summaryrefslogtreecommitdiff
path: root/arch/arm64/boot/dts/allwinner
AgeCommit message (Collapse)Author
2019-10-25Merge tag 'armsoc-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC fixes from Olof Johansson: "A slightly larger set of fixes have accrued in the last two weeks. Mostly a collection of the usual smaller fixes: - Marvell Armada: USB phy setup issues on Turris Mox - Broadcom: GPIO/pinmux DT mapping corrections for Stingray, MMC bus width fix for RPi Zero W, GPIO LED removal for RPI CM3. Also some maintainer updates. - OMAP: Fixlets for display config, interrupt settings for wifi, some clock/PM pieces. Also IOMMU regression fix and a ti-sysc no-watchdog regression fix. - i.MX: A few fixes around PM/settings, some devicetree fixlets and catching up with config option changes in DRM - Rockchip: RockRro64 misc DT fixups, Hugsun X99 USB-C, Kevin display panel settings ... and some smaller fixes for Davinci (backlight, McBSP DMA), Allwinner (phy regulators, PMU removal on A64, etc)" * tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (42 commits) ARM: dts: stm32: relax qspi pins slew-rate for stm32mp157 MAINTAINERS: Update the Spreadtrum SoC maintainer MAINTAINERS: Remove Gregory and Brian for ARCH_BRCMSTB ARM: dts: bcm2837-rpi-cm3: Avoid leds-gpio probing issue bus: ti-sysc: Fix watchdog quirk handling ARM: OMAP2+: Add pdata for OMAP3 ISP IOMMU ARM: OMAP2+: Plug in device_enable/idle ops for IOMMUs ARM: davinci_all_defconfig: enable GPIO backlight ARM: davinci: dm365: Fix McBSP dma_slave_map entry ARM: dts: bcm2835-rpi-zero-w: Fix bus-width of sdhci ARM: imx_v6_v7_defconfig: Enable CONFIG_DRM_MSM arm64: dts: imx8mn: Use correct clock for usdhc's ipg clk arm64: dts: imx8mm: Use correct clock for usdhc's ipg clk arm64: dts: imx8mq: Use correct clock for usdhc's ipg clk ARM: dts: imx7s: Correct GPT's ipg clock source ARM: dts: vf610-zii-scu4-aib: Specify 'i2c-mux-idle-disconnect' ARM: dts: imx6q-logicpd: Re-Enable SNVS power key arm64: dts: lx2160a: Correct CPU core idle state name mailmap: Add Simon Arlott (replacement for expired email address) arm64: dts: rockchip: Fix override mode for rk3399-kevin panel ...
2019-10-04ARM: dts: sunxi: Revert phy-names removal for ECHI and OHCIMaxime Ripard
This reverts commits 3d109bdca981 ("ARM: dts: sunxi: Remove useless phy-names from EHCI and OHCI"), 0a3df8bb6dad ("ARM: dts: sunxi: h3/h5: Remove useless phy-names from EHCI and OHCI") and 3c7ab90aaa28 ("arm64: dts: allwinner: Remove useless phy-names from EHCI and OHCI"). It turns out that while the USB bindings were not mentionning it, the PHY client bindings were mandating that phy-names is set when phys is. Let's add it back. Fixes: 3d109bdca981 ("ARM: dts: sunxi: Remove useless phy-names from EHCI and OHCI") Fixes: 0a3df8bb6dad ("ARM: dts: sunxi: h3/h5: Remove useless phy-names from EHCI and OHCI") Fixes: 3c7ab90aaa28 ("arm64: dts: allwinner: Remove useless phy-names from EHCI and OHCI") Reported-by: Emmanuel Vadot <manu@bidouilliste.com> Signed-off-by: Maxime Ripard <mripard@kernel.org> Link: https://lore.kernel.org/r/20191002112651.100504-1-mripard@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-30arm64: dts: allwinner: a64: sopine-baseboard: Add PHY regulator delayJernej Skrabec
It turns out that sopine-baseboard needs same fix as pine64-plus for ethernet PHY. Here too Realtek ethernet PHY chip needs additional power on delay to properly initialize. Datasheet mentions that chip needs 30 ms to be properly powered on and that it needs some more time to be initialized. Fix that by adding 100ms ramp delay to regulator responsible for powering PHY. Note that issue was found out and fix tested on pine64-lts, but it's basically the same as sopine-baseboard, only layout and connectors differ. Fixes: bdfe4cebea11 ("arm64: allwinner: a64: add Ethernet PHY regulator for several boards") Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by: Maxime Ripard <mripard@kernel.org>
2019-09-30arm64: dts: allwinner: a64: Drop PMU nodeVasily Khoruzhick
Looks like PMU in A64 is broken, it generates no interrupts at all and as result 'perf top' shows no events. Tested on Pine64-LTS. Fixes: 34a97fcc71c2 ("arm64: dts: allwinner: a64: Add PMU node") Cc: Harald Geyer <harald@ccbib.org> Cc: Jared D. McNeill <jmcneill@NetBSD.org> Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> Reviewed-by: Emmanuel Vadot <manu@FreeBSD.org> Signed-off-by: Maxime Ripard <mripard@kernel.org>
2019-09-30arm64: dts: allwinner: a64: pine64-plus: Add PHY regulator delayJernej Skrabec
Depending on kernel and bootloader configuration, it's possible that Realtek ethernet PHY isn't powered on properly. According to the datasheet, it needs 30ms to power up and then some more time before it can be used. Fix that by adding 100ms ramp delay to regulator responsible for powering PHY. Fixes: 94dcfdc77fc5 ("arm64: allwinner: pine64-plus: Enable dwmac-sun8i") Suggested-by: Ondrej Jirman <megous@megous.com> Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by: Maxime Ripard <mripard@kernel.org>
2019-08-23arm64: dts: allwinner: orange-pi-3: Enable WiFiOndrej Jirman
Orange Pi 3 has AP6256 WiFi/BT module. WiFi part of the module is called bcm43356 and can be used with the brcmfmac driver. The module is powered by the two always on regulators (not AXP805). WiFi uses a PG port with 1.8V voltage level signals. SoC needs to be configured so that it sets up an 1.8V input bias on this port. This is done by the pio driver by reading the vcc-pg-supply voltage. You'll need a fw_bcm43456c5_ag.bin firmware file and nvram.txt configuration that can be found in the Xulongs's repository for H6: https://github.com/orangepi-xunlong/OrangePiH6_external/tree/master/ap6256 Mainline brcmfmac driver expects the firmware and nvram at the following paths relative to the firmware directory: brcm/brcmfmac43456-sdio.bin brcm/brcmfmac43456-sdio.txt Signed-off-by: Ondrej Jirman <megous@megous.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-08-23ARM: dts: sunxi: Add missing watchdog clocksMaxime Ripard
The watchdog has a clock on all our SoCs, but it wasn't always listed. Add it to the devicetree where it's missing. Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-08-23arm64: dts: allwinner: h6: Add support for RTC and fix the clock treeOndrej Jirman
This patch adds RTC node and fixes the clock properties and nodes to reflect the real clock tree. The device nodes for the internal oscillator and osc32k are removed, as these clocks are now provided by the RTC device. Clock references are fixed accordingly, too. Signed-off-by: Ondrej Jirman <megous@megous.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-08-23arm64: dts: allwinner: a64: Add A64 OlinuXino board (with eMMC)Sunil Mohan Adapa
A64 OLinuXino board from Olimex has three variants with onboard eMMC: A64-OLinuXino-1Ge16GW, A64-OLinuXino-1Ge4GW and A64-OLinuXino-2Ge8G-IND. In addition, there are two variants without eMMC. One without eMMC and one with SPI flash. This suggests the need for separate device tree for the three eMMC variants. This patch has been tested on A64-OLinuXino-1Ge16GW with Linux 5.0 from Debain. Basic benchmarks using Flexible IO Tester show reasonable performance from the eMMC. eMMC - Random Write: 21.3MiB/s eMMC - Sequential Write: 68.2MiB/s SD Card - Random Write: 1690KiB/s SD Card - Sequential Write: 11.0MiB/s Changes: v3: Separate dts for eMMC variants v2: Fix descriptions for VCC and VCCQ Link: https://github.com/armbian/build/commit/174953de1eb09e6aa1ef7075066b573dba625398 Signed-off-by: Martin Ayotte <martinayotte@gmail.com> [sunil@medhas.org Fix descriptions for VCC and VCCQ, separate dts for eMMC] Signed-off-by: Sunil Mohan Adapa <sunil@medhas.org> Tested-by: Sunil Mohan Adapa <sunil@medhas.org> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-08-23arm64: dts: allwinner: h6: Introduce Tanix TX6 boardJernej Skrabec
Tanix TX6 is an Allwinner H6 based TV box, which supports: - Allwinner H6 Quad-core 64-bit ARM Cortex-A53 - GPU Mali-T720 - 4GiB DDR3 RAM (3GiB useable) - 100Mbps EMAC via AC200 EPHY - Cdtech 47822BS Wifi/BT - 2x USB 2.0 Host and 1x USB 3.0 Host - HDMI port - IR receiver - 64GiB eMMC - 5V/2A DC power supply Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-08-23arm64: allwinner: h6: add I2C nodesBhushan Shah
Add device-tree nodes for i2c0 to i2c2, and also add relevant pinctrl nodes. Suggested-by: Icenowy Zheng <icenowy@aosc.io> Signed-off-by: Bhushan Shah <bshah@kde.org> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-08-23arm64: dts: allwinner: Enable DDC regulator for Beelink GS1Clément Péron
Beelink GS1 has a DDC I2C bus voltage shifter. This is actually missing and video is limited to 1024x768 due to missing EDID information. Add the DDC regulator in the device-tree. Signed-off-by: Clément Péron <peron.clem@gmail.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-08-23arm64: dts: allwinner: h6: Enable SPDIF for Beelink GS1Clément Péron
Beelink GS1 board has a SPDIF out connector, so enable it in the device-tree and add a simple SPDIF soundcard. Signed-off-by: Clément Péron <peron.clem@gmail.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-08-23arm64: dts: allwinner: Add SPDIF node for Allwinner H6Clément Péron
The Allwinner H6 has a SPDIF controller called OWA (One Wire Audio). Only one pinmuxing is available so set it as default. Signed-off-by: Clément Péron <peron.clem@gmail.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-08-23arm64: dts: allwinner: orange-pi-3: Enable HDMI outputOndrej Jirman
Orange Pi 3 has a DDC_CEC_EN signal connected to PH2, that enables the DDC I2C bus voltage shifter. Before EDID can be read, we need to pull PH2 high. This is realized by the ddc-en-gpios property. Signed-off-by: Ondrej Jirman <megous@megous.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-07-24arm64: dts: allwinner: h6: Enable IR on H6 boardsClément Péron
Beelink GS1, OrangePi H6 boards and Pine H64 have an IR receiver. Enable it in their device-tree. Signed-off-by: Clément Péron <peron.clem@gmail.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-07-24arm64: dts: allwinner: h6: Add IR receiver nodeClément Péron
Allwinner H6 IR is similar to A31 and can use same driver. Add support for it. Signed-off-by: Clément Péron <peron.clem@gmail.com> Acked-by: Sean Young <sean@mess.org> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-07-24arm64: dts: allwinner: a64: Enable IR on Orange Pi WinJernej Skrabec
OrangePi Win board contains IR receiver. Enable it. Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by: Clément Péron <peron.clem@gmail.com> Acked-by: Sean Young <sean@mess.org> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-07-24arm64: dts: allwinner: a64: Add IR nodeIgors Makejevs
IR peripheral is completely compatible with A31 one. Signed-off-by: Igors Makejevs <git_bb@bwzone.com> Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by: Clément Péron <peron.clem@gmail.com> Acked-by: Sean Young <sean@mess.org> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-07-23ARM: dts: sunxi: Fix the HDMI PHY nameMaxime Ripard
Even though the binding mentions that the PHY name must be "phy", it turns out that all our DTs had "hdmi-phy" instead. The code doesn't care about the phy-names property, so we can just change our DTs to match the binding, without any side effect. Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-07-22arm64: dts: allwinner: h6: Fix SID node nameMaxime Ripard
The SID node one the H6 doesn't have a standard node name. Switch to the one we use for the other SoCs. Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-07-22ARM: dts: sunxi: Unify the DE2 bus clocks orderMaxime Ripard
The DE2 bus takes two clocks, named bus and mod according to the binding. However, the order of these clocks change from one SoC to another. Even though it might not be an issue in most cases, having consistency will help if we ever need to have some code to deal with deprecated bindings, and in general it's just better. Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-07-04Merge tag 'sunxi-dt64-for-5.3-round-2' of ↵Olof Johansson
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt Allwinner DT64 Changes for 5.3 - Round 2 One extra change wiring up the interrupt line for the external RTC chip on the Pine H64. * tag 'sunxi-dt64-for-5.3-round-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: arm64: dts: allwinner: h6: Pine H64: Add interrupt line for RTC Link: https://lore.kernel.org/r/20190704065326.GA19010@wens.csie.org Signed-off-by: Olof Johansson <olof@lixom.net>
2019-06-25Merge tag 'sunxi-h3-h5-for-5.3-201906210812' of ↵Olof Johansson
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt This time we only have a single patch for our command branch between arm and arm64, a fix for the array syntax raised by our DT schemas. * tag 'sunxi-h3-h5-for-5.3-201906210812' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: ARM: dts: sunxi: h3/h5: Fix GPIO regulator state array Signed-off-by: Olof Johansson <olof@lixom.net>
2019-06-24arm64: dts: allwinner: h6: Pine H64: Add interrupt line for RTCChen-Yu Tsai
The external PCF8563 RTC chip's interrupt line is connected to the NMI line on the SoC. Add the interrupt line to the device tree. Fixes: 17ebc33afc35 ("arm64: allwinner: h6: add PCF8563 RTC on Pine H64 board") Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Chen-Yu Tsai <wens@csie.org>
2019-06-12arm64: dts: allwinner: h6: Add DMA nodeJernej Skrabec
H6 has DMA controller which supports 16 channels. Add a node for it. Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by: Clément Péron <peron.clem@gmail.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-06-05arm64: dts: allwinner: a64: Add lradc nodeLuca Weiss
Add a node describing the KEYADC on the A64. Signed-off-by: Luca Weiss <luca@z3ntu.xyz> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-05-29ARM: dts: sunxi: h3/h5: Fix GPIO regulator state arrayMaxime Ripard
Even though it translates to the same thing down to the binary level, we should have an array of 2 number cells to describe each voltage state, which in turns create a validation warning. Let's fix this. Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-05-24arm64: dts: allwinner: h6: add r_watchog nodeClément Péron
Allwinner H6 has a r_watchdog similar to A64. Declare it in the device-tree. Signed-off-by: Clément Péron <peron.clem@gmail.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-05-24arm64: dts: allwinner: h6: add watchdog nodeClément Péron
Allwinner H6 has a watchog node which seems broken on some boards. Test has been performed on several boards. Chen-Yu Tsai boards: Pine H64 - H6448BA 7782 => OK OrangePi Lite 2 - H8068BA 61C2 => KO Martin Ayotte boards: Pine H64 - H8069BA 6892 => OK OrangePi 3 - HA047BA 69W2 => KO OrangePi One Plus - H7310BA 6842 => KO OrangePi Lite2 - H6448BA 6662 => KO Clément Péron board: Beelink GS1 - H7309BA 6842 => KO As it seems not fixable for now, declare the node but leave it disable with a comment. Signed-off-by: Clément Péron <peron.clem@gmail.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-05-20arm64: dts: allwinner: a64: Enable audio on Teres-IHarald Geyer
The TERES-I has internal speakers (left, right), internal microphone and a headset combo jack (headphones + mic), "CTIA" (android) pinout. The headphone and mic detect lines of the A64 are connected properly, but AFAIK currently unsupported by the driver. Reviewed-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Harald Geyer <harald@ccbib.org> Signed-off-by: Torsten Duwe <duwe@suse.de> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-05-20arm64: dts: allwinner: a64: bananapi-m64: Enable PMIC USB power supplyChen-Yu Tsai
The Bananapi M64 has a micro-USB connector with USB OTG support (that is already enabled). VBUS from this connector is wired to the PMIC's VBUS input. Enable the PMIC's USB power supply on this board, and also hook it up to the USB PHY. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-05-20arm64: dts: allwinner: axp803: add USB power supply nodeChen-Yu Tsai
The AXP803 has a VBUS power input. Add a device node for it, now that we support it. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-05-20arm64: dts: allwinner: a64: Add pinmux for RGB666 LCDIcenowy Zheng
Allwinner A64's TCON0 can output RGB666 LCD signal. Add its pinmux. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Torsten Duwe <duwe@suse.de> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-05-20arm64: dts: allwinner: a64: orangepi-win: Add wifi and bluetooth nodesJernej Skrabec
The AP6212 is based on the Broadcom BCM43430 or BCM43438. The WiFi side identifies as BCM43430, while the Bluetooth side identifies as BCM43438. WiFi is connected to mmc1 and the Bluetooth side is connected to UART1 in a 4 wire configuration. Same as the WiFi side, due to being the same chip and package, DLDO2 provides overall power via VBAT, and DLDO4 provides I/O power via VDDIO. The RTC clock output provides the LPO low power clock at 32.768 kHz. This patch enables WiFi and Bluetooth on OrangePi Win boards and adds missing LPO clock on the WiFi side. PCM connection also exists for Bluetooth audio, but it's not used here. Bluetooth UART speed is set to 1.5 MBaud in order to be able transmit audio. While module supports even higher speeds, currently sunxi clock driver doesn't support higher speed. Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-05-20arm64: dts: allwinner: h6: add PIO VCC bank supplies for Pine H64Icenowy Zheng
The Allwinner H6 SoC features tweakable VCC for PC, PD, PG, PL and PM banks. This patch adds supplies for these banks except PL bank. PL bank is where PMIC is attached, and currently if a PMIC regulator is added for it a dependency loop will happen. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-05-20arm64: dts: allwinner: a64-oceanic-5205-5inmfd: Enable GT911 CTPJagan Teki
Goodix GT911 CTP is bound with Oceanic 5205 5inMFD board. The CTP connected to board with, - SDA, SCK from i2c0 - GPIO-LD0 as AVDD28 supply - PH4 gpio as interrupt pin - PH11 gpio as reset pin - X axis is inverted - Y axis is inverted Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-05-20arm64: dts: allwinner: a64-amarula-relic: Add GT5663 CTP nodeJagan Teki
Add Goodix GT5663 capacitive touch controller node on Amarula A64-Relic board. The CTP connected to board with, - SDA, SCK from i2c1 - GPIO-LD0 as AVDD28 supply - PH4 gpio as interrupt pin - PH8 gpio as reset pin - X axis is inverted - Y axis is inverted Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-05-20arm64: dts: allwinner: a64: move I2C pinctrl to dtsiJagan Teki
There is only one pinmuxing available for each I2C controller. So, move pinctrl for i2c0, i2c1 from board dts files into SoC dtsi. By moving these pinctrls the i2c1 node from Nanopi A64 just have a status, which is disabled already so remove the entire node from it. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-04-28Merge tag 'sunxi-h3-h5-for-5.2' of ↵Olof Johansson
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt Allwinner H3/H5 changes for 5.2 Our usual bunch of changes shared between arm and arm64, the most notable one being: - Fix of improper usage of DT bindings, thanks to the DT validation - Add the SID for the H3 and H5 - New board: RerVision H3-DVK * tag 'sunxi-h3-h5-for-5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: ARM: dts: sun8i: mapleboard: Remove cd-inverted ARM: dts: sunxi: h3/h5: Remove useless phy-names from EHCI and OHCI ARM: dts: sun8i: h3: bluetooth for Banana Pi M2 Zero board ARM: dts: sun8i: h3: Add default dr_mode ARM: dts: sun8i: h3: Refactor the pinctrl node names ARM: dts: sunxi: h3/h5: Remove stale pinctrl-names entry ARM: dts: sunxi: h3/h5: Add device node for SID ARM: dts: sun8i-h3: Add support for the RerVision H3-DVK board Signed-off-by: Olof Johansson <olof@lixom.net>
2019-04-28Merge tag 'sunxi-dt64-for-5.2' of ↵Olof Johansson
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt Allwinner arm64 DT changes for 5.2 Our usual bunch of patches, the most notable one being: - Fixing the DTC warnings - Fix DT bindings not being properly respected, thanks to the DT validation - New Board: Oceanic 5205, Beelink GS1, Orange Pi3 * tag 'sunxi-dt64-for-5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (22 commits) arm64: dts: allwinner: a64-amarula-relic: Add OV5640 camera node arm64: dts: allwinner: a64: Add pinmux setting for CSI MCLK on PE1 arm64: dts: allwinner: Fix DE2 bus node name arm64: dts: allwinner: Remove useless phy-names from EHCI and OHCI arm64: dts: allwinner: h6: Add MMC1 pins arm64: dts: allwinner: h6: Add Orange Pi 3 DTS arm64: dts: allwinner: h6: Introduce Beelink GS1 board dt-bindings: vendor-prefixes: add AZW arm64: dts: allwinner: h6: move MMC pinctrl to dtsi arm64: dts: allwinner: h6: Add device node for SID arm64: dts: allwinner: a64: Fix the Codec I2S binding arm64: dts: allwinner: a64: Add default dr_mode arm64: dts: allwinner: Fix pinctrl node names arm64: dts: allwinner: a64: Add missing PIO clocks arm64: dts: allwinner: a64: Fix display pipeline endpoints arm64: dts: allwinner: a64: Fix the TCON output clock arm64: dts: allwinner: h6: Add Video Engine node arm64: dts: allwinner: a64: Add cross links for the mixers arm64: allwinner: a64: Add Oceanic 5205 5inMFD initial support dt-bindings: Add vendor prefix for oceanic ... Signed-off-by: Olof Johansson <olof@lixom.net>
2019-04-18arm64: dts: allwinner: a64-amarula-relic: Add OV5640 camera nodeJagan Teki
Amarula A64-Relic board by default bound with OV5640 camera, so add support for it with below pin information. - PE13, PE12 via i2c-gpio bitbanging - CLK_CSI_MCLK as external clock - PE1 as external clock pin muxing - ALDO1 as AVDD supply - DLDO3 as DOVDD supply - ELDO3 as DVDD supply - PE14 gpio for reset pin - PE15 gpio for powerdown pin Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-04-18arm64: dts: allwinner: a64: Add pinmux setting for CSI MCLK on PE1Jagan Teki
Some camera modules have the SoC feeding a master clock to the sensor instead of having a standalone crystal. This clock signal is generated from the clock control unit and output from the CSI MCLK function of pin PE1. Add a pinmux setting for it for camera sensors to reference. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-04-17arm64: dts: allwinner: Fix DE2 bus node nameMaxime Ripard
According to the device tree specification, any bus should have a 'bus' node name. Since it isn't the case for us on the DE2 bus, fix that. Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-04-17arm64: dts: allwinner: Remove useless phy-names from EHCI and OHCIMaxime Ripard
Neither the OHCI or EHCI bindings are using the phy-names property, so we can just drop it. Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-04-15arm64: dts: allwinner: h6: Add MMC1 pinsOndrej Jirman
MMC1 is used on some H6 boards we want to support. Typical use is 4-bit SDIO interface with a WiFi chip. Add pin definitions for this use case. As this is the only possible configration for mmc1, make it the default one, too. Signed-off-by: Ondrej Jirman <megous@megous.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-04-09arm64: dts: allwinner: h6: Add Orange Pi 3 DTSOndrej Jirman
Orange Pi 3 is a H6 based SBC made by Xulong, released in January 2019. It has the following features: - Allwinner H6 quad-core 64-bit ARM Cortex-A53 - GPU Mali-T720 - 1GB or 2GB LPDDR3 RAM - AXP805 PMIC - AP6256 Wifi/BT 5.0 - USB 2.0 host port (A) - USB 2.0 micro usb, OTG - USB 3.0 Host + 4 port USB hub (GL3510) - Gigabit Ethernet (Realtek RTL8211E phy) - HDMI 2.0 port - soldered eMMC (optional) - 3x LED (one is on the bottom) - microphone - audio jack - PCIe Add basic support for the board. Signed-off-by: Ondrej Jirman <megous@megous.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-04-09arm64: dts: allwinner: h6: Introduce Beelink GS1 boardClément Péron
Beelink GS1 is an Allwinner H6 based TV box, which support: - Allwinner H6 Quad-core 64-bit ARM Cortex-A53 - GPU Mali-T720 - 2GB LPDDR3 RAM - AXP805 PMIC - 1Gbps GMAC via RTL8211E - FN-Link 6222B-SRB Wifi/BT - 1x USB 2.0 Host and 1x USB 3.0 Host - HDMI port - S/PDIF Tx - IR receiver - 5V/2A DC power supply Signed-off-by: Clément Péron <peron.clem@gmail.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-04-09arm64: dts: allwinner: h6: move MMC pinctrl to dtsiClément Péron
There is only one pinmuxing available for each MMC controller. Move the pinctrl to the SOC Signed-off-by: Clément Péron <peron.clem@gmail.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-04-05arm64: dts: allwinner: h6: Add device node for SIDYangtao Li
The device tree binding already lists compatible strings for H6 SoC, so add a device node for it. Signed-off-by: Yangtao Li <tiny.windzz@gmail.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
generated by cgit (git 2.34.1) at 2024-05-27 05:03:30 +0000