| Age | Commit message (Collapse) | Author |
|---|
|
This fixes the following DT schemas check errors:
meson-g12b-s922x-khadas-vim3.dt.yaml: gpu@ffe40000: interrupt-names:0: 'job' was expected
meson-g12b-s922x-khadas-vim3.dt.yaml: gpu@ffe40000: interrupt-names:2: 'gpu' was expected
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add minimal thermal zone for two temperature sensor
One is located close to the DDR and the other one is
located close to the PLLs (between the CPU and GPU)
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add cpu and ddr temperature sensors for G12 Socs
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
SimpleFB allows transferring a framebuffer from the firmware/bootloader
to the kernel, while making sure the related clocks and power supplies
stay enabled.
Add nodes for CVBS and HDMI Simple Framebuffers, based on the GXBB/GXL/GXM
support at [1].
[1] 03b370357907 ("arm64: dts: meson-gx: add support for simplef")
Cc: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This adds the Amlogic G12A PCI Express controller node, also
using the USB3+PCIe Combo PHY.
The PHY mode selection is static, thus the USB3+PCIe Combo PHY
phandle would need to be removed from the USB control node if the
shared differential lines are used for PCIe instead of USB3.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The former is going to use the latter to retrieve the efuses data.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The base address of the audio bus and pdm device are different
between the g12 and sm1 SoC families. Overwriting the reg property
only would leave with confusing node names on the sm1.
Move the audio related devices to the g12 dtsi. The appropriate nodes
will be created for the sm1 later on.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The register region size initially is too small to access all
the fifo registers.
Fixes: c59b7fe5aafd ("arm64: dts: meson: g12a: add audio fifos")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the reset to the TDM formatters of the g12a. This helps
with channel mapping when a playback/capture uses more than 1 lane.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The clock controller dedicated to audio clocks also provides reset lines
on the g12 SoC family
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Replace the VPU-centric power domain controller by the generic system-wide
Everything-Else power domain controller and setup the right power-domains
properties on the VPU, Ethernet & USB nodes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
[khilman: minor subject edit: add dts]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This fixes the following DT schemas check errors:
meson-g12a-u200.dt.yaml: reset-controller@1004: compatible:0: 'amlogic,meson-g12a-reset' is not one of ['amlogic,meson8b-reset', 'amlogic,meson-gxbb-reset', 'amlogic,meson-axg-reset']
meson-g12a-sei510.dt.yaml: reset-controller@1004: compatible:0: 'amlogic,meson-g12a-reset' is not one of ['amlogic,meson8b-reset', 'amlogic,meson-gxbb-reset', 'amlogic,meson-axg-reset']
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This fixes the following DT schemas check errors:
meson-axg-s400.dt.yaml: soc: ethernet@ff3f0000:reg:0: [0, 4282318848, 0, 65536, 0, 4284695872, 0, 8] is too long
meson-axg-s400.dt.yaml: ethernet@ff3f0000: reg: [[0, 4282318848, 0, 65536, 0, 4284695872, 0, 8]] is too short
meson-g12a-u200.dt.yaml: soc: ethernet@ff3f0000:reg:0: [0, 4282318848, 0, 65536, 0, 4284695872, 0, 8] is too long
meson-g12a-u200.dt.yaml: ethernet@ff3f0000: reg: [[0, 4282318848, 0, 65536, 0, 4284695872, 0, 8]] is too short
meson-gxbb-nanopi-k2.dt.yaml: soc: ethernet@c9410000:reg:0: [0, 3376480256, 0, 65536, 0, 3364046144, 0, 4] is too long
meson-gxl-s805x-libretech-ac.dt.yaml: soc: ethernet@c9410000:reg:0: [0, 3376480256, 0, 65536, 0, 3364046144, 0, 4] is too lon
while here, also drop the redundant reg property from meson-gxl.dtsi
because it had the same value as meson-gx.dtsi from which it inherits.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The Arm per-CPU architected timers stop ticking in suspend, when the
SCP powers down the CPUs. Flag that in the DT.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
If unspecified in DT, the fifo sizes are not automatically detected by
the dwmac1000 dma driver and the reported fifo sizes default to 0.
Because of this, flow control will be turned off on the device.
Add the fifo sizes provided by the datasheets in the SoC in DT so
flow control may be enabled if necessary.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the ao_pinctrl subnode for the pwm_a function on GPIOE_2.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
To simplify the representation of differences betweem the G12A and G12B
SoCs, move the common nodes into a meson-g12-common.dtsi file and
express the CPU nodes and differences in meson-g12a.dtsi and meson-g12b.dtsi.
This separation will help for DVFS and future Amlogic SM1 Family support.
The sd_emmc_a quirk is added in the g12a/g12b since since it's already
known the sd_emmc_a controller is fixed in the next SM1 SoC family.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
