TCA6424A
gpio/omap: (re)fix wakeups on level-triggered GPIOs
gpio/omap: fix broken context restore for non-OFF mode transitions
gpio/omap: fix missing check in *_runtime_suspend()
gpio/omap: remove cpu_is_omapxxxx() checks from *_runtime_resume()
gpio/omap: remove suspend/resume callbacks
gpio/omap: remove retrigger variable in gpio_irq_handler
gpio/omap: remove saved_wakeup field from struct gpio_bank
gpio/omap: remove suspend_wakeup field from struct gpio_bank
gpio/omap: remove saved_fallingdetect, saved_risingdetect
gpio/omap: remove virtual_irq_start variable
...
Conflicts:
drivers/gpio/gpio-samsung.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY updates from Greg Kroah-Hartman:
"Here's the big TTY/serial driver pull request for the 3.5-rc1 merge
window.
Nothing major in here, just lots of incremental changes from Alan and
Jiri reworking some tty core things to behave better and to get a more
solid grasp on some of the nasty tty locking issues.
There are a few tty and serial driver updates in here as well.
All of this has been in the linux-next releases for a while with no
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (115 commits)
serial: bfin_uart: Make MMR access compatible with 32 bits bf609 style controller.
serial: bfin_uart: RTS and CTS MMRs can be either 16-bit width or 32-bit width.
serial: bfin_uart: narrow the reboot condition in DMA tx interrupt
serial: bfin_uart: Adapt bf5xx serial driver to bf60x serial4 controller.
Revert "serial_core: Update buffer overrun statistics."
tty: hvc_xen: NULL dereference on allocation failure
tty: Fix LED error return
tty: Allow uart_register/unregister/register
tty: move global ldisc idle waitqueue to the individual ldisc
serial8250-em: Add DT support
serial8250-em: clk_get() IS_ERR() error handling fix
serial_core: Update buffer overrun statistics.
tty: drop the pty lock during hangup
cris: fix missing tty arg in wait_event_interruptible_tty call
tty/amiserial: Add missing argument for tty_unlock()
tty_lock: Localise the lock
pty: Lock the devpts bits privately
tty_lock: undo the old tty_lock use on the ctty
serial8250-em: Emma Mobile UART driver V2
Add missing call to uart_update_timeout()
...
|
|
Pull arm-soc board specific changes from Olof Johansson:
"While we generally attempt to get rid of board specific files and
replace them with device tree based descriptions, a lot of platforms
have not come that far:
In shmobile, we add two new board files because their recently started
effort to add DT support has not proceeded enough to use it for all of
the important hardware.
In Kirkwood, we are adding support for new boards with a combination
of DT and board file contents in multiple cases.
pxa/mmp and imx are extending support for existing board files but not
adding new ones."
Fix up trivial conflicts in arch/arm/mach-{mmp/ttc_dkb.c,shmobile/{Kconfig,Makefile}}
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
ARM: shmobile: fix smp build
ARM: kirkwood: Add support for RaidSonic IB-NAS6210/6220 using devicetree
kirkwood: Add iconnect support
orion/kirkwood: create a generic function for gpio led blinking
kirkwood/orion: fix orion_gpio_set_blink
ARM: kirkwood: Define DNS-320/DNS-325 NAND in fdt
kirkwood: Allow nand to be configured via. devicetree
mtd: Add orion_nand devicetree bindings
ARM: kirkwood: Basic support for DNS-320 and DNS-325
ARM: mach-shmobile: Use DT_MACHINE for armadillo 800 eva
ARM: mach-shmobile: Use DT_MACHINE for KZM9G
ARM: pxa: hx4700: Add Synaptics NavPoint touchpad
ARM: pxa: Use REGULATOR_SUPPLY macro
ARM: mach-shmobile: kzm9g: enable SMP boot
ARM: mach-shmobile: kzm9g: defconfig update
ARM: mach-shmobile: kzm9g: add PCF8757 gpio-key
ARM: mach-shmobile: kzm9g: add SDHI support
ARM: mach-shmobile: kzm9g: add MMCIF support
ARM: mach-shmobile: kzm9g: correct screen direction
ARM: mach-shmobile: sh73a0.h: add GPIO_NR
...
|
|
Pull arm-soc power management changes from Olof Johansson:
"Power management changes here are mostly for the omap platform, but
also include cpuidle changes for ux500 and suspend/resume code for
mmp."
* tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
ARM: OMAP2+: WDTIMER integration: fix !PM boot crash, disarm timer after hwmod reset
ARM: OMAP2/3: hwmod data: Add 32k-sync timer data to hwmod database
ARM: OMAP4: hwmod_data: Name the common irq for McBSP ports
ARM: OMAP4: hwmod data: I2C: add flag for context restore
ARM: OMAP3: hwmod_data: Rename the common irq for McBSP ports
ARM: OMAP2xxx: hwmod data: add HDQ/1-wire hwmod
ARM: OMAP3: hwmod data: add HDQ/1-wire hwmod
ARM: OMAP2+: hwmod data: add HDQ/1-wire hwmod shared data
ARM: OMAP2+: HDQ1W: add custom reset function
ARM: OMAP2420: hwmod data: Add MMC hwmod data for 2420
arm: omap3: clockdomain data: Remove superfluous commas from gfx_sgx_3xxx_wkdeps[]
ARM: OMAP2+: powerdomain: Get rid off duplicate pwrdm_clkdm_state_switch() API
ARM: OMAP3: clock data: add clockdomain for HDQ functional clock
ARM: OMAP3+: dpll: Configure autoidle mode only if it's supported
ARM: OMAP2+: dmtimer: cleanup iclk usage
ARM: OMAP4+: Add prm and cm base init function.
ARM: OMAP2/3: Add idle_st bits for ST_32KSYNC timer to prcm-common header
ARM: OMAP3: Fix CM register bit masks
ARM: OMAP: clock: convert AM3517/3505 detection/flags to AM35xx
ARM: OMAP3: clock data: treat all AM35x devices the same
...
|
|
Pull device tree conversions for arm-soc, part 1, from Olof Johansson:
"The spear3xx, lpc32xx, shmobile and mmp platforms are joining the game
of booting using device trees, which is a great step forward for them.
at91 and spear have pretty much completed this process with a huge
amount of work being put into at91. The other platforms are
continuing the process.
We finally start to see the payback on this investment, as new
machines are getting supported purely by adding a .dts source file
that can be completely independent of the kernel source."
Fix up trivial conflict in arch/arm/Kconfig
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: at91: Add ADC driver to at91sam9260/at91sam9g20 dtsi files
arm/dts: omap4-panda: Add LEDs support
arm/dts: omap4-sdp: Add LEDs support
arm/dts: twl4030: Add twl4030-gpio node
OMAP4: devices: Do not create mcpdm device if the dtb has been provided
OMAP4: devices: Do not create dmic device if the dtb has been provided
Documentation: update docs for mmp dt
ARM: dts: refresh dts file for arch mmp
ARM: mmp: support pxa910 with device tree
ARM: mmp: support mmp2 with device tree
gpio: pxa: parse gpio from DTS file
ARM: mmp: support DT in timer
ARM: mmp: support DT in irq
ARM: mmp: append CONFIG_MACH_MMP2_DT
ARM: mmp: fix build issue on mmp with device tree
ARM: ux500: Enable PRCMU Timer 4 (clocksource) for Device Tree
ARM: ux500: Disable SMSC911x platform code registration when DT is enabled
ARM: ux500: Fork cpu-db8500 platform_devs for sequential DT enablement
ARM: ux500: Do not attempt to register non-existent i2c devices on Snowball
ARM: SPEAr3xx: Correct keyboard data passed from DT
...
|
|
Pull non-critical arm-soc bug fixes from Olof Johansson:
"These bug fixes were not important enough to have them included in the
v3.4 release, mostly because they cover harmless warnings or
unrealistic configurations. Instead we queue them up to be picked up
in the next merge window."
Fixed up trivial conflict in arch/arm/mach-omap2/board-omap4panda.c
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: spear6xx: remove board selection options
ARM: OMAP: igep0020: Specify the VPLL2 regulator unconditionally
ARM: OMAP2+: INTC: fix Kconfig option for TI81XX
ARM: OMAP2+: remove incorrect irq_chip ack field
ARM: OMAP4: Adding ID for OMAP4460 ES1.1
ARM: OMAP4: panda: add statics to remove warnings
ARM: OMAP2+: Incorrect Register Offsets in OMAP Mailbox
ARM: OMAP: fix trivial warnings for dspbridge
arm: davinci: use for_each_set_bit_from
ARM: OMAP4: hsmmc: check for null pointer
ARM: OMAP1: fix compilation issue in board-sx1.c
ARM: disable SUSPEND/ARCH_SUSPEND_POSSIBLE for ARCH_TEGRA
ARM: davinci: da850-evm: fix section mismatch
ARM: tegra: add pll_x freq table entry for 750MHz
ARM: davinci: mark spi_board_info arguments as const
ARM: davinci: fix incorrect pdctl next bit position
|
|
Pull first batch of arm-soc cleanups from Olof Johansson:
"These cleanups are basically all over the place. The idea is to
collect changes with minimal impact but large number of changes so we
can avoid them from distracting in the diffstat in the other series.
A significant number of lines get removed here, in particular because
the ixp2000 and ixp23xx platforms get removed. These have never been
extremely popular and have fallen into disuse over time with no active
maintainer taking care of them. The u5500 soc never made it into a
product, so we are removing it from the ux500 platform.
Many good cleanups also went into the at91 and omap platforms, as has
been the case for a number of releases."
Trivial modify-delete conflicts in arch/arm/mach-{ixp2000,ixp23xx}
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (152 commits)
ARM: clps711x: Cleanup IRQ handling
ARM clps711x: Removed unused header mach/time.h
ARM: clps711x: Added note about support EP731x CPU to Kconfig
ARM: clps711x: Added missing register definitions
ARM: clps711x: Used own subarch directory for store header file
Dove: Fix Section mismatch warnings
ARM: orion5x: ts78xx debugging changes
ARM: orion5x: remove PM dependency from ts78xx
ARM: orion5x: ts78xx fix NAND resource off by one
ARM: orion5x: ts78xx whitespace cleanups
Orion5x: Fix Section mismatch warnings
Orion5x: Fix warning: struct pci_dev declared inside paramter list
ARM: clps711x: Combine header files into one for clps711x-targets
ARM: S3C24XX: Use common macro to define resources on mach-qt2410.c
ARM: S3C24XX: Use common macro to define resources on mach-osiris.c
ARM: EXYNOS: Adapt to cpuidle core time keeping and irq enable
ARM: S5PV210: Use common macro to define resources on mach-smdkv210.c
ARM: S5PV210: Use common macro to define resources on dev-audio.c
ARM: S5PC100: Use common macro to define resources on dev-audio.c
ARM: S5P64X0: Use common macro to define resources on dev-audio.c
...
|
|
git://git.infradead.org/users/jcooper/linux into next/boards
* 'kirkwood_boards_for_v3.5' of git://git.infradead.org/users/jcooper/linux:
ARM: kirkwood: Add support for RaidSonic IB-NAS6210/6220 using devicetree
kirkwood: Add iconnect support
orion/kirkwood: create a generic function for gpio led blinking
kirkwood/orion: fix orion_gpio_set_blink
ARM: kirkwood: Define DNS-320/DNS-325 NAND in fdt
kirkwood: Allow nand to be configured via. devicetree
mtd: Add orion_nand devicetree bindings
ARM: kirkwood: Basic support for DNS-320 and DNS-325
Includes an update to v3.4-rc7
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
