| Age | Commit message (Collapse) | Author |
|---|
|
Configure the clock controller to set an alternate clock for the CPU
when it receives an IRQ during LP1 (system suspend). Specifically, use
clk_m (the crystal) rather than clk_s (a 32KHz clock). Such an IRQ will
be the LP1 wake event. This reduces the amount of time taken to resume
from LP1.
NVIDIA's downstream kernel executes this code on both Tegra30 and
Tegra124, so it appears OK to make this change unconditionally.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The reshift hardware module implements the RAM re-repair process. This
module uses PLLP as an input clock during LP1 resume. The input divider
for this clock is typically set for PLLP's normal rate. During LP1
resume, PLLP is bypassed and so runs at the crystal rate, which is much
slower. Consequently, decrease the divider so that the reshift module
runs at a reasonable rate during LP1 resume.
NVIDIA's downstream kernel code only does this if not compiled for
Tegra30, so the added code is made conditional upon the chip ID.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
For a little over a year, U-Boot has configured the flow controller to
perform automatic RAM re-repair on off->on power transitions of the CPU
rail[1]. This is mandatory for correct operation of Tegra124. However,
RAM re-repair relies on certain clocks, which the kernel must enable and
leave running. PLLP is one of those clocks. This clock is shut down
during LP1 in order to save power. Enable bypass (which I believe routes
osc_div_clk, essentially the crystal clock, to the PLL output) so that
this clock signal toggles even though the PLL is not active. This is
required so that LP1 power mode (system suspend) operates correctly.
The bypass configuration must then be undone when resuming from LP1, so
that all peripheral clocks run at the expected rate. Without this, many
peripherals won't work correctly; for example, the UART baud rate would
be incorrect.
NVIDIA's downstream kernel code only does this if not compiled for
Tegra30, so the added code is made conditional upon the chip ID.
NVIDIA's downstream code makes this change conditional upon the active
CPU cluster. The upstream kernel currently doesn't support cluster
switching, so this patch doesn't test the active CPU cluster ID.
[1] 3cc7942a4ae5 ARM: tegra: implement RAM repair
Reported-by: Jonathan Hunter <jonathanh@nvidia.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Pull ARM SoC platform updates from Olof Johansson:
"Most of these are for MMP (seeing a bunch of cleanups and refactorings
for the first time in a while), and for OMAP (a bunch of cleanups and
added support for voltage controller on OMAP4430)"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (51 commits)
ARM: OMAP2+: Add missing put_device() call in omapdss_init_of()
OMAP2: fixup doc comments in omap_device
ARM: OMAP1: drop duplicated dependency on ARCH_OMAP1
ARM: ASPEED: update default ARCH_NR_GPIO for ARCH_ASPEED
ARM: imx: use generic function to exit coherency
ARM: tegra: Use WFE for power-gating on Tegra30
ARM: tegra: Fix FLOW_CTLR_HALT register clobbering by tegra_resume()
ARM: exynos: Enable exynos-asv driver for ARCH_EXYNOS
ARM: s3c: Rename s5p_usb_phy functions
ARM: s3c: Rename s3c64xx_spi_setname() function
ARM: imx: Add serial number support for i.MX6/7 SoCs
ARM: imx: Drop imx_anatop_usb_chrg_detect_disable()
arm64: Introduce config for S32
ARM: hisi: drop useless depend on ARCH_MULTI_V7
arm64: realtek: Select reset controller
ARM: shmobile: rcar-gen2: Drop legacy DT clock support
ARM: OMAP2+: Remove duplicated include from pmic-cpcap.c
ARM: OMAP1: ams-delta FIQ: Fix a typo ("Initiaize")
MAINTAINERS: Add logicpd-som-lv and logicpd-torpedo to OMAP TREE
ARM: OMAP2+: pdata-quirks: drop TI_ST/KIM support
...
|
|
Commit 99e98d3fb100 ("cpuidle: Consolidate disabled state checks")
overlooked the fact that the imx6q and tegra20 cpuidle drivers use
the "disabled" field in struct cpuidle_state for quirks which trigger
after the initialization of cpuidle, so reading the initial value of
that field is not sufficient for those drivers.
In order to allow them to implement the quirks without using the
"disabled" field in struct cpuidle_state, introduce a new helper
function and modify them to use it.
Fixes: 99e98d3fb100 ("cpuidle: Consolidate disabled state checks")
Reported-by: Len Brown <lenb@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Turned out that WFI doesn't work reliably on Tegra30 as a trigger for
the power-gating, it causes CPU hang under some circumstances like having
memory controller running of PLLP. The TRM doc states that WFI should be
used for the Big-Little "Cluster Switch", while WFE for the power-gating.
Hence let's use the WFE for CPU0 power-gating, like it is done for the
power-gating of a secondary cores. This fixes CPU hang after entering LP2
with memory running off PLLP.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
There is an unfortunate typo in the code that results in writing to
FLOW_CTLR_HALT instead of FLOW_CTLR_CSR.
Cc: <stable@vger.kernel.org>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning:
arch/arm/mach-tegra/reset.c: In function 'tegra_cpu_reset_handler_enable':
arch/arm/mach-tegra/reset.c:72:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
tegra_cpu_reset_handler_set(reset_address);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/arm/mach-tegra/reset.c:74:2: note: here
case 0:
^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
|
|
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
51 franklin street fifth floor boston ma 02110 1301 usa
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option [no]_[pad]_[ctrl] any later version this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin street fifth floor boston ma
02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 176 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154040.652910950@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
Among the larger pieces:
- Power management improvements for TI am335x and am437x (RTC
suspend/wake)
- Misc new additions for Amlogic (socinfo updates)
- ZynqMP FPGA manager
- Nvidia improvements for reset/powergate handling
- PMIC wrapper for Mediatek MT8516
- Misc fixes/improvements for ARM SCMI, TEE, NXP i.MX SCU drivers"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (57 commits)
soc: aspeed: fix Kconfig
soc: add aspeed folder and misc drivers
spi: zynqmp: Fix build break
soc: imx: Add generic i.MX8 SoC driver
MAINTAINERS: Update email for Qualcomm SoC maintainer
memory: tegra: Fix a typos for "fdcdwr2" mc client
Revert "ARM: tegra: Restore memory arbitration on resume from LP1 on Tegra30+"
memory: tegra: Replace readl-writel with mc_readl-mc_writel
memory: tegra: Fix integer overflow on tick value calculation
memory: tegra: Fix missed registers values latching
ARM: tegra: cpuidle: Handle tick broadcasting within cpuidle core on Tegra20/30
optee: allow to work without static shared memory
soc/tegra: pmc: Move powergate initialisation to probe
soc/tegra: pmc: Remove reset sysfs entries on error
soc/tegra: pmc: Fix reset sources and levels
soc: amlogic: meson-gx-pwrc-vpu: Add support for G12A
soc: amlogic: meson-gx-pwrc-vpu: Fix power on/off register bitmask
fpga manager: Adding FPGA Manager support for Xilinx zynqmp
dt-bindings: fpga: Add bindings for ZynqMP fpga driver
firmware: xilinx: Add fpga API's
...
|
|
Pull ARM SoC platform updates from Olof Johansson:
"SoC updates, mostly refactorings and cleanups of old legacy platforms.
Major themes this release:
- Conversion of ixp4xx to a modern platform (drivers, DT, bindings)
- Moving some of the ep93xx headers around to get it closer to
multiplatform enabled.
- Cleanups of Davinci
This also contains a few patches that were queued up as fixes before
5.1 but I didn't get sent in before release"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
ARM: debug-ll: add default address for digicolor
ARM: u300: regulator: add MODULE_LICENSE()
ARM: ep93xx: move private headers out of mach/*
ARM: ep93xx: move pinctrl interfaces into include/linux/soc
ARM: ep93xx: keypad: stop using mach/platform.h
ARM: ep93xx: move network platform data to separate header
ARM: stm32: add AMBA support for stm32 family
MAINTAINERS: update arch/arm/mach-davinci
ARM: rockchip: add missing of_node_put in rockchip_smp_prepare_pmu
ARM: dts: Add queue manager and NPE to the IXP4xx DTSI
soc: ixp4xx: qmgr: Add DT probe code
soc: ixp4xx: qmgr: Add DT bindings for IXP4xx qmgr
soc: ixp4xx: npe: Add DT probe code
soc: ixp4xx: Add DT bindings for IXP4xx NPE
soc: ixp4xx: qmgr: Pass resources
soc: ixp4xx: Remove unused functions
soc: ixp4xx: Uninline several functions
soc: ixp4xx: npe: Pass addresses as resources
ARM: ixp4xx: Turn the QMGR into a platform device
ARM: ixp4xx: Turn the NPE into a platform device
...
|
|
Since commit dccd2304cc90 ("ARM: 7430/1: sizes.h: move from asm-generic
to <linux/sizes.h>"), <asm/sizes.h> and <asm-generic/sizes.h> are just
wrappers of <linux/sizes.h>.
This commit replaces all <asm/sizes.h> and <asm-generic/sizes.h> to
prepare for the removal.
Link: http://lkml.kernel.org/r/1553267665-27228-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/drivers
ARM: tegra: Core changes for v5.2-rc1
One of these patches enables PM by default on 32-bit ARM, following the
same default that we already have on 64-bit ARM. The other patch fixes a
cosmetic issue in the cpuidle driver for Tegra20 and Tegra30.
* tag 'tegra-for-5.2-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: cpuidle: Handle tick broadcasting within cpuidle core on Tegra20/30
ARM: tegra: enforce PM requirement
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Turned out that the actual bug was in the Memory Controller driver
that programmed shadowed registers without latching the new values
and then there was a bug on EMEM arbitration configuration calculation
that results in a wrong value being latched on resume from suspend.
The Memory Controller has been fixed properly now, hence the workaround
patch could be reverted safely.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Tegra20/30 drivers do not handle the tick_broadcast_enter() error which
potentially could happen when CPU timer isn't permitted to be stopped.
Let's just move out the broadcasting to the CPUIDLE core by setting the
respective flag in the Tegra20/30 drivers. This patch doesn't fix any
problem because currently tick_broadcast_enter() could fail only on
ARM64, so consider this change as a minor cleanup.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Move the Trusted Foundations support out of arch/arm/firmware and into
drivers/firmware where most other firmware support implementations are
located.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The list of dependencies has become unsorted, which makes it difficult
to find the right place to insert new dependencies. Restore alphabetical
order to make future additions easier.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
In order to suspend-resume CPU with Trusted Foundations firmware being
present on Tegra30, the LP1/LP2 boot vectors and CPU caches need to be
set up using the firmware calls and then suspend code shall avoid
re-disabling parts that were disabled by the firmware.
Tested-by: Robert Yang <decatf@gmail.com>
Tested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
CPU always jumps into reset handler in ARM-mode from the Trusted
Foundations firmware, hence let's make CPU to always jump into kernel
in ARM-mode regardless of the firmware presence. This is required to
make Thumb-2 kernel working with the Trusted Foundations firmware on
Tegra30.
Tested-by: Robert Yang <decatf@gmail.com>
Tested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
CPU isn't allowed to touch secure registers while running under secure
monitor. Hence skip applying of CPU erratas in the reset handler if
Trusted Foundations firmware presents.
Partially based on work done by Michał Mirosław [1].
[1] https://www.spinics.net/lists/arm-kernel/msg594768.html
Tested-by: Robert Yang <decatf@gmail.com>
Tested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
On Tegra30 L2 cache should be initialized using firmware call if CPU
is running in insecure mode. Set up the required outer-cache write_sec()
callback early during boot using the firmware API, it is always a NO-OP
on T114+ and is NO-OP on T20/30 if Trusted Foundations firmware node
isn't present in device-tree.
Tested-by: Robert Yang <decatf@gmail.com>
Tested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Trusted Foundations firmware call varies depending on the required
suspend-mode. Make the firmware API to take the mode argument in order
to expose all of the modes to firmware user.
Tested-by: Robert Yang <decatf@gmail.com>
Tested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Currently runtime PM is enabled for Tegra HDA driver. One of the concern
raised was about handling !PM case in HDA driver. In this case, there is
a need to manage clocks and power explicitly in the driver and reviewers
were not really convinced about this. The consensus at the end was to
enforce PM requirement to keep things simple, rather driver mentioning a
dependency on PM. This is how it is done for ARM 64-bit Tegra platforms
and the same can be done for 32-bit Tegra platforms too.
Finally the objective is to remove dependency on PM availability for all
Tegra drivers. The detailed discussion can be found in following patch,
https://patchwork.ozlabs.org/patch/1031007/
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Jonathan Hunter <jonathanh@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Pull ARM updates from Russell King:
- An improvement from Ard Biesheuvel, who noted that the identity map
setup was taking a long time due to flush_cache_louis().
- Update a comment about dma_ops from Wolfram Sang.
- Remove use of "-p" with ld, where this flag has been a no-op since
2004.
- Remove the printing of the virtual memory layout, which is no longer
useful since we hide pointers.
- Correct SCU help text.
- Remove legacy TWD registration method.
- Add pgprot_device() implementation for mapping PCI sysfs resource
files.
- Initialise PFN limits earlier for kmemleak.
- Fix argument count to match macro definition (affects clang builds)
- Use unified assembler language almost everywhere for clang, and other
clang improvements (from Stefan Agner, Nathan Chancellor).
- Support security extension for noMMU and other noMMU cleanups (from
Vladimir Murzin).
- Remove unnecessary SMP bringup code (which was incorrectly copy'n'
pasted from the ARM platform implementations) and remove it from the
arch code to discourge further copys of it appearing.
- Add Cortex A9 erratum preventing kexec working on some SoCs.
- AMBA bus identification updates from Mike Leach.
- More use of raw spinlocks to avoid -RT kernel issues (from Yang Shi
and Sebastian Andrzej Siewior).
- MCPM hyp/svc mode mismatch fixes from Marek Szyprowski.
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (32 commits)
ARM: 8849/1: NOMMU: Fix encodings for PMSAv8's PRBAR4/PRLAR4
ARM: 8848/1: virt: Align GIC version check with arm64 counterpart
ARM: 8847/1: pm: fix HYP/SVC mode mismatch when MCPM is used
ARM: 8845/1: use unified assembler in c files
ARM: 8844/1: use unified assembler in assembly files
ARM: 8843/1: use unified assembler in headers
ARM: 8841/1: use unified assembler in macros
ARM: 8840/1: use a raw_spinlock_t in unwind
ARM: 8839/1: kprobe: make patch_lock a raw_spinlock_t
ARM: 8837/1: coresight: etmv4: Update ID register table to add UCI support
ARM: 8836/1: drivers: amba: Update component matching to use the CoreSight UCI values.
ARM: 8838/1: drivers: amba: Updates to component identification for driver matching.
ARM: 8833/1: Ensure that NEON code always compiles with Clang
ARM: avoid Cortex-A9 livelock on tight dmb loops
ARM: smp: remove arch-provided "pen_release"
ARM: actions: remove boot_lock and pen_release
ARM: oxnas: remove CPU hotplug implementation
ARM: qcom: remove unnecessary boot_lock
ARM: 8832/1: NOMMU: Limit visibility for CONFIG_FLASH_{MEM_BASE,SIZE}
ARM: 8831/1: NOMMU: pmsa-v8: remove unneeded semicolon
...
|
|
Use unified assembler syntax (UAL) in assembly files. Divided
syntax is considered deprecated. This will also allow to build
the kernel using LLVM's integrated assembler.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The external memory arbitration configuration is getting reset after
memory entering into self-refresh mode, it shall be restored on the
exit. Note that MC_EMEM_ARB_CFG register is shadowed and latching
happens on the EMC timing update. This fixes 2x GPU performance
degradation after resuming from LP1 on Tegra30.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The DRAM refresh-interval is getting erroneously set to "1" on exiting
from memory self-refreshing mode. The clobbered interval causes the
"refresh request overflow timeout" error raised by the External Memory
Controller on exiting from LP1 on Tegra30. The same may happen on Tegra20,
but EMC registers are not latched after exiting from self-refreshing mode
on Tegra20 and hence refresh-interval is not altered until an event that
causes registers latching happens.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The memory interface configuration and re-calibration interval are left
unassigned on resume from LP1 because these registers are shadowed and
require latching after being adjusted.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
WARNING: vmlinux.o(.text+0x39ecc): Section mismatch in reference from the function tegra114_gic_cpu_pm_registration() to the (unknown reference) .init.rodata:(unknown)
The function tegra114_gic_cpu_pm_registration() references
the (unknown reference) __initconst (unknown).
This is often because tegra114_gic_cpu_pm_registration lacks a __initconst
annotation or the annotation of (unknown) is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"Here are the main updates for SoC support (besides DT additions) for
ARM 32- and 64-bit platforms. The branch also contains defconfig
updates to turn on drivers and options as needed on the various
platforms.
The largest parts of the delta are from cleanups moving platform data
and board file setup of TI platforms to ti-sysc bus drivers. There are
also some sweeping changes of eeprom and nand setup on Davinci, i.MX
and other platforms.
Samsung is removing support for Exynos5440, which was an oddball SoC
that hasn't been seen much use in designs.
Renesas is adding support for new SoCs (R-Car E3, RZ/G1C and RZ/N1D).
Linus Walleij is also removing support for ux500 (Sony Ericsson)
U8540/9540 SoCs that never made it to significant mass production and
products"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (133 commits)
MAINTAINERS: add NXP linux team maillist as i.MX reviewer
ARM: stm32: Don't select DMA unconditionally on STM32MP157C
arm64: defconfig: Enable PCIe on msm8996 and db820c
ARM: pxa3xx: enable external wakeup pins
ARM: pxa: stargate2: use device properties for at24 eeprom
arm64: defconfig: Enable HISILICON_LPC
arm64: defconfig: enable drivers for Poplar support
arm64: defconfig: Enable UFS on msm8996
ARM: berlin: switch to SPDX license identifier
arm: berlin: remove non-necessary flush_cache_all()
ARM: berlin: extend BG2CD Kconfig entry
OMAP: CLK: CLKSRC: Add suspend resume hooks
ARM: AM43XX: Add functions to save/restore am43xx control registers
ASoC: ams_delta: use GPIO lookup table
ARM: OMAP1: ams-delta: add GPIO lookup tables
bus: ti-sysc: Fix optional clocks array access
ARM: OMAP2+: Make sure LOGICRETSTATE bits are not cleared
ARM: OMAP2+: prm44xx: Inroduce cpu_pm notifiers for context save/restore
ARM: OMAP2+: prm44xx: Introduce context save/restore for am43 PRCM IO
ARM: OMAP2+: powerdomain: Introduce cpu_pm notifiers for context save/restore
...
|
|
Tegra20-cpufreq driver require a platform device in order to be loaded,
instantiate a simple platform device for the driver during of the machines
late initialization.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Define this symbol if the architecture either uses 64-bit pointers or the
PHYS_ADDR_T_64BIT is set. This covers 95% of the old arch magic. We only
need an additional select for Xen on ARM (why anyway?), and we now always
set ARCH_DMA_ADDR_T_64BIT on mips boards with 64-bit physical addressing
instead of only doing it when highmem is set.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: James Hogan <jhogan@kernel.org>
|
|
Conflicts:
include/linux/compiler-clang.h
include/linux/compiler-gcc.h
include/linux/compiler-intel.h
include/uapi/linux/stddef.h
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
to READ_ONCE()/WRITE_ONCE()
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"This branch contains platform-related driver updates for ARM and ARM64.
Among them:
- Reset driver updates:
+ New API for dealing with arrays of resets
+ Make unimplemented {de,}assert return success on shared resets
+ MSDKv1 driver
+ Removal of obsolete Gemini reset driver
+ Misc updates for sunxi and Uniphier
- SoC drivers:
+ Platform SoC driver registration on Tegra
+ Shuffle of Qualcomm drivers into a submenu
+ Allwinner A64 support for SRAM
+ Renesas R-Car R3 support
+ Power domains for Rockchip RK3366
- Misc updates and smaller fixes for TEE and memory driver
subsystems"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
firmware: arm_scpi: fix endianness of dev_id in struct dev_pstate_set
soc/tegra: fuse: Add missing semi-colon
soc/tegra: Restrict SoC device registration to Tegra
drivers: soc: sunxi: add support for A64 and its SRAM C
drivers: soc: sunxi: add support for remapping func value to reg value
drivers: soc: sunxi: fix error processing on base address when claiming
dt-bindings: add binding for Allwinner A64 SRAM controller and SRAM C
bus: sunxi-rsb: Enable by default for ARM64
soc/tegra: Register SoC device
firmware: tegra: set drvdata earlier
memory: Convert to using %pOF instead of full_name
soc: Convert to using %pOF instead of full_name
bus: Convert to using %pOF instead of full_name
firmware: Convert to using %pOF instead of full_name
soc: mediatek: add SCPSYS power domain driver for MediaTek MT7622 SoC
soc: mediatek: add header files required for MT7622 SCPSYS dt-binding
soc: mediatek: reduce code duplication of scpsys_probe across all SoCs
dt-bindings: soc: update the binding document for SCPSYS on MediaTek MT7622 SoC
reset: uniphier: add analog amplifiers reset control
reset: uniphier: add video input subsystem reset control
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM/arm64 SoC platform updates from Olof Johansson: "This branch
contains platform updates for 32- and 64-bit ARM, including defconfig
updates to enable new options, drivers and platforms. There are also a
few fixes and cleanups for some existing vendors.
Some of the things worth highlighting here are:
- Enabling new crypt drivers on arm64 defconfig
- QCOM IPQ8074 clocks and pinctrl drivers on arm64 defconfig
- Debug support enabled for Renesas r8a7743
- Various config updates for Renesas platforms (sound, USB, other
drivers)
- Platform support (including SMP) for TI dra762
- OMAP cleanups: Move to use generic 8250 debug_ll, removal of stale
DMA code"
* tag 'armsoc-platforms' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (109 commits)
ARM: multi_v7_defconfig: make eSDHC driver built-in
arm64: defconfig: enable rockchip graphics
MAINTAINERS: Update Cavium ThunderX2 entry
ARM: config: aspeed: Add I2C, VUART, LPC Snoop
ARM: configs: aspeed: Update Aspeed G4 with VMSPLIT_2G
ARM: s3c24xx: Fix NAND ECC mode for mini2440 board
ARM: davinci_all_defconfig: enable tinydrm and ST7586
arm64: defconfig: Enable QCOM IPQ8074 clock and pinctrl
ARM: defconfig: tegra: Enable ChipIdea UDC driver
ARM: configs: Add Tegra I2S interfaces to multi_v7_defconfig
ARM: tegra: Add Tegra I2S interfaces to defconfig
ARM: tegra: Update default configuration for v4.13-rc1
MAINTAINERS: update ARM/ZTE entry
soc: versatile: remove unnecessary static in realview_soc_probe()
ARM: Convert to using %pOF instead of full_name
ARM: hisi: Fix typo in comment
ARM: multi_v7_defconfig: add CONFIG_BRCMSTB_THERMAL
arm64: defconfig: add CONFIG_BRCMSTB_THERMAL
arm64: defconfig: add recently added crypto drivers as modules
arm64: defconfig: enable CONFIG_UNIPHIER_WATCHDOG
...
|
|
Move this code from arch/arm/mach-tegra and make it common among 32-bit
and 64-bit Tegra SoCs. This is slightly complicated by the fact that on
32-bit Tegra, the SoC device is used as the parent for all devices that
are instantiated from device tree.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Rename the ->enter_freeze cpuidle driver callback to ->enter_s2idle
to make it clear that it is used for entering suspend-to-idle and
rename the related functions, variables and so on accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This automatically selects options for zone DMA and 64 bit DMA addresses
when LPAE is enabled on ARM Tegra platforms. These options are required
for proper operation with LPAE enabled.
The ZONE_DMA option is required to ensure that drivers that allocate DMA
memory get buffers from the first 4 GiB. This is necessary because a lot
of the controllers only support addressing 32 bits.
As for ARCH_DMA_ADDR_T_64BIT, there are situations where devices that do
support addresses of more than 32 bits (such as the display controller
or the GPU) can run without translating addresses through an IOMMU on a
device with more than 4 GiB of system memory.
Note that both of these options are stop-gap solutions required only
until the IOMMU can be properly integrated with the DMA mapping API and
drivers use that properly and consistently.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
[treding@nvidia.com: specify rationale for options]
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The flowctrl driver is required for both ARM and ARM64 Tegra devices
and in order to enable support for it for ARM64, move the Tegra flowctrl
driver into drivers/soc/tegra.
By moving the flowctrl driver, tegra_flowctrl_init() is now called by
via an early initcall and to prevent this function from attempting to
mapping IO space for a non-Tegra device, a test for 'soc_is_tegra()'
is also added.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Tegra flowctrl.h header is included unnecessarily by the Tegra
sleep.S source file. Remove this unnecessary inclusion.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Pull ARM updates from Russell King:
- nommu updates from Afzal Mohammed cleaning up the vectors support
- allow DMA memory "mapping" for nommu Benjamin Gaignard
- fixing a correctness issue with R_ARM_PREL31 relocations in the
module linker
- add strlen() prototype for the decompressor
- support for DEBUG_VIRTUAL from Florian Fainelli
- adjusting memory bounds after memory reservations have been
registered
- unipher cache handling updates from Masahiro Yamada
- initrd and Thumb Kconfig cleanups
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (23 commits)
ARM: mm: round the initrd reservation to page boundaries
ARM: mm: clean up initrd initialisation
ARM: mm: move initrd init code out of arm_memblock_init()
ARM: 8655/1: improve NOMMU definition of pgprot_*()
ARM: 8654/1: decompressor: add strlen prototype
ARM: 8652/1: cache-uniphier: clean up active way setup code
ARM: 8651/1: cache-uniphier: include <linux/errno.h> instead of <linux/types.h>
ARM: 8650/1: module: handle negative R_ARM_PREL31 addends correctly
ARM: 8649/2: nommu: remove Hivecs configuration is asm
ARM: 8648/2: nommu: display vectors base
ARM: 8647/2: nommu: dynamic exception base address setting
ARM: 8646/1: mmu: decouple VECTORS_BASE from Kconfig
ARM: 8644/1: Reduce "CPU: shutdown" message to debug level
ARM: 8641/1: treewide: Replace uses of virt_to_phys with __pa_symbol
ARM: 8640/1: Add support for CONFIG_DEBUG_VIRTUAL
ARM: 8639/1: Define KERNEL_START and KERNEL_END
ARM: 8638/1: mtd: lart: Rename partition defines to be prefixed with PART_
ARM: 8637/1: Adjust memory boundaries after reservations
ARM: 8636/1: Cleanup sanity_check_meminfo
ARM: add CPU_THUMB_CAPABLE to indicate possible Thumb support
...
|
|
All low-level PM/SMP code using virt_to_phys() should actually use
__pa_symbol() against kernel symbols. Update code where relevant to move
away from virt_to_phys().
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Placement of attributes, such as __initdata, is standardized through the
checkpatch script. Fix up this instance to make checkpatch happy.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"The cleanup branch keeps going down in size as we've completed a lot
of the major legacy platform removals and conversions.
A handful of changes this time around, some of the themes or larger
sets are:
- A bunch of i.MX cleanups around platform detection, init call cleanups
- Misc fixes of missing/implicit includes
- Removal of ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (40 commits)
ARM: mps2: fix typo
ARM: s3c64xx: avoid warning about 'struct device_node'
bus: mvebu-mbus: make mvebu_mbus_syscore_ops static
bus: mvebu-mbus: fix __iomem on register pointers
ARM: tegra: Remove board_init_funcs array
ARM: iop: Fix indentation
ARM: imx: remove cpu_is_mx*()
ARM: imx: remove last call to cpu_is_mx5*
ARM: imx: rework mx27_pm_init() call
ARM: imx: deconstruct mx3_idle
ARM: imx: deconstruct mxc_rnga initialization
ARM: imx: remove cpu_is_mx1 check
ARM: i.MX: Do not explicitly call l2x0_of_init()
ARM: i.MX: system.c: Tweak prefetch settings for performance
ARM: i.MX: system.c: Replace magic numbers
ARM: i.MX: system.c: Remove redundant errata 752271 code
ARM: i.MX: system.c: Convert goto to if statement
ARM: Kirkwood: fix kirkwood_pm_init() declaration/type
ARM: Kirkwood: make kirkwood_disable_mbus_error_propagation() static
ARM: orion5x: make orion5x_legacy_handle_irq static
...
|
